3.0 .

Hardware Installation & Initial Setup

3.1 RS-232 ConfigurationDB9 Male
DB9Male

Signal

I/O

PIN2

RXD

IN

PIN3

TXD

OUT

PIN5

GND

PIN7

RTS

OUT

PIN8

CTS

IN

Model XS1000
TCP/IP to RS232/422/485 Device Server
Users Manual

RS-422 Connection

3.2 RS-422/485 Configurationterminal header

Terminal
No

1.0 Introduction

RS-422

T+

T-

R+

R-

VIN

GND

The XS1000 is a cost effective and highly integrated

RS-485

485+

485-

VIN

GND

Serial-to-Ethernet 10/100Mbps device server. Embedding a

8051CPU with 64KB OTP ROM and 32KB SRAM. The serial

3.3 Connecting to 10/100M

interface supports handshake signals RTS and CTS. The

Use a standard Ethernet cable to connect the XS1000 to an

XS1000 can access 1 x RS232/422/485 devices located

Ethernet switch, or use a cross-over cable if you connect it

virtually anywhere (via Ethernet or Internet).

directly to a PC.

RS-485 Connection

The XS1000 automatically finds devices in the network and can

be configured by the serial Port, Telnet or WEB Browser.

3.4 Power Supply

XS1000 needs a 9 to 24VDC 1000mA power supply.

2.0 Features:
3-in-1 RS-232/422/485 interface Max.230Kbps Serial
interface and 10/100 Mbps Ethernet.
Supports 4- and 2-wire RS-485 with AUTO-SEND and
built-in terminator.
Power supply: 24 VDC and optional Power over Serial.
Terminal block for easy RS-422/485 serial wiring
Supports IP configuration by MAC address.

3.5 XS1000 LED indication

LINK:

Ethernet Link established.

ACT:

Data flow TX/RX.

PWR:

Power ON.

3.6 Connection Diagram

RS-232 Connection

Supports Driver, TCP Server/Client, UDP Server/Client and

Pair Connection protocols.

Easy and powerful configuration management.

4.0 Configuration and Operation

Approvals: CE, RoHS.

A. Assign a static IP address to your computer in the

192.168.2.2 to 192.168.2.254 range. Subnet mask

255.255.255.0. This is necessary to ensure that your
computer can communicate with your XS1000. Your
computer must have an Ethernet card and TCP/IP installed.
TCP/IP should already be installed on computer using
Windows 98/2000/XP and later operating systems.
B. The default IP address of the XS1000 is 192.168.2.1.
Open your web browser and enter this IP address to connect
to the XS1000.
C. Default user name is admin and the password is system.
Click OK. The setup screen will then appear, and you can

Static (or Fixed) IP

now configure the settings.

IP Address: default 192.168.2.1

D. Create a new COM port using VCOM.exe.

Menus explained:

Subnet mask: default 255.255.255.0

4.3 Administrator Setup

Gateway: default 192.168.2.254

Main admin window.

Primary DNS: default 192.168.2.253

4.4 Authentication

If you are connecting through a static or fixed IP from your

The user can change the username and password to prevent

network environment, perform these steps

unauthorized access.

Step 1: Enter IP address

Login ID and password authentication, the maximum number of

Step 2: Enter Subnet mask

characters is 15, (characters and numbers).

Step 3: Enter Gateway IP address

User Name: default admin

Step 4: Enter Primary DNS IP address

Password: default system

Step 5: click Update button

4.6 DHCP

Host Name (Optional): default NETUART, maximum

length 15 characters.
If there is a DHCP Server existing in your network
environment, you can set the IP configuration to DHCP to
get a dynamic IP address. The Host Name is an optional
item, depending on your DHCP Server setting.
4.5 System IP

4.2 The menu features as below:

The XS1000 support two IP connection types: Static IP and

5.0 System Status

DHCP. These types are listed in the Web page for the IP

This screen shows the XS1000s current status. All of the

Configuration settings. Each setup screen and available

information provided is read-only.

features will differ depending on what kind of IP connection

Kernel Version: the installed version of the kernel.

types you select. Default is Static IP

MAC Address: The present device MAC Address.

Nickname: the products NetUART model name.

Client mode inactive timeout (minutes): default 20

concern, then you can set XS1000 as TCP Client. Be

( 0=Disable)

sure the value of item Remote Connection Port

If you want to keep the connection between XS1000 and your

Number is same as your remote control application

remote control application always on, then set the value of item

using the correct value of Remote Host IP Address.

Client mode inactive timeout (minutes) to 0, otherwise,

when the inactive time of no traffic on the line reach the
configured value, the XS1000 will terminate the connection.
5.4 TCP Client
5.0 Load default setting

Remote Connection Port Number: default 23, range 0 to

Allows the user to reset the XS1000 to default settings. The

65535

MAC Address will not be updated.

Remote Host IP Address: default 210.200.181.102

If your device is acting as an active device to report real-time

6.0 UART Control (RS-232)

status to remote devices and the data needs to be guaranteed

Use VCOM for creating a new COM port.

to be received by the peer is your concern, then you can set the

The XS1000 support three serial types: RS232, RS422 and

5.1 Telnet

XS1000 as TCP Client. Be sure the value of the setting Remote

RS485.

Telnet connection setting:

Connection Port Number is same as your remote control

Baud Rate: default 57600, range 300bps to 230.4Kbps.

Telnet Server/Client: Currently used to determine if the device is

application using the correct value of Remote Host IP

Character Bits: 5, 6, 7, 8 (default).

a Telnet Server or Client.

Address.

Parity Check: None (default), even, odd, space, mark.

5.2 Operation mode

5.5 UDP Server

Stop Bits: 1 (default), 1.5 or 2.

The XS1000 supports four operation modes: TCP Server,

Local Port Number: default 21, range 0 to 65535

Hardware Flow Control: None (default) or Hardware.

TCP Client, UDP Server and UDP Client. These modes

If your device is acting as a passive device to accept

are listed in the Web page for the Operation Mode setting.

commands from a remote device and the data needs to

Each setup screen and available features will differ

be guaranteed to be received by peer is not your concern,

depending on what kind of operation mode you select.

then you can set XS1000 as UDP Server. Be sure the

Default is TCP Server.

value of item Local Port Number is same as what your

5.3 TCP Server

remote application is using.

Port Number: default 23, range 0 to 65535

5.6 UDP Client

If your device is acting as a passive device to accept

Remote Connection Port Number: default 21, range 0 to

commands from a remote device and the data needs to be

65535

guaranteed to be received by the peer is your concern, then

Remote Host IP Address: default 192.168.2.2

you can set the XS1000 as TCP Server. Be sure the value of

If your device is acting as an active device to report

the setting Port Number is same as your remote control

real-time status to a remote device and the data be

application using.

guaranteed to be received by the peer is not your

Mechanical dimensions

32mm

25m

94mm

XS1000

10mm

45mm

19.5mm

65mm

25mm

Note to Admin Panels UART Control advanced settings:

Character 1 and 2: These are HEX numbers. Default value: 00FF. When sending data from serial to TCP the data is fist
stored in the cache, not until the value of character 1 or 2 is received from the serial side the data is released from the cache and sent to TCP.
Silent time: If there is no data sent or received for the number of milliseconds specified the connection is dropped.
Drop character: Drops the delimiter character of the serial port when sending to TCP, (the receiver doesn't display the character).

How to hardware reset XS1000

To access technical support, please visit the U.S.

1. Disconnect the Ethernet cable

www.USconverters.com

2. Disconnect the serial cable

Here you will find:

Converters website at:

3. Disconnect the power supply

4. Unscrew the two screws on each side on the unit and carefully remove the cover

- Latest drivers and updates for download

5. Locate the small white reset button, next to the power supply jack

- Technical tips

6. Press and hold the reset button

- Documentation

7. While holding the reset button connect the power supply

- Configuration support

8. The Power LED light will come on

- and much more

9. After 7 10 seconds, while holding the reset button, the green LED will flash briefly one time
10. The ATC-1000 now has been reset to factory settings

Feel free to contact our technical support team at

Notice: the unit can also be reset from the web interface

[email protected] with any issues.

Copyrights U.S. Converters