Scribd
Upload
1K views

How To Build An Arduino Powered 6DOF Motion Platfo

The document describes how to build a six degree of freedom (6DOF) motion platform powered by an Arduino microcontroller and six standard servo motors. It involves cutting acrylic parts on a laser cutter, assembling connecting links between the servos, wiring the servos to the Arduino, and programming the Arduino to control the motion of the platform. Step-by-step instructions are provided covering the cutting, assembly, wiring and programming needed to construct the motion platform.

Uploaded by

swonera
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
1K views

How To Build An Arduino Powered 6DOF Motion Platfo

The document describes how to build a six degree of freedom (6DOF) motion platform powered by an Arduino microcontroller and six standard servo motors. It involves cutting acrylic parts on a laser cutter, assembling connecting links between the servos, wiring the servos to the Arduino, and programming the Arduino to control the motion of the platform. Step-by-step instructions are provided covering the cutting, assembly, wiring and programming needed to construct the motion platform.

Uploaded by

swonera
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

Food

Living

Outside

Play

Technology

Workshop

How to build an Arduino-powered 6DOF motion platform


by kroymander on September 29, 2012 Table of Contents How to build an Arduino-powered 6DOF motion platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Intro: How to build an Arduino-powered 6DOF motion platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 1: Cut the acrylic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . File Downloads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 2: Assemble the connecting links . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 3: Glue and install the servo arms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Step 4: Assemble the platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Related Instructables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 2 3 3 3 4 6

http://www.instructables.com/id/How-to-build-an-Arduino-powered-6DOF-motion-platfo/

Intro: How to build an Arduino-powered 6DOF motion platform


This instructable will show you how to create your own six degree of freedom motion platform using an Arduino microcontroller and some standard servo motors for ~$100. The math/programming is somewhat complicated and will be covered in another instructable. Here's a video of some basic movements just by moving a few arms (no math involved yet):

Here is a list of the items (and potential sources) needed to complete this project: 1 Arduino Uno microcontroller (Amazon) 6 standard servos (Parallax) 12 4-40 rod ends (ServoCity) 12 conical spacers (New Era Models) 2 ft 4-40 threaded rod (McMaster-Carr) 16 4-40 11/16" flat head machine screws (McMaster-Carr) 12 4-40 nylok nuts (McMaster-Carr) 4 4-40 3/16" pan head machine screws (McMaster-Carr) 4 4-40 threaded aluminum spacers (McMaster-Carr) 1 mini breadboard (Amazon) 2 sq. ft. 1/4" thick acrylic (TAP plastics) The only hand tools you will need are a small phillips-head screwdriver, a 1/4" wrench, and a 1/8" drill bit/drill, but you will need access to a laser cutter to cut the acrylic. I used a laser cutter at TechShop in Menlo Park. TechShop is a DIY workshop, if you are interested check out their website, www.techshop.ws .

Step 1: Cut the acrylic


The first step is to cut the acrylic. I have attached the files I used, which you can also modify if you want. Make sure to check fitment on the holes for the servo mounting, etc. to make sure the fitment will be right before cutting everything out only to find the holes are too loose. I created these files using Autodesk's AutoCAD Mechanical 2012, which is also available at TechShop if you don't have a copy of your own. There are 3 files to be cut out of 1/4" acrylic: base_bottom.eps, base_top,eps, and platform.eps And 1 file to be cut out of 1/8" acrylic: servo_arms.eps

http://www.instructables.com/id/How-to-build-an-Arduino-powered-6DOF-motion-platfo/

File Downloads

base_bottom.eps (320 KB) [NOTE: When saving, if you see .tmp as the file ext, rename it to 'base_bottom.eps']

base_top.eps (341 KB) [NOTE: When saving, if you see .tmp as the file ext, rename it to 'base_top.eps']

platform.eps (201 KB) [NOTE: When saving, if you see .tmp as the file ext, rename it to 'platform.eps']

Step 2: Assemble the connecting links


The next step is to cut the rods to length. I used 2x 1 ft. sections, which I cut into 6x 4" pieces. Make sure that the ends are cleaned up nicely because they will be threading into plastic which can be easily damaged by the metal if there is a burr. Once the rods are cut to length, simply thread a rod end onto each end of each rod, making sure that all 6 rods are exaclty the same length from end to end when you are done.

Step 3: Glue and install the servo arms


The next step is to glue and install the servo arms onto the servos. I used a liquid acrylic solvent from TAP plastics, but you can use any glue you like. With the liquid solvent approach, I found it helps to lightly sand the surfaces being glued to ensure they stay together. Glue the circular piece to the arm as shown in the picture, making sure that the splined piece still fits onto the servo arm (the laser creates a slightly tapered cut, so the splined pattern will fit on the servo shaft in one orientation better than the other)

http://www.instructables.com/id/How-to-build-an-Arduino-powered-6DOF-motion-platfo/

Step 4: Assemble the platform


Start by threading the servo connectors through the base_top piece from the bottom up, then push the servo into place and thread the connector back down through the other hole. Do this for all 6 servos. Now you can mount the Arduino using the threaded aluminum spacers, 3/16" pan head screws, and 11/16" flat head screws. To make it look nice you can countersink the bottom side of the holes in the acrylic so the flat heads sit flush, but it's entirely necessary. You may also need to shave off a bit of the aluminum spacers so that the fit flat against the Arduino (you'll see what I mean when you try to assemble them). Once the Arduino is mounted, you can stick the breadboard right underneath it, in between all the servos. With the breadboard in place, you can wire everything up. The servos all need +5V on the red wire, ground on the black wire, and signal from the Arduino on the white wire. Make sure you use the PWM capable pins on the Arduino (I used pins.3, 5, 6, 9, 10, 11). Route the wires as shown in the picture. Once everything is wired up, you can install the base_bottom piece. As you can see there is no mounting hardware for the servos, it's just a "press" fit. This is for ease of assembly/disassembly/debugging, so don't worry if you didn't get something wired up correctly. Now it's time to add the connecting links. Start by attaching the links to the servo arms. Use a flat head screw through the rod end, then a conical spacer, then the arm, and into a nylok nut on the back. Before attaching the top, you'll need to drill 1/8" holes in the sides of the platform where the holes for the nuts are. Once you've drilled the holes, the connecting links attach the same way they did on the bottom: a flat head screw through the rod end, then a conical spacer, then the acrylic and into a nylok nut embedded in the platform. Be careful not to overtighten these as the plastic can easily crack. You're done! You can play around with the programming yourself, or you can check out my other instructable on how to program the platform.

http://www.instructables.com/id/How-to-build-an-Arduino-powered-6DOF-motion-platfo/

http://www.instructables.com/id/How-to-build-an-Arduino-powered-6DOF-motion-platfo/

Related Instructables

How to add a Wii nunchuk for realtime position input to your Arduinopowered 6DOF motion platform by kroymander

Project 2: Delta Stewart Robot (video) by Platform (aka the other kind of aggrav8d hexapod) (video) by aggrav8d

My

Quadcop Green/ Black Shield --QUADROTOR (video) by preddy12

Car No. 05 Fourth Stage (Strawberry version) by Kaeru no Ojisan

ATTiny powered Arduino Projects - I made it at TechShop by madebyjoe

http://www.instructables.com/id/How-to-build-an-Arduino-powered-6DOF-motion-platfo/

You might also like