HP LaserJet - COMMON ERROR CODES

02 WARMING UP MODE
HP 2, 3, 2D, 3D

I/O Cable is bad or hooked up incorrectly

Communication problem between computer and printer
Bad DC Controller
Bad Fuser Assembly
Bad DC Power Supply

HP 3Si, 4Si
Defective display cable or formatter PCA
Bad Fuser Assembly
Bad DC Controller
HP 4V, 5Si
I/O cable is hooked up incorrectly or bad interface in computer
Defective parts such as: fuser, PCA board, DC controller
Bad Fuser Assembly

11 PAPER OUT
ALL

Paper or paper tray empty or not seated correctly

Paper Tray Sensor arm stuck or broken
Defective tray size sensing or configuration
Defective paper control or sensor PCA

Paper cassette is empty or missing

Paper cassette is not seated correctly
Paper out flag PS2 is broken or stuck
Defective DC controller PCA
Tray 1 is empty
Tray 2 is empty

12 OPEN OR NO EP
ALL

13 PAPER JAM (continued)

13 PAPER JAM (continued)

HP 2P, 2P+, 3P, 4P

HP 4, 4+, 5
500 sheet lower cassette not properly adjusted
Check transfer roller to ensure it is seated properly
Bad input sensor, fuser exit sensor or bad paper end sensor
Defective output rollers
Paper stuck in paper path / output unit

HP 1100, 3200 Fax, HP PRINTER 2100, 2200

Printer door open

DC power supply malfunction
Replace DC power supply
External Fuser Door Open
Defective Fan
Sensor switch for the door is dirty or needs to replace
Bad high voltage power supply

HP 4P, 5P

Top cover open

No toner cartridge
Bad toner cartridge
Defective interlock switch assembly
Bad DC controller

HP 4L

Part of the top door that pushes the plunger down is Broken
Top door switch is broken
No toner cartridge
Bad toner cartridge
Bad DC controller

HP 4V, 4MV

Toner cartridge gears worn or damaged

Paper path gears worn or damaged
Defective DC controller PCA
Defective registration guide

HP 5000, 5100

Check paper loaded in paper tray properly

Check the paper length adjuster
Look at the transfer roller assembly for proper adjustment
Check the paper path in printer and duplexer paper (if installed)
Replace or reseat fuser
Check for bad toner cartridge
Check that all assemblies are seated and all doors are closed
Change maintenance kit

HP 5Si, 8000, 8150

4L

12 OPEN OR NO EP (continued)

Paper path door or top cover open

Toner cartridge missing
Toner cartridge not seated in printer
External fuser access door not closed
Tab missing on top cover
Bad DC controller

HP 3Si, 4Si
PS1 malfunction
Fuser bulb burned out
Bad DC controller
HP 4, 4+, 5
Plunger missing on top cover
Paper control P.C.A. malfunction
Bad top cover switch
HP 4V
Front door open sensor
Toner cartridge micro switch malfunction
DC controller PCA malfunction

13 PAPER JAM
ALL

Out of spec media

Pick up roller came out of place
Paper cassettes not correctly loaded
Dirty or obstructed paper path. Paper Jam in paper path
Worn pick up rollers and separation pad
Wrong length paper or incorrect software paper size selected
Defective exit sensor
Defective input sensor doesnt sense paper out
Paper cassettes not correctly loaded
Bad solenoid operation
Bad gear or gears in drive train
Bad main motor or drive circuit
Bad delivery mechanism or coupler gear to main drive
Bad main motor drive circuitry

HP 2, 2D, 3, 3D

Defective sensor cable

Defective registration assembly
Defective fuser
Duplex paper path is obstructed or contains worn Components
Misadjusted or bent switchback assembly

HP 4L, 4P, 5P, 6P

Printer rear door open

Stuck or broken flags or sensors
Paper fragment under oblique rollers
Transfer roller guide not seated
Bad fuser assembly
Bad toner cartridge
Worn pick up roller or regist. assy. block

HP 4, 4+, 5
Rear door open.
Broken or missing cassette paper out sensor flag

Toner cartridge gears worn or damaged

Paper tray feed and separation roller's worn
Paper misaligned in paper tray
Bad input unit
Bad fuser assembly
External input device paper jam. Check all added devices
Paper jammed up in the exit assembly on the left side of printer
Transfer roller assembly out of place or broken
If paper is jammed under toner cartridge change registration or
toner cartridge
Change maintenance kit

Paper jam - make sure paper is loaded properly

Make sure the paper length is adjusted (2200 series)
Check rear door, open and close top cover
Check duplexer
Paper jam internally / under the toner cartridge
Worn pick up and separation pad
Bad fuser assembly
Change maintenance kit
Paper tray overloaded

HP 1000, 1200, 1220mfp, 3300, 3300mfp

Check for paper loaded in paper tray properly

Worn pick up roller and separation pad
Feed roller shaft is bent or warped
Paper stuck in paper path
Bad fuser assembly
Bad shutter on toner cartridge, change toner cartridge
Front door not properly shut

HP2300

Check paper Path / Check paper trays

Check the length adjustment on the paper trays
Check Duplexer
If message persists after all jams have been cleared, a sensor
might be stuck or broken
If jamming persists, change feed rollers and separation pad
Bad fuser assembly
HP 4000, 4050, 4100, 4100mfp

HP 3Si, 4Si

HP 4200, 4300

Miss feed or media jammed in printer. Check entire paper path

Media in duplex unit
Sensor malfunction
Output sensor malfunction (turn off job offset assembly in the
4si only)
Check registration area fuser exit sensor flag and sensor
Bad fuser assembly
Worn feed and separation rollers
Change maintenance kit

HP 5L, 6L, 3100, 3150

Paper not loaded in the paper bin

Bad paper bin sensor
Bad toner cartridge
Bad fuser assembly
Worn pick up rollers and separation kit / Pulling multiple sheets
throuhgh printer
Paper tray overloaded
HP 1005, 1012, 1150, 1300

Check paper in the paper tray

Worn pick up rollers and separation pad
Bad shutter door on toner cartridge - change toner cartridge
Bad fuser assembly
Bad pick up roller shaft and clutch

Ensure paper is loaded in paper tray property

Check feed and separation rollers for unusual wear
Check paper length adjustment in paper tray
Bad fuser assembly
Check paper path in duplexer
Check small belt media roller to ensure that the roller and belt
are feeding the media properly
Check that transfer roller is seated properly
Change maintenance kit

Check for paper loaded in paper tray properly

Check the length adjustment on the paper trays
Check duplexer paper path
Defective printer cartridge, shutter door not opening all the way
Feed and separation roller worn or may have popped off
Jams in stapler / stacker, remove jammed staples
Bad DC controller
Change maintenance kit

HP 4500

Paper jam- check all rear doors

Paper jam- check middle front drawer and duplex drawer
Paper jam- check all drawers
Paper or wrong media in fuser assembly
Worn feed and separation rollers
Bad middle drawer assembly
Bad fuser assembly

Strana 1

13 PAPER JAM (continued)

14 NO EP CART OR NO TONER CAR (continued)

22 EI/O CONFIGURATION ERROR

22 EI/O CONFIGURATION ERRO (continued)

HP 8500

HP 9000

ALL

HP 4600, 5500

Too much data was sent to the EIO card in the specified slot
Press GO to clear the message (data will be lost)
Too much data was sent to the parallel port
Make sure that your using an up to date driver
Check for a loose connection and be sure to use a high-quality
cable - some cables may be missing pin connections

Internal paper jam

Check paper trays for missed loaded paper
Paper jam- check all doors
Paper jam- check duplexer
Paper jam- check mailbox bin
Bad fuser assembly

A page is jammed in tray 2 or tray 3

Verify that media meets specifications and is stored correctly
Clean the indicated tray's feed rollers
Replace the feed and separation rollers

16 TONER LOW

HP 9000

ALL

Toner is uneven in cartridge, shake toner cartridge

Malfunctioning toner cartridge contact points or bad toner
cartridge
Defective high voltage power supply

Paper jam- check trays, all doors, and paper path

Paper jam- check duplexer
Paper jam- internally
Check doors to make sure they are closed
Make sure all feed and separation rollers are properly installed
If paper stops before fuser check transfer assy. or change it
Check fuser assembly for paper stopping at the fuser
Bad DC controller
Paper is jammed at exit assembly - change paper delivery
assembly
Replaced the diverter if the paper still doesn't make out of exit
Replace the flipper assembly
Replace the accumulator assembly
Check all devices on printer run paper path tests with one
device taken off one at a time
Change maintenance kit

Defective high voltage power supply

Defective DC controller
HP 3Si, 4Si

Defective door open sensor flag

Damaged toner level sensor connector
Damaged toner cartridge
Defective DC control PCA
Defective high voltage power supply

ALL

18 MIO NOT READY

No toner cartridge installed or cartridge not fully seated

Missing sensitivity tabs
Bad toner cartridge

ALL

Defective paper control PCA

Defective high voltage unit
HP 3Si, 4Si
Check tabs on right side of toner cartridge
Switch actuator bent, support tab on upper right corner of DC
controller bent or not installed correctly
Defective high voltage unit
HP 4V
Defective toner cartridge micro-switch on high voltage PCA
Malfunctioning front door sensor
Defective DC controller PCA

Printer is not connected to the network or computer

Printer or computer communication problem
Bad jet direct card
Bad formatter board

20 MEMORY OVERFLOW
ALL

Large print job exceeding memory capacity

Too much data or data too complex
Set enhanced I/O to auto mode
Press the GO button or CHECK button -the printer will restart
the print job but some data might be lost
Turn the image adapt and page protect to ON or AUTO to print
the job
Add more memory

HP 4, 4+, 5

21 PRINTER OVERRUN

Defective toner cartridge

Defective high voltage unit or dirty or misaligned contacts

ALL

HP 2300
Worn tray 2 and tray 3 rollers
Change all feed rollers

HP 4, 4+, 5, 5P, 6P
Computer and printer are not communicating
Check the network cable or reseat the cable

HP 2, 3

14 NO EP CART OR NO TONER CART

HP 2, 2D, 3, 3D

I/O configuration for the computer or printer is incorrect

Wrong or damaged I/O cable
Computer is powered off
Damaged printer I/O port
The printer's EIO card in slot X has overflowed its I/O buffer
during a busy state
Error can occur if driver is not IEEE-1284 compliant
Parallel buffer has overflowed
Press GO or CONTINUE to resume printing

Print job too complex, too much data

Turn image adapt and page protect to ON or AUTO to print the
job
Not enough memory
Add more memory

HP 8500
The EIO buffer has overflowed during a busy state
Indicates the parallel buffer has overflowed
error might occur if several complex jobs are sent
simultaneously via the network and are larger allowed
HP 9000

HP 1100, 2100, 2200, 2300, 4000, 4050, 3100 FAX

Too much data was sent to the EIO card in the specified slot or
an incorrect communications protocol might be in use
Check the host configuration
Too much data was sent to the parallel port
Check for a loose connection and be sure to use a high-quality
cable - some cables may be missing pin connections
Make sure that latest version of the printer driver is used

The printer EIO card in slot X has overflowed the I/O buffer
during a busy state
Move the EIO card to different slot
Replace EIO card
The printer parallel buffer has overflowed during a busy state
Reseat the parallel cable
Replace the parallel cable
Replace the formatter board

HP 4200, 4300
The printers EIO card in slot X has overflowed its I/O buffer
during a busy state
Check the configuration of the EIO card and the host computer
If error message persists replace EIO / NETWORK card
The printers parallel buffer has overflowed during a busy state
Check the parallel configuration (High speed to NO and
Advanced functions to OFF.)
Replace the formatter board

23 I/O NOT READY

HP 5000/5100

ALL

Too much data was sent to the EIO card in the specified slot
Press GO to clear the message (data will be lost)
Too much data was sent to the parallel port
Make sure that your using an up to date driver
Check for a loose connection and be sure to use a high-quality
cable - some cables may be missing pin connections

Complex print job

Add more memory

HP 5Si/8000

Complex print job

Add more memory

Using a non HP MIO device

This is an I/O buffer overrun error on the printer's upper slot HP
MIO card

ALL
I/O card is unable to accept data or is not connected to network

24 JOB MEMORY FULL

25 XXX MEMORY FULL

ALL

30 PS ERROR

HP 8150

ALL

Too much data was sent to the EIO card in the specified slot or
an improper communications protocol may be in use
Too much data was sent to the parallel port - this error can
occur if the driver you are using is not IEEE-1284 compliant
Down load & install the latest driver for this printer

An I/O timeout or prompt for user interaction has been

exceeded

HP 4500
Indicates the parallel buffer has overflowed
Memory overflow, print job to large or complex
The EIO buffer for the EIO card in slot "X" has overflowed
during a busy state
Press GO to resume printing, resend job (data will be lost)

30 PS ERROR 22 or 25
All
Unexpected postscript firmware error, replace firmware chip

Strana 2

30 PS ERROR XX (ALL OTHER)

40 DATA TRANSFER ERROR (continued)

41 TEMPORARY PRINT ENGINE FAILURE

41.1, 41.2,41.3 UNEXPECTED PAPER SIZE (continued)

All

HP COLOR 4600, 5500 ERROR 40 BAD SERIAL

TRANSMISSION / BAD EIO CARD

HP 2300, 4200, 4300 ERROR 41.X

HP 5000, 8000

A temporary error has occurred

Turn printer off, then on
Bad DC controller if persists

PCL file being sent to printer while in postscript mode or bad

postscript file or application error
HP 5Si
The optional disk failed a self-test, press GO to continue

A serial data error (parity framing, or line over run) has

occurred during the reception of data
A connection with the EIO card in slot X has been abnormally
interrupted
Check that all cables are connection to the EIO ports and that
the EIO board is seated properly

HP 8500
Device failure
40 DATA TRANSFER ERROR
ALL

Computer and printer may be set to different baud rates

Computer is powered off
Unseated or defective MIO card
Indicates an abnormal connection break occurred while
transferring data from the computer
Turn printer off and reseat the network card
Verify that the printer serial configuration is set the same as the
computer
Check that all cables are connected to the EIO ports and that
the EIO board is seated properly

HP 8500
An EIO accessory connection has been abnormally broken
while transferring data from the computer to the printer
Print an EIO configuration page to verify that the EIO
accessories are installed properly
Check that all cables are connected to the EIO ports and that
the EIO accessory is seated properly
Turn the printer off and on to reset it (data will be lost)

HP 8100,8150 ERROR 41.3

HP 4600, 5500 ERROR 41.1
Unknown misprint error
Turn printer off, then on
41.1, 41.2, 41.3 UNEXPECTED PAPER SIZE
ALL

A serial data error (parity framing, or line over run) has

occurred during the reception of data
A connection with the EIO card in slot X has been abnormally
interrupted
Reseat serial cable or replace the cable
Move the EIO card to a different slot

41 TEMPORARY PRINT ENGINE FAILURE

ALL

HP 2300 ERROR 40
The printer detects a serial data error (parity, framing, or line
overrun) while receiving data from the computer
Press the SELECT button to clear the message

Momentary error
High voltage discharge
Reset unit / Cycle power
Bad formatter PCA board
Bad DC controller board

HP 2300 ERROR 40.X

The connection has been broken between the printer and the
EIO card in the specified slot. (X = slot of the net work card)
Press the select button to clear the error message
Turn printer off and unplug power cord, reseat the EIO card or
the network card

HP 2, 2D, 3, 3D, 2P, 3P

Bad laser scanner cable
Bent or broken fiber optic cable
Paper feed problems

HP 4200, 4300 ERROR 40

HP 2P

A connection with the network card and the motherboard has

been broken abnormally
Print to another network printer to check network configuration
from your computer
Check configuration in the network settings and the printer
network card
Ping printers IP address
Replace the EIO / Network card

For S/N between 2925J00000 and 3047J99999, replace fuser

assembly
HP 5L, 6L, 5P, 6P

Temporary error
Engine error
Power cycle the printer
Replace formatter and DC controller

HP 8100, 8150

HP 5Si, 8000, 4000, 4050

The serial transmission error has occurred
The serial baud rate setting is different than the computer
Reseat the EIO/network card on the printer
Replace the network card

A temporary error has occurred

Turn printer off, then on
Replace the laser scanner
Replace the engine controller board

HP 9000

HP 1200, 2200, 3100 FAX, 3200 FAX, 4100

EIO bad transmission

HP 5000, 8150

Temporary error or misprint error

Replace the laser scanner
Replace the engine controller board

HP COLOR 4500, 4550

HP PRINTRS 1200, 2200, 3100 FAX, 3200 FAX, 4100

Connection with the card in the specified slot has been broken
Check that all cables are connected to the EIO ports and that
the EIO board is seated properly

Replace ECU
Replace laser scanner
Reseat connections to laser scanner and engine controller

Reload the tray with correct media size

Make sure paper tray is loaded properly
Check sensors for proper operation
Worn feed and separation rollers
Make sure the length guide, width guide and size selector
switch on the paper tray have been correctly. Make sure that
paper is under the front paper tabs
Check the control panel setting for the paper size is correctly
configured

Defective connections
Laser scanner connections or bad laser scanner assembly
Paper multi feed or wrong size paper
Paper size selection does not match installed paper
One of the cassettes is overfull or improperly adjusted
Paper is out of spec
Paper pickup and feed rollers are worn, replace rollers
Replace paper input unit
Printer pulls more than one sheet through - worn feed and
separation rollers

The paper size you are trying to print is not the same as the
control panel setting
Make sure the printer settings in the tray's are the same as
control panel and driver
Faulty paper sizing switch on printer
Replace the pick up and separation pad for tray 1
Worn feed and separation rollers
HP COLOR 4600, 5500 ERROR 41.3 UNEXPECTED PAPER
SIZE IN TRAY.
The paper is loaded which is longer or shorter in the feed
direction than the size configured for the tray
Reload the paper in the tray and make sure the length
adjustment is set correctly
Replace the feed and separation rollers
41.2, 41.4, 41.6, 41.7, 41.9 UNKNOWN MISPRINT ERROR

HP 1100, 1200, 2200, 3100, 3200, 4000, 4050, 4100

HP LASER PRINTER 2300 ERROR 41.2, 41.4, 41.6, 41.7, 41.9

Reload the tray with correct media size

Make sure paper tray is loaded properly
Check sensors for proper operation
Worn feed and separation rollers
Make sure the length guide, width guide and size selector
switch on the paper tray have been set correctly and be sure
that paper is under the front paper tabs
Check the control panel setting for the paper size is correctly
configured
HP 2300 ERROR 41.3
Unexpected paper size in tray
Reload the tray with the correct media size
Reconfigure the size in a tray so that contains the size required
for the print job
Typically caused if two or more sheets stick together when
feeding
Change pick up rollers and separation pad
Replace the engine controller board
HP 4200, 4300 ERROR 41.3
The media that is loaded is longer or shorter in the feed
direction that the size that is configured for the paper tray
Print the configuration page and verify that the tray settings
match the media in the tray
Check the paper path sensor flags can move freely
Worn feed and separation rollers
Bad DC controller board

Error 41.2 - Beam detect misprint error

Error 41.4 - No VSYNC error
Error 41.6 - ITB detection error
Error 41.7 - Feed delay error
Error 41.9 - Noise VSREQ error
Turn the printer off and then on the clear the error codes

HP 8100,8150 ERROR 41.1, 41.2, 41.4, 41.5, 41.9

Replace the laser scanner assembly
Replace the engine controller board
HP 4500, 4550
Unexpected paper size
Make sure paper loaded in the paper tray correctly and load the
requested size media in tray
Worn feed and separation rollers
ITB drawer is bad
HP COLOR 4600, 5500 ERROR 41.7, 41.9
A feed delay error and a noise VSREQ error
Turn the printer on and then off
HP COLOR 8500, 8550 ERROR 41.2
Indicates a beam detect laser scanner error
Replace the laser scanner assembly
Replace the DC controller board

Strana 3

41.1, 41.2,41.3 UNEXPECTED PAPER SIZE (continued)

41.1, 41.2,41.3 UNEXPECTED PAPER SIZE (continued)

49 COMM OR CRITICAL FIRMWARE ERRO (continued)

50 FUSER ERROR (continued)

HP COLOR 8500, 8550 ERROR 41.3

HP COLOR 8500, 8550 ERROR 41.5

HP COLOR 4500

HP 2P, 2P+, 3P

The printer was expecting one type of paper from a paper tray
and a different type was feed
Replace OHT sensors
Replace the controller board

Indicates that a critical firmware error has occurred - an invalid

command or data was sent to the formatter causing the
processor to stop
Poor quality parallel cable or network cable
Turn printer off then on
Disconnect the parallel cable and the network cable
If message still there when the network cable is disconnected,
upgrade firmware in jet direct card and the formatter board
Replace firmware DIMM
Replace jet direct card
Replace formatter board

Defective fuser
Temporary error code
Defective AC power supply

HP COLOR 4600, 5500

HP 4, 4+, 5

A critical firmware error has occurred on the formatter.

Try a different software application and see if the job prints. If
the job prints the application that you were using is corrupt
Disconnect the parallel cable or the network cable
Turn printer off and remove all DIMMs and EIO devices from
printer, add one device at a time to determine faulty component
Download the updated firmware for the EIO / Network card and
the formatter board
Replace the EIO / Network card
Replace firmware DIMM
Replace formatter board

Unexpected paper size in paper tray

Verify the paper guides are set correctly
Worn feed and separation rollers
Load the requested size media in tray 1

HP 9000 ERROR 41.1, 41.2

HP 9000 ERROR 41.5

Replace the media with the correct type or reconfigure the tray
to use the current type
Verify application settings

Unknown misprint error

Replace the laser scanner assembly
Replace the upper cable guide assembly
Replace the DC controller board

HP 9000 ERROR 41.3

Unexpected paper size or paper type

Verify standard/custom switch setting
Temporary error- turn printer off then on and resend job
Feed and separation rollers are worn

41.4 OR 41.5 WONG PAPER TYPE

ALL
Defective DC controller or formatter PCA
Usually occurs with smooth media such as labels or
transparencies. Load media one sheet at a time
The media type that is loaded is different than what the tray is
configured to use

49 COMMUNICATION OR CRITICAL FIRMWARE ERROR

HP 1200, 2200, 3100 FAX, 3200 FAX, 4100

This is a communication error code with the application that is
being used
Go back to a different software program and see if a job will
print
If message persists turn printer off then on
Disconnect the network cable and then turn printer off then on
If message still there when the network cable is disconnected,
upgrade firmware in jet direct card and the formatter board
Bad network cable
Bad jet direct card
Replace the firmware DIMM
Replace the formatter board

HP 3Si, 4Si
HP 2300 ERROR 49.XX
Toner cartridge tab broken
HP 1200, 2200, 3100, 3200, 4100
Check sensors for proper operation
HP 2300 ERROR 41.5 UNEXPECTED PAPER TYPE
The printer detected a paper type different from the expected
type
Reload the tray with the correct paper type
Reconfigure the media type that matches the driver setting type
or reconfigure the paper tray type to the printer
HP COLOR 4500, 4550
The paper tray is configured for specific media type, but the
printer detects a different media type loaded
Verify that the correct media is loaded in the input tray and the
printer control panel is configured correctly
Check for paper jam at the registration plate under the ITB
drawer. The engine tries to check the OHT sensor and receives
an error
Replace the ITB drawer
HP COLOR 4600, 5500 ERROR 41.5
The printer senses a different media type in the media paper
path than configured in the paper tray
Configured the driver with the printer paper type settings
Reload the driver or download a new driver from HP

A critical firmware error has occurred on the printer

Turn printer off then on
Disconnect the parallel cable or the network cable
If message still there when the network cable is disconnected
upgrade firmware in jet direct card and the formatter board
Bad network cable
Replace firmware DIMM
Replace the jet direct card
Replace formatter board
Replace engine board

HP 4200, 4300

A critical firmware error has occurred on the printer

Turn printer off then on
Disconnect the parallel cable or the network cable
If message still there when the network cable is disconnected
upgrade firmware in jet direct card and the formatter board
Replace firmware DIMM
Replace the jet direct card
Replace formatter board
Replace engine board

49.24.02 ONLY FOR HP 4200 & 4300

The printer has experienced a critical error
Verify that the ribbon cables are fully seated in the connectors
on the DC controller
Replace the power supply
Replace DC controller
Replace the formatter board

HP 3Si, 4Si

Turn printer off then wait 20 or 30 minutes the turn back on

Improperly seated fuser
Defective fuser
Bad ac power supply
Bad DC controller

Turn printer off , wait 20 or 30 minutes then turn back on

Defective fuser
Defective DC/AC power supply
Change cable from fuser to power supply

HP 4V, 4L, 4P, 5P, 6P

Improperly seated fuser
Defective fuser
Bad engine controller board
HP 5L, 6L

HP COLOR 8500
Indicates that a software or data communications error has
occurred, or corrupt data was sent to the printer
Turn printer off then back on
Remove all EIO cards and reinstall them to ensure they are
seated correctly
If using a parallel connection, verify that the cable is IEEE-1284
compliant
Replace the EIO/Network card
Replace the formatter board

Defective fuser
Defective DC controller
HP 1100, 2100, 4000, 4050
Turn printer off, wait 20 or 30 minutes then turn back on
If printer is hooked up to uninterruptible power supply or surge
protector plug straight in to wall
Replace fuser assembly
Replace engine controller board

HP 9000

HP 1200, 2200, 3100 FAX, 3200 FAX, 4100

Communication or critical firmware error occurred, turn printer

off the back on
Upgrade the firmware to the latest version in the jet direct card
and the formatter board
Replace firmware DIMM
Replace jet direct card and formatter board

Turn printer off, wait 20 or 30 minutes then turn back on

Improperly seated fuser
Defective fuser, replace the fuser assembly
Temporary error code
If the error persists, replace the ECU

HP 2300 ERROR 50.X

50 FUSER ERROR
ALL
Temporary error code, turn printer off then wait 20 or 30
minutes the turn back on
Low or unstable power - check the wall voltage, if on a surge
protector, plug straight in two the wall
Bad fuser assembly
Bad low voltage power supply
Bad DC controller
HP 2, 2D, 3, 3D

Defective fuser cable to DC controller

Defective fuser and AC power supply
Defective fuser
Defective AC power
Temporary error code

A fuser error has occurred

Turn printer of and then on again
Replace the fuser assembly
Replace the engine controller board

HP 4200, 4300
Turn the printer off and allow it to cool down
Make sure that correct fuser (4200 vs. 4300) is installed in the
proper printer
Check connector between fuser and printer, replace if damaged
Bad fuser assembly
Bad DC controller
Bad power supply

Strana 4

50 FUSER ERROR (continued)

51- BEAM DETECT ERROR (continued)

51- BEAM DETECT ERROR (continued)

52 INCORRECT SCANNER SPEED ERROR (continued)

HP 5000, 51000

HP 3SI, 4SI

HP COLOR 4600, 5500 ERROR 51.1, 51.2

HP 1100, 2100, 4000, 4050, 8000

Turn the printer off and allow it to cool down for a minimum of
20 minutes before turning back on
Move the printer to another power source and disconnect it
from any UPS or surge protector
Replace fuser assembly
Replace the power supply
Replace the DC controller

Beam detect error or laser error

Replace the laser scanner assembly
Replace the DC controller board
HP COLOR 4600, 5500 ERROR 51.X0

HP 4, 4+, 5

No color on the print job

HP 2300 ERROR 52.X

HP 5Si, 8000, 8100, 8150

Faulty laser scanner cable connectors

Defective laser scanner assembly

HP COLOR 4600, 5500 ERROR 51.XK, 51.XC, 51.XM, 51.XY

A temporary scanner start up error

Can also be the shutter tab on the print cartridge, replace the
toner cartridge
Replace the scanner assembly
Replace the engine board

Make sure fuser is installed correctly

Bad fuser assembly
Replace fuser cable assembly
Replace DC controller
Replace the low voltage power supply

Defective toner cartridge

Problem with fiber optic cable
Faulty connectors
Poor DC voltage
Defective laser scanner assembly

HP 4V
Problem with fiber optic cable
Defective laser scanner assembly
Defective DC Controller

HP COLOR 4500
HP 4L, 4P, 5P, 5SI

Improperly seated fuser

Defective fuser
Defective DC controller
Replace the power supply board

Temporary error
Laser scanner assembly not seated
Defective laser scanner assembly
Defective DC controller PCA

HP COLOR 4600, 5500 ERROR 50.XX

HP LASER PRINTERS 1100, 2100, 4000, 4050
Turn the printer off and allow it to cool down for a minimum of
20 minutes before turning back on
Reinstall the fuser assembly
Replace the fuser assembly
Replace the fuser power supply or the low voltage power
supply
Replace the DC controller board then calibrate printer
HP COLOR 8500, 8550, ERROR 50.1, 50.2, 50.3, 50.4, 50.6

Improperly seated fuser

Defective fuser
Replace the power supply board
Replace the controller board

HP 9000 ERROR 50.X

Improperly seated fuser

Replace the fuser assembly
Replace the upper cable guide assembly
Replace the low voltage power supply
Replace the DC controller

Beam detect error

Replace laser scanner assembly
Replace Laser scanner cables from scanner to DC controller

Defective laser scanner assembly

Defective wiring harness to the DC controller
Defective DC controller
Replace laser scanner assembly

HP 9000

Temporary laser assembly error, turn printer off then on

Replace laser scanner assembly
Replace upper cable guide assembly
Replace DC controller board

Printer scanner speed error has occurred

Replace laser scanner assembly
Replace the DC controller assembly
HP COLOR 4600, 5500 ERROR 52.XK, 52.XC, 52.XM, 52.XY

Error code K - No Black color

Error code C - No Cyan color
Error code M - No Magenta color
Error code Y - No Yellow color
Replace laser scanner assembly
Replace the DC controller assembly

HP 5000, 5100

Defective cable laser scanner to DC controller

Defective laser scanner assembly

HP 2P, 2P+, 3P

HP 8100, 8150

HP 5000, 5100

Bad scanner motor

Bad DC controller

A loss of beam detect occurred

Replace the scanner cables to DC controller
Replace the scanner assembly

HP 3Si, 4Si, 4V

Temporary error, bad toner cartridge

Laser scanner assembly not seated
Defective laser scanner assembly
Reseat cables to the laser scanner and ECU
Bad engine board

HP 4200, 4300 ERROR 51.XX

HP 8100, 8150

Printer has a beam detect error

Replace the laser scanner assembly

Defective toner cartridge

Bad cable from laser scanner assembly to DC controller
Cuts or kinks in fiber optic cable
Defective laser scanner assembly

HP 2, 2D, 3, 3D

HP 2P, 2P+, 3P

HP 4200, 4300 ERROR 52.XX

HP COLOR 8500

52 INCORRECT SCANNER SPEED ERROR

51- BEAM DETECT ERROR

HP 2, 2D, 3, 3D

Error code K - No Black color

Error code C - No Cyan color
Error code M - No Magenta color
Error code Y - No Yellow color

HP 1200, 2200, 2300, 3100 FAX, 3200 FAX, 4100

Improperly seated toner cartridge

Improper laser shutter operation
Damaged fiber optic cable
Bad laser assembly

Scanner start up error

Replace scanner cable from engine board to scanner assembly
Replace scanner assembly
Replace the engine board
Replace the DC controller only on the 8000

Printer has a beam detect error

Replace the cable assembly from scanner to DC controller
Replace the scanner assembly
Replace the DC controller

HP COLOR 4500, 4550

Defective laser scanner assembly

Defective DC controller
Defective wiring harness from the scanner to the DC controller
Replace the scanner assembly

Faulty cable assembly

Scanner motor problem
Defective laser scanner assembly
Defective DC controller

HP 4, 4+, 5
Faulty laser scanner cable
Defective laser scanner assembly
HP 4L, 4P, 5P, 5L, 5Si

Temporary error, scanner startup failure

Improperly fitted scanning assembly/ scanner cable
Defective laser scanner assembly
Defective DC controller board

HP 1200, 2200, 3100 FAX, 3200 FAX, 4100

Printer scanner speed error has occurred

Replace laser scanner assembly
Replace the DC controller assembly
Replace cable assembly from scanner to DC controller

Laser scanner error, start up / rotation error

Replace laser scanner assembly
Replace DC controller board
Replace cable assembly from scanner to DC controller

HP 4500, 4550
Temporary error, laser scanner start up / rotation error
Replace laser scanner
Replace DC controller assembly
HP COLOR 4600, 5500

Laser scanner error, start up / rotation error

Take the toner cartridges out and reseat or replace
Replace laser scanner assembly
Replace DC controller board

HP 8500, 8550
Temporary error, laser scanner start up / rotation error
Replace laser scanner motor
Replace DC controller assembly

Temporary error, scanner rotation error

Replace contact image sensor
Replace laser scanner
Replace cables between laser scanner and engine board

Strana 5

52 INCORRECT SCANNER SPEED ERROR (continued)

Remove DIMM and put into different slot

Replace bad DIMM chip that caused the error

HP 9000

HP 4200, 4300
Temporary error, laser scanner start up / rotation error
Replace laser scanner
Replace upper cable guide assembly
Replace DC controller

53 ACCESSORY MEMORY ERROR

HP 2, 2D
Accessory memory failure
Replace memory card
HP 3, 3D

Failure in front memory slot

Failure in rear memory slot
Replace memory card
Replace formatter board

HP 2P, 2P+, 3P
Replace memory card
HP 3Si, 4Si
Temporary error
Laser malfunction
HP 4, 4+, 4P, 4Si, 4V, 5, 5P, 5Si
SIMM malfunction
Replace SIMM chip
Replace formatter board
HP 4L, 5L
An error has been found in the RAM
Defective or incompatible memory card
Defective formatter board
HP 1200, 2200, 3100, 3200, 4100 ERROR 53.XX

Temporary DIMM error

Unsupported memory size
Invalid DIMM speed
DIMM RAM parity error
Try the DIMM in a different slot
Unable to make a temporary mapping in the printer
Replace all the DIMM memory
Make sure proper memory DIMM is installed
Replace formatter board

HP ERROR 2300 53.XX.ZZ

The printer has a problem with the memory DIMM

Unsupported memory presence detect bad
Reseat all the memory
Unsupported memory size

An error occurred in the printer memory

Unsupported memory
Unrecognized memory
Unsupported memory size
Reseat all DIMMs
Replace bad DIMMs
Replace formatter board

HP 8100, 8150

Error has occurred on some memory

Unsupported memory
Unrecognized memory
Exceeded maximum ram size
Invalid DIMM speed
DIMM address conflict
Unable to make a temporary mapping
Remove DIMM and put into different slot
Replace bad DIMM that caused the error

HP COLOR 4500, 4550

Temporary DIMM error
Replace DIMM
Replace formatter board
HP COLOR 4600, 5500 ERROR 53.XO.ZZ
An error has occurred in the onboard RAM
Turn the printer on and then off
HP COLOR 4600, 5500 ERROR 53.XY.ZZ

Error has occurred on some memory

Unsupported memory
Unrecognized memory
Exceeded maximum ram size
Invalid DIMM speed
Remove DIMM and put into different slot
Replace bad DIMM chip
Replace the formatter board

HP COLOR 4600, 5500 ERROR 53.10.05

A DIMM is installed in both 168 - pin DIMM slot 4 and 100 - pin
DIMM slot 5
Remove one or all the DIMMs or move one of the DIMMs to a
different slot
HP COLOR 8500
Temporary DIMM error
Install DIMM in a different slot. The DRAM DIMMs must be
installed in synchronous pairs in adjacent slots, with the same
size and speed in both slots. Only SDRAM is supported.
Replace DIMM chip
Replace formatter board

HP LASER PRINTER 5000, 5150

HP 9000

Error has occurred on some memory

Unsupported memory
Unrecognized memory
Maximum ram size exceeded
Invalid DIMM speed

Temporary DIMM error

Install DIMM chip in a different slot
Replace DIMM chip
Replace formatter board

54 - PRINTER ERROR CYCLE POWER

54 - PRINTER ERROR CYCLE POWER (continued)

HP 2D, 3D

HP COLOR 4600, 5500 ERROR 54.19

Improperly fitted duplex shift plate

Bad PS5 or SL4
Main motor defect

Replace the DC controller board

HP 5Si, 8000

Replace toner level sensor PCB.

Replace DC controller

Defective duplexer

HP COLOR 4600, 5500 ERROR 54.21, 54.22, 54.23, 54.24

HP 8500, 8550 ERROR 54.1

HP 1200, 2200, 3100, 3200, 4100
Temporary error
Replace formatter
Remove tab from toner cartridge and reinstall the toner
cartridge
Try another wall outlet, remove the printer from any UPS
supplies, additional power supplies, or power strip
HP 4200, 4300
The toner cartridge was installed with the sealing tape in place
Remove sealing tape (pull tab) and reinstall the toner cartridge
Replace the toner cartridge unless cartridge is damaged
HP COLOR 4500, 4550 ERROR 54.1

Indicates that an internal power failure has occurred

Check the fuser for paper jams.
Replace the low-voltage power supply
Replace the high-voltage power supply

Indicates that the temperature/ humidity sensor has

malfunctioned
Replace the cross member assembly, which includes the
temp/humidity sensor
Replace the controller board
HP 8500, 8550 ERROR 54.2
A carousel rotation error
Reseat all toner cartridges and make sure the toner lock lever
is fully locked on all toners
Replace the carousel stopper solenoid
Replace the black toner cartridge on/off switch
Replace the carousel motor
Replace the controller board
Replace the main relay PCA
HP 8500, 8550 ERROR 54.3
Indicates a density sensor error/
Replace the density sensor

HP COLOR 4500, 4550 ERROR 54.2

HP 8500, 8550 ERROR 54.4

Indicates that a problem with the carousel assembly

Remove all toner cartridges, reseat and check for obstruction
Replace the brake release
Replace carousel drive motor
Replace the rotary drive assembly

Waste toner sensor has failed

Replace the waste toner sensor assembly
Replace the imaging drum

HP COLOR 4500, 4550 ERROR 54.3

55 - INTERNAL COMMUNICATION PROBLEM

The printer has a density sensor problem

Replace the density sensor

ALL

HP COLOR 4500, 4550 ERROR 54.4

Defective DC controller board

Defective formatter board
Inadequate site power surge protector - HP 4V

Indicates a waste toner sensor malfunction

Replace the waste toner sensor

HP 4V

HP COLOR 4500, 4550 ERROR 54.6

Defective laser scanner assembly

The OHT sensor has reported an error

Replace the ITB drawer

HP 3Si, 4Si

HP COLOR 4600, 5500 ERROR 54.1

Check the fuser assembly
HP COLOR 4600, 5500 ERROR 54.3, 54.5, 54.6, 54.11, 54.12,
54.13, 54.14, 54.20
Replace all toner cartridges
Replace the color registration detection assembly
HP COLOR 4600, 5500 ERROR 54.7, 54.8, 54.9, 54.10
Replace the drum phase sensor for the indicated color

Improperly fitted connectors

Loose or bad cable
Defective DC controller
Defective DC power supply
Defective formatter board
Defective paper input PCA board
Defective main motor

HP 5Si, 8000, 8100, 8150

Loose or bad cable from DC controller and laser scanner
assembly
Defective laser scanner assembly
Defective DC controller board
Defective formatter board

Strana 6

55 - INTERNAL COMMUNICATION PROBLEM (continued)

56 - PRINTER DEVICE ERROR

57 - ERROR

57 - ERROR (continued)

HP 5Si, 8000, 8100, 8150 (ERROR 55.A)

HP 2D, 3D

HP 3, 3D

HP 4200, 4300 ERROR 57.7

Change fuser
Change wiring harness between DC controller and fuser
Change DC controller board

Output selector knob not in duplex position

Incompatible memory card in front slot

Incompatible memory card in rear slot

The cooling fan in the optional duplexer is bad

Replace the duplexer fan

Trying to print envelope in duplex mode

HP 2P, 2P+, 3P

HP 5000, 5100

HP 1100, 2100, 4000, 4050

Replace formatter board
Replace DC controller Board
Replace engine board

HP 1100, 1200, 2100, 2200, 3100 FAX, 3200 FAX, 4000, 4050,
4100, 8000

Fan error
Change bad fan
Change DC controller

HP 1200, 2200, 3100 FAX, 3200 FAX, 4100

Defective DC controller
Check cable to the ECU
Replace ECU
Defective formatter
Defective firmware DIMM

HP 3Si, 4Si

Temporary error, turn printer off and back on

Check printer configuration
Verify the accessory connection
HP 2300

Incompatible memory card

A temporary printing error, incorrect input or output request

Turn printer power off and then on

HP 4, 5, 4L, 5P

HP 8100, 8150 ERROR 57.3

Fan 2 or the low-voltage power supply fan has an error

Replace fan (FM2)
Replace DC controller board

HP 4200, 4300 ERROR 56.1

Unknown input device installed, remove all non HP devices

Reinstall all paper input trays

HP 4200, 4300 ERROR 55.X

The DC controller is not communicating with the formatter
Replace DC controller board
Replace formatter board
HP 5000, 5100
An internal communication error occurred
Replace DC controller board
Replace formatter board
HP COLOR 4500, 4550 ERROR 55.X
Communication error between formatter and DC controller
Replace DC controller board & recalibrate the DC controller
board and formatter board
Replace the formatter board
Initialize NVRAM
HP COLOR 8500
Temporary error
Communication error between printer and the controller
Replace the controller board
HP 9000

Reseat formatter, DIMMs and EIO cards

Perform an engine test
Perform a service test
Replace DC controller board
Replace the formatter board

HP 8100, 8150 ERROR 57.2

Fan 3 or the formatter fan has an error
Replace fan FM3
Replace DC controller board

HP 2300 ERROR 55.XX AND ERROR 55.A, 55.B, 55.C, 55.D

No engine response
Excessive glitches
Communication timeout
Bad tray bin reports
Incoming parity error
Outgoing parity error
Hung communications
Invalid bus timeout
Try a different printer diver or print a smaller file
Try printing from a different application

Incompatible memory card in top slot

Incompatible memory card in bottom slot
Poorly seated motor cables or connectors
Defective main motor
Defective DC controller board

HP 5L, 6L

Main motor not functioning properly

Change toner cartridge
Change main motor
Change DC controller

HP 8100, 8150 ERROR 57.5

HP 3Si, 4Si - 57.1

HP 4200, 4300 ERROR 56.2

Unknown output device installed
Reinstall the stacker or stapler/stacker
Remove all non-HP paper handling devices
HP 5000, 5100
A temporary printing error occurred
Illegal input or Illegal out put
Bad accessory connection
HP LASER PRINTER 8100, 8150
Illegal input and Illegal out put
Turn printer off and back on
Check the printers configuration
HP COLOR 8500, 8550 ERROR 56.1
Indicates an input feed error
Trying to print transparencies through the duplexer
Make sure all paper trays are installed correctly

Gears seized
Faulty top cover switch
Faulty ac kill switch operation
Improperly fitted connector on DC controller
Bad main motor PCA or main motor

HP 4+ - 57.1
Gears seized
Bad Main motor
Bad DC controller
HP 3SI, 4SI, 4+, 5SI
Faulty fan motor
Fan on main body
Duplexer fan

Output error or there are transparencies in the duplexer

Remove all paper in the printer

Illegal input selection

Check printer configuration
Check application settings
Re-install the duplexer with the printer power off
Replace the duplexer assembly

HP 8100, 8150 ERROR 57.9

Replace fan 5 or tray 1 fan
Replace DC controller board
HP COLOR 4500, 4550 ERROR 57.1
The printer has detected the exhaust fan is bad
Replace exhaust fan located in the upper rear left corner

The printer has detected bad exhaust fan

Replace exhaust fan located in upper rear right corner
HP COLOR 4500, 4550 ERROR 57.3

A fan error has occurred

The number after the 57 is the fan # (ex. 57.1 = fan motor 1)
Replace the bad fan
Replace the engine controller board

Replace the drum drawer assembly

HP COLOR 4600, 5500 ERROR 57.3

HP 4200, 4300 ERROR 57.3

Replace fan motor (FM3) cartridge fan

Replace DC controller board

A printer fan is not functioning

Replace fan (FM2)
Replace the DC controller

HP COLOR 4600, 5500 ERROR 57.4

HP 9000 ERROR 56.2

HP 4300 ONLY ERROR 57.4

Duplexer removed while printer power is on

Check printer configuration
Check application settings
Re-install the duplexer with the printer power off
Replace the duplexer assembly

Fan 4 or the face down delivery assembly

Replace fan 4
Replace DC controller board

HP COLOR 4500, 4550 ERROR 57.2

Check the fan connector and make sure fan is not blocked
Replace the fan
HP 2300 ERROR 57.X

HP 8100, 8150 ERROR 57.6

HP 1200, 2200, 3100, 3200, 4100

HP COLOR 8500, 8550 ERROR 56.2

HP 9000 ERROR 56.1

The fan 1 or the laser / scanner fan has occurred

Replace fan 1
Replace DC controller board

A printer fan is not functioning

Replace fan (FM1)
Replace the power supply
Replace the DC controller

Replace fan motor (FM2) formatter fan

Replace DC controller board
HP COLOR 4600, 5500 ERROR 57.7
Replace fan motor (FM2) power supply fan
Replace low-voltage power supply
Replace DC controller board

Strana 7

57 - ERROR (continued)

58 MEMORY SENSOR ERROR (continued)

59 MAIN MOTOR ERROR (continued)

59 MAIN MOTOR ERROR (continued)

HP COLOR 8500, 8550 ERROR 57.1

HP 4200, 4300 ERROR 58.3

HP LASER PRINTER 2300 ERROR 59.7, 59.8

HP COLOR 4600, 5500 ERROR 59.3, 59.4

Replace DC controller board

HP 4200, 4300 ERROR 58.4

Image drum motor error

Replace image drum motor
Replace DC controller board

A fuser motor error

Replace fuser drive assembly
Replace DC controller board

Replace power supply

HP LASER PRINTER 2300 ERROR 59.9, 59.A

HP COLOR 4600, 5500 ERROR 59.5, 59.6

HP COLOR 8500, 8550 ERROR 57.2

HP 8100, 8150 ERROR 58.1, 58.2, 58.3, 58.4

The ETB / ITB motor error

Replace ETB / ITB motor assembly
Replace DC controller board

A print cartridge motor error

Replace drum drive assembly
Replace DC controller board

HP 2300 ERROR 59.B, 59.C

HP COLOR 4600, 5500 ERROR 59.9, 59.A

The Alienation motor error

Replace the alienation motor
Replace the DC controller board

ETB motor error

Replace EBT motor assembly
Replace DC controller board

HP 2300 ERROR 59.D, 59.E

HP COLOR 4600, 5500 ERROR 59.B, 59.C

A registration motor error

Replace registration motor
Replace DC controller board

A developing disengaging motor error

Replace the developing disengaging drive assembly
Replace DC controller board

HP 4200, 4300 ERROR 59.00, 59.10, 59.20

HP 8500, 8550

Fan error. One of the cooling fans is bad

Replace fan 1
Replace the carousel motor
Replace the main relay PCA
Replace the power supply

Fan error. One of the cooling fans is bad

Replace fan 2
Replace the carousel motor
Replace the main relay PCA
Replace the power supply

HP COLOR 8500, 8550 ERROR 57.3

Fan error. One of the cooling fans is bad

Replace fan 3
Replace the carousel motor
Replace the main relay PCA
Replace the power supply
Replace the controller board

HP 9000 ERROR 57.1, 57.2, 57.3, 57.4, 57.5, 57.6

Temporary Printer error has occurred with one of the fans
Replace fan motor that goes with the error code. (EX. 57.1
means fan motor 1)
Replace DC controller
58 MEMORY SENSOR ERROR
HP 4, 4L, 4P, 4V, 5, 5P
Improperly fitted fan cable
Defective DC controller PCA
Defective fan

Paper tray lift malfunction

58.1 - Change tray 1 input unit
58.2, 58.3 - Change tray 2/ 3 input unit
58.4 - Change tray 4 lift motor

HP COLOR 4600, 5500 ERROR 58.3, 58.4

A memory tag error was detected

Replace memory PCB
Replace DC controller
Replace power supply

HP COLOR 8500, 8550 ERROR 58.1

Indicates that the paper diverter inside the right upper door is
out of position, causing an error feeding media from tray 1
Replace the pick up and separation pad on tray 1
Replace try 1 input unit
HP 9000

Check printer configuration

Replace toner cartridge
Replace toner contact sensor assembly
Replace DC controller

HP 4300 ONLY ERROR 59.A, 59.4

HP 3Si, 4Si

HP 1100, 1200, 2100, 2200, 3100, 3150, 3200, 4000, 4050, 4100

Improperly inserted paper cassette

Main motor error

Check the main motor cable is seated properly
Check gear movement in the drive train around the fuser and
toner cartridge
Replace main motor
Replace DC controller

Replace ECU
Replace environmental thermistor
Replace toner cartridge
Replace memory controller PCB
Replace cartridge memory antenna assembly

HP 2300 ERROR 58.XX

A printer memory tag CPU error was detected

Plug printer into a dedicated power source or wall out let
Test the wall outlet for proper voltage and ground
Replace Air generator sensor
Replace CPU
Replace Power supply

The main motor is not functioning correctly

Replace main motor
Replace DC controller board

HP 3SI, 4SI
Not enough memory installed to support application being used

Temporary main motor error, M4 not working

Replace main motor M4
Replace main relay PCA
Replace sub relay PCA
Replace DC controller board

HP 4200, 4300 ERROR 59.2

59 MAIN MOTOR ERROR

58.1 OR 58.2

HP LASER PRINTERS 1200, 2200, 3100, 3200, 4100

A Temporary printer motor error has occurred

Main motor error has occurred
Replace main motor assembly
Replace DC controller board

Print Cartridge motor has occurred

Replace toner cartridge
Replace print cartridge motor
Replace DC controller board

HP 9000 ERROR 59.0, 59.1, 59.2

Temporary motor error has occurred

Replace toner cartridge
Replace main motor
Replace DC controller

HP 9000 ERROR 59.3

Replace fuser assembly
Replace Fuser motor
Replace DC controller

HP 5Si, 8000, 8100, 8150

Temporary main motor error
Change main motor
Replace DC controller
HP 5000, 5100

60 - FORMATTER, MEMORY, MAIN MOTOR

HP 4, 4+, 4P
Defective formatter board
Replace formatter board

HP 2300 ERROR 59.0, 59.1, 59.2

A temporary printer main motor error has occurred
Replace the main motor
Replace the DC controller board

Temporary main motor error

Change main motor
Replace DC controller

HP 3Si, 4Si, 4V
Defective memory SIMMs
Replace memory SIMMs

HP COLOR 4500, 4550

HP 2300 ERROR 59.3, 59.4
Fuser motor error
Replace fuser motor assembly
Replace the DC controller board

HP 4200, 4300 ERROR 60.2

Temporary main motor error
Change main motor assembly
Replace DC controller board

Tray 2 lift motor error has occurred

Replace tray 2 lift drive assembly
Replace DC controller board

HP COLOR 4600, 5500 ERROR 59.0, 59.1, 59.2

HP 4200, 4300 ERROR 58.2

HP 2300 ERROR 59.5, 59.6

Replace air -temperature sensor

Replace power supply

Print cartridge motor error

Replace the print cartridge motor
Replace the DC controller board

HP 4200, 4300 ERROR 60.3

Main motor error
Replace main motor
Replace DC controller board

Tray 3 lift motor error has occurred

Replace tray 3 lift drive assembly
Replace DC controller board

Strana 8

60 - FORMATTER, MEMORY, MAIN MOTOR (continued)

62 - MEM ERROR, DEFECTIVE FORMATTER BD. (continued)

63 - DEFECTIVE FORMATTER BOARD

64 - SCAN BUFFER ERROR (continued)

HP 4200, 4300 ERROR 60.4

HP 2100, 3100 FAX, 4000, 4050, 8150

HP 2, 2D, 2P, 2P+, 3, 3D, 3P, 4P, 4, 4+, 5, 5P, 6P

HP COLOR 4600, 5500

Tray 4 lift motor error has occurred

Replace tray 4 lift drive assembly
Replace DC controller

Temporary memory error

Reseat all memory or Replace all memory
Replace formatter board

Defective formatter Board

Replace the formatter board

A scan buffer error

Replace firmware DIMM
Replace formatter board

HP 9000 ERROR 60.2 (TRAY 2), 60.3 (TRAY 3)

HP 2300

HP 4V
HP LASER PRINTER 9000

The paper in the paper tray is not lifting the media to the top
Check tray for obstruction. Reload paper in tray and make sure
it is properly straight in paper tray
Remove and Reseat paper tray. And swap trays 2 and trays 3
Replace PJ4

No system found
The printer software system is corrupt
Turn printer power off, then back on

HP 5Si, 8000

HP 5L, 6L

61 - FORMATTER, MEMORY ERROR

Defective formatter board

Replace formatter board

Defective formatter board

Replace formatter board

HP 4200, 4300 ERROR 62.0

HP 3Si, 4Si

Defective formatter board

No system firmware image was found

Replace firmware DIMM
Replace formatter board

HP 3Si, 4Si, 4V

Defective formatter board

Defective SIMM
Replace SIMM
Replace formatter board

Temporary scan buffer error

Turn printer off then on
Replace laser scanner
Replace DC controller

65 - DEFECTIVE FORMATTER BOARD

ALL

ALL
Improperly fitted SIMMs. Reseat the memory SIMMs
Bad memory SIMM chip. Replace memory SiMMs
Replace formatter board.
HP 2, 2D, 2P, 2P+, 3, 3D, 3P, 4P
Defective formatter board
Replace formatter board

HP 8100, 8150 ERROR 62.0

The internal memory
Replace formatter board

HP 3Si, 4Si, 4V
Defective memory SIMMs
Reseat memory SIMMs or Replace memory SIMMs
HP 5Si
Defective formatter board
Replace formatter board

1, 2 or 3 is slot on formatter where bad DIMM is located

Replace bad DIMM or replace all the DIMMs
Replace formatter board

ALL

HP COLOR 4500, 4550 ERROR 62.X

Internal memory error

Replace the memory DIMMs

Defective memory SIMMs

Reseat memory SIMMs or Replace bad memory SIMMs

64 - SCAN BUFFER ERROR

Temporary external paper device error

Reset external paper handling device
Check and reseat all cables between printer and the specified
device
Turn printer off and on
Replace external paper handling device
Replace the printer formatter board

ALL
Temporary formatter board error, power cycle printer
Replace the formatter board

No system was found

Turn printer off and on
Reseat firmware DIMM, make sure it is in the 168-pin slot J1
Replace firmware DIMM
Replace formatter board

HP 3200
Problem with internal memory
Replace all memory DIMMs

Temporary formatter board error

Perform a cold reset
Replace formatter
Replace firmware DIMMs

HP 2300

A temporary scan-buffer printing error

Turn printer off and on
Reseat jet direct card
Replace jet direct card
Replace formatter board

HP COLOR 4500, 4550, 8500, 8550

HP 9000

HP 4100

Internal memory error

Reseat memory DIMMs
Replace all memory DIMMs
Replace formatter board

Problem with internal memory

Move DIMMs to different slot
Reseat all memory DIMMs
Replace all memory DIMMs
Replace the formatter board

HP 1100,1200,2100, 2200, 3100,3150, 3200, 4000, 4050, 4100

HP 5SI

HP 1100, 1200, 2200, 3100, 3150, 3200, 4000, 4050, 4100

HP COLOR 8500, 8550

Temporary formatter error
Replace the formatter board

66 EXTERNAL PAPER HANDLING DEVICE ERROR

The firmware ran out of memory

Check the printer settings

Indicates a DR-RAM error

Replace the DR-RAM error
Replace the formatter board

Indicates that the internal RAM memory test failed.

Replace the bad DIMMs
Replace formatter board

Replace DC controller board

HP COLOR 4600, 5500

HP 3Si, 4Si, 4V

HP COLOR 8500, 8550

HP COLOR 4500, 4550 ERROR 62.M

HP 2, 2D, 2P, 2P+, 3, 3D, 3P, 4P

Defective formatter board
Replace formatter board

HP 8500, 8550
Defective formatter board
Replace formatter board

HP COLOR 4500, 4550 ERROR 62

62 - MEMORY ERROR, DEFECTIVE FORMATTER BOARD

2. Replace formatter board.

3. Defective SIMMs
4. Replace SIMMs

HP 1100, 2100, 3100, 3150 FAX, 4000, 4050

HP 8100, 8150 ERROR 62.1, 61.2, 61.3

Firmware error, turn printer off then on

Replace Firmware DIMMs

Improperly fitted SIMMs or font cartridge

Defective internal memory
Defective SIMM slot
Defective font cartridge
Replace memory DIMMs
Replace formatter board

Defective SIMMs
Defective formatter board
Replace memory SIMMs
Replace formatter board

Temporary scanner buffer error

Clear print queue
Turn printer off then on
Replace firmware DIMM
Replace formatter board

HP 4200, 4300 ERROR 66.00.15

The stacker or stapler/ stacker was remover and replaced while
the printer power was on
Turn the printer power off and verify that the stacker or stapler/
stacker is installed correctly
Turn the printer power on
HP 4200, 4300 ERROR 66.12.01, 66.12.02, 66.12.03
A stacker or stapler/ stacker error has occurred
Replace the stapler unit
Replace the stapler/ stacker unit
HP 5Si, 8000
Temporary external paper device error
Make sure that paper is loaded in paper tray correctly
Check all external paper handling devices. Remove all paper
handling devices
Put one external paper handling devices on the printer one at a
time
Replace the defective paper-handling device
Replace the formatter board

Strana 9

66 EXT. PAPER HANDLING DEVICE ERROR (continued)

66 EXT. PAPER HANDLING DEVICE ERROR (continued)

68 - ERROR IN NVRAM, SVC ERROR NVRAM FULL (cont.)

68 - ERROR IN NVRAM, SVC ERROR NVRAM FULL (cont.)

HP 5000, 5100

HP 9000 ERROR 66.12.40

HP 3Si, 4Si, 4V

HP COLOR 4500, 4550

An error occurred in an external paper-handling device

Check all external cables to the paper handling devices
Reseat all paper handling devices, replace one device at a time

The offset module error

Replace offset module assembly
Replace output device controller PCA board

Defective SIMMs
Replace memory SIMMs

NVRAM error
Change formatter board

HP 5, 5Si 68 ERROR
HP 4500, 4550

HP 9000 ERROR 66.12.60

Check all cables on the external paper handling output Device

The EEPROM on the controller PCA is damaged

Replace output device controller PCA board

Remove EIO / network card (will be reset if not removed)

Perform NVRAM initialization
If problem persists, replace formatter board

HP COLOR 4600, 5500 68.0, 68.1 PERMANENT STORAGE

ERROR, PERMANENT STORAGE FULL, PERMANENT WRITE
FAILED

HP 9000 ERROR 66.12.70

HP 1200, 2200, 3100, 3150, 3200, 4100 68 ERROR

The EEPROM on the controller PCA is damaged

Replace output device on controller board

Remove EIO / network card (will be reset if not removed)

Print a configuration page and check the printer settings to
determine which values have changed
Hold down Cancel Job Button while turning the printer on

HP 8500, 8550 ERROR 66

Communication error between sheet input unit or the Multi-bin
mailbox and the printer
Turn printer off and then turn printer on
HP 8500, 8550 ERROR 66.11

67 - SERVICE/PRINTER ERROR

HP 2, 2D, 2P, 2P+, 3, 3D, 3P, 4, 4+, 5, 4P

Indicates a 2000- sheet input unit lifting motor error

Make sure that the paper lifting plate moves freely by hand
Replace the paper deck drive assembly
Replace the paper tray unit feeder assembly

Reseat any printer accessories

Defective formatter board

HP 8500, 8550 ERROR 66.11.02

HP 4Si

Indicates a 2000- sheet input unit feed motor error

Replace tray 4 pick up assembly
Replace the paper deck drive assembly

Temporary printer error

Defective paper guide plate assembly
HP 4V

HP 8500, 8550 ERROR 66.11.03

Indicates a 2000- sheet input unit feed and lifting motor error
Check that pick up rollers are installed properly
Replace paper deck drive assembly
Replace tray 4 pick up assembly

HP 8500, 8550 ERROR 66.22.08

Temporary printer error

Defective paper guide and plate assembly
HP 5Si
FRU not installed properly
Reinstall the FRU

HP 1200, 2200, 3100, 3150, 3200, 4100 ERROR 68.X

PERMANENT STORAGE FULL
Print a configuration page and check the printer settings to
determine which values have changed
Remove EIO / network card (will be reset if not removed)
Hold down Cancel Job Button while turning the printer on
Replace the formatter
HP 1100, 2100, 4000, 4050, 8000, 8100, 8150 ERROR 68
NVRAM FULL
Print a configuration page and check the printer settings to
determine which values have changed
Remove EIO / network card (will be reset if not removed)
Hold down Cancel Job Button while turning the printer on
Replace formatter board

If 68.0 error persists, execute an NVRAM inititialization

Use HP Web jet admin software to delete files from the disk
drive
Reinitialize hard disk
Replace hard disk
Replace formatter board
HP COLOR 8500, 8550 ERROR NVRAM SETTINGS CHANGED

Recoverable error detected in NVRAM

Perform a cold reset
Replace NVRAM DIMM
Replace formatter board

HP COLOR 8500, 8550 ERROR NVRAM FULL SETTINGS

LOST
Indicates that the NVRAM is full and the printer is unable to
write new data
Perform a cold reset
HP 9000 ERROR 68.X NVRAM OR HARD DISK PERMANENT
STORAGE WRITE FAILURE
Reseat the hard disk
Reinitialize the hard disk
Replace the hard disk

HP 2300 ERROR 68.X STORAGE ERROR

HP 9000 ERROR 68.0 PERMANENT STORAGE

Multi-bin mailbox flipper motor error

Replace the flipper assembly
Replace the multi-bin mailbox controller board
HP 8500, 8550 ERROR 66.22.09
Multi-bin mailbox external memory error
Replace the multi-bin mailbox controller board
HP 8500, 8550 ERROR 66.22

67 MEMORY ERROR
HP 3Si, 4Si, 4V
Defective SIMMs
HP 8500
Replace controller board
68 - ERROR IN NVRAM, SERVICE ERROR NVRAM FULL

Indicates a multi-bin mailbox error

Replace the multi-bin mailbox controller board

ALL

HP 9000 ERROR 66.11.00

Temporary error, Cycle power on and off

Defective formatter board

Temporary external paper input device error

Check for extra media in tray 4
Replace the input device

HP 5P, 6P 68 ERROR

HP 9000 ERROR 66.12.20

Retainer sensor error
Replace the accumulator assembly
Replace the output device controller PCA board
HP 9000 ERROR 66.12.21
Bearing bracket is damaged
Replace the accumulator assembly
Replace the output device controller PCA board

Remove EIO / network card (will be reset if not removed)

Perform NVRAM initialization by holding down the Reset button
for more than 20 seconds while power on the printer
If error persists replace the formatter board
HP 4, 4+, 4P 68 ERROR
Remove EIO / network card (will be reset if not removed)
Perform NVRAM initialization
If error persists replace the formatter board

Press the Select button to clear the error and continue printing
Remove disk (Flash or Hard disk)
Replace the hard disk
Replace the flash memory

HP LASER PRINTERS 5000, 5100 (ERROR 68 NVRAM ERROR

CHECK SETTINGS) and (ERROR 68 NVRAM FULL)
Print a configuration page and check the printer settings to
determine which values have changed
Hold down (Cancel Job) Button while turning the printer on
Replace formatter board

Print a configuration page

Perform a NVRAM initialization and re-enter the configuration
information
Replace the formatter board
HP 9000 ERROR 68.1 NVRAM OR HARD DISK IS FULL
Reseat the hard disk
Reinitialize the hard disk
Replace the hard disk
69 - DUPLEXER

HP LASER PRINTER 4200, 4300 ERROR 68.X PERMANENT

STORAGE

ALL (HP 2 to 5Si SERIES)

Print a configuration page and check the printer settings to

determine which values have changed
Perform an NVRAM initialization
Replace formatter board

Defective I/O - Formatter board

Defective formatter PCA

HP LASER PRINTER 4200, 4300 ERROR 68.0, 68.1

PERMANENT STORAGE FULL, PERMANENT STORAGE FULL

Temporary duplexer error

Reseat duplexer
Replace duplexer

Use HP Web jet admin software to delete files from hard disk
Reinitialize the hard disk
Replace the hard disk
Replace formatter board

HP 1200, 2200, 3100, 3150 FAX, 3200 FAX, 4100

HP 1100, 2100, 2300, 4000, 4050, 5000, 5100, 8000, 8100, 8150

Duplexer side adjust has failed

Turn the printer off and then on
Reseat the duplexer assembly
Replace the duplexer assembly

Strana 10

69 DUPLEXER (continued)

79 - CRITICAL HARDWARE ERROR (continued)

HP 4200, 4300

Try using parallel interface to test the formatter board

Remove network card, then perform a cold reset
If network cable is removed and error persists, replace the EIO
card or network card
Replace firmware DIMMs
Replace formatter board

HP COLOR 8500, 8550

HP LASER PRINTER 5000, 5100

Firmware has detected a hardware failure within the formatter

Replace the formatter board

HP 3200

Duplexer is not functioning

Reseat duplexer
Replace the duplexer assembly

(79.XX.YY)

HP 4500, 4550
Duplex mechanism failure
Duplex slide adjust has failed
Temporary error
HP 9000

Temporary duplexer error

Reseat duplexer
Perform a service test
Perform a paper path test
If error persists replace duplex unit

Temporary firmware error

Upgrade the formatter firmware or replace the firmware DIMM
with the latest version of the firmware
Replace firmware DIMM
Replace formatter

70, 71 - FAULTY MIO CARD OR SIMMs

ALL

HP 1100, 2100, 4000, 4050, 8000

Personality cartridge or SIMM installed in font or SIMM slot is

incompatible with the printer
Replace with compatible or SIMM

Turn printer off, then on

Remove network cable or parallel cable then power cycle the
printer
If error persists, remove network card
If error persists, replace formatter board, firmware chip, network
card

Faulty MIO card or cards

Replace MIO card or cards

(79.XX.YY)

HP 9000
Critical hardware error has occurred
Turn printer off, then on
Software error-print from different software
Replace or reseat interface cable
Try using parallel interface
Upgrade to latest firmware
Remove hard disk and turn printer off, then on
If error persists replace formatter board

HP 4100
Temporary communication error
Software error
Turn printer off, disconnect from network and turn printer back
on to isolate printer

HP 5Si

79 - CRITICAL HARDWARE ERROR (continued)

HP 4200, 4300

81 - DEFECTIVE NIC, OR FORMATTER BD. (continued)

The printer has detected an error with the network card

Reseat the network card
Turn printer off, then on
Put network card in a different slot
Replace network card

HP LASER PRINTER 4200, 4300

EIO accessory card in slot X has encountered a critical error

Reseat EIO / Network card
Replace EIO / Network card
Replace formatter board

HP LASER PRINTERS 9000

80 - DEFECTIVE NETWORK CARD, OR FORMATTER BOARD
ALL

Improper MIO connection

Replace the network cable
Defective MIO / Network card
Replace Network card
Replace the formatter board

HP 1200, 2200, 3100, 3150, 3200, 4100

Temporary printer error, disconnect the power cable from the
product, wait at lest 30 seconds, reconnect the power cable,
and then wait for the product to initialize
If error persists replace formatter board

Temporary error has occurred while testing the printer

Turn printer off, then on
If error persists replace the formatter board
89 - POSTSCRIPT ROM FAILURE
ALL HP LASER PRINTERS

Bent or broken pins on postscript ROMs

Improperly located ROMs or SIMMs
Temporary error, turn printer off, then on
Defective postscript ROMs or SIMMs

99 - FIRMWARE UPGRADE
HP 9000

72 - DEFECTIVE FONT CARTRIDGE OR FORMATTER BOARD

ALL

Font cartridge removed during formatter access

Defective font cartridge
Replace font cartridge
Defective formatter board
Replace formatter board

79 - CRITICAL HARDWARE ERROR

ALL
Software/ drivers, Memory, Font-MACRO-Personality cartridge,
Optional I/O cards or Bad network card
Defective formatter board
Replace formatter board
Replace the I/O card or the Network card

Turn printer off, then on

Reseat formatter and firmware DIMM
Upgrade firmware on formatter board and network card
Replace firmware DIMM
Replace formatter board

Turn printer off, then on

Try printing from different software
Replace the network cable and cycle power
Remove network card and cycle power
Remove DIMMs one at a time and cycle power
Upgrade firmware DIMM or replace the firmware DIMM
Try using parallel interface to test the formatter board
With network removed, perform a cold reset
Remove the hard disk and cycle power
If network cable is removed change the network card, formatter
board, firmware chip

HP COLOR LASER PRINTER 4500, 4550

Temporary error
Software error
Replace firmware DIMM
Replace jet direct card
Replace formatter board

79.XX.YY ERROR

HP COLOR 4600, 5500

Turn printer off then on

Try printing a job from a different software program
Replace network cable and cycle power
Remove network card and cycle power
Remove DIMMs one at a time and cycle power

EIO error
Replace jet direct / EIO card

Firmware flash failure

Download and install firmware flash upgrade
Replace the flash Firmware DIMM

HP 8500
HP5000, 51000, 5Si, 8100, 8150

HP 4, 4+, 5
Defective toner cartridge
Replace toner cartridge
Software communications error between network and printer
Replace network card
Replace formatter board

HP 4500

A critical hardware error has occurred

Turn printer off, then on
Reseat formatter and the DIMMs
Replace DIMMs
Replace the formatter board

Memory card error

HP 9000
Temporary network card error
Reseat network card in a different EIO slot
Replace the network card
81 - DEFECTIVE NETWORK CARD, OR FORMATTER BOARD
ALL
Unplug network cable or parallel cable from the printer and then
turn it off and then on, if error went away then it was a bad
communication from the network or the computer
If error persists while printer is disconnected from the network
or computer, replace the following:
Replace EIO / network card
Replace formatter bard
HP LASER PRINTERS 1200, 2200, 3100, 3150, 4100
Temporary printer error, disconnect the power cable from the
product, wait at lest 30 seconds, reconnect the power cable,
and then wait for the product to initialize
If error persists replace the formatter board

Strana 11

Maintenance Message Resets:

HP 8000/ 8100/ 8150 Printers:

HP Color LaserJet 8500/ 8550 Printers (FUSER KIT RESET):

HP Test Page / Config Page Procedures:

To clear the Maintenance Service Message from the LCD display:

HP 3Si:

1.

1.

HP 2, 3, 3Si

1.
2.
3.
4.
5.

Press ONLINE until the light goes off

Hold down MENU until PCL CONFIG MENU appears
Press the MENU key until SERVICE MSG=ON* appears
Press the + or - key to change display to SERVICE
MSG=OFF
Press ENTER/RESET MENU key to turn message off, the *
should appear, then press ONLINE

HP 4Si:
1.
2.
3.
4.
5.

Press ONLINE until the light goes off

Press MENU until CONFIG MENU appears
Press the ITEM key until SERVICE MSG=ON* appears
Press the + or - key to change display to SERVICE
MSG=OFF
Press the ENTER key to turn message off, the * should
appear, then press ONLINE

2.
3.
4.
5.
6.

HP 9000 Printers:
1.
2.
3.
4.
5.

HP 5Si:
1.
1.
1.
1.

Press MENU key 4 times for CONFIG MENU

Press ITEM to display SERVICE MESSAGE=OFF
Press ENTER
Press ONLINE

Turn the printer off

Press and hold the CHECK key
Power on the printer
Release the CHECK key after all three lights come on The
display should read SELECT LANGUAGE
Press the up arrow until MAINTENANCE KIT is displayed,
then press the CHECK key again and the maintenance kit
count has been reset

HP Color LaserJet 4500/ 4550 Printers (TRANSFER KIT

RESET):
1.

HP 4000/ 4050/ 4100/ 5000/ 5100:

2.

1.
2.

3.

Turn the printer off

Hold down the left side of the ITEM and VALUE +/- keys,
turn the printer on and wait until RESET MAINTENANCE
COUNT is displayed and then release the keys

Press the MENU button until the display reads

CONFIGURATION MENU
Press the ITEM button until the display reads SERVICE
MESSAGE = ON/OFF
Select OFF*
Press SELECT to save
Turn printer off
Hold the VALUE MINUS and ITEM MINUS buttons while
turning the printer back on Hold buttons down until display
reads RESET MAINT/COUNT and then release both buttons

Press the MENU button until the RESETS MENU is

displayed
Press the ITEM button until TRANSFER KIT SELECT IF
DONE is displayed
Press the SELECT button

2.
3.
4.

Press the MENU button until the RESETS MENU is

displayed
Press the ITEM button until RESET FUSER LIFE COUNT is
displayed
Press the SELECT button to reset
Press the GO button to return to READY

1.
2.
3.

Take printer off line

Press TEST button for 5 seconds (05 SELF TEST will
appear on LCD)
Wait for test page to print

HP 2P, 2P+, 3P
1.
2.
3.

Take printer off line

Press ALT and TEST button simultaneously (05 SELF
TEST will appear on LCD)
Wait for test page to print

HP 4, 4+, 5, 4P, 4V, 4Si, 5Si

1.
2.
3.
4.
5.

Take printer off line

Press MENU button to scroll through menu until TEST
MENU appears on display
Press ITEM until SELF TEST appears on display
Press ENTER
Wait for test page to print

HP 4000, 4050, 4100, 5000, 5100, 8000, 8050, 8100, 8150, CLJ
4500, CLJ 4550, CLJ 8500, CLJ 8550
1.
2.
3.

Take printer off line

Press MENU button to scroll through menu until
INFORMATION MENU appears on display
Press ITEM until PRINT CONFIGURATION or PRINT
CONFIG PAGE appears on display
Press SELECT
Wait for test page to print

HP Color LaserJet 4500/ 4550 Printers

1.
(FUSER KIT RESET):

4.
5.

HP 4200/ 4300:

1.

HP 2300, 4200, 4300, 9000, CLJ 4600, CLJ 5500, CLJ 9500

1.
2.

2.

3.
4.

Turn The Printer off

Hold down the SELECT button, and then turn on the printer.
Continue holding the SELECT buton until all three printer
control-panel lights flash once and then remain on (may take
up to 10 seconds)
Press the UP ARROW button to scroll to NEW
MAINTENANCE KIT
Press the SELECT button to reset the maintenance-kit
counter

HP 4500/ 4550:
1.
2.

3.
4.
5.
6.
7.
8.

Turn the printer off

Hold down the CANCEL JOB and SELECT keys and turn
the printer on, then wait until the display goes blank and the
three LED's come on
Press the right side of the MENU key, then press the
SELECT key
You will enter SERVICE MODE after the normal test
completes
Press the ITEM key until the FUSER MAINTENANCE
COUNT appears
Press VALUE +/- to change to zero
Press SELECT to save
Press GO; the printer should return to READY

3.
4.

Press the MENU button until the RESETS MENU is

displayed
Press the ITEM button until FUSER KIT SELECT IF DONE
is displayed
Press the SELECT button
Press the GO button to return to READY

1.
2.
3.
4.

Press 3 button to enter menus

Press UP or DOWN button to go to INFORMATION
Press 3 button to select
Press UP or DOWN button to go to PRINT
CONFIGURATION
Press 3 button to select
Wait for test

HP Color LaserJet 4600 Printer

5.
(IMAGE TRANSFER KIT (ETB) RESET):

5.
6.

1.

HP 4L, 1100

2.

After Maintenance is performed, the display should read

NEW TRANSFER KIT =
Press the down arrow to highlight YES, then press the 3
button to reset Or enter CONFIGURE DEVICE in menus,
choose RESETS then RESET SUPPLIES, choose NEW
TRANSFER KIT and select

HP Color LaserJet 4600 Printer (FUSER KIT RESET):

1.
2.

After Maintenance is performed, the display should read

NEW FUSER KIT =
Press the down arrow to highlight YES, then press the 3
button to reset Or enter CONFIGURE DEVICE in menus,
choose RESETS then RESET SUPPLIES, choose NEW
FUSER KIT and select

1.
2.

Press GO button, then release

Wait for test page to print

HP 5L, 6L, 5P, 6P, 1150, 1200, 1300, 2100, 2200, CLJ 1500,
CLJ 2500
1.
2.

Press GO and JOB CANCEL buttons simultaneously,

then release
Wait for test page to print

HP Color LaserJet 8500/ 8550 Printers (TRANSFER KIT

RESET):
1.
2.
3.

Press the MENU button until the RESETS MENU is

displayed
Press the ITEM button until RESET TRANSFER LIFE
COUNT is displayed
Press the SELECT button to reset, then GO to return to
READY

Strana 12