Scribd
Upload
170 views20 pages

SyTech ISPACE - ICD Telex Products

The iSPACE iDEN Card integrates the Motorola iO-270 iDEN Module with the convenience and dependability of a standalone carrier card.

Uploaded by

SyTech Corporation
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
170 views20 pages

SyTech ISPACE - ICD Telex Products

The iSPACE iDEN Card integrates the Motorola iO-270 iDEN Module with the convenience and dependability of a standalone carrier card.

Uploaded by

SyTech Corporation
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 20

Interconnect Documentation for use with TELEX Products

Designed and Manufactured by:

Systems Engineering Technologies Corporation


6121 Lincolnia Road
Alexandria, Virginia 22312
TEL. 703-941-7887
www.SyTechCorp.com

iSPACE Card Settings - Standard

RF Connector
Type: TNC(F)
Impedance: 50 Ohms

Status Indicators
3VDC
4VDC
RXD
TXD
Red Status Green Status

External connections available via DB-15(F)


Pin 1: Output, RS-232, CD
Pin 2: Output, RS-232, TXD
Pin 3: Input, RS-232, RXD
Pin 4: Input, RS-232, DTR
Pin 5: Ground
Pin 6: NC
Pin 7: Output, 128mVrms, Audio (balanced)
Pin 8: Input, 43.5mVrms, Audio (balanced)
Pin 9: Output, RS-232, DSR
Pin 10: Input, RS-232, RTS
Pin 11: Output, RS-232, CTS
Pin 12: Output, RS-232, RI
Pin 13: Ground
Pin 14: Output, 128mVrms, Audio (balanced)
Pin 15: Input, 43.5mVrms, Audio (balanced)

iDEN Module Function Switch


Enabled

(To the Left)

Disabled

(To the Right)

Status Indicators
3VDC LED: Steady Green 3VDC OK
4VDC LED: Steady Green 4VDC OK
RXD LED: Flickering Yellow Data from
Host
TXD LED: Flickering Yellow Data to Host
Red Status LED: See Below
Green Status LED: See Below
Alternating Red and Green Flashstrap
Fatal Error was detected during power-up.
Flashing Red Registering, the device is
registering with the carriers network. Pleas
wait.
Steady Red No Service.
Flashing Red and Green (together) Unit
registered, No packet data service. (no
phone service).
Flashing Green In Full service (phone,
DC, GC)
Steady Green In Use.

TELEX IP-223
Remote Adapter
Configuration Screen Shots and Jumper Settings

TELEX IP-233 required the iSPACE RALP Version


SyTech Part Number P/N: RIOS-iDEN-R

Note: After making changes power reset this device

Screen Shot Copyrights to Telex Communications 2008

iSPACE TELEX IP 223 Common Application

800 MHz Antenna

iDOCK 8-Channel Chassis


P/N: RIOS-iDEN-8CH

Radio 1

iSPACE iDEN Cards (8)


with 2 cards in use

Serial Connection
Radio 2

C-SOFT Dispatch Console

Cable Connections
Interfacing Telex IP-223 to SyTech iSPACE iDEN Card without using the Telex
NI-223 Nextel interface unit.
Single iSPACE connected to Telex IP-223 Radio 1 connector

NOTE: USE QUALITY SHIELDED


CABLE FOR AUDIO LINES

P/N: RIOS-CAB-iDEN-S

1
2

CD
RxD
TxD
DTR
GND

iSPACE
DB-15(M)

RXAL
TXAL
DSR
RTS
CTS
RI
GND
RXAH
TXAH

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15

13
14
15
16
17
18
19
20
21
22
23
24
25

TXAL (GND)

1
2
3
4
5
6
7
8
9

RX L1 TTL
TX L1 RS232
RX L1 RS232
TX L2 TTL
NC
RX L2 TTL
RX L2 RS232
TX L2 RS232
TX L1 TTL

TELEX
RADIO 1
DB-25(M)

RXAH
TXAH

TELEX
Serial
DB-9(M)

Cable Connections
Interfacing Telex IP-223 to SyTech iSPACE iDEN Card without using the Telex
NI-223 Nextel interface unit.
Single iSPACE connected to Telex IP-223 Radio 2 connector

NOTE: USE QUALITY SHIELDED


CABLE FOR AUDIO LINES

P/N: RIOS-CAB-iDEN-S
1
2

CD
RxD
TxD
DTR
GND

iSPACE
DB-15(M)

RXAL
TXAL
DSR
RTS
CTS
RI
GND
RXAH
TXAH

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15

13
14
15
16
17
18
19
20
21
22
23
24
25

TXAL (GND)

1
2
3
4
5
6
7
8
9

RX L1 TTL
TX L1 RS232
RX L1 RS232
TX L2 TTL
NC
RX L2 TTL
RX L2 RS232
TX L2 RS232
TX L1 TTL

TELEX
RADIO 2
DB-25(M)

RXAH
TXAH

TELEX
Serial
DB-9(M)

Dual iSPACE connected to Telex IP-223 Radio 1 and 2 Connector

NOTE: USE QUALITY SHIELDED


CABLE FOR AUDIO LINES

P/N: RIOS-CAB-iDEN-R

1
2

CD
RxD
TxD
DTR
GND

iSPACE 1
DB-15(M)

RXAL
TXAL
DSR
RTS
CTS
RI
GND
RXAH
TXAH

CD
RxD
TxD
DTR
GND

iSPACE 2
DB-15(M)

RXAL
TXAL
DSR
RTS
CTS
RI
GND
RXAH
TXAH

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15

13
14
15
16
17
18
19
20
21
22
23
24
25

TXAL (GND)

1
2
3
4
5
6
7
8
9

RX L1 TTL
TX L1 RS232
RX L1 RS232
TX L2 TTL
NC
RX L2 TTL
RX L2 RS232
TX L2 RS232
TX L1 TTL

TELEX
RADIO 1
DB-25(M)
RXAH
TXAH

1
2
13
14
15
16
17
18
19
20
21
22
23
24
25

TXAL (GND)

TELEX
RADIO 2
DB-25(M)

RXAH
TXAH

TELEX Screen Shots for use with iSPACE

TELEX IP223 Jumper Setting for use with iSPACE

JUMPER
SIGNAL

LINE 1

LINE2

POSITION

2 or 4 Wire

J33, J34

J5, J6

4 Wire

RX Input Type

J16, J21

J19, J20

Single
Ended

RX Input
Impedance

J14

J24

600
Ohms

TX Output Type

J3, J9, J11

J25, J28,
J29

Single
Ended

TX Output
Impedance

J17, J22

J10, J15

600
Ohms

TX Output Level

J13

J27

High

Digital Pull up

J8

J30

+12 Volts

Serial Data

J35

J26

RS232

TELEX IP-2002
Dispatch Console
Configuration Screen shots

Note: After making changes power reset this device

TELEX IP223 and IP2002 with iSPACE Network

P/N: RIOS-iDEN-2CH

SyTech
2 ea. iSPACE-R Cards

Local Network

TELEX
IP-223 Firmware Ver. 4.1
PCB 750743

TELEX
IP-2002 Firmware Ver. 4.1

Testing and configuration of the TELEX IP-223 functioning with the


SyTech iSPACE as depicted with the below configuration. This
configuration set both IP-223 port to work as iDEN devices. Other
configurations can easily be extrapolated.

Continued on Next Page

Line One Continued

Continued on Next Page

Line Two Continued

You might also like