External Prestressing, Bavarian Examples

Konrad Zilch , Richard Buba

Abstract: External prestressing gets more and more important as a method for bridges.
During the last years it has evolved from the status of pilot application to a standard
design method for box girder bridges in Germany. The development will be shown using
bavarian examples.
1. The Development in Review
The first bridge world-wide with external prestressing was built in Aue, Saxony from
1935 to 1937 according to a concept of Dischinger (DRP 727429). It was a haunched
beam with three spans (25.2 m - 69.0 m - 23.4 m) with a drop-in girder in the middle
span. Suspended no-bond tendons running outside the concrete cross-section were used.
A short time later, from 1938 to 1943, the Knockestrand bridge (40.5 m - 71.5 m - 40.5
m) in Sweden was built with external prestressing, too.
After Second World War the development of bridge structures in Germany was
concentrated on internally post-tensioned systems. Howeever, external prestressing was
applied by Magnel in Belgium and to some bridges in France. Where as in Garmany the
corrosion resistance of external tendons was considered to be insufficient at the time.
Post-tensioned bridges with internal tendons appeared as unproblematic and only this
method was further developed and applied. Nevertheless, the corrosion protection
system were improved and beginning in the mid 80s, external prestressing emerged as an
alternative to conventional internal prestressing, first for special purposes, e.g. streng
thenings, and later as a general method with regard to durability and maintenance. Some
pilot projects were executed. The bridge Ruderting in Bavaria was one of these. This
construction method was very successful. The good experiences with the external
prestressing in construction of bridges and the benefits in maintenance were the main
reason that the external prestressing will be set up as a standard design method for box
girder bridges.
2. Technology
2.1 Layout of Tendons
In principle two deferent layouts of the external prestressing tendons can be chosen.
1. Deflected tendons
The tendons are deflected over the columns as well as in the spans, e.g. at mid-spans
(Fig. 1a). Deflection saddles must be used in this case. The deflection saddles must have
a relatively high precision, therefore often precast concrete or steel units are used. Only
light cross girders are necessary for bearing the deflection saddles.
2. Straight tendons
The tendons are running straight and eccentric between span cross girders. Two cross
girders or other anchorage systems are necessary in any span to anchor the tendon forces
(Fig. 1b).
Fig.1: Possibilities for layout of tendons
a) Deflected tendons b) Straight tendons
2.2 Construction Methods
As construction methods span-by-span implementation with falsework or scaffold
carriage as well as incremental launching were used in the pilot projects.
Dependent upon the construction method the tendon layout may be chosen.
straight or deflected
combination of both
altering tendons partial rebuilding from centric straight to deflected shape (for
example by applying the incremental launching technique)
furthermore mixed internal and external prestressing in combination is possible
(incremental lauching)
The external prestressing offers the following variations of implementation (Fig.2).
Structural possibilities
Incremental Falsework
launching
Straight Deflected Straight
kabelu tendoms tendoms tendoms
external prestressing Combination of
only external and internal
prestressing
Change from straight
to deflected tendoms
possible
Fig. 2: Possibilities of implementation
2.3 External Prestressing Systems
At the at the moment several external prestressing systems are approved by the building
authorities and on the market in Germany. In addition almost any producer is developing
new systems and it is expected that the variety on the market will be extend.
Some systems are shown in figure 3.
Fig. 3: Types of external tendons
3. Pilotprojekt Ruderting
In 1994, the valley bridge Ruderting, on route 85 from Passau to Cham, was designed as
a Bavarian pilot project using external prestressing. This bridge has 6 spans - 36 m -
4x45m - 36m (Fig. 4), and crosses the valley Haselbachtal at a height of approximately
43 m. The straight routing and light curvature of the gradient offer the optimal
requirements for the use of external prestressing.
A detailed invitation to bid was prepared by the highway administration in Passau, with
co-operation from the author. A box section was chosen for the superstructure, with
height of 2.7 m and regular span of 45.0 m (slenderness = 1/16.7). Partial pre-stressing
was planned.
Fig.4: Talbrcke Ruderting - length section
No construction method was specified in the plans. The 252 m long bridge could be
implemented with falsework or with incremental launching. Therefore, both possibilities
were pre-investigated and included in the plans.
No concrete pre-stressing system was specified. However, all prestressing systems
should be approved by the appropriate regulatory authority, or at least be in preparation
for this end.
The draft by the highway administration was advertised Europe-wide. Alternative bids
were allowed under the following conditions:
no change in spans and overall length
Slenderness of superstructure h/L 1/16
The tendons must be exchangeable under the full traffic load of bridge class 30/30
announcement of failure through crack formation
possibility of an increase in traffic load by 20% through structural provisions for 4
additional tendons
no transverse prestressing
The technology of implementation could be free chosen through calculations and
construction management in the design process.
It should be mentioned, however, that at the moment the price is very high per ton of the
external tendons, due to the small number of existing applications of external pre-
stressing. As prices were approximate three times higher than the internal pre-stressing
steel, it is necessary to devise simple construction elements and as little tonnage of pre-
stressing steel as possible.
The provided partial pre-stressing gives the engineer more freedom of choice in
structural materials for shielding the tensile force. Prestressing steel and conventional
steel are the two possibilities, with the present price differences leaning toward the use of
typical reinforcement steel.
Initially, 9 bidders submitted 9 main offers and 12 secondary offers.
On analysing the offers, a special offer 1 from the company Bilfinger & Berger Bau AG
was the most economical and so obtained the contract.
The special offer chose straight tendons for pre-stressing of the 2.60 m high box girder.
Fig.5 : Layout of tendons
About 2/3 of tendons were eccentric. They ran along the bottom of the spans and above
over the columns (Fig. 5). The anchoring of these tendons was done in the opening of
the span cross girders, which were placed 8 m in front and behind of the column cross
girders. The remaining tendons were placed at the centroid of the cross-sectional area
and are only anchored in the final state in the end cross girders. Due to the slight sag of
the bridge, the continuous, coupled tendons had be deflected at two saddles.
The construction of the superstructure followed in three sections on falsework.
The cross girder and tendons are shown in Fig. 6
Fig.6 : Cross girder with tendons
4. Standard Design Method
Because of the good experience gathered by the pilot project and the advantages of
external prestressing the road administration made a decision to introduce this
prestressing method as a standard design method for bridges with box girders. The
administration expects the following advantages, especially with regard to durability and
maintenance:
the tendons are easy controllable and verifiable
they are exchangeable
they can be subjected to a secondary tensioning (re-stressing)
they have a high-quality, industrial corrosion resistance
the stress from traffic vibration is small
partial prestressing can be utilized for economic construction, exhibiting ductile
behaviour equivalent to a larger quantity of conventional reinforcing
the web of the superstructure is free of tendons, making placing of the concrete
easier
The construction site is less weather dependent because no cement injection of
tendons is necessary
In Germany a code for the prestressing with external tendons is not introduced by the
building administration. Therefore the road administration has invited experts to
formulate regulations which are based on the experience of the undertaken pilot projects.
For further structures the following regulations have to be used:
- limit state of decompression

c x ,
( / ) . G, P(t), Q
k
3 0 0

c x ,
axial concrete stress
G dead load of the structure
P(t) value of prestressing force at time t including loss of prestress due
to creep, shrinkage and relaxtion
Q
k
road traffic load according to the model of DIN 1072
- limit state of tensile stresses in concrete during construction

c
( ) . G, P(t), Q N / mm fr B 35 30

c
( ) . G, P(t), Q N / mm fr B 45 35

c
concrete stress in the extreme fibre of the section
G dead load of the structure
P(t) value of prestressing force at time t including loss of prestress due
to creep, shrinkage and relaxtion
Q variable actions according (snow, wind, settlement )
- limit state of tensile stresses in concrete in transverse direction

c
( ) . G, P(t), Q N / mm fr B 35 4 0

c
( ) . G, P(t), Q N / mm fr B 45 50

c
concrete stress in the extreme fibre of the section
G dead load of the structure
P(t) value of prestressing force in transvers direction at time t including
loss of prestress due to creep, shrinkage and relaxation
Q variable actions (snow, wind, traffic )
- limit state of steel stresses
stresses at tensioning

po ptk po ptk
f f
,max ,max
. . = = 085 0 75 or whichever is lesser
stresses immediately after tensioning

po ptk po ptk
f f
,max ,max
. . = = 080 070 or whichever is lesser
- limit state of cracking
The minimum reinforcement is provided according to DIN 4227-1
- ultimate limit state of fatigue
Crack width is controlled according to DIN 4227
- ultimate limit state
175
125
1 75
10
15
.
.
,
.
.

+ +

G Q P R
- shear
For the limit state of serviceability no analysis of the stresses is necessary. In ultimate
state the analysis has to be undertaken according to DIN 4227 -1.
In the addition regulation contains some detailing constructions rules for the anchorages,
deviators size of tendons and provisions for fixing additional tendons..
5. New Bavarian Bridges - Standard Construction Method
After introducing of external prestressing as a standard design method five new bridges
are built or designed in Bavaria. They are listed in the Tab.1.
Name Road Spans Alignment Implementation Method +
Trajectory of tendon
Ruderting (finished) B 85 36+4x45+36 = 252 m straight falsework
Hllthalbrcke St 2116 35+43+50+43+35= 206
m
straight falsework
Talbrcke
Mnchberg
A9 44.25+7x52+44+42.25=
= 496.50 m
straight incremental lauching
internal straight +
external deflected tendons
Talbrcke Trockau A9 51+55+60+85+100+85+
60+55+51= 602 m
double bend scaffold carriage
straight + deflected tendons
Naabtalbrcke A6 39.5 + 7x48.5 + 41.5 +
37.0= 457.5 m
circle R=1800 m incremental laucing
Schilternbachtal-
brcke
A6 41.6+2x52.0+41.6=
= 187.2 m
circle R=2200m falsework
Tab.1: Bavarian bridges with external pre-stressing
The Hllthalbrcke (Fig.7) is now under construction. The conditions of the bid were
similar to the Ruderting bridge. The offer from the company DYWIDAG AG was the
most economical. The superstructure is a single box girder with high of 3.0 m, the
slenderness of the middle span h / L = 1/16.7 (Fig.8).
The tendons are straight and the span-by-span implementation method with falsework
was chosen.
Fig.7 : View on the Hllthalbrcke
Fig.8 : Hllthalbrcke: superstructure cross-section in the span, view of pier
The superstructures of the other new bridges are still in the state of planing and design.
The length and alignment of the bridges give good conditions to application of different
technologies and implementation methods. Both the external pre-stressing only and the
combination of external and internal prestressing will be applied. The straight and
deflected layout of tendons as well as their combination will be used.
The different possible construction methods are planned. The incremental lauching as
well as span-by-span with falsework and scaffold carriage will be applied.
Therefore, interesting structures are expected.
The variety of the bridge buildings shows that the external pre-stressing is able to fulfil
the same requirements as the traditional internal prestressing and sets no limitations for
the design.
6. References
[1] Dischinger, F.: Entwicklungen und Fortschritte im Eisenbeton. In: Neues Bauen im
Eisenbeton. Deutscher Beton-Verein E.V. 1937, pp. 7 - 37.
[2] Eibl, J.: Brcken mit externer Vorspannung: Deutscher Beton-Verein E.V.,
Vortrge Betontag 1989, pp. 259 - 273
[3] Vo, W.: Alternativen zur konventionellen Vorspannung im Brckenbau; Deutscher
Beton-Verein E.V., Vortrge Betontag 1989, pp. 244 - 258
[4] Matthes, M.; Weber, J.; Zilch, K.: Talbrcke Ruderting - Eine sechsfeldrige
Brcke auf Lehrgerst mit externer Vorspannung. Vortrag auf dem Deutschen
Betontag 1997
[5] Metzler, H.; Schmitz, Chr.: Spannbetonbrcken mit externer Vorspannung -
Historischer Rckblick und Erfahrungen einer Straenbauverwaltung. Bauingenieur,
Vol.73, Feb. 1998