Scribd
Upload
571 views

High Level Data Link Control (HDLC)

The High Level Data Link Control (HDLC) protocol was developed by ISO to standardize data link layers. It supports both switched and non-switched networks using a bit-oriented architecture. HDLC can be used for half-duplex, full-duplex, point-to-point, and multi-point networks. It defines primary, secondary, and combined station types in either balanced, unbalanced, or symmetrical configurations. The normal response mode requires secondary stations to wait for authorization from the primary station before transmitting frames, while the asynchronous modes allow secondary stations to transmit independently to reduce overhead.

Uploaded by

ksureshkaliyan
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
571 views

High Level Data Link Control (HDLC)

The High Level Data Link Control (HDLC) protocol was developed by ISO to standardize data link layers. It supports both switched and non-switched networks using a bit-oriented architecture. HDLC can be used for half-duplex, full-duplex, point-to-point, and multi-point networks. It defines primary, secondary, and combined station types in either balanced, unbalanced, or symmetrical configurations. The normal response mode requires secondary stations to wait for authorization from the primary station before transmitting frames, while the asynchronous modes allow secondary stations to transmit independently to reduce overhead.

Uploaded by

ksureshkaliyan
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 3

High Level Data Link Control (HDLC)

High Level Data Link Control (HDLC)

The High Level Data Link Control protocol was developed by the International
Organization for Standardization (ISO). It is used for switched and non-switched
networks and is a bit oriented architecture. The High Level Data Link Control has
been accepted and used widely because it supports almost all kinds of functionalities
like half duplex, full duplex, point to point and multi-point networks. The bit patterns
are standard in HDLC and therefore the information exchanged follows the same
pattern. This minimizes the chances of any errors.

HDLC Features

The main features of HDLC are divided into various aspects


• The modes for operation
• Stations
• Configuration
• Frames and Structures
• The subsets of HDLC

HDLC Stations and Configurations

The HDLC has three levels of stations, the primary station, secondary station and the
combined station.

The primary station is responsible for controlling all the other secondary stations for a
network that uses the HDLC protocol. The primary station also takes care of the error
control aspect and organizes the data flow on the links.

The secondary station is controlled by the primary station and is activated when the
primary station sends a request.

The combined station controls the links and overlooks the primary and the secondary
stations functions. The combined stations have complete control over the links and do
not need the authorization of any other station.
These stations are further dependant on the configuration types and basically follow
three different types of configuration.

Unbalanced Configuration: In an unbalanced configuration there is one primary


station and the remaining stations are all secondary stations that are controlled by the
primary station. Unbalanced configuration supports many types of operations like half
duplex, full duplex, point to point configuration and multi point configuration.

Balanced Configuration: In a balanced configuration there are two or more combined


configurations however there are limitations when it comes to the balanced
configurations since it can use only specific configurations like the half and full
duplex operations or point to point network configurations.

Symmetrical Configuration: The symmetrical configuration is a combination of


balanced and unbalanced configurations and is rarely used in current day technology.
In this type of configuration each station in the network has two kinds of status; one is
primary and the secondary status.

There are several modes of operation for the above configurations in the HDLC.

Normal Response Mode (NRM): The Normal Response Mode is used only with the
unbalanced configurations. The primary station usually requests information from the
secondary station and only then the secondary station initiates the data transfer. The
response is transferred after the primary station authorizes the transaction.

This procedure is followed for each and every frame that is being transferred. After
the last frame is sent or transferred then the procedure sets back itself to zero where
the entire gamut of taking permission is repeated for the next set of frames.

Asynchronous Response Mode (ARM): The ARM can be used with balanced or
combined configuration as it does not need any authorization from the primary station
to start transferring the frames from the secondary station. It reduced the time
overheads while transferring the frames and since the permissions are not required.
Asynchronous Balanced Mode (ABM): The asynchronous balanced mode is not very
different from the asynchronous response mode. Even this mode does not require
permissions from the primary station in order to transfer data or frames from the
secondary station. The ABM mode is better for multi point nodes whereas the ARM is
better for the point to point nodes. However this mode is not being widely used in
modern day technology.

You might also like