DIGITAL EMPR

Meta-MEC Series

Digital Motor Protection Relay

Digital
Motor Protection Relay
General digital type motor protection relays using MCU(Micro Controller Unit)
-Real time processing and high precision
Multiple protection
Protection
Wiring
Over current
Under current
Stsll
Lock
Phase failure
Revers phase
Asymmetry
Grount fault

-S
DMP

-SZ
DMP

Screw type

-SI
DMP

Short circuit

Install the Unit /Extension type in one body

The display part may be seperated from the body
You can check the values and the causes of the
fauit without opening the distrioution panel door

Fig. (D-EMPR in the MCC unit)

Both screw type and tunnel type
wirings are available in a DMP-E
Type D-EMPR
Simply detach the screw terminal, you can use it by
the tunnel type reiay

Standard: IEC60947-1, IEC60947-4-1, IEC60947-5-1,

UL508, KSC4504

Certification & approval: CE, UL, cUL, Lloyd register,

Korea legister, KS, ISO 14001,
ISO 9001(Including proceedings)

-T
DMP

-TZ
DMP

-T
DMP

Tunnel type

M e t a - M E C

S E R I E S

Display the causes of the fault and the values

Prompt A/S by looking the LED panel which
displays the causes of the fauit and the values
3phase digital ampere-meter function
(Digital ampere-meter)
Additional ampere-meter is not needed
Motor load rate(%)
Easy to check the motor
load condition
R phase current value

S phase current value

T phase current value

Selectable either the inverse time or definite time

characteristics

Inverse time characteristics

Defiinite time characteristics

Applicable to inverter contol circuit

LG DMPR has high performance under the
harmonic noise and can be used in the
Inverter control circuit (20~200Hz)

Elegant design
High class product image
by the elegant design

Specifications of D-EMPR
Digital E M P R

DMP-S

Model No.
Wiring
Panel mount
Operation time
Protection
Over current
Phase failure
Reverse phase
Asymmetry
Stall
Lock
Under current
Ground fault
Short circuit (Note2)
Alarm
Current setting range (A)
Motor capacity
220~240V
(kW)
380~440V
Time setting Definate Delay in starting
range (sec) time
Delay in operating
Inverse time
Reset
Tolerance
Current
Time
Operating power (Note3)
Voltage
Frequency
Aux. contact OL
2-SPST
AL
SPST
Insulation resistance
Surge impulse voltage(IEC1000-4-5)
Fast transient burst(IEC1000-4-4)
Environment Temperature Operation
Storage
Humidity
Display
7-Segment
Bar-Graph
Mounting type

DMP-T

DMP06-S

DMP60-S
Screw type

DMP06-T

DMP60-T
Tunnel type

Unit or Extension(Note1)
Select either reverse time characteristics or definate time characteristics
According to the setting time
3 sec.
Within 0.1 sec.
5 sec.
5 sec.
Within 0.5 sec.
3 sec.
Within 0.05~1 sec. Selectable (0.05~1.0sec)
Within 50ms
Variable (60~110% of the setting current)
0.5~6
5~60
0.5~6
0.09~0.75
1.1~11
0.09~0.75
0.12~1.5
2.2~22
0.09~1.5
0~60sec
0~30sec
0~60sec
Manual reset
5%
5% (or0.5sec)
AC 190~250V
60Hz (50Hz)
3A/250Vac Resistive load
3A/250Vac Resistive load
Over DC 500V 100
1.250 6kV (Apply standard wave form)
2.5kV/5min
-25~70
-30~80
30~90% RH (No freezing)
3 phase current, cause of a fault
60~110% of real load current
35mm Din-rail/Panel

5~60
1.1~11
2.2~22

Note1) In extension type, the digital EMPR is calibrated with combining the display past and mainbody so, please cautious not to
combine the display part and main body with different part No.
Note2) Instantaneous short circuit protection is optional
Note3) Operational voltage of AC 110V and 50Hz is optional

Setting

M e t a - M E C

S E R I E S

Digital E M P R

Before operating a motor, set the D-EMPR as follows

1. C h e c k t h e o p e r a t i o n o f t h e T e s t / R e s e t b u t t o n
Check the operation when it is tripped
1) Check the wiring method (Refer to P13~14)
2) Press the Test/Reset button and then test is
displayed on the LED and the DMPR is tripped
3) Press the Test/Reset button again and then
it is reset
Note) In order to avoid the trip fault, the push
operation of Test/Reset is not avaiable
when a motor is rotating

R phase

Digital display
Bar graph

S phase
T phase

Display button
Test/Reset button

FUNC button

Sel button

Current knob

Time knob

2. Shift the mode by pressing the FUNC key and then select the values by press the Sel key
You can finish the setting by pressing the Sel key in the Sto mode
To protect the operation under the motor rotating, setting is allowed only in the test mode
FUNC

Sel

Functions

Note

Inverse or definite time

characteristics

Default is inverse time

characteristics

Set the O-time

(Definite time only)

For D-time setting,

use the time knod

Reverse phasse protection

Default is Off

Under current protection

Default is OffNote1)

Alarm function
(With pre-alarm function)

Default is Off

Ground fault and

Setting the operating time

Default is Off
(Z type)

Stall function

Default is Off

Lock function

Default is Off

CT ratio

Default is 1:1

Phase failure

Default is On
to store

Store

Push the SEL button

to store

Note2)

Note1) Set the under current value from above 350mA

Note2) Do not change the CT ratio in 60 type (Dafault is 10:1)

1) First shift to the test mode by press the Test/Resetbutton and then set the functions
by press the FUNCbutton
2) Each time you press the FUNCbutton, the function mode switches from 1.CHA mode to Sto mode.
When the mode that you want to change is displayed, push the Selbutton to select the value you want.
After you select the value, press the FUNCbutton to finish the settings and it displays the next mode
3) If no button is pressed in the selection mode, it remains in that mode
4) If you select the inverse time characteristics it skips the mode 2 (Definite O-time) and go to the
mode 3 (Reverse phase)

Setting
Digital E M P R

Alarm signal (Alert function)

5) 5. Alt is the alert setting mode. It displays the load rate
of the current setting value by the bar LED (60~110%)
- If the current is higher than the setting value, the bar
LED is swieched on and off and the AL relay(07-08) make
close and open in 1sec interval unitl the EMPR is tripped
(Pre-alarm function)
- If the 5. Alt mode is set to off, the AL relay make close
after the EMPR is tripped (Normal open contact)
6) To finish the settings you have to press the Selbutton
in the Sto mode

5.A Lt
On

AL(07-08) contact operation

1
0

1
0

Off
Normal

Alarm

Alert setting
value

Trip

Trip setting
value

3. Adjust the operating time by the time knod

Inverse time characteristics

1) Select the inverse time in the 1. CHA mode, the default operating time is 600% of the rated current
2) The setting range of the operating time is 0~60sec. Set the time by considering the motor start time
3) When it is over the setting time, the EMPR operate in accord with the hot curve
Definite time characteristics
1) Select the definite in the 1. CHA mode, it is operated by the definite time characteristics
2) D-time means the time that delays the operating time when the motor is starting
3) The setting range of the operating time is 0~60sec. Set the time by considering the motor start time
4) Set the O-time at the setting mode 2. dEF and the range is 0~30sec

4. Adjust the operating current by the current knob

1) Set the operating current based on the rated current that is discribed in the name plate.
Gennerally set the 110~115% of the real load current in the normal load condition
2) There ara 2 CT types according to the current range (0.6 / 60). When you use the external CT you can see
the real current by set the CT ratio (In 60CT type the defaut CT ration is 10:1)
3) You can easily set the current value by refer to the load rate which is displayed on the bar-graph
(Approx. 90% load rate)

M e t a - M E C

S E R I E S

5. Check the setting state by the display key

1) In normal condition it display the maximum
current among the three phase current
2) Each time you press theDisplaybutton
you can see the current and values as PIG X
3) If no button is pressed for 3~4 seconds. it
returned to the normal condition

R phase current

Set the O-time to 10sec

S phase current

(Display only in definite time)

Normal condition

T phase current

Set the D-time to 10sec

(Set the motor starting time)

5A setting

6. Check the causes of the fault by look at the display unit (7-segment)
The causes of the fault is switched on and off for 0.5sec interval. If you press theDisplaybutton at this time,
display you can see the values and the causes of the fault

Overload

Turn on

ex)
Turn
on& off

Under current

Phase fail

Stall

Lock

Reverse phase

Ground fault

Short circuit

Dimensions
Digital E M P R

Type

Mounting dimensions

Dimensions
0.7kg
Aux. contact wire size
:below 8mm2
Torque : 0.5N

DMP-S
DMP-SZ

0.64kg

DMP-S
DMP-SZ
&
Extension
cable
Panel mounting

Panel cutting size

M e t a - M E C

Type

S E R I E S

Mounting dimensions

Dimensions
0.56kg
Wire size to penetrate a CT
:below 22mm2

DMP-T
DMP-TZ

0.5kg

DMP-T
DMP-TZ
&
Extension
cable
Panel mounting

Panel cutting size

Note1) In extension type, the digital EMPR is calibrated with combining the display unit and mainbody
so, pleose cauyious not to combine the display unit and mainbody with different part No.
Note2)The 07-08 contacts ara the ZCT input terminal (Digital EMPR with ground fault function)

DMP-S/T
Digital E M P R

DMP- S/ T
Over-current/Under current/Phase failure/Asymmetry
Stall/Lock/Instantaneous short circuit protection
Unit type or extension type is available
- Extension type:Remotely mounts the display unit
on the panel surface
3 phase ampere meter function:Check the 3 phase
current and setting value by press the display button
Select the inverse time or definite time
Easy to operate:Set the most function by the operation
button and knod
Display the causes of the fault and the values
Alarm setting:Load ratio is displayed up to setting current

Protect function
Over current
Depend on setting time
Selectable the inverse/definite
Phase loss
Within 3seconds
Over 70% of the rate of unbalance
Phase unbalance
Within 5seconds
Over 50% of the rate of unbalance
Phase reverse
Within 0.1seconds
Function enable
Stall
Within 5seconds
Over 180% of the setting current
Lock
Within 0.5seconds
Setting 200~900% of rated current
Under current
Within 3seconds
Setting 30~70% of rated current
Lock protection is operated after setting D-time in case of definite time type

Function selection
FUNC
1. CHA
2. dEF
3. r.P
4. Und
5 . A lt
6. S t l
7. Loc
8. Ct
9. P.F
Sto

Sel
Inv/dEF
0~30(S)
oFF/on
oFF/30~70(%)
oFF/60~110(%)
oFF/on
oFF/200~900(%)
1~120
on/oFF
Sto

Description
Operating characteristics setting(Inverse/definite time type)
Setting the operating time(In definite type)
Phase reverse enable
Under current enable and setting
Alerting enable and setting
Stall enable
Lock enable and setting
CT ratio setting
Phase fault enable
Store

2.dEF is only displayed when dEF is selected in a 1.CHA mode

Ratings
Model
Type

10

Wiring method
Panel mount

Operating characteristics
Alerting function
Current range(A)
DMP06-
DMP60-
Setting time
Definite Delay(D-T)
Operating(O-T)
Inverse
Reset type
Operating voltage
Voltage
Frequency
Aux. contacts
OL
2-SPST(95~98)
AL
SPST(07-08)
Indicate
7-segment
Bar-LED arrys
Mounting

D M P -S
Screw

D M P -T
Tunnel

Unit or Extension
Inverse/definite type
Variable between 60 and 110%
0.5~6
5~60
0~60seconds
0~30seconds
0~60seconds
Manual reset
AC 190~250V
60Hz (50Hz)
3A/250Vac resistive load
3A/250Vac resistive load
3-phase current value, fault cause
Load ratio (60~110%)
35mm Din-rail/Panel

M e t a - M E C

Wiring method

S E R I E S

1 Phase motor

Note1)

Operational
power

External CT combination

Note1) Please turn off the reverse phase function when it is used for 1 phase motor

11

DMP-SZ/TZ
Digital E M P R

DMP-SZ/ TZ
Over-current/Under current/Phase failure/Asymmetry
Stall/Lock/Ground-fault
Unit type or extension type is available
- Extension type:Remotely mounts the display unit
on the panel surface
3 phase ampere meter function:Check the 3 phase
current and setting value by press the display button
Select the inverse time or definite time
Easy to operate:Set the most function by the operation
button and knod
Display the causes of the fault and the values
Ground fault protect function is added

Protect function
Over current
Phase loss
Phase unbalance
Phase reverse
Stall
Lock
Under current
G r o u n d f a u l t (Note1)

Depend on setting time

Selectable the inverse/definite
Within 3seconds
Over 70% of the rate of unbalance
Within 5seconds
Over 50% of the rate of unbalance
Within 0.1seconds
Function enable
Within 5seconds
Over 180% of the setting current
Within 0.5seconds
Setting 200~900% of rated current
Within 3seconds
Setting 30~70% of rated current
Selectable
Grounded current setting by dip s/w
0.05~1.0seconds
(100~2500mA)
Lock protection is operated after setting D-time in case of definite time type

Function selection
FUNC
1. CHA
2. dEF
3. r.P
4. Und
5. g-F
6. S t l
7. Loc
8. Ct
9. P.F
Sto

Sel
Inv/dEF
0~30(S)
oFF/on
oFF/30~70(%)
oFF/0.05~1.0(S)
oFF/on
oFF/200~900(%)
1~120
on/oFF
Sto

Description
Operating characteristics setting(Inverse/definite time type)
Setting the operating time(In definite type)
Phase reverse enable
Under current enable and setting
Ground fault enable and setting
Stall enable
Lock enable and setting
CT ratio setting
Phase fault enable
Store

2.dEF is only displayed when dEF is selected in a 1.CHA mode

Ground fault sensitive current selection : Refer to page 15

2.dEF : Refer to page 10

Ratings
Model
Type
Operating characteristics
Alerting function
Current range(A)
Setting time

Operating voltage

Aux. contacts(2a, 2b, 1a1b)

Indicate
12

Mounting

Wiring method
Panel mount

DMP06-
DMP60-
Definite Delay(D-T)
Operating(O-T)
Inverse
Reset type
voltage
Frequency
ZCT input (07-08)
OL, GR
2-SPST(95~98)
7-segment
Bar-LED arrays

DMP -SZ
Screw

DMP -TZ
Tunnel

Unit or Extension
Inverse/definite type
Variable between 60 and 110%
0.5~6
5~60
0~60seconds
0~30seconds
0~60seconds
Manual reset
AC 190~250V
60Hz (50Hz)
200mA/110mV(ZCT)30, 50, 65, 80
3A/250Vac resistive load
3-phase current value, fault cause
Load ratio (60~110%)
35mm Din-rail/Panel

M e t a - M E C

S E R I E S

Wiring method

External CT combination

13

Characteristics curve
Digital E M P R

Characteristics curve

Definite time characteristics

14

Ordering

M e t a - M E C

S E R I E S

Digital E M P R

DMP06 - SZ 220

Current setting range

Option

Wiring method

Operational power

06

0.5~6A

Screw

- Standard

220

AC220V

60

5~60A

Tunnel

Z Ground fault

110

AC110V

The standard length of a extension cable is 1.5m,

2m, 4m cable is optional
For ground fault protection, ZCT (30,50,65,80)made by
LG is optionally required
1) Detach the screw terminal

2) Select the ground fault sensitive current

Remove the 3 screws either in the line side or

the load side and pull out the bus bar.
If you remove the screw terminal, you can
use it as a tunnel type digital EMPR,
assemble it to the opposite sequence

Dip s/w

Sensitive current
(mA)

100

200

500

1000

1500

2000

2500

Note) High sensitive current(30~300mA)

is optional

ZCT( Zero-phase Sequence Current Transformer)

Ratings
ZCT,
ZCT,
ZCT,
ZCT,

Type
D30, DMP-Z
D50, DMP-Z
D65, DMP-Z
D80, DMP-Z

Diameter(A)
30
50
65
80

Ratio
200mA/100mV

Weight(kg)
0.5
0.7
0.9
1.5

Model
LZT-030
LZT-050
LZT-065
LZT-080

Dimension

Unit (m/m)

Model

LZT-030

30

25

LZT-050

50

25

LZT-065

65

LZT-080

80

108 100 114

32

32

131 100 122

32

36

26

143 114 133

39

37

34

174 160 180

40

40

15

2003-09

Safety Instructions
For your safety, please read users manual thoroughly before operating.
Contact the nearest authorized service facility for examination, repair,
or adjustment.
Please contact qualified service technician when you need maintenance.
Do not disassemble or repair by yourself!
Any maintenance and inspection shall be performed by the personnel having
expertise concerned.

[email protected]

LG Industrial Trading (Shanghai) Co., Ltd

China

Address: Room1705-1707, 17th Floor Xinda

Commerical Building No 318, Xian Xia Road Shanahai
Tel: 86-21-6252-4291
Fax: 86-21-6278-4372
e-mail: [email protected]

Room 303, 3F

LG Industrial Systems Shanghai Office

China

Address: Room1705-1707, 17th Floor Xinda Commerical Building

No 318, Xian Xia Road Shanahai, China
Tel: 86-21-6278-4370
Fax: 86-21-6278-4301
[email protected]

LG Industrial Systems Guangzhou Office

China

Address: Room 303, 3F, Zheng Sheng Building, No 5-6, Tian He

Bei Road, Guangzhou, China
Tel: 86-20-8755-3410
Fax: 86-20-8755-3408

[email protected]

Specifications in this catalog are subject to change without notice due to

continuous product development and improvement.

DMPR 2002.10 / (02) 2003.09 Printed in Korea STAFF