Near edge X-ray absorption fine structure spectroscopy as a tool to probe

electronic and structural properties of thin organic films and liquids

Georg Hahner
Received 29th March 2006
First published as an Advance Article on the web 13th June 2006
DOI: 10.1039/b509853j
Synchrotron-based spectroscopic techniques have contributed significantly to a better
understanding of the properties of materials on the macroscopic and microscopic scale over the
last decades. They can be applied to samples from a diversity of fields, including Biology, Life
Sciences, Chemistry and Materials. One of these techniques is Near Edge X-Ray Absorption Fine
Structure (NEXAFS) spectroscopy, revealing electronic structure and information on the
orientation of adsorbed molecules. The present article describes the basics of the technique and
the progress it has made over the last three decades, and summarizes some of its more recent
developments and applications. This tutorial review article should be accessible for novices to the
field from Physics, Chemistry, Biology, Materials, and the Life Sciences, interested in thin organic
films and liquid systems.
1. Introduction
Electronic and structural properties are of utmost importance
for a fundamental understanding of the macroscopic and
microscopic behavior of materials. Surface properties play a
particularly important role since they determine the interaction
of an object with its environment. Basic knowledge of the
structure and electronic characteristics of the surface of a
material is therefore crucial for many applications, e.g., in the
Life Sciences, in Biology, or where advanced materials are
involved. Examples of surface properties that are determined
by electronic and structural characteristics are tribological
behavior, wetting, and biocompatibility. Fundamental knowl-
edge can also lead to a tailoring and tuning of these properties,
which is a challenge in current interfacial science.
Tools and techniques to explore electronic and structural
properties have been developed over the last century. One
example is synchrotron radiation sources, which were first
built in the 1940s, but have been employed as an independent
tool to investigate materials since some 40 years ago.
1
Over the
last three decades, they have contributed significantly to a
better understanding of materials on the molecular and
macroscopic scale and opened up entirely new avenues to
explore matter. In the past, most synchrotron radiation
research was performed in parasitic mode, using the radiation
that was produced as a by-product of high-energy physics
experiments. In contrast to these first-generation synchrotrons,
newer facilities are dedicated solely to generating synchrotron
light for use as a probe in science (second and third generation
facilities). Todays synchrotron sources are brilliance-
optimized, i.e. provide a beam with a small beam cross section
and a high degree of collimation, using special devices called
wigglers and undulators.
1
Many synchrotron-based techniques have been developed
that allow the detailed exploration of the properties of
different materials. The technique called near-edge X-ray
absorption fine structure spectroscopy (NEXAFS) was devised
in the 1980s, mainly in order to resolve the structure of
molecules bonded to surfaces. It was particularly intended to
be applied to so-called low-Z molecules (Z is the atomic
number), i.e. mostly organic molecules that consist of light
atoms such as carbon, nitrogen, oxygen and fluorine.
2
Since
then it has been applied to many other molecules and
materials. It probes transitions from (usually) the K-edge
(deepest core shell) of an atomic species into molecular orbitals
of bonds to intra-molecular and extra-molecular (surface
atoms) neighbors. NEXAFS is a powerful structural tool that
provides information on the electronic structure and orienta-
tion of molecules or molecular fragments. The present article
EaStCHEM School of Chemistry, North Haugh, University of St
Andrews, St Andrews, Fife, UK KY16 9ST.
E-mail: [email protected]
Georg Hahner studied Physics
at the University of Gottingen
(Diploma) and obtained a PhD
in Physical Chemistry from the
University of Heidelberg,
Germany. He carried out post-
doctoral research at the ETH
Zu rich, Switzerland, which
earned him a habilitation in
Materials Sciences. He was a
Lecturer in the Physics depart-
ment at University College
London, UK, and is currently
a Reader in Physical Chemistry
at the Uni versi ty of St
Andrews, UK.
Synchrotron radiation and in particular NEXAFS spectroscopy
have played a major role in Dr Hahners research activities for
more than a decade. The technique was mainly applied in
connection with ultrathin organic films on a variety of different
substrates.
Georg Hahner
TUTORIAL REVIEW www.rsc.org/csr | Chemical Society Reviews
1244 | Chem. Soc. Rev., 2006, 35, 12441255 This journal is The Royal Society of Chemistry 2006
describes the basics of this technique and compares it briefly to
other in-house laboratory surface analytical tools revealing
similar information. Selected examples of applications are
given to demonstrate the breadth and the strength of this
particular type of spectroscopy.
2. Experimental section
2.1 Properties of synchrotron radiation
Electric charges that are accelerated, i.e. experience a force,
generate electromagnetic radiation. This fact is exploited for
the generation of synchrotron radiation, where charges
usually electronsare forced to move on a curved path.
Synchrotron radiation facilities concentrate on the production
of such radiation. A synchrotron radiation facility consists of a
storage ring and a booster, where the charged particles are
accelerated close to the speed of light before being injected into
the storage ring (Fig. 1). The synchrotron booster is a roughly
circular ring of magnets for focusing and bending the electron
beam, and straight sections for accelerating the particles. The
magnetic field is raised synchronously (hence the term
synchrotron) with the particle energy to keep the electrons
on a circular path with a constant radius. When the electrons
have reached the desired relativistic energy, they are trans-
ferred to the storage ring, where the magnetic field remains
constant. The electrons then orbit in the storage ring, i.e. a
circular accelerator. Synchrotron radiation is generated in
bending magnets keeping the electrons on a closed path, and in
wigglers or undulators that are placed into the linear sections.
1
In the bending magnets and insertion devices the electrons are
subject to acceleration and therefore emit radiation.
Synchrotron radiation obtained from the storage ring covers
a wide range of the electromagnetic spectrum. The detailed
frequency characteristics of the radiation depend on para-
meters such as the number and the energy of the stored
electrons, and hence differ for the different synchrotron
sources around the world. However, it provides a continuous
spectrum over a wide energy range, with the energy of
maximum intensity depending on the energy of the electrons.
3
The radiated flux is superior to most conventional sources by
orders of magnitude. In combination with the broad spectral
range it is, in fact, unmatched by any other source.
The light is conveyed to experimental chambers through
beamlines. A monochromator in the beamline helps to select a
single wavelength thus providing a high-brilliance, tunable,
monochromatic X-ray source for the experimentalists. In
addition to its high brilliance the synchrotron light is
polarized. It is (almost) linearly polarized in the plane of the
storage ring for bending magnets and undulators.
3
The degree
of polarization is determined by the X-ray energy and the
beamline optics.
When the radiation enters the users experimental chamber
it has two properties which distinguish it from conventional
X-rays created by in-house laboratory X-ray sources, and
which are exploited in NEXAFS: Firstly, it is a tunable
monochromatic source of X-rays and secondly, the radiation
has a high degree of polarization. Depending on the machine
settings circularly or linearly polarized light can be obtained.
While historically the application of synchrotron radiation is
confined to samples in a vacuum, more recently techniques
have been developed that also allow its application to samples
in high pressure and liquid environments. This makes it a very
attractive technique for the Life Sciences and biological
applications.
2.2 The NEXAFS technique
Compared to other types of X-ray absorption spectroscopy,
NEXAFS is a relatively young technique. It probes the
absorption of electromagnetic radiation by excitation of core
electrons into unoccupied bound or continuum states. The
near edge X-ray absorption fine structure exhibits strong and
distinctive features in the energy region just below and up to
about 50 eV above the absorption edge (e.g. K-edge).
2.2.1 Electron- and fluorescence yield NEXAFS. During a
measurement the sample is irradiated with monochromatic
X-rays. The energy of the X-rays is varied around an
ionization edge. The dominant process in the soft X-ray
energy range (,2000 eV) is (by orders of magnitude)
photoabsorption. The absorption process results in a photo-
electron and a core hole. The hole is subsequently filled by an
electron either radiatively by the emission of a fluorescent
photon, or non-radiatively by the emission of an Auger
electron (see Fig. 2). Both channels are a direct measure of the
existence of a core hole created by the X-ray absorption and
are therefore a measure of the absorption cross section. In
Fig. 1 Schematic of a synchrotron facility. Electrons are injected
into an electron synchrotron (Booster) at a relatively low energy
(y100 MeV) and accelerated to yGeV before being transferred to the
storage ring.
Fig. 2 Energy diagram of the photoabsorption process and the
subsequent filling of the core hole by emission of a photon or an Auger
electron.
This journal is The Royal Society of Chemistry 2006 Chem. Soc. Rev., 2006, 35, 12441255 | 1245
principle, either channel can be detected. For electrons, a
channeltron or an energy analyzer can be employed, while
measuring radiative emission requires a fluorescence detector.
However, the Auger electron yield is much higher than the
fluorescence yield for low-Z molecules (composed of atoms
such as carbon, nitrogen or oxygen).
4
In addition, electron
detection provides the higher surface sensitivity and in the
majority of studies published in the literature this detection
scheme has been employed.
The reason for the higher surface sensitivity is the relatively
low kinetic energy of the electrons and the corresponding mean
free path in matter, which is typically less than 1 nm for
energies between 250 eV and 600 eV.
5
Although the X-ray
photons penetrate many microns deep into the sample, the
electrons generated at that depth do not emerge from the
sample. The inelastic scattering process leads to an electron
cascade, of which only those electrons with sufficient energy to
overcome the work function of the material will escape the
surface. The resulting effective escape depthand therefore
the information depth of electron yield NEXAFShas been
estimated to be in the range of 5 nm for metals and
semiconductors, and slightly larger for insulators due to the
reduced electronelectron scattering mechanism.
2
The surface
sensitivity can be further enhanced by applying a retarding
voltage before the electrons enter the channeltron. By
suppressing lower kinetic energy electrons, only those electrons
that emerge from the outermost surface region (#3 nm) are
detected. For the investigation of adsorbates on surfaces, this
so-called partial electron yield (PEY) detection has a better
signal-to-background ratio than total electron yield (TEY)
detection, where all electrons that emerge from the surface are
detected. A further option is Auger electron yield (AEY)
detection, where only elastically scattered Auger electrons are
recorded. The AEY mode requires an electron energy analyzer
but provides the best surface sensitivity of the three detection
techniques.
In the case of fluorescence detection, an appropriate
detector has to be employed. As mentioned before, the effect
for low-Z molecules is lower compared to the electron yield.
As a general rule PEY, AEY and fluorescence yield (FY) all
exhibit a sufficiently large signal-to-background ratio for most
thin film samples.
2
The detection technique best suited to a
particular sample depends on the type of sample and the
optimum signal-to-noise ratio. Note that FY detection is the
method of choice for studies of samples in liquid environments
due to the limited mean free path of the electrons, and in the
energy range below 1000 eV in gaseous environments. Its
power in connection with such environments has recently been
demonstrated (see 3.3 below).
2.2.2 Origin of NEXAFS spectrainformation on electronic
structure. An understanding of the various features observed in
NEXAFS spectra is a prerequisite for the use of NEXAFS as a
tool to investigate electronic structures and molecular orienta-
tions. In the following, a brief phenomenological description
of these features and their origin is given.
A NEXAFS spectrum reflects the dependence of the
photoabsorption cross section on the photon energy for values
from just below the ionization threshold up to around 50 eV
above it. In general, the energy dependence of the atomic
photoabsorption cross section resembles a step function. At
high energies, E, it is identical with the ionization cross section,
i.e. proportional to E
27/2
.
6
The absorption step results from
the excitation of the core electron to a continuum or quasi-
continuum of final states. It is almost always obscured by
transitions into Rydberg states. The origin of NEXAFS
features is schematically illustrated in Fig. 3. The effective
potential and corresponding K-shell spectrum for a diatomic
unit are shown. Around the ionization threshold, resonant
transitions are superimposed on the step-like shape. Such
transitions occur if the energy of the incoming photons
matches exactly the energy difference between the initial state
and an unoccupied (molecular) state. Unfilled molecular
orbitals are labeled as p*- or s*-orbitals according to their
symmetry.
The lowest unoccupied molecular orbital of a p-bonded
diatomic subunit of a molecule is usually a p*-orbital, while
s*-orbitals are found at higher energies. The latter are most
often found above the vacuum level for the neutral molecule.
However, the p*-state is pulled below the ionization potential
by the electronhole Coulomb interaction.
2
Of course, a 1s A
p*-transition or p*-resonance can only be observed for
Fig. 3 Schematic potential (bottom) and corresponding NEXAFS
K-shell spectrum (top) of a diatomic molecular (sub)group. In addition
to Rydberg states and a continuum of empty states similar to those
expected for atoms, unfilled molecular orbitals are present, which is
reflected in the absorption spectrum.
1246 | Chem. Soc. Rev., 2006, 35, 12441255 This journal is The Royal Society of Chemistry 2006
molecules with p-bonding, i.e. double and triple bonds or
aromatic systems, but not for single bonds.
The measured width of a resonance is determined by the
resolution of the instrument (resulting in a Gaussian line-
shape), the lifetime of the excited state (resulting in a
Lorentzian lineshape), and the vibrational motion of the
molecule leading to an unsymmetrical broadening. Broadening
due to the lifetime of a p*-resonance is generally very small,
because the final state lifetime is determined by the de-
excitation of the excited electron, i.e. the decay of the core
hole. Broader resonances that arise from transitions to orbitals
of s-symmetry can usually be found at higher energies above
the threshold. Because of the large overlap of these states with
the continuum, the decay probability of the electron to
continuum states increases. As a rule of thumb, the higher
the resonance lies in the continuum the larger is its linewidth. If
the resolution is high enough the vibronic broadening can be
observed.
2
The asymmetric lineshape of s*- resonances is
therefore a consequence of a combination of lifetime broad-
ening and molecular vibration along the bond direction.
In some cases, the energy positions of s*-resonances depend
sensitively on the length of the corresponding bond. This has
been exploited to estimate bond lengths from NEXAFS
spectra (the so-called bond length with a ruler concept).
2
Rydberg orbitals give rise to sharp but weak resonances.
They are generally located between the p*-resonance and the
ionization potential. In the condensed phase or for strongly
chemisorbed molecules, pure Rydberg resonances are
quenched because of the large spatial extent of the orbitals,
which have most of their orbital density at the periphery of the
molecule. In the presence of bonds to hydrogen atoms, mixing
of Rydberg orbitals with hydrogen-derived antibonding
orbitals of the same symmetry increases the intensity of the
corresponding resonance. In particular, the C K-edge spectra
of hydrocarbons and other molecules with CH bonds show
pronounced features that are best described as mixed Rydberg/
valence resonances.
7,8
Finally, NEXAFS spectra can also exhibit multi-electron
features, such as so-called shake-up structures (analogous to
those observed with X-ray photoelectron spectroscopy). For a
more detailed discussion see ref. 2.
2.2.3 Angular dependence of the spectrainformation on the
molecular orientation. In addition to the information on the
electronic structure of molecules or molecular fragments,
NEXAFS can also reveal information about their orientation.
For this purpose, the polarization characteristics of synchro-
tron radiation are exploited. By taking NEXAFS measure-
ments at two or more angles of incidence of the X-rays, the
spatial orientation of an orbital can be extracted. Synchrotron
radiation from a bending magnet is almost linearly polarized in
the plane of the storage ring. For the sake of simplicity, we will
assume that the radiation is linearly polarized in the following.
The quantum mechanical description of the excitation process
for a single electron in the dipole approximation leads to an
equation relating the initial state, Y
i
, and the final state, Y
f
, to
the absorption cross section, s
x
(Fermis Golden Rule):
s
x
3 |SY
f
|e?p|Y
i
T|
2
r
f
(E) (1)
with e being the unit electric field vector, p the dipole transition
operator, and r
f
(E) the density of final states.
2
Bonds and the associated molecular orbitals are highly
directional and the spatial orientation of an orbital, i.e. the
direction of maximum orbital amplitude on the excited atom,
determines the angular dependence of the K-shell spectra.
Therefore, the transition intensities depend on the orientation
of the electric field vector relative to the orientation of the
molecule. Note that s*-orbitals have a maximum orbital
amplitude along the bond axis while p*-orbitals have
maximum amplitude normal to the bond direction.
In the case of linearly polarized light, the angular
dependence of the matrix element of interest |SY
f
|e?p|Y
i
T|
2
=
|eSY
f
|p|Y
i
T|
2
assumes a simple form. For a 1s initial state and a
directional final state orbital the matrix element SY
f
|p|Y
1s
T
points in the direction of the final state orbital O and the
transition intensity becomes
I 3 |eSY
f
|p|Y
1s
T|
2
3 |eO|
2
3 cos
2
d (2)
with d being the angle between the electric field vector, E, and
the direction of the final state orbital, O. Therefore, the
intensity of a resonance is largest when the electric field vector
E lies along the direction of the final state molecular orbital (as
schematically shown in Fig. 4), and vanishes when E is
perpendicular to it.
Recently, techniques have been developed that allow eqn (1)
to be solved numerically with high precision. These theoretical
calculations reveal subtle details in NEXAFS spectra and lead
to a deeper understanding of the underlying processes. The
approach is based on multiple-scattering theory. The
NEXAFS spectra are thought to result from the multiple-
scattering of the electrons involved. Readers interested in the
details are referred to the literature, e.g. ref. 9,10.
2.2.4 Data analysis. To extract quantitative information on
the orientation of bonds, spectra recorded at different angles
of incidence have to be normalized to the flux of the incoming
photons and to the step height.
2
To express the intensity of a
specific resonance in terms of the angle of incidence of the
Fig. 4 Schematic representation of the origin of the angular
dependence of NEXAFS resonances for a p-bonded diatomic molecule
adsorbed with its molecular axis normal to the surface. As a result of
the different overlap between the electric field vector, E, and the
direction of the final state orbitals, O, the p*-resonance is maximized
at normal incidence (left), while the s*-resonance is maximized at
grazing incidence (right).
This journal is The Royal Society of Chemistry 2006 Chem. Soc. Rev., 2006, 35, 12441255 | 1247
incoming X-rays, all dipole transition moments contributing to
the resonance must be taken into account. In principle, the tilt
angle of a molecular orbital can then be found by determining
the intensity of the corresponding resonance as a function of
the angle of incidence of the photons, h. This requires a
decomposition of the angle-dependent spectra into their
components by fitting the ionization step(s) and the various
transitions. In the case of molecules with p-bonds, the large p*-
resonance is most suitable for a quantitative evaluation of the
angular dependence because of its clear separation from the
ionization step and the absence of any interfering background.
In this case, the height of the resonance or its area can be
analyzed as a function of the angle, h, yielding the average tilt
angle, a, of the corresponding bond (see 3.2 below).
Note that the spatial resolution of NEXAFS is determined
by the spot size of the X-rays on the surface and the acceptance
area of the analyzer, and is usually macroscopic, i.e. the
information obtained on the electronic structure and the
molecular orientation will normally be an average value from a
macroscopic region.
2.3 Brief comparison to other techniques revealing electronic
and/or structural properties
Compared to other techniques that are used to analyze the
electronic and structural properties in ultrathin molecular
layers, such as infrared (IR) or electron spectroscopy,
NEXAFS has far less stringent requirements regarding
substrates (e.g. IR transparency or electrical conductivity),
and is also highly sensitive even to small adsorbate coverages.
Both X-ray photoelectron spectroscopy (XPS) and ultra-
violet photoelectron spectroscopy (UPS) probe occupied states
in the core region and the valence region, respectively.
Electrons are detected with an electron analyzer. The spectra
consist of peaks corresponding to directly excited elastically
scattered electrons, and a background caused by secondary
and inelastically scattered electrons.
5
In contrast, NEXAFS
probes unoccupied states and is thus complementary to XPS
and UPS. One clear advantage is that is has a very high
sensitivity toward chemical changes and the chemical environ-
ment of an atom. For example, with XPS the C 1s electrons of
a hydrocarbon and an aromatic compound such as benzene
differ by a shift of y0.1 eV in the XPS spectrum, which is
often below the resolution of the analyzer. Consequently, both
signals appear in one peak, which has to be deconvoluted.
Fig. 5 shows the XPS and the NEXAFS C 1s spectra for
grazing and normal incidence of a benzene monolayer
adsorbed on Ag(110). In contrast to the XPS spectrum, the
NEXAFS spectrum of the C 1s edge shows distinct peaks
(separated by several eV), which may be assigned to transitions
to s*- and p*-orbitals. The presence of double bonds is usually
easily recognized.
This confers a very high chemical sensitivity on the
technique. Note, however, that, in contrast to XPS,
NEXAFS is generally not quantitative, because electrons are
integrally collected, i.e. both primary and secondary electrons
are contributing to a resonant peak.
IR and its derivatives can be employed as in-house
techniques to determine the chemical composition and, in
some cases, molecular conformation. IR probes the vibrational
properties of molecules. The energy of the observed bands is
characteristic of the bonds. While IR spectroscopy has been
successfully employed to study many systems, it has certain
selection rules. In order for a vibrational mode to be IR active
there must be a change in the dipole moment when the
molecule vibrates. It can also be difficult to obtain spectra
from monomolecular or sub-monolayer films due to a poor
signal-to-noise ratio. When a molecule is adsorbed on a
conducting surface, only the mode components normal to the
Fig. 5 XPS (left) and NEXAFS spectra (right) of a benzene monolayer adsorbed on Ag(110) recorded at the C 1s edge. The presence of double
bonds is easily recognized from the NEXAFS spectrum in contrast to the XPS spectrum. (Reprinted with permission from ref. 11. Copyright (1991)
Elsevier.)
1248 | Chem. Soc. Rev., 2006, 35, 12441255 This journal is The Royal Society of Chemistry 2006
surface are probed. This fact can be exploited to determine the
orientation of a molecule. Though possible in principle, this is
not straightforward and requires some effort.
12
In order to
extract information on the molecular orientation with
NEXAFS, the measurement of two spectra is required, which
can usually be done within minutes. There are no selection
rules and the technique has very successfully been applied to
determine the molecular orientation of many different systems.
The sensitivity to specific moieties and functional groups,
however, is, in many cases, exceeded by IR.
3. Applications
3.1 Application to small molecules
The technique was first applied to small molecules such as
CO and NO adsorbed on single crystal metal surfaces in the
1980s,
13
and has since then been used successfully to determine
the electronic structure and molecular orientation of many
different molecules on the surfaces of many different
substrates.
As an example, some of the early results obtained for CO
and NO on Ni(100) are shown below to demonstrate the
practical aspects of the technique, i.e. how electronic structure
information and molecular orientation can be obtained from
the spectra. Fig. 6 shows the polarization dependence of
spectra recorded at the C 1s and N 1s edge, respectively. The
number of resonances is small and they can easily be identified.
The sharp feature observable at lower energies is the p*-
resonance (A), while the s*-resonance (B) is much broader
and appears at a higher energy. Of course, similar information
can be obtained by measuring the O K-edge.
There is a clear angular dependence of the resonance
intensities, which can be used to determine the orientation of
the molecule relative to the surface. The p*-resonance is
strongest for normal incidence and disappears for grazing
incidence while the s*-resonance behaves in the opposite way.
This indicates that both CO and NO are standing upright on
the surface. Exact determination of the resonance intensities
allows a more rigorous quantitative determination of the
molecular tilt angles.
Similarly, several other small molecules have been investi-
gated on a variety of surfaces, including N
2
, O
2
, ethylene,
benzene and several of its derivatives.
2
3.2 Application to larger molecules and polymers
3.2.1 Larger molecules. NEXAFS spectra can reveal
information about the electronic structure of molecules or
adsorbates and the orientation of molecular orbitals. In the
discussion of resonances presented so far, the effect of
delocalization or conjugation has not been taken into account.
Systems with significant bondbond interactions experience a
Fig. 6 Angle dependent C and N K-edge NEXAFS spectra of CO and NO adsorbed on a Ni(100) surface. (Reprinted with permission from ref. 13.
Copyright (1981) American Physical Society.)
This journal is The Royal Society of Chemistry 2006 Chem. Soc. Rev., 2006, 35, 12441255 | 1249
splitting of the corresponding energy levels and hence display a
higher number of resonances. In addition to this final state
effect, the number of resonances can also increase because of
an initial state effect. Different chemical environments of the
various excited atoms in a larger molecule can lead to energy
shifts of the resonances.
The number of resonances increases with the number of
atoms of the same element in chemically different environ-
ments in the molecule, making the assignment and evaluation
for larger molecules more challenging. In general, the assign-
ment of resonances in the NEXAFS spectra of larger
molecules can be difficult.
In cases where the observed resonances arise from states that
are localized in space within the molecules, the spectra can be
decomposed into building blocks of diatomic subunits or ring-
like structures (so-called building block scheme
2
). This
approach is valid if the wave function of an orbital has
significant amplitude only in certain parts of the molecule, i.e.
is localized. The entire spectrum is then considered to be a
superposition of the spectra of the building blocks.
Accordingly, the spectra of many molecules can be decom-
posed into contributions stemming from local bonds. This is
caused by the localized nature of the NEXAFS excitations,
which probe the valence orbital final states near the core of the
excited electron. Note however that there are limitations to this
simple scheme, e.g. in molecules with a delocalized p-system.
2
As a starting point the observed resonance positions
obtained for larger molecules are compared with those of the
appropriate building blocks. For molecules containing aro-
matic moieties, for instance, the NEXAFS spectra of benzene
may serve as a clue. In a second step, interactions between
antibonding orbitals have to be taken into account. The
angular variation of the resonances can aid their assignment.
An exact identification is in many cases prevented by the fact
that resonances may overlap with each other and with the
absorption step(s).
Orientation of larger molecules. The determination of the
orientation of larger molecules can be challenging due to the
increasing number of possible conformations. An example
where a p*-resonance can be used to determine the orientation
of larger conjugated molecules is the application of NEXAFS
to dyes, such as methylene blue, adsorbed on mica (see
Fig. 7).
14
Dyes are employed to determine the specific surface
areas of layered silicates. It is usually assumed that the
adsorbed molecules are lying flat on the surface. The
NEXAFS results revealed, however, that the orientation is
significantly different from the presumed flat lying geometry,
having some implication for the determination of specific
surface areas with dye molecules. Note that high quality
spectra in PEY mode were obtained on a highly insulating
substrate.
Films of hydrocarbons up to a chain length of around
25 methylene units are another example of larger molecules
that have been successfully studied with NEXAFS. They
contain a small number of different atoms and building blocks,
and can be treated similarly to small molecules. Alkane chain
based molecules have been studied to some extent and in some
detail both experimentally and theoretically because of their
fundamental importance in many biological and technical
systems. Fig. 8 (left) shows the spectra of a long-chain
hydrocarbon (octadecylphosphoric acid ester) adsorbed on a
metal oxide (TiO
2
) surface. The electronic transitions of
hydrocarbons can be easily identified. The exact assignment
of the molecular orbitals involved, however, has been
discussed in the literature,
2,7,8
and the applicability of the
building block scheme in connection with long chain hydro-
carbons has been questioned. Note that the energetic positions
of all resonances (CH and CC related) are above the
ionization edge. In consequence, to determine the molecular
orientation an exact knowledge of the step shape is required to
extract the intensity of the resonances. A direct determination
of the orientation of the chains is difficult for two reasons.
Firstly, the analysis is extremely sensitive to the exact energy
position of the ionization step, since the intensity associated
with the transition into the CH-orbitals is strongly influenced
by this value. Secondly, an angle independent (isotropic)
background has to be assumed in the fitting procedure.
2
An alternative to this evaluation scheme of the spectra exists
if the orientation of a chemically similar system is known
(Fig. 8, right). Then the orientation can be obtained by
comparison of the angle dependent spectra with those of the
known reference system. This procedure makes use of
difference spectra.
2
It does not require exact knowledge of
the step function, the isotropic background, and instrumental
factors. It has successfully been applied to hydrocarbon based
Fig. 7 Angle dependent N 1s spectra of methylene blue adsorbed on
mica. The p*-resonances labeled 1 and 2 indicate a tilt angle of 70u of
the molecular plane relative to the surface. (Reprinted with permission
from ref. 14. Copyright (1996) American Institute of Physics.)
1250 | Chem. Soc. Rev., 2006, 35, 12441255 This journal is The Royal Society of Chemistry 2006
species on metal oxide surfaces, e.g. ref. 15, as well as on
insulating substrates, such as mica, e.g. ref. 16.
In many cases NEXAFS is employed together with other
surface analytical techniques to reveal a comprehensive picture
of a system under investigation. A recent example is the
investigation of the interaction of water with organic surfaces,
which plays an important role in many fields, for example for
biosensors, medical implants, or drug-release systems. Despite
their crucial significance, the molecular mechanisms under-
lying the wettability of hydrophilic organic surfaces are still far
from being completely understood. Zubavichus and coworkers
have studied the adsorption of water on self-assembled
monolayers (SAMs) of 4-(4-mercaptophenyl)pyridine on gold
at low temperatures under ultrahigh vacuum conditions by
synchrotron radiation, X-ray photoelectron and absorption
spectroscopy.
17
NEXAFS revealed that water adsorption
induces a strong modification of the chemical state of the
pyridine N atoms at the SAM/ice interface, indicative of strong
H-bonding and partial proton transfer between water mole-
cules and pyridine moieties. Additionally, the authors report
that the initial molecular orientation within the SAM changed
upon formation of an adsorbed water multilayer.
A further example is reported in ref. 18. Nelson et al.
employed NEXAFS (amongst other techniques) to investigate
the self-assembly of streptavidin onto biotinylated alkylthio-
late monolayers on gold. This system has served as an
important model system for protein immobilization at
surfaces. They report a detailed study of the surface composi-
tion and structure of mixed SAMs containing biotinylated and
diluent alkylthiolates and their use to specifically immobilize
streptavidin. Films produced on gold from a range of binary
mixtures of a biotinylated alkylthiol (BAT) and either a
methyl-terminated thiol (mercaptohexadecane, MHD) or a
C-11-oligo(ethylene glycol)-terminated (OEG) thiol in ethanol
were investigated. NEXAFS characterization demonstrated
that pure OEG and mixed BAT/OEG SAMs do not show
significant anisotropy in CC bond orientation. In contrast,
the aliphatic segments of MHD and mixed BAT/MHD SAMs
exhibit pseudo-crystalline packing. Adsorption measurements
with streptavidin indicated that it binds both specifically and
nonspecifically to the BAT/MHD SAMs, but purely specifi-
cally to BAT/OEG SAMs. The results obtained contribute to
the clarification of the relationship between the specificity of
streptavidin recognition and the surface architecture and
properties of the mixed SAMs.
3.2.2 Polymers. Polymers play an important role in many
areas of modern technology. The difficulty in determining the
electronic structure and orientation of polymers on a surface
increases with the size of the molecule. The average orientation
of the polymer will often be random due to the huge number of
contributing components and their many different orientations
relative to the surface. NEXAFS spectra can nevertheless be
extremely useful. They can help to establish a fundamental
understanding of the electronic structure, and allow, in some
cases, a quantitative compositional analysis of the polymer.
Huge collections of spectra recorded for many different
polymers have been compiled, see e.g. ref. 19,20. In ref. 20
the authors report a set of NEXAFS spectra from 24 common
polymers that represent a range of chemical functionalities.
This enabled the creation of a database of calibrated polymer
NEXAFS spectra to be used for compositional analysis. These
spectra are used to demonstrate the sensitivity of NEXAFS
spectroscopy to the polymer composition, illustrating the
potential of NEXAFS for chemical analysis.
Chemical sensitivity of NEXAFS. A detailed understanding
of the electronic structure of large molecules is often lacking.
Ade and Urquhart have recently reviewed the use of NEXAFS
to polymer systems.
21
They state, as a rule of thumb, that a
resolution of 50 meV at the C 1s edge often reveals many
subtleties in the NEXAFS spectra of polymers such as splitting
of p*-resonances and vibronic features.
Theoretical calculations can also contribute to a deeper
understanding of the details of electronic spectra, but they are
becoming more difficult with increasing number of atoms and
Fig. 8 C 1s spectra of an alkanephosphate film adsorbed on a metal oxide (left) and spectra of a hexadecane thiol film on gold of known
orientation, serving as the reference system (right). (Reprinted with permission from ref. 15. Copyright (2002) American Chemical Society.)
This journal is The Royal Society of Chemistry 2006 Chem. Soc. Rev., 2006, 35, 12441255 | 1251
can be quite challenging. A recent example of how calculations
can shed some light on the details of NEXAFS spectra is given
in ref. 22. It was shown that subtle differences in the resonance
shape of poly(ethylene) may be attributed to intermolecular
interactions and are not caused by intramolecular interactions,
as had been discussed for some time.
The applicability of the building block scheme can in certain
cases be extended to so-called fingerprint spectra in the case
of polymers. Such spectra are based on larger subunits and
-groups, for example ring units or small molecular units.
Molecular subgroups often show a typical fingerprint spec-
trum. These spectra can be useful for the identification of
similar groups and local bonding environments in macro-
molecules. They can also help to establish the orientation of
particular molecular segments. Fingerprint spectra are
reported in the literature, e.g. ref. 19,20, and can be used as
a starting point to study macromolecules. Ade and Urquhart
discuss, in some detail, the usefulness of the building block
scheme for polymers in their review.
21
An example of the applicability of the fingerprint spectra
was conducted with biological molecules, the aim being to
predict spectra for biopolymers such as peptides and proteins
from amino acids as building blocks.
23
For this purpose, the
carbon spectra of several amino acid monomers were
measured. It was estimated that the formation of bonds has
a relatively weak influence on the NEXAFS spectra of the
macromolecules so that the weighted sum of the monomer
spectra should closely resemble the spectrum of the peptide.
24
It opens up the possibility to predict the NEXAFS spectra of
proteins based on the constituting amino acids. Fingerprint
spectra may also serve to identify regions of high concentra-
tions of certain proteins on a surface, i.e. to map their spatial
distribution, provided the spatial resolution of the beam is high
enough.
Similarly, the C, N, and O K-edge NEXAFS spectra of the
22 most common proteinogenic a-amino acids in the
zwitterionic form collected from solvent-free polycrystalline
powder films in the partial electron yield mode are reported in
ref. 25. Spectral features common to all amino acids, as well as
distinctive fingerprints of specific subgroups of these com-
pounds, are presented and discussed.
Polyurethanes have been at the center of interest in a review
published by Urquhart et al.
26
X-ray spectromicroscopy was
successfully applied to study the chemical composition of
the polymer and a detailed quantitative analysis is presented.
Results are reported outlining a methodology for quantitative
speciation of polyurethane polymers. The goal was to under-
stand the spectroscopic basis for chemical analysis of
polyurethanes. To reach this goal the authors employed C 1s
excitation spectra of a series of molecular and polymeric
model compounds. The model species used contained the
aromatic urea, aromatic urethane (carbamate), and aliphatic
ether functionalities that are the main constituents of
polyurethane polymers. The spectral assignments are sup-
ported by additional ab initio calculations of several of the
model molecular compounds. The calculations also give some
insight into the origin and relative intensities of characteristic
spectral features. The model polymer spectra were then
employed as reference standards for qualitative identification
and quantitative analysis of polyurethane polymers. The
chemical compositions of three polyurethane test polymers
with systematic variation in urea/urethane content were
measured using the spectra of model toluene diisocyanate
(TDI) urea, TDI-carbamate, and poly(propylene oxide) poly-
mers as reference standards.
More examples in which the chemical sensitivity of
NEXAFS was used to characterize the electronic and/or
geometric structure of polymeric materials can be found in the
review by Ade and Urquhart.
21
Orientational sensitivity of NEXAFS. With increasing
molecular size, the number of molecular segments and hence
their tendency to show a random (average) orientation
increases dramatically. One prominent example of oriented
polymer chains in a thin coating is poly(tetrafluoroethylene),
whichdepending on the preparation conditionscan estab-
lish a very high degree of orientational order.
27
In general, the orientation of polymer chains containing
p-bonds and conjugated structures can be determined more
easily than those mainly containing s-bonds, such as aliphatic
chains. This is due to the separation of the p*-resonances from
the ionization threshold as described above. Similar to smaller
molecules, p*- and s*-resonances of unsaturated polymers can
often be easily distinguished.
Another example of the application of NEXAFS to
polymers to extract orientational information is the determi-
nation of a change in the orientation of polymer chains
depending on the depth, i.e. surface versus bulk orientation.
Depth sensitivity can be achieved by applying different
retarding voltages in PEY mode or by comparing TEY versus
PEY versus Auger yield. Again, examples for this can be found
in ref.21.
3.3 Application to liquids and to molecules in liquid environments
Although wet environments play a crucial role for many
biological and chemical processes, much less is known about
the electronic structure of liquids and dissolved species in
comparison to solids and gases. In consequence, significant
efforts have been spent recently on applying the technique to
the liquid state and to molecules in a liquid environment.
Electron yield is not the method of choice for samples in
liquid environments because the mean free path of the
electrons in a liquid is small. In contrast, photons are much
less affected by the presence of the liquid. Fluorescence yield is
one way to explore molecules in liquids or under high
pressure conditions. In the study reported in ref. 28 a UHV
compatible liquid cell sealed from the UHV components of the
synchrotron was employed. X-rays can pass through the cell
without significant loss of intensity and the resulting fluores-
cence yield can then be detected. The authors studied aqueous
solutions of K
4
Fe(CN)
6
and K
3
Fe(CN)
6
, NaCl, and haem-
chloride to explore the local electronic structure and, in
particular, the oxidation state of the solute, namely Fe and Na.
The Fe L-edge for both K
4
Fe(CN)
6
and K
3
Fe(CN)
6
was
measured at 1 M concentration revealing differences in the
electronic structure of the Fe ion. In the case of NaCl,
the signal at the Na K-edge was recorded at different
1252 | Chem. Soc. Rev., 2006, 35, 12441255 This journal is The Royal Society of Chemistry 2006
concentrations. The experimental setup gave reasonable
signals for concentrations down to 100 mM.
The liquid itself has also been the focus of interest in recent
experiments. Water, as the most prominent example, was
studied in view of its hydrogen bonding properties.
29
X-ray
absorption was employed to elucidate the structure in the first
coordination shell of liquid water. A detailed description of the
hydrogen bond network in liquid water is considered to be the
key to understanding its unusual properties. X-ray absorption
spectroscopy at the oxygen K-edge is sensitive to distortions of
H-bonds on the H-sides (donor H-bonds) of the molecules in
the condensed phases of water. The time scale for excitation is
much faster than the molecular (vibrational) motions in the
liquid. Therefore, this technique probes the electronic structure
of a distribution of instantaneous configurations and thus
allows decomposition in terms of specific H-bond situations.
In ref. 29, NEXAFS data for bulk and surface ice and liquid
water are presented. The results are discussed in terms of
double donor, single donor, and no donor configurations
corresponding to two intact donor H-bonds, one intact and
one broken donor H-bond, and two broken donor H-bonds,
respectively. The authors emphasize that their findings are
consistent with neutron and X-ray diffraction data. A
combination of the results sets a limit for possible local
structure distributions in liquid water. They conclude that
water, on the sub-femtosecond time scale being probed,
consists mainly of structures with two strong H-bonds, one
donating and one accepting, However, the results obtained
show discrepancies with structures based on molecular
dynamics simulations.
The technique was also employed to study the energetics of
hydrogen network rearrangements in liquid water.
30
It was
claimed that the temperature dependence of the oxygen K-edge
fine structure can be used to determine an energy value for the
rearrangement of fully coordinated (ice like) and distorted
(broken donor) local hydrogen bonding configurations. The
authors observed a strong temperature dependence of oxygen
K-edge X-ray absorption fine structure features for super-
cooled and normal liquid water droplets prepared from the
break-up of a liquid microjet. Data was analysed over the
temperature range from222 uC to +15 uC. This yielded a value
of 1.5 0.5 kilocalories per mole for the average thermal
energy required to effect an observable rearrangement between
the fully coordinated (ice-like) and distorted (broken-
donor) local hydrogen-bonding configurations. The latter
were assigned to the pre-edge and post-edge features in the
measured XAS spectra, respectively. The conclusions, how-
ever, led to some controversy,
31
because they contradict some
of the results reported in ref. 29.
Nilsson et al. have very recently published a further study
reiterating that X-ray absorption spectroscopy can be used as a
very sensitive probe of the local bonding of water.
32
Realizing
that their recent results, which indicated that the hydrogen
bond network in liquid water consists mainly of water
molecules with only two strong hydrogen bonds, are con-
troversial they compared X-ray absorption spectra of liquid
water recorded with five very different techniques sensitive to
the local environment of the absorbing molecule, including
AEY, PEY and FY. They conclude that X-ray absorption
spectroscopy can be applied reliably to study the local bonding
of the water molecule and thus to reveal the nature of
hydrogen bonding in bulk water.
3.4 Microscopy
With synchrotron sources of ever higher brilliance being
developed, the intensity obtained from small spots on the
surface upon radiation can be sufficient to acquire a reason-
able signal. In consequence, a mapping of electronic and
structural properties with high lateral resolution has become
possible.
NEXAFS microscopy can be performed in transmission
(requiring a very thin sample) or in reflection mode. Since thin
films on substrates are generally not transparent only the latter
will be described here. For a description of experiments carried
out in transmission, the reader is referred to the literature, e.g.
ref. 33, which also describes some of the technical aspects
involved with high resolution mapping, such as instrumenta-
tion and acquisition protocols.
NEXAFS microscopy is increasingly employed for the
analysis of heterogeneous natural and synthetic polymeric
systems, such as engineered polymers, multilayers, latexes, and
bio-polymers. This is because of its ability to probe the
chemical complexity of the constituents at a relevant spatial
scale. Some of the problems in polymer science which require
detailed chemical analysis at a submicron scale are phase
segregation, determination of the morphology and interface
chemistry of blends and co-polymer systems, nano-patterned
structures, and self-assembly.
Spatial resolution can be achieved by focusing the X-ray
beam to a small spot in connection with scanning, or by using
a detector with high resolution. In the latter case, focusing
of X-rays is unnecessary. Spatial resolution in the electron
yield modes can be achieved by employing a photoemission
electron microscope (PEEM) as detector.
34
In this case, the
PEEM acts as a low-pass energy filter with a few eV
bandwidth. In connection with synchrotron radiation, the
technique is often abbreviated as X-PEEM. The technique
uses parallel image acquisition and has the potential to
reach 1 nm spatial resolution.
34
Because parallel data
acquisition is employed, the method is inherently fast and
allows the study of processes at video rates. Note that contrast
in X-PEEM is caused by several factors, including topography
and illumination, in addition to the chemical composition of
the material.
A recent example of a successful application of the technique
is the mapping of the molecular orientation of pentacene on a
patterned surface.
35
The orientation of pentacene films on a
surface patterned with SAMs of differently terminated thiols
(carboxyl, methyl, aromatic) was studied. The surfactants were
used to control the orientation of the pentacene, which was
thermally deposited on top of them. NEXAFS spectroscopy,
in connection with high resolution imaging, revealed that the
different thiols induced a perpendicular alignment of the
pentacene, in contrast to the bare Au surface where a parallel
alignment was observed.
A further example is the investigation of the selective
adsorption of proteins on polymer surfaces.
36
The authors
This journal is The Royal Society of Chemistry 2006 Chem. Soc. Rev., 2006, 35, 12441255 | 1253
employed X-PEEM in the C 1s, N 1s and O 1s regions to
characterize a phase-segregated polystyrene/polymethylmetha-
crylate (PS/PMMA) polymer thin film, and mapped the
adsorption of fibrinogen on the surface from buffered and
unbuffered aqueous solutions at different protein concentra-
tions (Fig. 9).
At low concentrations (,0.1 mg ml
21
) of the buffered
solution, adsorption of fibrinogen occurred with strong
preference for PS domains. In contrast, adsorption from
similar concentrations of unbuffered solution showed a strong
preference for the interface of the PS and PMMA domains.
Increasing the solution concentration up to 1 mg ml
21
of both
buffered and unbuffered solutions led progressively to a full
surface coverage (close-packed monolayer).
The authors emphasize that the results obtained clearly
demonstrate that X-PEEM with tunable soft X-rays has the
sensitivity to locate and detect adsorbed proteins at the
submonolayer level. Simultaneously, the spatial distribution
of phases, and protein distribution relative to the phases, can
be detected at the surface of an underlying microphase-
separated polymer substrate.
The power of NEXAFS microscopy in comparison to
other microscopies with chemical information, such as IR,
NMR or Raman, is based on its ability to exceed the spatial
resolution of these other techniques. Microscopy with a
resolution better than 50 nm has been achieved and a
resolution down to 1 nm appears realistic. In general,
sensitivity to specific species or functional groups is higher
using other techniques such as IR, NMR or Raman. However,
if a surface is chemically heterogeneous and this
heterogeneity is to be imaged, X-PEEM is, in many cases,
the best method.
4. Outlook
The present article can only cover a fraction of all the work
published on the topic. It is intended to give a flavor of the
strength and breadth of the technique and should inspire the
reader to study the literature for more detailed information on
specific topics.
The technique has developed significantly since it was first
established at the beginning of the 1980s. NEXAFS is
particularly strong in extracting orientational information in
parallel with information on electronic structure. The most
recent developmentsnamely the application of the technique
to liquids and to molecules in liquid environments, as well as
the imaging of electronic and structural properties with high
spatial resolutionwill play a key role in future applications.
The Life Sciences, Biology, and Materials Sciences will clearly
benefit enormously from these developments. Concentrations
of species in liquids below 1 mM appear realistic to give
sufficient signal in the near future, a concentration range
relevant for many biological processes. With synchrotron
sources of ever higher brilliance, a mapping of the electronic
and structural properties with a lateral resolution of a few nm
is possible. The number of studies dealing with X-PEEM
applied to thin organic films is still low. Organic samples can
be quite challenging due to charging and their susceptibility to
degrade when irradiated (radiation damage). Nevertheless the
technique bears a great potential for applications in the Life
Sciences, Medicine and Biology, and certainly has a bright
future lying ahead of it. The combination of high chemical
sensitivity and spatial resolution assure this type of spectro-
scopy an important place in the analytical tool box of the
surface scientist.
Fig. 9 (a) Color composite map (top) (red: PS; green: PMMA; blue: Fibrinogen (Fg)) and high-PS, high-PMMA and high-Fg spectra derived
from a C 1s image sequence recorded for 0.05 mg ml
21
Fg(water) (bottom). The inset map in the spectral plot indicates the region from which the
spectrum was extracted, identified by threshold masking the component maps. (b) Same for N 1s image sequence. In this case, only a two-
component fit was carried out (green: PS and PMMA; blue: Fg). (c) Same for O 1s image sequence. The image sequences were collected over three
different regions of the sample which is why the domain patterns differ for each core edge study. (Reprinted with permission from ref. 36. Copyright
(2004) Elsevier).
1254 | Chem. Soc. Rev., 2006, 35, 12441255 This journal is The Royal Society of Chemistry 2006
Acknowledgements
I thank Dr C. Baddeley for reading the manuscript.
References
1 http://xdb.lbl.gov/Section2/Sec_2-2.html.
2 J. Sto hr, NEXAFS Spectroscopy, Springer, Berlin, 1992.
3 http://xdb.lbl.gov/Section2/Sec_2-1.html.
4 H. Winick, in Synchrotron Radiation Research, ed. H Winick and
S Doniach, Plenum Press, New York, 1980.
5 G. Ertl and J. Ku ppers, Low Energy Electrons and Surface
Chemistry, VCH, Weinheim, 1985.
6 A. S. Dawydow, Quantenmechanik, VEB Deutscher Verlag der
Wissenschaften, Berlin, 6th edn,1981, p. 422.
7 K. Weiss, P. S. Bagus and C. Wo ll, Rydberg transitions in X-ray
absorption spectroscopy of alkanes: The importance of matrix
effects, J. Chem. Phys., 1999, 111(15), 68346845.
8 S. G. Urquhart and R. Gillies, Rydberg-Valence mixing in the
carbon 1s near-edge X-ray absorption fine structure spectra of
gaseous alkanes, J. Phys. Chem. A, 2005, 109(10), 21512159.
9 J. J. Rehr and R. C. Albers, Theoretical approaches to X-ray
absorption fine structure, Rev. Mod. Phys., 2000, 73(3), 621654.
10 B. Ravel, A practical introduction to multiple scattering theory,
J. lloys Compd., 2005, 401, 118126.
11 J. L. Solomon, R. J. Madix and J. Sto hr, Orientation and absolute
coverage of benzene, aniline, and phenol on Ag(110) determined by
NEXAFS and XPS, Surf. Sci., 1991, 255, 1230.
12 D. L. Allara and R. G. Nuzzo, Spontaneously Organized
Molecular Assemblies. 2. Quantitative Infrared Spectroscopic
Determination of Equilibrium Structures of Solution-Adsorbed
n-Alkanoic Acids on an Oxidized Aluminum Surface, Langmuir,
1985, 1, 5266.
13 J. Sto hr, K. Baberschke, R. Jaeger, R. Treichler and S. Brennan,
Orientation of chemisorbed molecules from surface-absorption
fine-structure measurements CO and NO on Ni(100), Phys. Rev.
Lett., 1981, 47(5), 381384.
14 G. Ha hner, A. Marti, W. R. Caseri and N. D. Spencer,
Orientation and Electronic Structure of Methylene Blue on
Mica: A Near Edge X-Ray Absorption Fine Structure
Spectroscopy Study, J. Chem. Phys., 1996, 104(19), 77497757.
15 G. Ha hner, R. Hofer and I. Klingenfuss, Order and Orientation in
Self-Assembled Long Chain Alkanephosphate Monolayers
Adsorbed on Metal Oxide Substrates, Langmuir, 2001, 17,
70477052.
16 G. Ha hner, M. Zwahlen and W. Caseri, Chain Length
Dependence of the Conformational Order in Self-Assembled
Dialkylammonium Monolayers on Mica Studied by Soft X-Ray
Absorption, Langmuir, 2005, 21, 14241427.
17 Y. Zubavichus, M. Zharnikov, Y. J. Yang, O. Fuchs, E. Umbach,
C. Heske, A. Ulman and M. Grunze, X-ray photoelectron
spectroscopy and near-edge X-ray absorption fine structure study
of water adsorption on pyridine-terminated thiolate self-assembled
monolayers, Langmuir, 2004, 20(25), 1102211029.
18 K. E. Nelson, L. Gamble, L. S. Jung, M. S. Boeckl, E. Naeemi,
S. L. Golledge, T. Sasaki, D. G. Castner, C. T. Campbell and
P. S. Stayton, Surface characterization of mixed self-assembled
monolayers designed for streptavidin immobilization, Langmuir,
2001, 17(9), 28072816.
19 http://www.physics.ncsu.edu/stxm/polymerspectro/.
20 O. Dhez, H. Ade and S. G. Urquhart, Calibrated NEXAFS
spectra of some common polymers, J. Electron Spectrosc. Relat.
Phenom., 2003, 128(1), 8596.
21 H. Ade and S. G. Urquhart, NEXAFS spectroscopy and
microscopy of natural and synthetic polymers, in: Chemical
Applications of Synchrotron Radiation, ed. T. K. Sham, World
Scientific Publishing, Singapore, 2002.
22 A. Scho ll, R. Fink, E. Umbach, G. E. Mitchell, S. G. Urquhart and
H. Ade, Towards a detailed understanding of the NEXAFS
spectra of bulk polyethylene copolymers and related alkanes,
Chem. Phys. Lett., 2003, 370, 834841.
23 J. Boese, A. Osanna, C. Jacobson and J. Kirz, Carbon edge
XANES spectroscopy of amino acids and peptides, J. Electron
Spectrosc. Relat. Phenom., 1997, 85, 915.
24 C. Carravetta, O. Plashkevych and H. Agren, A theoretical study
of the near-edge X-ray absorption spectra of some larger amino
acids, J. Chem. Phys., 1998, 109(4), 14561464.
25 Y. Zubavichus, A. Shaporenko, M. Grunze and M. Zharnikov,
Innershell absorption spectroscopy of amino acids at all relevant
absorption edges, J. Phys. Chem. A, 2005, 109(32), 69987000.
26 S. G. Urquhart, A. P. Hitchcock, A. P. Smith, H. W. Ade, W. Lidy,
E. G. Rightor and G. E. Mitchell, NEXAFS spectromicroscopy of
polymers: overview and quantitative analysis of polyurethane
polymers, J. Electron Spectrosc. Relat. Phenom., 1999, 100,
119135Sp. Iss. SI.
27 L. J. Gamble, B. Ravel, D. A. Fischer and D. G. Castner, Surface
structure and orientation of PTFE films determined by experi-
mental and FEFF8-calculated NEXAFS spectra, Langmuir, 2002,
18(6), 21832189.
28 M. Freiwald, S. Cramm, W. Eberhardt and S. Eisebitt, Soft X-ray
absorption spectroscopy in liquid environments, J. Electron
Spectrosc. Relat. Phenom., 2004, 137140, 413416.
29 P. Wernet, D. Nordlund, U. Bergmann, M. Cavalleri, M. Odelius,
H. Ogasawara, L. A

. Na slund, T. K. Hirsch, L. Ojama e, P. Glatzel,

L. G. M. Pettersson and A. Nilsson, The Structure of the First
Coordination Shell in Liquid Water, Science, 2004, 304, 995999.
30 J. D. Smith, C. D. Cappa, K. R. Wilson, B. M. Messer, R. C. Cohen
and R. J. Saykally, Energetics of Hydrogen Bond Network
Rearrangements in Liquid Water, Science, 2004, 306, 851853.
31 A. Nilsson, P. Wernet, D. Nordlund, U. Bergmann, M. Cavalleri,
M. Odelius, H. Ogasawara, L. A. Na slund, T. K. Hirsch, P. Glatzel
and L. G. M. Pettersson, Comment on Energetics of hydrogen
bond network: Rearrangements in liquid water, Science, 2005,
308, 5723; J. D. Smith, C. D. Cappa, B. M. Messer, R. C. Cohen
and R. J. Saykally, Response to Comment on Energetics of
hydrogen bond network Rearrangements in liquid water, Science,
2005, 308, 5723.
32 L. A. Na slund, J. Luning, Y. Ufuktepe, H. Ogasawara, P. Wernet,
U. Bergmann, L. G. M. Pettersson and A. Nilsson, X-ray
absorption spectroscopy measurements of liquid water, J. Phys.
Chem. B, 2005, 109(28), 1383513839.
33 A. P. Hitchcock, C. Morin, X. R. Zhang, T. Araki, J. Dynes,
H. Stover, J. Brash, J. R. Lawrence and G. G. Leppard, Soft
X-ray spectromicroscopy of biological and synthetic polymer
systems, J. Electron Spectrosc. Relat. Phenom., 2005, 144,
259269Sp. Iss. SI.
34 E. Bauer, Photoelectron microscopy, J. Phys.: Condens. Matter,
2001, 13, 1139111404.
35 Y. J. Hsu, W. S. Hu, D. H. Wei, Y. S. Wu and Y. T. Yao,
Mapping molecular orientation of pentacene on patterned Au
surface, J. Electron Spectrosc. Relat. Phenom., 2005, 144,
401404Sp. Iss. SI.
36 C. Morin, A. P. Hitchcock, R. M. Cornelius, J. L. Brash,
S. G. Urquhart, A. Scholl and A. Doran, Selective adsorption of
protein on polymer surfaces studied by soft X-ray photoemission
electron microscopy, J. Electron Spectrosc. Relat. Phenom., 2004,
137140, 785794Sp. Iss. SI.
This journal is The Royal Society of Chemistry 2006 Chem. Soc. Rev., 2006, 35, 12441255 | 1255