Scribd
Upload
148 views

Print Server & Event Logger Setup

The document provides steps to configure a print server and add a printer. It involves setting the print server IP address, configuring the server name and port name, assigning the IP address, and then adding the printer by entering the server IP and port name. It also describes configuring the event logger software maxDNA to use the printer by setting the print port and state and entering the printer name in the registry.

Uploaded by

Deepak Gupta
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
148 views

Print Server & Event Logger Setup

The document provides steps to configure a print server and add a printer. It involves setting the print server IP address, configuring the server name and port name, assigning the IP address, and then adding the printer by entering the server IP and port name. It also describes configuring the event logger software maxDNA to use the printer by setting the print port and state and entering the printer name in the registry.

Uploaded by

Deepak Gupta
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 12

CONFIGURING PRINT SERVER

STEP1: THIS IS REQUIRED TO BE DONE,IF THE PRINT SERVER ADDRESS IS BEING SET FOR THE FIRST TIME OR PRINT SERVER ADDRESS HAS BEEN RESET. FOR PARLI, THE PRINT SERVER ADDRESSES HAD ALREADY BEEN SET AT EDN. THE ADDRESSES SET WERE:

172.16.160.50 & 172.17.160.50.


Go to My NETWORK PLACES (Icon can be on desktop or you can find it in control panel. Right click and click on properties). Next Select any one of the LAN Cards and right click on it. Click on Properties. In the List Box "THIS CONNECTION USES THE FOLLOWING ITEMS" scroll down the menu and select the last option "INTERNET PROTOCOL(TCP/IP)" ,the properties tab will be highlighted, then click on properties tab. From there note down the IP address set in the computer and replace it with 192.168.0.10 and click on "OK" then on "CLOSE". (To be done if Print Server address setting is being done for the first time). STEP2: Now open the web browser and type http://192.168.0.10 in the address box, and press Enter.

Now the print server Dialog box appears as above.

KKJ

Page 1 of 122

STEP3: Now click on system->Configuration

Now in the box "SERVER NAME" put name of the printer "_LOG_PS_DMP1" (Example). IMP: name of the printer should always be preceded by _LOG after that you can give any name. In the box "PORTNAME" put the name "PS-DMP1-P1" (Example) Note down both SERVER NAME & PORTNAME STEP4: In the IP address Field IP Address: 172.16.160.50 (Example) it is the IP address you want to assign to Printer Subnet Mask: 255.255.0.0 Default Gateway: 0.0.0.0 Click on Apply

KKJ

Page 2 of 122

STEP5: Go to My NETWORK PLACES, Do Right click and click on properties. Below the line " THIS CONNECTION USES THE FOLLOWING ITEMS" scroll menu is there, select the last option "INTERNET PROTOCOL(TCP/IP)" ,the properties tab will be highlighted then click on properties tab. Replace the previous IP address [192.168.0.10] with the original IP address you noted in STEP1. Click on "OK" then on "CLOSE".

KKJ

Page 3 of 122

CONFIGURING/ADDING PRINTER
STEP1: Go to START->SETTINGS->PRINTERS AND FAXES

Click on Add a printer STEP2:

Click on NEXT

KKJ

Page 4 of 122

KKJ

Page 5 of 122

Here in IP Address Field put the IP Address same as given in STEP4 of CONFIGURING THE PRINT SERVER.

Click on Custom ->Settings

KKJ

Page 6 of 122

In Protocol field Click on LPR and in Queue Name enter the port name noted in STEP3 of CONFIGURING THE PRINT SERVER.(PS-DMP1-P1) Click on OK then NEXT

Click on FINISH

KKJ

Page 7 of 122

Highlight the printer, as shown. If the desired printer is not on the list, click Have Disk and insert the printer driver disk that came with your printer to install the printer drivers

Click on Browse->Select CD Drive(Z:\)->double click on Win_Drvr folder->select WINXP folder and double click on that

Click on open
KKJ Page 8 of 122

Click on OK

Select the Printer out of the list and Click on NEXT

KKJ

Page 9 of 122

Enter the Printer name same as given for Server Name in STEP3 of CONFIGURING THE PRINT SERVER (_LOG_PS_DMP1), Select YES and Click on NEXT. In next step share the printer and give the share name as the name of the printer i.e _LOG_PS_DMP1 (Example).

Click NEXT

Click on NEXT

KKJ

Page 10 of 122

Click on YES to check printer is rightly setup. Click on NEXT.

Click on FINISH and the printer Installation is over.

KKJ

Page 11 of 122

CONFIGURING maxDNA FOR PRINTING


Do these changes on computer which is configured as EVENT LOGGER i.e OPSTN5 and OPSTN6 (It can be any other computer). STEP1: Go to C:\Custom\Sbp Open EvtLogger.ini file, In that file do the following changes

Printport=LPT2: PrintState=ON

Instead of LPT2 we can use any other port like LPT3, LPT4, LPT5 etc but not LPT1. STEP2: Go to C:\Custom\Sbp Open Events.ini file, In that file do the following changes

PrintState=ON File Enable=ON

STEP3: Go to START->PROGRAMS->maxDNA->UTILITIES->MCS REGISTRY EDIT

In MACHINE SETTINGS select LPT port which you have defined in STEP1 of EvtLogger.ini file as i.e LPT2: In that enter the name of the printer _LOG_PS_DMP1. Now Restart the maxSTATION, this completes the maxDNA Printer configuration.
KKJ Page 12 of 122

You might also like