Scribd
Upload
96 views

Praveen Kumar.a: Question Paper Code

This document contains the question paper for the subject "Vibration Analysis and Control" with 15 questions. It provides definitions for terms like degrees of freedom, influence coefficients, critical speed of shaft, transient vibration and principal modes of vibration. It also contains questions on topics like natural frequency calculation for single degree and multi degree systems, vibration isolation materials, vibration absorbers, free vibration testing, and vibration exciters. Students are required to answer all questions that may include derivations, calculations and explanations with diagrams.

Uploaded by

Ashok
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
96 views

Praveen Kumar.a: Question Paper Code

This document contains the question paper for the subject "Vibration Analysis and Control" with 15 questions. It provides definitions for terms like degrees of freedom, influence coefficients, critical speed of shaft, transient vibration and principal modes of vibration. It also contains questions on topics like natural frequency calculation for single degree and multi degree systems, vibration isolation materials, vibration absorbers, free vibration testing, and vibration exciters. Students are required to answer all questions that may include derivations, calculations and explanations with diagrams.

Uploaded by

Ashok
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Question Paper Code :

33099

Common to M.E. CAD/CAM/M.E. Computer Aided Design/M.E. Engineering Design/M.E. Computer Aided Design (Part-Time) Second Semester

220203 VIBRATION ANALYSIS AND CONTROL (Regulation 2010) Time : Three hours

31

Answer ALL questions.

1. 2. 3. 4. 5. 6. 7.
8.

What are the sources of vibration?

State Rayleighs maximum energy principle. Define the term critical speed of shaft.

What are principal modes of vibration? What is meant by transient vibration? Define the term degrees of freedom. Define the influence coefficients a ij an k ij .

53

10 5

A vibration of harmonic type has a frequency of 10 cps and its maximum velocity is 4.5 m/s. Determine its amplitude and time period. List any two materials used as vibration absorber.

9.

10.

What is meant by lumped mass system?

31

05

PART A (10 2 = 20 marks)

05

M.E./M.Tech. DEGREE EXAMINATION, NOVEMBER/DECEMBER 2011.

31

Praveen kumar.A

Reg. No. :

Maximum : 100 marks

PART B (5 16 = 80 marks) 11. (a)

What is an accelerometer? What are the main specifications of accelerometer? Explain the working principle of crystal type accelerometer with neat sketch. (16) Or

(b)

Derive the governing differential equation and deduce the natural frequency of vibrations for the system shown in figure. (16)

12.

(a)

A uniform shaft is supported at three different points as shown in figure. Two rotors of equal weight are attached to the shaft at distances L from the ends. Derive the necessary equations and obtain expressions for natural frequencies of the system. (16)

31 53 10 5
(b)

Obtain the governing equations for the system shown below. Determine the natural frequencies and plot the mode shapes of the system. Take M1 = 10kg; M2 = 8kg; K1 = K 2 = 250N/cm; K 3 = 200 N/cm. (16)

05
Or 2

31
33099

05

31

Praveen kumar.A

13.

(a)

(i) (ii)

Prove the orthogonality character of eigen vectors.

9 [M ] =

1 49 2 , [K ] = 1 1 2 2

Find the natural frequencies and mode shapes of this system. Or (b)

A vibrating system having mass 1 kg is suspended by a spring stiffness 1000 N/m and it is put to harmonic excitation of 10 N. Assuming viscous damping, determine (i) (ii) Resonant frequency Phase angle at resonance

(iii) Amplitude at resonance (iv) 14. (a) (i) (ii) Damped frequency.

31
Or Or
3

05

Praveen kumar.A
(16)

What is vibration isolation? when is vibration isolation required? Name a few materials suitable for achieving vibration isolation. (12) What is meant by vibration severity standards?

05

31

A dynamically coupled system is given by the following:

(b)

List the different types of vibration absorbers and explain any two in detail. (16)

(i) (ii)

31

15.

(a)

Write short notes on the following : Free vibration test

Frequency measuring instruments.

10 5

(b)

What are vibration exciters? List the different types of vibration exciters and explain any two in detail. (16)

Praveen kumar.A

53

(8) (8)

(4)

(8) (8)

33099

You might also like