-

+
DC12V
+
+
-
GND
+12V
-
+
DC12V
+
-
-
+
-
+
+
-
-
+
DC Power
RS485 TCP/IP

-
GND
+12V
GND
+12V
GND
+12V
-
+
Installation Guide for Color Display Serial
II. Access control system overview
RS232/RS485
Converter
Card
reader
Release
button
Alarm
Lock Door
sensor

Warning: Dont connect wires with power on!

III. Connect to door lock
1device and lock share power supply
NC lock
NO lock
Notice:If locks working power is DC12V,
and working current is least 1000mAless
than that of access control device power
supply, wiring with sharing power supply
can be adopted.
Notice: Wiring with lock power supplied
independently is recommended for the
following states:
1) Locks working power is DC 12V,
powers current is device not 1A more
than that of lock.
2)Locks standard voltage is not DC12V.
3)The distance between lock and device
is long.
NO lock
NC lock
. Connection with other device
NC Alarm
Alarm
Power
Release
button
Door sensor
2device and lock dont share power supply
DC Power
DC Power DC Power
Access control device can be connected with external out-go
switch, which provides convenience to open door from the inside.
When a registered person verified, the access control device
will export signal to open the door.
Door sensor will detect on-off state to sense whether the door
is opened by accident or the door is not closed well, alarm will

If access control device is torn down illegally, or door sensor
is abnormal, or menace alarm gives off, the device will export
Connect a Weigand reader to work as a controller.
Access control software to manage multi devices via RS485
Access control system
alarm signal.
or TCP/IP.
The device could connect to NC or NO locks, the connection terminal is not same, please according to the following
diagram to make connection.

be given off under abnormal condition.
Notice:
+
-
FR 107
+
-
FR 107
+
-
FR 107
+
-
FR 107
NC 1
COM 1
NO 1
BUT
GND
SEN
NC 2
COM 2
NO 2
NC 1
COM 1
NO 1
BUT
GND
SEN
NC 2
COM 2
NO 2
NC 1
COM 1
NO 1
BUT
GND
SEN
NC 2
COM 2
NO 2
NC 1
COM 1
NO 1
BUT
GND
SEN
NC 2
COM 2
NO 2
I. Install device
1)Post the mounting template on
the wall. Drill holes according to
the marks on the template.(Holes
for screw and wiring)
3) Take away the screw on
the bottom of device
2)Take off the water-proof cushion
5)Fix the cushion and plate on
the wall
4) Release the mounting plate
6) Fix the device with the plate
after all wiring completed
15 16 17 16
10
11
12
13
Mounting Paper(only for your reference)
line hole
Note: This installation figure is a sample. The other device prevail in kind and could be refer to it.
Ground
Connect to the wired doorbell.

Doorbell
%

BUT
Prevention of statical electricity.

Doorbell
-
+
NC 1
COM 1
NO 1
BUT
GND
SEN
NC 2
COM 2
NO 2

BUT
GND
BELL+
BELL-
RXD
485+
WD 1
GND
485-
TXD
WD 0
%
-
+
NC 1
COM 1
NO 1
BUT
GND
SEN
NC 2
COM 2
NO 2
NO Alarm
Alarm Power
NC2
COM2
NO2
NC1
COM1
NO1
BUT
GND
SEN
-
+
AC220V
DC 24V
Alarm
Device alarm exports an open-close signal. The alarm can be serially connected to power circuit of simple alar
in left picture). It can also be used as touch signal of advanced alarm/monitor system (as shown in right picture).The rating
output of the alarm no more than DC12V.There are two kinds of connection for the alarm: NC alarm and NO alarm (as sho-
wn in left picture).
m (as shown
24VAC relay
Access Control

Connect with access controller, and communicate via

Wiegand signal.
Notice:Please use the attached diode which used in the above diagram with the model as FR107. And please don't
connect the poles in reverse.
TXD
BELL+
BELL-
RXD
GND
485+
WD 0
WD 1
GND
485-
TXD
BELL+
BELL-
RXD
GND
485+
WD 0
WD 1
GND
485-
8) Equipment needed to connect access control software to register users.
1) reset
2RS485
3TCP/IP

485A
485B
485A 485B
485A 485B 485A 485B
PC

VIII. Device communication

1RS232
RS485 converter
RS232 bus
RS485 bus
PC
serial port
TXD Pin2-Txd
RXD Pin3-Rxd
GND Pin5-Gnd
485+
485-
Terminal definition
Terminal number PC serial port
Terminal number PC serial port
RS485 communication+
RS485 communication-
Warning: Dont connect wires with power on!
Mask255.255.255.0
IP192.168.1.100
IP192.168.1.124
Mask255.255.255.0



1

<>

3


2

<>

6


3

<>

1


6

<>

2


Joint 1 Joint 2 Pin Pin
TX+
TX -
RX+
RX-
RX+
RX-
TX+
TX -

Cable order Pin Color Pin Cable order







TX+ < > 1
TX- 2 <
RX+ < > 3
4 <
5 < > 5
RX- 6 < > 6
7 < > 7
8 < > 8
white-orange
3
1
orange
white-green
blue
white-blue
green
white-brown
brown
> 2
> 4
TX+
TX -
RX+
RX-
. Other function
Front
Side
If wrong operation or other unexpected fault
makes device fail in working normally, use
this function to restart the device.
. Notice



Find a top pointed
tool with diameter
of 2mm.
1Connection between device to PC via cross cable.
2Lan connection
Switch
Manual reset
1)Make sure all connection is correct before power on the device or not wiring when the device is powered.
2)DC12V/3A power adaptor is recommended to power the device, You can consult technicians for detailed information.
3)Please read wiring instruction carefully, damage casued by abnormal operation is beyond maintenance guarantee.


5)To prevent machine damage caused by too powerful instant static in winter or in the place where there is much
static, please connect ground wire firstly, then connect other wires.
6)If the distance between power supply and machine is long, please dont use network cable or other wires.While
selecting wire for power supply, voltage attenuation caused by too long distance transmission should be taken

7)While using RS485 communication method for network deployment, RS485 cable and RS232/485 converter required, bus
structure is recommended. If RS485 communication distance is over 100 meters, add a terminal-matched resistor
Please install the device according to this guide, we are not responsible for such damage caused by any abnormal operation.
account.
(with 120) to RS485 bus.
4)Make sure there is no bare part of the connection terminal.






DATA0
DATA1
GND
+12V
IWD 0
IWD 1
GND
BEEP
GLED
RLED
+12V
GLED
RLED
BEEP
. Wiegand output connection
Wiegand 26output interface, export the verified user
number or card number to the controller.
Wiegand 26input interface to connect a Wiegand reader, the
device works as a controller to verify the information sent
from the wiegand reader.
Reader and access control can be installed both inside and
outside the door and control the lock and out & in together.
VII. Wiegand input connection
DATA0
DATA1
GND
.Power connection
The devices working voltage is DC12V, with
working current 500mA,standby current 50mA.
Make sure the connection as the diagram(Dont
connect the poles in reverse.).
-
+
DC12V
GND
+12V
Note:
1) The distance between device and access controller or card reader shouldnt be over 90 meters (If a longer distance
is needed or there is interference in using environment, please use Wiegand signal delay.).
2) To ensure the stability of the Wiegand signal, the device must share the GND with controller or Weigand reader.
3) If the distance of Wiegand output or 485 communication is over 90 meters, in order to reduce the interference caused
by the long distance, it is suggested to use the cable with shield and connect the shield cable to the SGND terminal.