MCC

PRODUCT ATTRIBUTES
Submicron linewidth control Sub 0.1m imaging E-beam, X-ray & deep UV imaging Broad range of molecular weights & dilutions Excellent adhesion to most substrates Compatible with multi-layer processes

NANO PMMA and Copolymer

PMMA (polymethyl methacrylate) is a versatile polymeric material that is well suited for many imaging and non-imaging microelectronic applications. PMMA is most commonly used as a high resolution positive resist for direct write e-beam as well as x-ray and deep UV microlithographic processes. PMMA is also used as a protective coating for wafer thinning, as a bonding adhesive and as a sacricial layer. Standard PMMA products cover a wide range of lm thicknesses and are formulated with 495,000 & 950,000 molecular weight (MW) resins in either chlorobenzene or the safer solvent anisole. Custom MW products ranging from 50,000 - 2.2 million are available upon request. In addition, we offer copolymer (MMA (8.5) MAA) products formulated in the safer solvent ethyl lactate. All MCC PMMA and copolymer resists

APPLICATIONS
Multi-layer T-gate processing Direct write e-beam lithography Protective coatings for wafer thinning Adhesive for X-ray LIGA processing Sacricial layers

are available in package sizes from 500ml to 20 liters.

courtesy M/A Com

100nm gate prole imaged in 495K PMMA with 8.5 MAA Copolymer on top.

courtesy M/A Com

T-gate resulting from PMMA/Copolymer bilayer resist stack.

PROCESSING GUIDELINES
Substrate Preparation
The substrate should be clean and dry. Solvent, O2 plasma, and O3 cleans are commonly used and recommended.

Typical process ow for bi-layer T-gate process

1.

Coat
MicroChem PMMA resists produce low defect coatings over a broad range of lm thicknesses. The lm thickness vs. spin-speed curves displayed in Fig. 1 through 8 provide the information required to select the appropriate PMMA dilution and spin speed needed to achieve the desired lm thickness.

Spin Coat Bottom Layer PMMA Resist

2.

Prebake PMMA

Spin Coat Top Layer Copolymer Resist

3.

4.

Remove Resist Edge Bead

The recommended coating conditions are: (1) Dispense: STATIC (2) Spread: DYNAMIC STATIC (3) Spin: 5 - 8ml for a 150mm wafer 500 rpm for 5 sec OR 0 rpm for 10 sec
5. 6.

Ramp to final spin speed at a high acceleration rate and hold for a total of 45 seconds.

Prebake Copolymer

Expose and Develop Resist Stack

Pre Bake
PMMA Hot plate: Convection Oven: Copolymer Hot plate: Convection Oven: 150oC for 60 - 90 sec OR 140oC for 30 min 180oC for 60 - 90 sec OR 170oC for 30 min
7. 8.

Gate Etch and Deposition

Strip/Remove Resist Stack

*Vacuum oven bake can also be used

Expose
PMMA can be exposed with various parts of the electromagnetic spectrum. e-b eam: Do se - 50 - 500 C/ cm 2 depending on radiation source/equipment & developer used. Energy 20-50kV; higher kV for higher resolution, e.g. 50kV for 0.1mm images. DUV(deep UV): Low sensitivity, requiring doses >500mJ/c m 2 at 248nm. X-ray: Sensitivity of PMMA is low, ~1-2 J/cm2 at 8.3. The sensitivity increases at longer x-ray wavelengths. Features of <0.02m can be fabricated.

Table 2 outlines helpful guidelines for a develop process.

TYPICAL DEVELOPMENT PROCESS

ACTION Dispense Dispense No Dispense Rinse * Dry 500 rpm for 30-45 secs 500 rpm for 30 secs SPRAY** 500 rpm for 30-45 secs SPRAY PUDDLE 500 rpm for 3-4 secs 0 rpm for 2 secs 0 rpm for 25-40 secs 500 rpm for 3-4 secs 5000 rpm for 30 secs 30 secs 30 secs Nitrogen blow dry IMMERSION (21OC)

* Recommended Rinse solution is MIBK to IPA 1:3 in order to reduce the possibility of scumming ** Variables such as developer pressure, nozzle type & position, spray pattern, etc. should be optimized

Table 2 Postbake/Hardbake (optional)

To remove residual developer, rinse solvent, and moisture from the resist image. Hot Plate OR Convection Oven 100oC for 60 - 90 sec 95oC for 30 min

Develop
PMMA and copolymer resists are compatible with immersion (21oC), spray puddle, and spray process modes. Process variables such as soft bake, exposure conditions, choice of resist and developer should be optimized to achieve desired results. For more process details see the PMMA and Copolymer DEVELOPER data sheet. Table 1 lists commonly used developers and their recommended usage.

Note: PMMA images will round/ow above 125oC.

Remove Wet: Bath: Spray: Dry: Remover PG or ACRYL STRIP time as required, ambient time as required, 500 - 1000 rpm plasma O2

NANOTM PMMA AND COPOLYMER DEVELOPERS ARE AVAILABLE IN THE FOLLOWING BLENDS
PRODUCT COMPOSITION RESOLUTION SENSITIVITY / THROUGHPUT high medium low high

PMMA and copolymer resists can be removed by using MCC's Remover PG or standard cleanroom solvents, such as acetone, photoresist thinner, or positive photoresist removers. Resists that have seen higher processing temperatures and/or hostile processes that have toughened the polymer will require ACRYL STRIP or a more aggressive removal process. This can include Remover PG at elevated temperature followed by cleaner baths to assure adequate material removal. See appropriate product data sheet for specic process recommendations and safety precautions. For additional questions or technical assistance please contact Technical Services.

M/I 1:1 M/I 1:2 M/I 1:3 MIBK

1:1 MIBK to IPA 1:2 MIBK to IPA 1:3 MIBK to IPA MIBK

high higher very high low

Table 1 Rinse and Dry

To terminate the develop process and prevent scumming, PMMA and copolymer should be immersed or sprayed with 1:3 or 1:4 MIBK:IPA, alcohol or DI water immediately following develop. Substrates are normally spin dried at 3000rpm for 20 seconds or N2 blow dried.

SPIN SPEED CURVES FOR PMMA AND COPOLYMER RESISTS

The spin speed versus lm thickness curves displayed in gures 1-11 provide approximate information required to select the appropriate PMMA or copolymer resist and spin conditions needed to obtain the desired lm thickness. Actual results will vary and are equipment, environment, process and application specic. Additional resist dilutions to obtain other lm thicknesses are available upon request.

495PMMA C Resists Solids: 2% - 6% in Chlorobenzene

10000 9000 8000 7000 6000 5000 4000 3000 2000 1000 0 500 1000 1500 2000 2500 3000 3500 Spin Speed (rpm)

495PMMA A Resists Solids: 2% - 6% in Anisole

7000 6000 Film Thickness () 5000 4000 3000 2000 1000 0
4500 C6

Film Thickness ()

A6 A4 A2 1000 1500 2000 2500 3000 3500 4000 4500

C4 C2 4000

500

Spin Speed (rpm)

Figure 1

Figure 3

495PMMA C Resists Solids: 8% - 9% in Chlorobenzene

25000 23000 21000 19000 17000 15000 13000 11000 9000 7000 5000 500 1000 1500 2000 2500 3000 3500 Spin Speed (rpm) Film Thickness () 20000 15000 10000 5000 0 4000 4500 500 1000

495PMMA A Resists Solids: 8% - 11% in Anisole

Film Thickness ()

C9

A11 A8

C8 1500 2000 2500 3000 3500

4000

4500

Spin Speed (rpm)

Figure 2

Figure 4

Copolymer Resists Solids: 6% - 11% in Ethyl Lactate

12000

Film Thickness, ()

10000 8000 6000 4000 2000 0 500 1000 1500 2000 2500 3000 3500 4000 4500
EL 11 EL 9 EL 6

Spin Speed (rpm)

Figure 9

950PMMA C Resists Solids: 9% - 10% in Chlorobenzene

55000 50000 45000 40000 35000 30000 25000 20000 15000 10000 500 1000 1500 2000 2500 3000 3500 Spin Speed (rpm)
55000 50000 45000 40000 35000 30000 25000 20000 15000 10000 500 1000

950PMMA A Resists Solids: 9% - 11% in Anisole

Film Thickness ()

C10 C9 4000 4500

Film Thickness ()

A11 A9 1500 2000 2500 3000 3500 4000 4500

Spin Speed (rpm)

Figure 5

Figure 7

950PMMA C Resists Solids: 2% - 7% in Chlorobenzene

25000 Film Thickness () 20000
Film Thickness () 12000 10000 8000 6000 4000 2000

950PMMA A Resists Solids: 2% - 7% in Anisole

15000 10000 5000 0 500 C7 C4 C2 1000 1500 2000 2500 3000 3500 4000 4500 Spin Speed (rpm)

A7 A4 A2 1000 1500 2000 2500 3000 3500 4000 4500

0 500

Spin Speed (rpm)

Figure 6

Figure 8

Optical Properties 495 and 950 PMMA Resists

1.7

Optical Properties Copolymer Resists

1.7

1.65

Cauchy Coeffiecients A 495 PMMA 950 PMMA 1.491 1.488

B 3.427 e-03 2.898 e-03

C 1.819 e-04 1.579 e-04

1.65

Cauchy Coeffiecients A 8.5 mEL 1.478

C -3.478 e-04

7.204 e-04

Refractive Index

1.6

Refractive Index
0 300 500

1.6

1.55

1.55

1.5

1.5

1.45

700

900

1.45 0 300 500

Wavelength (nm)

700

900

Wavelength (nm)

Figure 10

Figure 11

Bi-Layer Process

PMMA resists for T-gate and other imaging processes PMMA is a high resolution positive tone resist for e-beam, deep UV (200-250nm) and X-ray lithographic processes. Although PMMA may be used in a single layer resist process, it is most commonly used in multi-layer processes such as in the fabrication of mushroom or T-gates. Images are formed through the photo scission of the polymer backbone and subsequent development process, which removes the exposed, lower molecular weight resist. Multi-layer, shaped resist proles are realized and inuenced through the careful choice of PMMA molecular weight, lm thickness and other process set points.
3. Expose resist stack, center scan dose, then side scan dose 2. Coat and bake copolymer 1. Coat and bake PMMA

PMMA GaAs

PMMA GaAs

4. Develop PMMA and Copolymer

Copolymer PMMA GaAs GaAs

5. Deposition

e-beam >> PMMA GaAs GaAs

6. Strip resist stack

Tri-Layer Process

In a typical bi-layer process, a combination of bottom and top layer resists are selected such that a large difference in dissolution rates of the layers at the developer step exists, leading to the desired resist sidewall prole. This contrast may be further inuenced with a variety of process strategies. Generally, dissolution rate increases as molecular weight decreases. However, soft bake conditions, which affect residual solvent level and subsequent development rates will inuence the bi-layer resist prole as will the exposure conditions. Please refer to our web site, www.microchem.com for applications notes concerning non-imaging PMMA processes such as wafer thinning, bonding and sacricial layers.
2. Coat and bake copolymer 1. Coat and bake high MW PMMA

PMMA GaAs

PMMA Copolymer PMMA GaAs

5. Develop tri-layer stack

Copolymer PMMA GaAs

PMMA Copolymer PMMA GaAs

6. Deposition

PMMA Copolymer PMMA GaAs GaAs

3. Coat and bake low MW PMMA

e-beam >> PMMA Copolymer PMMA GaAs

7. Strip resist stack

4. Expose resist stack, center scan dose, then side scan dose

OTHER RESIST AND ANCILLORY PRODUCTS FROM MICROCHEM

PMGI and LOR for lift-off processing SU-8 resists for MEMS and ultra thick resist processing Remover PG resist stripper EBR PG edge bead remover Acryl Strip resist stripper for PMMA

NOTES

HANDLING NANO PMMA & COPOLYMER SERIES RESISTS (in Anisole or Chlorobenzene)
Use precautions in handling ammable PMMA solutions. Avoid contact with eyes, skin, and clothing. Use with adequate ventilation. Avoid breathing fumes. Wear chemical-resistant eye protection, chemical gloves (PVA for chlorobenzene solutions) and protective clothing when handling NANO PMMA & Copolymer Series Resist products. NANO PMMA & Copolymer Series Resists cause irritation in case of contact with eyes, skin, and mucous membranes. In case of eye contact, ush with water for 15 minutes and call a physician immediately. Review the current MSDS (Material Safety Data Sheet) before using.

MATERIAL AND EQUIPMENT COMPATIBILITY

NANO PMMA & Copolymer Resists are compatible with glass, ceramic, unfilled polyethylene, high-density polyethylene, polytetrauoroethylene, stainless steel, and equivalent materials. Chlorobenzene is a powerful solvent and will attack various elastomers such as BUNA N, EPDM, HYPALON, and NEOPRENE. It will also attack PVC, CPVC and polyester. VITON A is recommended for both O-rings and tubing.

PROCESSING ENVIRONMENT
For optimum results, use NANO PMMA & Copolymer Series Resists in a controlled environment. 20 - 25o 1oC (68 - 77oF) is suggested.

STORAGE
Store upright in original containers in a dry area 50 - 80oF (10 - 27oC ). Do not refrigerate. Keepaway from sources of ignition, light, heat, oxidants, acids, and reducers. Shelf life is 13 months from date of manufacture.

DISPOSAL
Each locality, state, and county has unique regulations regarding the disposal of organic solvents such as NANO PMMA Series Resists. It is the responsibility of the customer to dispose of NANO PMMA Series Resists in compliance with all applicable codes and regulations. See MSDS for additional information.

1254 C HESTNUT S TREET N EWTON , MA 02464 P HONE : 617.965.5511 F AX : 617.965.5818 E MAIL :

The information regarding these products is based on our testing to date, which we believe to be reliable, but accuracy or completeness is not guaranteed. We make no guarantee or warranty, expressed or implied, regarding the information, use, handling, storage, or possession of these products, or the application of any process described herein or the results desired, since the use and handling of these products are beyond our control.
MicroChem Corp. copyright 2001. All rights reserved. LOR is a trademark of MicroChem Corp.

[email protected]

WWW.MICROCHEM.COM