Scribd
Upload
336 views

IBM DB2 9.7 Run Time Client Notes

The document provides instructions for downloading, installing, and configuring the IBM DB2 Data Server Runtime Client. It explains that users must download the 32-bit client file, install it as an administrator, and then configure an ODBC connection to access the Datamart database called SFMSP using their username and password.

Uploaded by

Miki Arsovski
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
336 views

IBM DB2 9.7 Run Time Client Notes

The document provides instructions for downloading, installing, and configuring the IBM DB2 Data Server Runtime Client. It explains that users must download the 32-bit client file, install it as an administrator, and then configure an ODBC connection to access the Datamart database called SFMSP using their username and password.

Uploaded by

Miki Arsovski
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

Instructions to Download and Install the IBM DB2 Data Server Runtime Client

Download the IBM DB2 Data Server Runtime Client Access the Datamart website (http://dasapp.oregon.gov/datamart/) to download the latest IBM DB2 runtime client. Save the file to your local computer. All users: You must install the 32-bit (ex. V9.7fp4_nt32_rtcl_EN.exe) IBM DB2 data server runtime client because Hyperion is a 32-bit application; even if you are installing the application on a 64-bit Windows 7 machine. All users: You must install the IBM DB2 Data Server Runtime Client as an administrator.

Installing the IBM DB2 Data Server Client Double-click on the exe file you downloaded from our website to start the installation. An install shield wizard screen will appear and extract the files.

Last updated: 12/12/11

Page 1 of 8

DB2 setup screen will appear showing the version you are installing. Click Next to continue.

Select the I accept the terms in the license agreement radio button and then Next.

Last updated: 12/12/11

Page 2 of 8

Leave the Installation type as typical, and click on Next.

Click Install to confirm your choices and begin the software installation.

Last updated: 12/12/11

Page 3 of 8

The DB2 setup wizard will show the status of the install progress.

When complete it will show you the Setup is complete window. Click Finish.

Reboot your computer to complete the process and initialize the settings. Last updated: 12/12/11 Page 4 of 8

Setup ODBC Connection


32-bit users: Go to the ODBC Data Source Administrator by accessing the Control Panel, Administrative Tools, and Data Sources (ODBC). Windows 7 (64 bit) users: 1. Windows 7 Control Panel brings up the 64-bit ODBC Data Source Administrator; you must use the 32- bit ODBC Data Source Administrator; located under %WINDIR%\SYSWOW64, run as administrator: odbcad32.exe.

Click on System DSN tab and click the Add button,

Last updated: 12/12/11

Page 5 of 8

Scroll down and click on IBM DB2 ODBC DRIVER (or IBM DB2 ODBC DRIVER DB2COPY1)

Click Finish.

You will then see a blank ODBC IBM DB2 Driver Add window

Enter SFMSP, as the Data source name and click on Add and you should see the

following window:

Last updated: 12/12/11

Page 6 of 8

Click on the TCP/IP tab and fill out the boxes as shown below, then click the OK button.

Warning: Double-check for typos before pressing OK. The run-time client does not support being able to edit these entries after pressing OK. To remove a database entry you must uncatalog the current entry and then re-add it. To uncatalog a database entry for SFMSP:

o Click on Start, All Programs, IBM DB2, DB2Copy1, Command Line Tools, Command
Line Processor. This will open a window with the DB2 command prompt.

o Uncatalog db SFMSP, Enter o Quit, Enter, Exit, Enter will close the command prompt window.

Testing the Connection


While on the ODBC Data Source Administrator page and System DSN tab, you can test the

connection is working properly, by clicking on SFMSP and then clicking the Configure button. On the CLI/ODBC Settings SFMSP screen you enter your Datamart User ID and Password and press the connect button. If functioning properly, it should return with the following message:

Last updated: 12/12/11

Page 7 of 8

Last updated: 12/12/11

Page 8 of 8

You might also like