Scribd
Upload
76 views

18.2 Fundamental Principle: Module 5: Directional Overcurrent Protection Lecture 18: Directional Overcurrent Relaying

This document discusses the fundamental principles of directional overcurrent relaying. It explains that directional overcurrent relays compare the phase angle of relay current to the bus voltage phasor to determine if fault current is flowing away or toward the relay. If current lags the voltage phasor, the relay permits tripping, but if current leads the voltage phasor, the relay inhibits tripping. Directional overcurrent relays add this directional discrimination logic to traditional overcurrent logic and are used in distribution and subtransmission systems with ring configurations to provide more reliability. The document also discusses how directional units can be designed for phase and ground faults by using the reference phase voltage and establishing operating lines to separate operate and do not operate regions.

Uploaded by

Ravinder Sharma
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
76 views

18.2 Fundamental Principle: Module 5: Directional Overcurrent Protection Lecture 18: Directional Overcurrent Relaying

This document discusses the fundamental principles of directional overcurrent relaying. It explains that directional overcurrent relays compare the phase angle of relay current to the bus voltage phasor to determine if fault current is flowing away or toward the relay. If current lags the voltage phasor, the relay permits tripping, but if current leads the voltage phasor, the relay inhibits tripping. Directional overcurrent relays add this directional discrimination logic to traditional overcurrent logic and are used in distribution and subtransmission systems with ring configurations to provide more reliability. The document also discusses how directional units can be designed for phase and ground faults by using the reference phase voltage and establishing operating lines to separate operate and do not operate regions.

Uploaded by

Ravinder Sharma
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Module 5 : Directional Overcurrent Protection

Lecture 18 : Directional Overcurrent Relaying


18.2 Fundamental Principle


Thus, if we measure the bus voltage phasor V
p
and compute the phase angle of
relay current with respect to bus voltage, then we can use the following logic to
provide selectivity. If the relay 'detects fault' and current lags V
R
(=V
p
), then
permit relay tripping. If the relay 'detects fault' and current leads V
R
(=V
p
), then
inhibit the relay tripping. The 'discrimination principle' based on phase angle
comparison between a set of phasors, one of which is used as reference is called
'directional discrimination principle'. Relays with this principle are called
directional relays.

For example, overcurrent relays can be made directional by adding above
discrimination logic to well known overcurrent logic. Such relays are called as
directional overcurrent relays. They are used in distribution system or
subtransmission system where 'ring main' configuration is used to provide more
reliability of service. Cost of this relaying scheme is higher than 'non-directional'
overcurrent due to additional cost of VT.

We now discuss the choice of reference phasor for various type of phase and ground faults. Recall that phase relays are
used to protect against phase fault (3 phase and L-L).

Now, with traditional overcurrent relays, a directional overcurrent relay can be visualized as a cascade connection of 'one
directional unit' and one overcurrent unit. If the polarity of the current is appropriate, then directional unit picks up. If the
current magnitude is above pickup, then the overcurrent unit also picks up and when both units pickup, the trip coil is
energized and CB tripping is ensured. In a numerical relay, this can be programmed by a simple 'AND' logic.

Any fault involving ground is called a ground fault. Traditionally, three phase relays and one ground relay have been used
to protect a feeder or a transmission line. However, in a numerical relay, all these functions can be integrated into a single
relay which acquires 3-phase voltages and 3-phase currents.

Design of Directional Units for Phase Fault
Let us first consider, a three phase fault. In this case, choice of the reference phasor can be the phase voltage itself. For a
purely reactive circuit, the fault current in the correct direction lags the reference phasor by . With respect to reference
phase 'V
a
', we can draw operating line (also called as zero torque line due to legacy of electromechanical realys) which
separates the plane into two regions marked as 'operate' and 'Do not operate'. If the fault is in the operating region, then I
a
lags V
a
and we issue trip decision. In case, fault is behind the relay, the fault current leads V
a
and hence lies in the "do not
operate" region.


1 2 3 4 5 6 7 8 9
Page 1of 1 Text_Template
8/1/2009 http://www.cdeep.iitb.ac.in/nptel/Electrical%20Engineering/Power%20System%20Protection/Module-5/Lec-1...

You might also like