Scribd
Upload
185 views

SO 13320, Particle Size Analysis - Laser Diffraction Methods - Part 1: General Principles

Particle size is important across many industries as it influences critical properties. While a single number cannot describe a distribution, central values like the mean, median, and mode provide a point of reference. The mean is a calculated average value, with different definitions existing depending on if the distribution is based on number, surface area, or volume. The median is often used instead of the mean for laser diffraction results which are reported on a volume basis. Understanding distribution widths through values like standard deviation provides fuller characterization beyond just a central point.

Uploaded by

louisprice
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
185 views

SO 13320, Particle Size Analysis - Laser Diffraction Methods - Part 1: General Principles

Particle size is important across many industries as it influences critical properties. While a single number cannot describe a distribution, central values like the mean, median, and mode provide a point of reference. The mean is a calculated average value, with different definitions existing depending on if the distribution is based on number, surface area, or volume. The median is often used instead of the mean for laser diffraction results which are reported on a volume basis. Understanding distribution widths through values like standard deviation provides fuller characterization beyond just a central point.

Uploaded by

louisprice
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

A GUIDEBOOK TO PARTICLE SIZE ANALYSIS

TABLE OF CONTENTS

1 Why is particle size important?

Which size to measure


3 Understanding and interpreting particle size distribution calculations

Central values: mean, median, mode Distribution widths Technique dependence Laser diffraction Dynamic light scattering Image analysis

8 Particle size result interpretation: number vs. volume distributions Transforming results 10 Setting particle size specications

Distribution basis Distribution points Including a mean value X vs.Y axis Testing reproducibility Including the error Setting specications for various analysis techniques

Particle Size Analysis Techniques


15 LA-950 laser diffraction technique

The importance of optical model Building a state of the art laser diffraction analyzer
18 SZ-100 dynamic light scattering technique

Calculating particle size Zeta Potential Molecular weight


23 PSA300 and CAMSIZER image analysis techniques

Static image analysis Dynamic image analysis

26 Dynamic range of the HORIBA particle characterization systems 27 Selecting a particle size analyzer

When to choose laser diffraction When to choose dynamic light scattering When to choose image analysis
29 References

Why is

particle size important?


Particle size inuences many properties of particulate materials and is a valuable indicator of quality and performance. This is true for powders, suspensions, emulsions, and aerosols. The size and shape of powders inuences ow and compaction properties. Larger, more spherical particles will typically ow more easily than smaller or high aspect ratio particles. Smaller particles dissolve more quickly and lead to higher suspension viscosities than larger ones. Smaller droplet sizes and higher surface charge (zeta potential) will typically improve suspension and emulsion stability. Powder or droplets in the range of 2-5m aerosolize better and will penetrate into lungs deeper than larger sizes. For these and many other reasons it is important to measure and control the particle size distribution of many products. Measurements in the laboratory are often made to support unit operations taking place in a process environment. The most obvious example is milling (or size reduction by another technology) where the goal of the operation is to reduce particle size to a desired specication. Many other size reduction operations and technologies also require lab measurements to track changes in particle size including crushing, homogenization, emulsication, microuidization, and others. Separation steps such as screening, ltering, cyclones, etc. may be monitored by measuring particle size before and after the process. Particle size growth may be monitored during operations such as granulation or crystallization. Determining the particle size of powders requiring mixing is common since materials with similar and narrower distributions are less prone to segregation. There are also industry/application specic reasons why controlling and measuring particle size is important. In the paint and pigment industries particle size inuences appearance properties including gloss and tinctorial strength. Particle size of the cocoa powder used in chocolate affects color and avor. The size and shape of the glass beads used in highway paint impacts reectivity. Cement particle size inuences hydration rate & strength. The size and shape distribution of the metal particles impacts powder behavior during die lling, compaction, and sintering, and therefore inuences the physical properties of the parts created. In the pharmaceutical industry the size of active ingredients inuences critical characteristics including content uniformity, dissolution and absorption rates. Other industries where particle size plays an important role include nanotechnology, proteins, cosmetics, polymers, soils, abrasives, fertilizers, and many more.

Particle size is critical within a vast number of industries. For example, it determines:
appearance and gloss of paint avor of cocoa powder reectivity of highway paint hydration rate & strength of cement properties of die lling powder absorption rates of pharmaceuticals appearances of cosmetics

WHICH SIZE TO MEASURE?

DIAMETER

VERTICAL PROJECTION

A spherical particle can be described using a single numberthe diameter because every dimension is identical. As seen in Figure 1, non-spherical particles can be described using multiple length and width measures (horizontal and vertical projections are shown here). These descriptions provide greater accuracy, but also greater complexity. Thus, many techniques make the useful and convenient assumption that every particle is a sphere. The reported value is typically an equivalent spherical diameter. This is essentially taking the physical measured value (i.e. scattered light, settling rate) and determining the size of the sphere that could produce the data. Although this approach is simplistic and not perfectly accurate, the shapes of particles generated by most industrial processes are such that the spherical assumption does not cause serious problems. Problems can arise, however, if the individual particles have a very large aspect ratio, such as bers or needles. Shape factor causes disagreements when particles are measured with different particle size analyzers. Each measurement technique detects size through the use of its own physical principle. For example, a sieve will tend to emphasize the second smallest dimension because of the way particles must orient themselves to pass through the mesh opening. A sedimentometer measures the rate of fall of the particle through a viscous medium, with the other particles and/or the container walls tending to slow their movement. Flaky or plate-like particles will orient to maximize drag while sedimenting, shifting the reported particle size in the smaller direction. A light scattering device will average the various dimensions as the particles ow randomly through the light beam, producing a distribution of sizes from the smallest to the largest dimensions. The only techniques that can describe particle size using multiple values are microscopy or automated image analysis. An image analysis system could describe the non-spherical particle seen in Figure 1 using the longest and shortest diameters, perimeter, projected area, or again by equivalent spherical diameter. When reporting a particle size distribution the most common format used even for image analysis systems is equivalent spherical diameter on the x axis and percent on the y axis. It is only for elongated or brous particles that the x axis is typically displayed as length rather than equivalent spherical diameter.

HORIZONTAL PROJECTION

gure 1 SHAPE FACTOR


Many techniques make the general assumption that every particle is a sphere and report the value of some equivalent diameter. Microscopy or automated image analysis are the only techniques that can describe particle size using multiple values for particles with larger aspect ratios.

Understanding and interpreting particle size distribution calculations.


Performing a particle size analysis is the best way to answer the question: What size are those particles? Once the analysis is complete the user has a variety of approaches for reporting the result. Some people prefer a single number answerwhat is the average size? More experienced particle scientists cringe when they hear this question, knowing that a single number cannot describe the distribution of the sample. A better approach is to report both a central point of the distribution along with one or more values to describe the width of distribution. Other approaches are also described in this document.
CENTRAL VALUES: MEAN, MEDIAN, MODE

For symmetric distributions such as the one shown in Figure 2 all central values are equivalent: mean = median = mode. But what do these values represent?
MEAN

Mean is a calculated value similar to the concept of average. The various mean calculations are dened in several standard documents (ref.1,2). There are multiple denitions for mean because the mean value is associated with the basis of the distribution calculation (number, surface, volume). See (ref. 3) for an explanation of number, surface, and volume distributions. Laser diffraction results are reported on a volume basis, so the volume mean can be used to dene the central point although the median is more frequently used than the mean when using this technique. The equation for dening the volume mean is shown below. The best way to think about this calculation is to think of a histogram table showing the upper and lower limits of n size channels along with the percent within this channel. The Di value for each channel is the geometric mean, the square root of upper x lower diameters. For the numerator take the geometric Di to the fourth power x the percent in that channel, summed over all channels. For the denominator take the geometric Di to the third power x the percent in that channel, summed over all channels.

gure 2

SYMMETRIC DISTRIBUTION WHERE MEAN=MEDIAN=MODE

You might also like