Scribd
Upload
154 views9 pages

Study Set 08

This document provides instructions for 10 problems involving creating section views and 3D models of mechanical parts from given figures. Students are asked to sketch or use CAD software to draw full section views, offset section views, and half section views of parts with given grid sizes. They are also asked to draw views and sections from given cutting planes and to construct 3D solid models of parts and create the necessary multiview drawings including sections.

Uploaded by

Mercy John
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
154 views9 pages

Study Set 08

This document provides instructions for 10 problems involving creating section views and 3D models of mechanical parts from given figures. Students are asked to sketch or use CAD software to draw full section views, offset section views, and half section views of parts with given grid sizes. They are also asked to draw views and sections from given cutting planes and to construct 3D solid models of parts and create the necessary multiview drawings including sections.

Uploaded by

Mercy John
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 9

1/9

STUDY SET 08
SECTION VIEWS
PROBLEMS FOR LABORATORY WORK
8.1 Problem 8.1 (Figure 8.53 (C))
Sketch, or draw with CAD, full-section views. Each grid is 0.25 or 10 mm.

8.2 Problem 8.2 (Figure 8.54 (D))
Sketch, or draw with CAD, offset-section views. Each grid is 0.25 or 10 mm.

2/9

8.3 Problem 8.3 (Figure 8.55 (B))
Sketch, or draw with CAD, half-section views. Each grid is 0.25 or 10 mm.

8.4 Problem 8.5 (Figure 8.57 (5))
Sketch, or draw with CAD, the views with sections as indicated by the cutting plane lines. Each grid is 0.25 or 10
mm.

3/9

8.5 Problem 8.5 (Figure 8.57 (18))
Sketch, or draw with CAD, the views with sections as indicated by the cutting plane lines. Each grid is 0.25 or 10
mm.

8.6 Problem 8.6 (Figure 8.59) Counter Block
Sketch, or draw with CAD, then create the necessary views, including a section view, or create a 3-D model.

8.7 Problem 8.6 (Figure 8.63) Taper Collar
Sketch, or draw with CAD, then create the necessary views, including a section view, or create a 3-D model.

4/9

8.8 Problem 8.6 (Figure 8.65) Heavy-Duty V-Pulley
Sketch, or draw with CAD, then create the necessary views, including a section view, or create a 3-D model.

8.9 Classic Problem 1 End Plate
Select views that will best describe the piece. Draw the multiviews, one of which is sectioned.

8.10 Figure 8.70 Roller-Model TX
Construct 3-D solid part, then create the necessary views, including a section view.


5/9

SELECTEDPROBLEMS
8.1 Problem 8.1 (Figure 8.53 (D))
Sketch, or draw with CAD, full-section views. Each grid is 0.25 or 10 mm.

8.2 Problem 8.2 (Figure 8.54 (C))
Sketch, or draw with CAD, offset-section views. Each grid is 0.25 or 10 mm.

8.3 Problem 8.3 (Figure 8.55 (A))
Sketch, or draw with CAD, offset-section views. Each grid is 0.25 or 10 mm.

6/9

8.4 Problem 8.5 (Figure 8.57)
Sketch, or draw with CAD, the views with sections as indicated by the cutting plane lines. Each grid is 0.25 or 10
mm.



7/9

8.5 Figure 8.71 Shift Link
Construct 3-D solid part, then create the necessary views, including a section view.

8.6 Figure 8.72 Hand Wheel
Construct 3-D solid part, then create the necessary views, including a section view.

8/9

8.7 Figure 8.74 Ceiling Fan Cover
Construct 3-D solid part, then create the necessary views, including a section view.

CLASSIC PROBLEMS
8.1 Classic Problem 2 Piston Cap
Select views that will best describe the piece. Draw the multiviews, one of which is sectioned.

9/9

8.2 Classic Problem 4 Column Collar
Select views that will best describe the piece. Draw the multiviews, one of which is sectioned.

You might also like