Scribd
Upload
96 views

U-1 2938

This document summarizes the key details of a pressure vessel as required by the ASME Boiler and Pressure Vessel Code for certification. It includes information about the manufacturer, purchaser, installation location, vessel type and dimensions, materials used, design pressures, inspection and testing results, and certificates of compliance signed by the manufacturer and inspectors.

Uploaded by

Waqas Waqas
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
96 views

U-1 2938

This document summarizes the key details of a pressure vessel as required by the ASME Boiler and Pressure Vessel Code for certification. It includes information about the manufacturer, purchaser, installation location, vessel type and dimensions, materials used, design pressures, inspection and testing results, and certificates of compliance signed by the manufacturer and inspectors.

Uploaded by

Waqas Waqas
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

FORM U-1 MANUFACTURERS DATA REPORT FOR PRESSURE VESSELS

As Required by the Provisions of the ASME Boiler and Pressure Vessel Code Rules, Section VIII, Division 1
1. Manufactured and certified by
(Name and address of Manufacturer)

2. Manufactured for
(Name and address of Purchaser)

3. Location of installation
(Name and address)

4. Type
(Horizontal, vertical, or sphere)

(Tank, separator, jkt. vessel, heat exch., etc.)


(Drawing number)

(CRN)

(Manufacturers serial number)


(Year built)

(National Board number)

5. ASME Code, Section VIII, Div. 1


[Edition and Addenda, if applicable (date)]

(Code Case number)

[Special service per UG-120(d)]

Items 611 incl. to be completed for single wall vessels, jackets of jacketed vessels, shell of heat exchangers, or chamber of multichamber vessels.
6. Shell:

(a) Number of course(s)

(b) Overall length

Course(s)
No.

Diameter

Material
Length

7. Heads: (a)

Thickness

Spec./Grade or Type

Nom.

Corr.

Long. Joint (Cat. A)


Type

Full, Spot, None

(b)

(Material spec. number, grade or type) (H.T. time and temp.)

Location (Top,
Bottom, Ends)

Thickness
Min.

Corr.

Radius
Crown

Elliptical
Ratio

Knuckle

Conical
Apex Angle

Eff.

Circum. Joint (Cat. A, B & C)

Heat Treatment

Type

Temp.

Full, Spot, None

Eff.

Time

(Material spec. number, grade or type) (H.T. time and temp.)

Hemispherical
Radius

Flat
Diameter

Side to Pressure
Convex

Concave

Category A
Type

Full, Spot, None

Eff.

(a)
(b)
If removable, bolts used (describe other fastening)
(Material spec. number, grade, size, number)

8. Type of jacket

Jacket closure
(Describe as ogee and weld, bar, etc.)

If bar, give dimensions

If bolted, describe or sketch.

9. MAWP

at max. temp.
(Internal)

Min. design metal temp.

(External)

10. Impact test

(Internal)

at

(External)

at test temperature of

[Indicate yes or no and the component(s) impact tested]

11. Hydro., pneu., or comb. test pressure

Proof test

Items 12 and 13 to be completed for tube sections.


12. Tubesheet

[Stationary (material spec. no.)]

[Diameter (subject to press.)]

[Floating (material spec. no.)]

(Diameter)

(Corr. allow.)

(Nominal thickness)
(Nominal thickness)

[Attachment (welded or bolted)]

(Corr. allow.)

(Attachment)

13. Tubes
(Material spec. no., grade or type)

(O.D.)

(Nominal thickness)

(Number)

[Type (straight or U)]

Items 1418 incl. to be completed for inner chambers of jacketed vessels or channels of heat exchangers.
14. Shell: (a) No. of course(s)

(b) Overall length

Course(s)
No.

Diameter

Material
Length

Thickness

Spec./Grade or Type

Nom.

Corr.

Long. Joint (Cat. A)


Type

15. Heads: (a)

Full, Spot, None

Circum. Joint (Cat. A, B & C)

Heat Treatment

Type

Temp.

Full, Spot, None

Time

Thickness
Min.

Corr.

Radius
Crown

Knuckle

Elliptical
Ratio

Conical
Apex Angle

(Material spec. number, grade or type) (H.T. time and temp.)

Hemispherical
Radius

Flat
Diameter

Side to Pressure
Convex

Concave

(a)
(b)
If removable, bolts used (describe other fastening)
(Material spec. number, grade, size, number)

(07/10)

Eff.

(b)
(Material spec. number, grade or type) (H.T. time and temp.)

Location (Top,
Bottom, Ends)

Eff.

Category A
Type

Full, Spot, None

Eff.

FORM U-1 (Back)


16. MAWP

at max. temp.
(Internal)

Min. design metal temp.

(External)

(Internal)

at

(External)

at test temperature of

17. Impact test

[Indicate yes or no and the component(s) impact tested]

18. Hydro., pneu., or comb. test pressure

Proof test

19. Nozzles, inspection, and safety valve openings:


Purpose
(Inlet, Outlet, Drain, etc.)

20. Supports: Skirt

Material

Diameter
or Size

No.

Type

Lugs
(Yes or no)

Nozzle

Legs
(Number)

Nozzle Thickness

Flange

Nom.

Reinforcement
Material

Corr.

Others

Attachment Details
Nozzle

Flange

Location
(Insp. Open.)

Attached

(Number)

(Describe)

(Where and how)

21. Manufacturers Partial Data Reports properly identified and signed by Commissioned Inspectors have been furnished for the following items of
the report (list the name of part, item number, Manufacturers name, and identifying number):

22. Remarks

CERTIFICATE OF SHOP COMPLIANCE


We certify that the statements in this report are correct and that all details of design, material, construction, and workmanship of this vessel
conform to the ASME BOILER AND PRESSURE VESSEL CODE, Section VIII, Division 1.
U Certificate of Authorization Number
Date

Expires

Name

Signed
(Manufacturer)

(Representative)

CERTIFICATE OF SHOP INSPECTION


I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and/or the State or Province
of

and employed by

of

have inspected the pressure vessel described in this Manufacturers Data Report on

, and

state that, to the best of my knowledge and belief, the Manufacturer has constructed this pressure vessel in accordance with ASME BOILER AND
PRESSURE VESSEL CODE, Section VIII, Division 1. By signing this certificate neither the Inspector nor his/her employer makes any warranty, expressed
or implied, concerning the pressure vessel described in this Manufacturer's Data Report. Furthermore, neither the Inspector nor his/her employer shall
be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.
Date

Signed

Commissions
(Authorized Inspector)

[National Board (incl. endorsements), State, Province, and number]

CERTIFICATE OF FIELD ASSEMBLY COMPLIANCE


We certify that the statements in this report are correct and that the field assembly construction of all parts of this vessel conforms with the requirements
of ASME BOILER AND PRESSURE VESSEL CODE, Section VIII, Division 1. U Certificate of Authorization Number
Date

Name

Expires

Signed
(Assembler)

(Representative)

CERTIFICATE OF FIELD ASSEMBLY INSPECTION


I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and/or the State or Province
of

and employed by

of

, have compared the statements in this Manufacturers Data Report with the described pressure vessel

and state that parts referred to as data items

, not included in the certificate of shop inspection, have been

inspected by me and to the best of my knowledge and belief, the Manufacturer has constructed and assembled this pressure vessel in accordance
with the ASME BOILER AND PRESSURE VESSEL CODE, Section VIII, Division 1. The described vessel was inspected and subjected to a hydrostatic test of

. By signing this certificate neither the Inspector nor his/her employer makes any warranty, expressed or

implied, concerning the pressure vessel described in this Manufacturer's Data Report. Furthermore, neither the Inspector nor his/her employer
shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.
Date

Signed

Commissions
(Authorized Inspector)

(07/10)

[National Board (incl. endorsements), State, Province, and number]

You might also like