Scribd
Upload
217 views

Simulation of Halfwave Inverter Using Psim

The document describes simulating a half wave inverter circuit using PSIM software. It lists the components needed including a voltage source, IGBT switches, resistor and capacitor load. It provides the procedure to build the circuit model in PSIM, set parameters, run the simulation and view the output voltage waveform across the resistor and top and bottom switch waveforms. The simulation is run and results in the desired half wave inverter output voltage and switch waveforms being displayed.

Uploaded by

Darshan Patel
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
217 views

Simulation of Halfwave Inverter Using Psim

The document describes simulating a half wave inverter circuit using PSIM software. It lists the components needed including a voltage source, IGBT switches, resistor and capacitor load. It provides the procedure to build the circuit model in PSIM, set parameters, run the simulation and view the output voltage waveform across the resistor and top and bottom switch waveforms. The simulation is run and results in the desired half wave inverter output voltage and switch waveforms being displayed.

Uploaded by

Darshan Patel
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

SIMULATION OF HALFWAVE INVERTER USING PSIM

EX.NO: DATE:

Aim: To Simulate Half wave rectifier to observe the following waveforms by using PSIM.
(1) Output Voltage across R. (2) Top and bottom waveforms of switch used(IGBT)

Requirements:
Table 1: Half wave inverter Components Tool Box / Library browser Elements /Source /Voltage/Sine Elements /Power /Switch/IGBT Elements /Power /RLC Branches Elements/Power /RLC Branches Elements/Power /Switch/Gating block Block parameters

Voltage Source

DC

Amplitude = 230 Frequency = 50

Switch

IGBT Default Resistor Resistance(Kilo ohm) = 100

Load

Capacitance

Capacitance

Capcitance(micro faraday)=10

Gating pulse

Gating block

Top ON from 0-180c Bottom ON from 180-360c

Procedure:
Steps to create Simulation Model using PSIM: 1. Click on File New. 2. Make/Model the circuit by placing all its Blocks from its corresponding Library/toolbox, which is clearly shown in the table 1. Right click on the block to rotate mirror etc. to organize the circuit elements. 3. To change the circuit parameters applicable to the block by double clicking on the block/element and type the values. Keep the values default for some blocks like thyristor, diodes, mosfet etc. Power Electronics-II EE Department, SPCE

4. To measure/observe the voltage across or current passes through the electrical block/device, connect voltmeter blocks , it is available on the Elements/others/Probes/Voltmeter To observe the waveform provide the clock from the simulate/simulation control provide time to observe the wave form. 5. For Half wave inverter, components required and its parameter values tabulated in Table 1. The schematic arrangement is shown in schematic diagram.

Steps to simulating the circuit using PSIM: 1. After correcting all errors start by creating a simulation. 2. To run the simulation, select simulate Run Simulation. 3. If any errors are reported here. Correct schematic or the simulation settings and re-run simulation. 4. To view simulation plots on simulation window, add the desired output name on the right side of the window. 5. The waveforms obtained are shown in Fig 1, 2.

Schematic diagram: 1 Half wave inverter

G1 10u C1 vo 0 180. IGBT1

V
Vin 100 R 100k G2 10u C2 180 360. IGBT2 switch(IGBT1) is ON from 0-180. switch(IGBT2) is ON from 180-360.

Power Electronics-II

EE Department, SPCE

Output voltage and top, bottom(IGBT) Voltage waveform

Result:
A single phase half wave inverter model is created and analyzed the various waveforms by using PSIM.

Power Electronics-II

EE Department, SPCE

You might also like