Scribd
Upload
491 views2 pages

Seamless Pipes - API 5L Grade X65 PSL 2

- The document describes specifications for high yield seamless steel pipes that meet API 5L grade X65 PSL 2 standards for use in offshore structures. - The steel pipes have enhanced properties including a minimum yield strength of 450 MPa and meet NACE MR0175 standards for corrosion resistance. - The pipes undergo non-destructive testing, hydrostatic testing, have dimensional tolerances specified, and other quality control and certification requirements to ensure suitability for use in offshore oil and gas structures.

Uploaded by

shiv kr dubey
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
491 views2 pages

Seamless Pipes - API 5L Grade X65 PSL 2

- The document describes specifications for high yield seamless steel pipes that meet API 5L grade X65 PSL 2 standards for use in offshore structures. - The steel pipes have enhanced properties including a minimum yield strength of 450 MPa and meet NACE MR0175 standards for corrosion resistance. - The pipes undergo non-destructive testing, hydrostatic testing, have dimensional tolerances specified, and other quality control and certification requirements to ensure suitability for use in offshore oil and gas structures.

Uploaded by

shiv kr dubey
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Stock Specifications - Pipes

High yield seamless Pipe API 5L grade X65 PSL 2


Suitable for weldable structural steels for fixed offshore structures

X65 (enhanced) high yield seamless pipes, modified to suit offshore structural purposes. Intended for (but not limited to) use in fixed offshore structures, designed to operate in the offshore sector.

Applicable codes and standards


API 5L, 45th Edition / ISO 3183 Specification for line pipe - technical delivery conditions

Grade
X
The X symbol followed by a two or three digit number equal to the specified minimum yield strength in 1000 psi rounded down to the nearest integer.

X 65 Q PSL 2
Minimum Yield
At pipe body 450 MPa (65,300 psi)

Delivery condition
+ N Normalizing rolling + Q Quenched and tempered where Q refers to a heat treatment process consisting of quench hardening followed by tempering.

PSL
PSL refers to the product specification level where PSL2 provides a more extensive chemical composition complete with a mandatory minimum fracture toughness.

- The steel pipe mentioned herein is substantially modified from the API 5L, X65 standard. - Pipes are fully killed and fine grain steel material. - NACE MR0175:Satisfactory - This steel offers enhanced yield tensile ratio of 0.87 (max) and impact values verified from as low as -30C. - This grade is also known as L450Q in USC Units.

Chemical composition with thickness (t) 25mm


Product analysis in % (All values are max. unless otherwise stated.)
C Si Mn P S Cr Mo Ni Al 0,16 0,50 1,10 - 1,60 0,022 0,005 0,50 0,20
3

Cu N Nb Ti V As Sb Sn Pb
1

0,20 0,014 0,05 0,02 0,10 0,02 0,01 0,015 0,010

Cr+Mo+Ni+Cu Nb+V Nb+V+Ti CEV (IIW) see formula below Pcm see formula below

0,54 0,10 0,15 0,432 0,252

Bi Ca B

0,010 0,005 0,0005

0,20 0,020 - 0,060

CEV = C +
1 2

Mn 6

Cr+Mo+V 5

Ni+Cu 15

Pcm = C +

Si 30

Mn+Cu+Cr 20

Ni 60

Mo 15

V 10

+ 5B

All nitrogen shall be tied up as nitrides. Al (total) to N ratio shall be at least 2.2:1 CEV & Pcm may vary as wall thickness of pipe increases. 3 Mo, max 0.25% for thickness (t) > 25mm. 4 Max 0.60% for thickness (t) > 25mm.

Mechanical properties
Thickness t
mm -

API 5L, enhanced grade X65Q, PSL 2 Yield Reh


MPa min. 450

Tensile Rm
MPa Min. 535 Max. 760

Reh / Rm
max. 0,93

CVN
-30 C min. 36J avg. 42J transverse

El
% min. 22

Surface (a) All surfaces have been 100% visually inspected. The surface condition complies with API 5L Annex E. (b) External surface of pipe shall be coated with a layer of varnish. NDT All pipes will be ultrasonic tested on pipe body and pipe end as per API 5L Annex E, Table E.2 and para E.3.3. Coverage: (a) longitudinal: 100% of the pipe surface (b) pipe ends not scanned by automatic ultrasonic system shall be inspected by manual UT or Magnetic Particle Examination. Hydrostatic test (a) Test pressure may not exceed 2970 psi in accordance to API 5L requirements (b) Holding time: minimum 5 seconds Certification and traceability All dimensions will be supplied with a 3.2 certificate according to EN 10204, endorsed by recognized and independent inspection agency. Marking shall be in SI units (X65) accordance with API requirements & mill standard. Dimensional control All dimensions will be supplied according to API 5L clause 9.11; In addition, the following tolerances apply: (a) Pipe body: +/- 0,75% (b) Pipe end: +/- 0,5% (c) Wall thickness: +15%, -12,5% (d) Length: -0 / +100mm Pipe Ends Pipe Ends are bevelled. End angle shall be 30- 0/+5, root face shall be 1.6mm +/- 0.8mm and fitted with bevel protectors. Protection Pipes are varnished on the outside.

Rev 1 I September 2013

You might also like