Wireless G Plus MIMO

Router

User Manual
F5D9230-4

Table of Contents

1.

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Advantages of a Wireless Network . . . . . . . . . . . . . . . . . . . 1 Placement of your Wireless G Plus MIMO Router . . . . . . . . 2

2. 3.

Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Knowing your Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Setup Assistant Software System Requirements. . . . . . . . . 9

4. 5. 6.

Connecting and Configuring your Router . . . . . . . . . . . . . . 14 Alternate Setup Method . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Using the Web-Based Advanced User Interface . . . . . . . . . 45 Changing LAN Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Viewing the DHCP Client List Page . . . . . . . . . . . . . . . . . . 48 Configuring the Wireless Network Settings . . . . . . . . . . . . 49 Setting WPA Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Setting WEP Encryption . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Using the Access Point Mode . . . . . . . . . . . . . . . . . . . . . . 60 Setting MAC Address Control . . . . . . . . . . . . . . . . . . . . . . 61 Configuring the Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Using Dynamic DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Restarting the Router. . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Updating the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . 79

7. 8. 9.

Manually Configuring Network Settings . . . . . . . . . . . . . . 88 Recommended Web Browser Settings . . . . . . . . . . . . . . . . 96 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

10. Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

Introduction
section

Thank you for purchasing the Belkin Wireless G Plus MIMO Router (the Router). Following are two short sectionsthe first discusses the benefits of home networking, and the other outlines best practices that maximize your wireless home network range and performance. Please be sure to read through this User Manual completely, and pay special attention to the section entitled Placement of your Wireless Networking Hardware for Optimal Performance on the next page. By following our simple setup instructions you will be able to use your Belkin Home Network to: Share one high-speed Internet connection with all the computers in your home Share resources, such as files and hard drives among all the connected computers in your home Share a single printer with the entire family Share documents, music, video, and digital pictures Store, retrieve, and copy files from one computer to another Simultaneously play games online, check Internet email, and chat

1 2 3 4 5 6 7 8 9 10

Advantages of a Wireless Network

Here are some of the advantages of setting up a Belkin Wireless Network: Mobility youll no longer need a dedicated computer roomnow you can work on a networked laptop or desktop computer anywhere within your wireless range Easy installation Belkins Setup Assistant makes setup simple Flexibility set up and access printers, computers, and other networking devices from anywhere in your home Easy Expansion the wide range of Belkin networking products let you expand your network to include devices such as printers and gaming consoles No cabling required you can spare the expense and hassle of retrofitting Ethernet cabling throughout the home or office Widespread industry acceptance choose from a wide range of interoperable networking products

Introduction

Placement of your Wireless G Plus MIMO Router

Important Factors for Placement and Setup
Your wireless connection will be stronger the closer your computer is to your Router (or access point). Typical indoor operating range for wireless devices is between 100 and 200 feet. In the same way, your wireless connection and performance will degrade somewhat as the distance between your Router (or access point) and connected devices increases. This may or may not be noticeable to you. As you move further from your Router (or access point), connection speed may decrease. Factors that can weaken signals simply by getting in the way of your networks radio waves are metal appliances or obstructions, and walls. If you have concerns about your networks performance that might be related to range or obstruction factors, try moving the computer to a position between five and 10 feet from the Router (or access point) in order to see if distance is the problem. If difficulties persist even at close range, please contact Belkin Technical Support. Note: While some of the items listed below can affect network performance, they will not prohibit your wireless network from functioning; if you are concerned that your network is not operating at its maximum effectiveness, this checklist may help.

1.

Wireless Router (or Access Point) Placement

Place your Router (or access point), the central connection point of your network, as close as possible to the center of your wireless network devices. To achieve the best wireless network coverage for your wireless clients (i.e., computers enabled by Belkin Wireless Notebook Network Cards, Wireless Desktop Network Cards, and Wireless USB Adapters): Ensure that your Routers (or access points) networking antennas are parallel to each other, and are positioned vertically (toward the ceiling). If your Router (or access point) itself is positioned vertically, point the antennas as much as possible in an upward direction. In multistory homes, place the Router (or access point) on a floor that is as close to the center of the home as possible. This may mean placing the Router (or access point) on an upper floor. Try not to place the Router (or access point) near a cordless 2.4GHz phone.

Introduction
section

2.

Avoid Obstacles and Interference

Avoid placing your Router (or access point) near devices that may emit radio noise, such as microwave ovens. Dense objects that can inhibit wireless communication include: Refrigerators Washers and/or dryers Metal cabinets Large aquariums Metallic-based UV tinted windows If your wireless signal seems weak in some spots, make sure that objects such as these are not blocking the signals path (between your computers and Router or access point).

1 2 3 4 5 6 7 8 9 10

3.

Cordless Phones
If the performance of your wireless network is impaired after attending to the above issues, and you have a cordless phone: Try moving cordless phones away from your Router (or access point) and your wireless-enabled computers. Unplug and remove the battery from any cordless phone that operates on the 2.4GHz band (check manufacturers information). If this fixes the problem, your phone may be interfering. If your phone supports channel selection, change the channel on the phone to the farthest channel from your wireless network. For example, change the phone to channel 1 and move your Router (or access point) to channel 11. See your phones user manual for detailed instructions. If necessary, consider switching to a 900MHz or 5GHz cordless phone.

4.

Choose the Quietest Channel for your Wireless Network

In locations where homes or offices are close together, such as apartment buildings or office complexes, there may be wireless networks nearby that can conflict with yours. Use the Site Survey capabilities found in the Wireless Utility of your wireless adapter to locate any other wireless networks that are available (see your wireless adapters user manual), and move your Router (or access point) and computers to a channel as far away from other networks as possible.

Introduction

Experiment with more than one of the available channels, in order to find the clearest connection and avoid interference from neighboring cordless phones or other wireless devices. For Belkin wireless networking products, use the detailed Site Survey and wireless channel information included with your wireless network card. See your network cards user guide for more information. These guidelines should allow you to cover the maximum possible area with your Router (or access point). Should you need to cover an even wider area, we suggest the Belkin Wireless Range Extender/Access Point.

5.

Secure Connections, VPNs, and AOL

Secure connections typically require a user name and password, and are used where security is important. Secure connections include: Virtual Private Network (VPN) connections, often used to connect remotely to an office network The Bring Your Own Access program from America Online (AOL), which lets you use AOL through broadband provided by another cable or DSL service Most online banking websites Many commercial websites that require a user name and password to access your account Secure connections can be interrupted by a computers power management setting, which causes it to go to sleep. The simplest solution to avoid this is to simply reconnect by rerunning the VPN or AOL software, or by re-logging into the secure website. A second alternative is to change your computers power management settings so it does not go to sleep; however, this may not be appropriate for portable computers. To change your power management setting under Windows, see the Power Options item in the Control Panel. If you continue to have difficulty with Secure Connections, VPNs, and AOL, please review the steps above to be sure you have addressed these issues.

Introduction
section

For more information regarding our networking products, visit our website at www.belkin.com/networking or call Belkin Technical Support at:

1 2 3 4 5 6 7 8 9 10

US: 877-736-5771 800-223-5546 ext. 2263 310-898-1100 ext. 2263 UK: 0845 607 77 87 Australia: 1800 235 546 New Zealand: 0800 235 546 Singapore: 65 64857620 Europe: www.belkin.com/support

Product Overview

Product Features
In minutes you will be able to share your Internet connection and network your computers. The following is a list of features that make your new Belkin Wireless G Plus MIMO Router an ideal solution for your home or small office network.

Works with Both PCs and Mac Computers

The Router supports a variety of networking environments including Mac OS 8.x, 9.x, X v10.x, Linux, Windows 2000, XP, Vista, and others. All that is needed is an Internet browser and a network adapter that supports TCP/IP (the standard language of the Internet).

Front-Panel LED Display

Lighted LEDs on the front of the Router indicate which functions are in operation. Youll know at-a-glance whether your Router is connected to the Internet. This feature eliminates the need for advanced software and status-monitoring procedures.

Web-Based Advanced User Interface

You can set up the Routers advanced functions easily through your web browser, without having to install additional software onto the computer. There are no disks to install or keep track of and, best of all, you can make changes and perform setup functions from any computer on the network quickly and easily.

NAT IP Address Sharing

Your Router employs Network Address Translation (NAT) to share the single IP address assigned to you by your Internet Service Provider while saving the cost of adding additional IP addresses to your Internet service account.

SPI Firewall
Your Router is equipped with a firewall that will protect your network from a wide array of common hacker attacks including IP Spoofing, Land Attack, Ping of Death (PoD), Denial of Service (DoS), IP with zero length, Smurf Attack, TCP Null Scan, SYN flood, UDP flooding, Tear Drop Attack, ICMP defect, RIP defect, and fragment flooding.

Product Overview
1
section

Integrated 10/100 4-Port Switch

The Router has a built-in, four-port network switch to allow your wired computers to share printers, data and MP3 files, digital photos, and much more. The switch features automatic detection so it will adjust to the speed of connected devices. The switch will transfer data between computers and the Internet simultaneously without interrupting or consuming resources.

2 3 4 5 6 7 8 9 10

Universal Plug and Play (UPnP)

UPnP is a technology that offers seamless operation of voice messaging, video messaging, games, and other applications that are UPnP-compliant.

Support for VPN Pass-Through

If you connect to your office network from home using a VPN connection, your Router will allow your VPN-equipped computer to pass through the Router and to your office network.

Built-In Dynamic Host Configuration Protocol (DHCP)

Built-In Dynamic Host Configuration Protocol (DHCP) on-board makes for the easiest possible connection of a network. The DHCP server will assign IP addresses to each computer automatically so there is no need for a complicated networking setup.

Setup Assistant
The Setup Assistant takes the guesswork out of setting up your Router. This automatic software determines your network settings for you and sets up the Router for connection to your Internet Service Provider (ISP). In a matter of minutes, your Router will be up and running on the Internet. Note: Setup Assistant software is compatible with Windows 2000, XP, Vista, and Mac OS X. If you are using another operating system, the Router can be set up using the Alternate Setup Method described in this User Manual (see page 29).

Product Overview

Integrated G Plus MIMO Wireless Access Point

G Plus MIMO is an exciting new wireless technology that achieves data rates up to 54Mbps. Actual throughput is typically lower than the connected data rate and will vary depending on your networking environment.

MAC Address Filtering

For added security, you can set up a list of MAC addresses (unique client identifiers) that are allowed access to your network. Every computer has its own MAC address. Simply enter these MAC addresses into a list using the Web-Based Advanced User Interface and you can control access to your network.

Knowing your Router

1 2
section

Package Contents
Belkin Wireless G Plus MIMO Router Quick Installation Guide Belkin Setup Assistant Software CD Belkin RJ45 Ethernet Networking Cable Power Supply User Manual

3 4 5 6 7 8 9 10

System Requirements
Broadband Internet connection such as a cable or DSL modem with RJ45 (Ethernet) connection At least one computer with an installed network interface adapter TCP/IP networking protocol installed on each computer RJ45 Ethernet networking cable Internet browser

Setup Assistant Software System Requirements

A PC running Windows 2000, XP, or Vista; or a Mac computer running Mac OS X Minimum 64MB RAM Internet browser

Knowing your Router

The Router has been designed to be placed on a desktop. All of the cables exit from the rear of the Router for better organization and utility. The LED indicators are easily visible on the TOP of the Router to provide you with information about network activity and status.

(A)

(B)

(C) (D)

(E)

Wireless G Plus MIMO Router

A. Wireless Network LED

OFF Green Blinking

Wireless network is OFF Wireless network is ready Indicates wireless activity

B.

Wired Computer Status LEDs

These LEDs are labeled 14 and correspond to the numbered ports on the rear of the Router. When a computer is properly connected to one of the wired computer ports on the rear of the Router, the LED will light. When information is being sent over the port, the LED blinks rapidly.
OFF Green Blinking No device is linked to the port 10Base-T device connected Port activity

10

Knowing your Router

1 2
section

C.

Modem/WAN Status LED

This LED lights in GREEN to indicate that your modem is connected properly to the Router. It blinks rapidly when information is being sent over the port between the Router and the modem.
OFF Solid Green Blinking Green No WAN link Good WAN link WAN activity

3 4 5 6 7 8 9 10

D.

Internet/Connected LED
This unique LED shows you when the Router is connected to the Internet. When the light is OFF, the Router is NOT connected to the Internet. When the light is blinking, the Router is attempting to connect to the Internet. When the light is solid GREEN, the Router is connected to the Internet. When using the Disconnect after x minutes feature, this LED becomes extremely useful in monitoring the status of your Routers connection.
OFF Blinking Green Solid Green Router is not connected to the Internet Router is attempting to connect to the Internet Router is connected to the Internet

E.

LED Power/Ready

When you apply power to the Router or restart it, a short period of time elapses while the Router boots up. During this time, the Power/Ready LED blinks. When the Router has completely booted up, the Power/ Ready LED becomes a SOLID light, indicating the Router is ready for use.
OFF Blinking Green Solid Green Router is OFF Router is booting up Router is ready

11

Knowing your Router

Rear Panel
(F) (G) (H) (I) (J)

F. G.

Power Jack Black

Connect the included 12V/1A DC power supply to this jack.

Connections to Computers (Wired Computer Ports) Gray

Connect your wired (non-wireless) computers to these ports. These ports are RJ45, 10/100 auto-negotiation, auto-uplinking ports for standard UTP category 5 or 6 Ethernet cable. The ports are labeled 1 through 4. These ports correspond to the numbered LEDs on the front of the Router.

H.

Connection to Modem (Modem Port) Yellow

This port is for connection to your cable or DSL modem. Use the cable that was provided with the modem to connect the modem to this port. Use of a cable other than the cable supplied with the cable modem may not work properly.

12

Knowing your Router

1 2
section

I.

Reset Button
The Reset button is used in rare cases when the Router may function improperly. Resetting the Router will restore the Routers normal operation while maintaining the programmed settings. You can also restore the factory default settings by using the Reset button. Use the restore option in instances where you may have forgotten your custom password.

3 4 5 6 7 8 9 10

(a) Resetting the Router

Push and release the Reset button. The lights on the Router will momentarily flash. The Power/Ready light will begin to blink. When the Power/Ready light becomes solid again, the reset is complete.

(b) Restoring the Factory Defaults

Press and hold the Reset button for at least 10 seconds, then release it. The lights on the Router will momentarily flash. The Power/Ready light will begin to blink. When the Power/Ready light becomes solid again, the restore is complete.

J.

Push Button White

This button is used for the Wi-Fi Protected SetupTM feature. Please refer to the Changing the Wireless Security Settings section.

13

Connecting and Configuring your Router

Verify the contents of your box. You should have the following:
Belkin Wireless G Plus MIMO Router Category 5 Networking Cable (for connecting the Router to the computer) Power Supply Belkin Setup Assistant Software CD User Manual

Modem Requirements
Your cable or DSL modem must be equipped with an RJ45 Ethernet port. Many modems have both an RJ45 Ethernet port and a USB connection. If you have a modem with both Ethernet and USB, and are using the USB connection at this time, you will be instructed to use the RJ45 Ethernet port during the installation procedure. If your modem has only a USB port, you can request a different type of modem from your ISP, or you can, in some cases, purchase a modem that has an RJ45 Ethernet port on it.

Ethernet Setup Assistant

USB

Belkin has provided our Setup Assistant software to make installing your Router a simple and easy task. You can use it to get your Router up and running in minutes. The Setup Assistant requires that your Windows 2000, XP, or Vista computer be connected directly to your cable or DSL modem and that the Internet connection is active and working at the time of installation. If it is not, you must use the Alternate Setup Method section of this User Manual to configure your Router. Additionally, if you are using an operating system other than Windows 2000, XP, or Vista, you must set up the Router using the Alternate Setup Method section of this User Manual.

14

Connecting and Configuring your Router

1 2 3
section

Step 1

Hardware Connections Follow the Quick Installation Guide (QIG) 1.1 Unplug your modems power

cord. Place the Router next to the modem with the antennas raised.

4 5

1.2 Locate the networking cable

that connects your modem and computer. Unplug that cable from your modem, and plug it into any gray port on the back of the Router.

6 7 8

1.3 Find your new networking cable

(included in the box with your Router) and connect it to the yellow port on the back of the Router. Connect the other end to your modem, in the port thats now free.

9 10

1.4 Plug in your modems power cord.

Wait 60 seconds for the modem to start up. Plug the Routers power supply into the black port on the back. Plug the other end into the wall outlet.

1.5 Wait 20 seconds for the Router to

start up. Look at the display on the front of the Router. Make sure the Wired and Router icons are lit up in blue. If they are not, recheck your connections.

15

Connecting and Configuring your Router

Step 2 2.1

Set Up the Router Run the Setup Assistant Software

Shut down any programs that are running on your computer at this time.Turn off any firewall or Internet-connection-sharing software on your computer. Insert the CD into your computer. The Setup Assistant will automatically appear on your computers screen within 15 seconds. Click on Go to run the Setup Assistant. Follow the instructions there.

2.2

IMPORTANT: Run the Setup Assistant from the computer that is directly connected to the Router from Step 1.2.

Note for Windows Users: If the Setup Assistant does not start up automatically, double-click on the My Computer icon on your desktop, select your CD-ROM drive, and double-click on the file named SetupAssistant.

16

Connecting and Configuring your Router

1 2 3
section

2.3

Confirmation Screen
Verify that you have completed all setup steps by checking the box to the right of the arrow. Click Next to continue.

4 5 6 7 8 9 10

17

Connecting and Configuring your Router

2.4

Progress Screen
Setup Assistant will show you a progress screen each time a step in the setup has been completed.

2.5

Checking Settings
The Setup Assistant will now examine your computers network settings and gather information needed to complete the Routers connection to the Internet.

18

Connecting and Configuring your Router

1 2 3
section

2.6

Verifying Hardware Connections

The Setup Assistant will now verify your hardware connection.

4 5 6 7
2.7 Naming your Wireless Network
The Setup Assistant will display the default wireless-network name or Service Set Identifier (SSID). This is the name of your wireless network to which your computers or devices with wireless network adapters will connect. You can either use the default or change it to something unique. Write down this name for future reference. Click Next to continue.

8 9 10

19

Connecting and Configuring your Router

2.8

Requesting Internet Account Info (if needed)

If your Internet account requires a login and password, you will be prompted with a screen similar to the illustration below. Select your country or ISP from the drop-down boxes.

20

Connecting and Configuring your Router

1 2 3
section

2.9

Configuring the Router

The Setup Assistant will now configure your Router by sending data to the Router and restarting it. Wait for the on-screen instructions. Note: Do not disconnect any cable or power off the Router while the Router is rebooting. Doing so will render your Router inoperable.

4 5 6 7 8 9 10

21

Connecting and Configuring your Router

2.10 Checking Internet Connection

We are almost done. The Setup Assistant will now check your connection to the Internet.

22

Connecting and Configuring your Router

1 2 3
section

4 5 6
Congratulations You have finished installing your new Belkin Router. You will see the Congratulations screen when your Router can connect to the Internet. You can begin surfing by opening your browser and going to any website.

7 8 9 10

23

Connecting and Configuring your Router

You can use the Setup Assistant to set up your other wired and wireless computers to connect to the Internet by clicking Next. If you decide to add computers to your Router later, select Exit the Assistant and then click Next.

24

Connecting and Configuring your Router

1 2 3
section

4 5 6
`

Troubleshooting
If the Setup Assistant is not able to connect to the Internet, you will see the following screen. Follow the on-screen instructions to go through the troubleshooting steps.

7 8 9 10

25

Connecting and Configuring your Router

Optional: Assistance Connecting Other Computers

This optional step will help you to connect additional wired and wireless computers to your network. Follow the on-screen instructions.

At this point, your Router is set up and working properly. It is now time to connect your other computers.

Connecting computers wirelessly

Computers with wireless network adapters can use this network. If you still need to install those adapters, do this now. Then follow their instructions on how to connect. When you do so, look for your network: Johns Home Wi-Fi.

26

Connecting and Configuring your Router

1 2 3
section

Connecting computers with wired cables

Computers with wired network adapters can use this network. If you still need to install those adapters, do this now. Then simply connect an Ethernet cable between your computers network port and one of the available LAN ports (labeled connections to computers) on the back of this Router.]

4 5 6 7 8 9 10

27

Connecting and Configuring your Router

Congratulations

Once you have verified that your other wired and wireless computers are properly connected, your network is set up and working. You can now surf the Internet. Click Next to take you back to the main menu.

28

Alternate Setup Method

1
Step 1 1.1 1.2 Connecting your Gateway Router
Turn off the power to your modem by unplugging the power supply from the modem. Locate the network cable that is connected between your modem and your computer and unplug it from your computer, leaving the other end connected to your modem. Plug the loose end of the cable you just unplugged into the port on the back of the Router labeled Internet/WAN. Connect the included network cable from the back of the computer to one of the ports labeled 14. Note: It does not matter which numbered port you choose. Turn your cable or DSL modem on by reconnecting the power supply to the modem. Before plugging the power cord into the Router, plug the cord into the wall, then plug the cord into the Routers power jack.

2 3 4
section

1.3 1.4

5 6 7 8 9 10

1.5 1.6

To power adapter

Cable or DSL modem

Mac or PC computer that was originally connected to the cable or DSL modem

Supplied Blue Ethernet cable (to computer)

Existing network cable (that came with modem)

29

Alternate Setup Method

1.7

Verify that your modem is connected to the Router by checking the lights on the TOP of the Router. The green light labeled WAN should be ON if your modem is connected correctly to the Router. If it is not, recheck your connections. Verify that your computer is connected properly to the Router by checking the lights labeled LAN 1,2,3,4. The light which corresponds to the numbered port connected to your computer should be ON, if your computer is connected properly. If it is not, recheck your connections.

1.8

Step 2:

Set your Computers Network Settings to Work with a DHCP Server

See the section in this User Manual called Manually Configuring Network Settings for directions.

Step 3:

Conguring the Router Using the Web-Based Advanced User Interface

Using your Internet browser, you can access the Routers Web-Based Advanced User Interface. In your browser, type 192.168.2.1 (do not type in anything else such as http:// or www). Then press the Enter key.

30

Alternate Setup Method

1 2 3 4
section

Logging into the Router

You will see the Routers home page in your browser window. The home page is visible to any user who wants to see it. To make any changes to the Routers settings, you have to log in. Clicking the Login button or clicking on any one of the links on the home page will take you to the login screen. The Router ships with no password entered. In the login screen, leave the password blank and click the Submit button to log in.

5 6 7 8 9
Logging out of the Router
One computer at a time can log into the Router for the purposes of making changes to the settings of the Router. Once a user has logged in to make changes, there are two ways that the computer can be logged out. Clicking the Logout button will log the computer out. The second method is automatic. The login will time out after a specified period of time. The default login time-out is 10 minutes. This can be changed from one to 99 minutes. For more information, see the section in this manual titled Changing the Login Time-Out Setting.

10

31

Alternate Setup Method

Understanding the Web-Based Advanced User Interface

The home page is the first page you will see when you access the Advanced User Interface (UI). The home page shows you a quick view of the Routers status and settings. All advanced setup pages can be reached from this page.

1.

Quick-Navigation Links
You can go directly to any of the Routers advanced UI pages by clicking directly on these links. The links are divided into logical categories and grouped by tabs to make finding a particular setting easier to find. Clicking on the purple header of each tab will show you a short description of the tabs function.

2.

Home Button
The home button is available in every page of the UI. Pressing this button will take you back to the home page.

3.

Internet Status Indicator

This indicator is visible in all pages of the Router, indicating the connection status of the Router. When the indicator says connection OK in GREEN, the Router is connected to the Internet. When the Router is not connected to the Internet, the indicator will read no connection in RED. The indicator is automatically updated when you make changes to the settings of the Router. (10) (2)(5) (4) (3)

(9)
(1) (7) (8)

(6)

32

Alternate Setup Method

1 2 3 4
section

4.

Login/Logout Button
This button enables you to log in and out of the Router with the press of one button. When you are logged into the Router, this button will change to read Logout. Logging into the Router will take you to a separate login page where you will need to enter a password. When you are logged into the Router, you can make changes to the settings. When you are finished making changes, you can log out of the Router by clicking the Logout button. For more information about logging into the Router, see the section called Logging into the Router.

5.

Help Button
The Help button gives you access to the Routers help pages. Help is also available on many pages by clicking more info next to certain sections of each page.

5 6 7 8 9 10

6.

LAN Settings

Shows you the settings of the Local Area Network (LAN) side of the Router. Changes can be made to the settings by clicking on any one of the links (IP Address, Subnet Mask, DHCP Server) or by clicking the LAN quick-navigation link on the left side of the screen.

7.

Features

Shows the status of the Routers NAT, firewall, and wireless features. Changes can be made to the settings by clicking on any one of the links or by clicking the quick-navigation links on the left side of the screen.

8.

Internet Settings

Shows the settings of the Internet/WAN side of the Router that connects to the Internet. Changes to any of these settings can be made by clicking on the links or by clicking on the Internet/WAN quick-navigation link on the left side of the screen.

9.

Version Info

Shows the firmware version, boot-code version, hardware version, and serial number of the Router. The page you are on can be identified by this name. This User Manual will sometimes refer to pages by name. For instance LAN > LAN Settings refers to the LAN Settings page.

10. Page Name

33

Alternate Setup Method

Step 4:

Conguring your Router for Connection to your Internet Service Provider (ISP)

The Internet/WAN tab is where you will set up your Router to connect to your Internet Service Provider (ISP). The Router is capable of connecting to virtually any ISPs system provided you have correctly configured the Routers settings for your ISPs connection type. Your ISP connection settings are provided to you by your ISP. To configure the Router with the settings that your ISP gave you, click Connection Type (A) on the left side of the screen. Select the connection type you use. If your ISP gave you DNS settings, clicking DNS (B) allows you to enter DNS address entries for ISPs that require specific settings. Clicking MAC Address (C) will let you clone your computers MAC address or type in a specific WAN MAC address, if required by your ISP. When you have finished making settings, the Internet Status indicator will read connection OK if your Router is set up properly.

(A) (B) (C)

34

Alternate Setup Method

1 2 3 4
section

Setting your Connection Type

From the Connection Type page, you can select the type of connection you use. Select the type of connection you use by clicking the button (1) next to your connection type and then clicking Next (2).

5
(1)

6
(2)

7 8 9 10

35

Alternate Setup Method

Setting your Internet Service Provider (ISP) Connection Type to Dynamic IP

A dynamic connection type is the most common connection type found with cable modems. Setting the connection type to dynamic in many cases is enough to complete the connection to your ISP. Some dynamic connection types may require a host name. You can enter your host name in the space provided if you were assigned one. Your host name is assigned by your ISP. Some dynamic connections may require that you clone the MAC address of the PC that was originally connected to the modem.

1.

Host Name
This space is provided to enter a host name that needs to be visible to your ISP. Enter your host name here and click Apply Changes. If your ISP did not assign you a host name, or you are not sure, leave this blank.

2.

Change WAN MAC Address

If your ISP requires a specific MAC address to connect to the service, you can enter a specific MAC address or clone the current computers MAC address through this link.

(1)

(2)

36

Alternate Setup Method

1 2 3 4
section

Setting your Internet Service Provider (ISP) Connection Type to Static IP

A static IP address connection type is less common than other connection types. If your ISP uses static IP addressing, you will need your IP address, subnet mask, and ISP gateway address. This information is available from your ISP or on the paperwork that your ISP left with you. Type in your information, then click Apply Changes. After you apply the changes, the Internet Status indicator will read connection OK if your Router is set up properly.

1. 2. 3. 4.

IP Address
Provided by your ISP. Enter your IP address here.

5 6 7 8 9 10

Subnet Mask
Provided by your ISP. Enter your subnet mask here.

ISP Gateway Address

Provided by your ISP. Enter the ISP gateway address here.

My ISP Provides More Than One Static IP Address

If your ISP assigns you more than one static IP address, your Router is capable of handling up to five static WAN IP addresses. Select My ISP provides more than one static IP address and enter your additional addresses.

(1) (2) (3) (4)

37

Alternate Setup Method

Setting your ISP Connection Type to PPPoE

Most DSL providers use PPPoE as the connection type. If you use a DSL modem to connect to the Internet, your ISP may use PPPoE to log you into the service. If you have an Internet connection in your home or small office that doesnt require a modem, you may also use PPPoE.

Your connection type is PPPoE if: 1) Your ISP gave you a user name and password, which is required to
connect to the Internet.

2) Your ISP gave you software such as WinPOET or Enternet300 that you
use to connect to the Internet.

3) You have to double-click on a desktop icon other than your browser to

get on the Internet.

(1) (2) (4) (5) (3)

38

Alternate Setup Method

1 2 3 4
section

1.

User Name
This space is provided to type in your user name that was assigned by your ISP.

2.

Password
Type in your password and retype it into the Retype Password box to confirm it.

3.

Service Name
A service name is rarely required by an ISP. If you are not sure if your ISP requires a service name, leave this blank.

4.

MTU
The MTU setting should never be changed unless your ISP gives you a specific MTU setting. Making changes to the MTU setting can cause problems with your Internet connection including disconnection from the Internet, slow Internet access, and problems with Internet applications working properly.

5 6 7 8 9 10

5.

Disconnect after X...

The Disconnect feature is used to automatically disconnect the Router from your ISP when there is no activity for a specified period of time. For instance, placing a check mark next to this option and entering 5 into the minute field will cause the Router to disconnect from the Internet after five minutes of no Internet activity. This option should be used if you pay for your Internet service by the minute.

39

Alternate Setup Method

Setting your Internet Service Provider (ISP) Connection Type to Point-to-Point Tunneling Protocol (PPTP) [European Countries Only]
Some ISPs require a connection using PPTP protocol, a type of connection most common in European countries. This sets up a direct connection to the ISPs system. Type in the information provided by your ISP in the space provided. When you have finished, click Apply Changes. After you apply the changes, the Internet Status indicator will read connection OK if your Router is set up properly.

(1) (2) (3) (4) (5) (6) (7) (8)

1. 2.

PPTP Account
Provided by your ISP. Enter your PPTP account name here.

PPTP Password
Type in your password and retype it into the Retype Password box to confirm it.

3. 4. 5. 6.

Host Name
Provided by your ISP. Enter your host name here

Server IP Address
Provided by your ISP. Enter your server IP address here.

My IP Address
Provided by your ISP. Enter the IP address here

My Subnet Mask
Provided by your ISP. Enter the IP address here.

40

Alternate Setup Method

1 2 3 4
section

7.

Connection ID (optional)
Provided by your ISP. If your ISP did not give you a connection ID, leave this blank.

8.

Disconnect after X....

The Disconnect feature is used to automatically disconnect the Router from your ISP when there is no activity for a specified period of time. For instance, placing a check mark next to this option and entering 5 into the minute field will cause the Router to disconnect from the Internet after five minutes of no Internet activity. This option should be used if you pay for your Internet service by the minute.

5 6 7 8 9 10

41

Alternate Setup Method

Setting your Connection Type if You Are a Telstra BigPond User [Australia Only]
Your user name and password are provided to you by Telstra BigPond. Enter this information below. Choosing your state from the drop-down menu (6) will automatically fill in your login server IP address. If your login server address is different than one provided here, you may manually enter the login server IP address by placing a check in the box next to User decide login server manually (4) and type in the address next to Login Server (5). When you have entered all of your information, click Apply Changes. After you apply the changes, the Internet Status indicator will read connection OK if your Router is set up properly.

(1)

(6) (2) (3) (4) (5)

1.

Select your State

Select your state from the drop-down menu (6). The Login Server box will automatically be filled in with an IP address. If for some reason this address does not match the address that Telstra has given, you can manually enter the login server address. See User decide login server manually (4).

2. 3.

User Name
Provided by your ISP. Type in your user name here.

Password
Type in your password and retype it into the Retype Password box to confirm it.

4.

User Decide Login Server Manually

If your login server IP address is not available in the Select Your State dropdown menu (6), you may manually enter the login server IP address by placing a check in the box next to User decide login server manually and type in the address next to Login Server (5).

42

Alternate Setup Method

1 2 3 4
section

Setting Custom Domain Name Server (DNS) Settings

A Domain Name Server is a server located on the Internet that translates Universal Resource Locaters (URLs) like www.belkin.com to IP addresses. Many Internet Service Providers (ISPs) do not require you to enter this information into the Router. The Automatic from ISP box (1) should be checked if your ISP did not give you a specific DNS address. If you are using a static IP connection type, then you may need to enter a specific DNS address and secondary DNS address for your connection to work properly. If your connection type is dynamic or PPPoE, it is likely that you do not have to enter a DNS address. Leave the Automatic from ISP box checked. To enter the DNS address settings, uncheck the Automatic from ISP box and enter your DNS entries in the spaces provided. Click Apply Changes to save the settings.

5 6 7

(1)

(2)

8 9 10

43

Alternate Setup Method

Configuring your WAN Media Access Controller (MAC) Address

All network components including cards, adapters, and routers, have a unique serial number called a MAC address. Your Internet Service Provider (ISP) may record the MAC address of your computers adapter and only let that particular computer connect to the Internet service. When you install the Router, its own MAC address will be seen by the ISP and may cause the connection not to work. Belkin has provided the ability to clone (copy) the MAC address of the computer into the Router. This MAC address, in turn, will be seen by the ISPs system as the original MAC address and will allow the connection to work. If you are not sure whether your ISP needs to see the original MAC address, simply clone the MAC address of the computer that was originally connected to the modem. Cloning the address will not cause any problems with your network.

Cloning your MAC Address

To clone your MAC address, make sure that you are using the computer that was ORIGINALLY CONNECTED to your modem before the Router was installed. Click MAC Address on the navigation link and then the Clone button. Click Apply Changes. Your MAC address is now cloned to the Router.

Entering a Specific MAC Address

In certain circumstances you may need a specific WAN MAC address. You can manually enter one in the MAC Address page. Type in a MAC address in the spaces provided (1) and click Apply Changes to save the changes. The Routers WAN MAC address will now be changed to the MAC address you specified.

(1)

44

Using the Web-Based Advanced User Interface

1 2 3
You will see the Routers home page in your browser window.

Using your Internet browser, you can access the Routers Web-Based Advanced User Interface. In your browser, type 192.168.2.1 (do not type in anything else such as http:// or www) then press the Enter key.

4 5
section

Viewing the LAN Settings

Clicking on the header of the LAN tab (1) will take you to the LAN tabs header page. A quick description of the functions can be found here. To view the settings or make changes to any of the LAN settings, click on LAN Settings (2) or to view the list of connected computers, click on DHCP client list (3). (1) (2) (3)

6 7 8 9 10

45

Using the Web-Based Advanced User Interface

Changing LAN Settings

All settings for the internal LAN setup of the Router can be viewed and changed here.

(1) (2) (3) (4) (5) (6)

1.

IP Address
The IP address is the internal IP address of the Router. The default IP address is 192.168.2.1. To access the advanced setup interface, type this IP address into the address bar of your browser. This address can be changed if needed. To change the IP address, type in the new IP address and click Apply Changes. The IP address you choose should be a non-routable IP. Examples of a nonroutable IP are: 192.168.x.x (where x is anything between 0 and 255) 10.x.x.x (where x is anything between 0 and 255)

2.

Subnet Mask
There is no need to change the subnet mask. This is a unique, advanced feature of your Belkin Router. It is possible to change the subnet mask if necessary; however, do NOT make changes to the subnet mask unless you have a specific reason to do so. The default setting is 255.255.255.0.

46

Using the Web-Based Advanced User Interface

1 2 3 4 5
section

3.

DHCP Server
The DHCP server function makes setting up a network very easy by assigning IP addresses to each computer on the network automatically. The default setting is On. The DHCP server can be turned OFF if necessary; however, in order to do so you must manually set a static IP address for each computer on your network. To turn off the DHCP server, select Off and click Apply Changes.

4.

IP Pool
The range of IP addresses set aside for dynamic assignment to the computers on your network. The default is 2100 (99 computers). If you want to change this number, you can do so by entering a new starting and ending IP address and clicking on Apply Changes. The DHCP server can assign 100 IP addresses automatically. This means that you cannot specify an IP address pool larger than 100 computers. For example, starting at 50 means you have to end at 150 or lower so as not to exceed the 100-client limit. The starting IP address must be lower in number than the ending IP address.

6 7 8 9 10

5.

Lease Time
The length of time the DHCP server will reserve the IP address for each computer. We recommend that you leave the lease time set to Forever. The default setting is Forever, meaning that any time a computer is assigned an IP address by the DHCP server, the IP address will not change for that particular computer. Setting lease times for shorter intervals such as one day or one hour frees IP addresses after the specified period of time. This also means that a particular computers IP address may change over time. If you have set any of the other advanced features of the Router such as DMZ or client IP filters, these are dependent on the IP address. For this reason, you will not want the IP address to change.

6.

Local Domain Name

The default setting is Belkin. You can set a local domain name (network name) for your network. There is no need to change this setting unless you have a specific advanced need to do so. You can name the network anything you want such as MY NETWORK.

47

Using the Web-Based Advanced User Interface

Viewing the DHCP Client List Page

You can view a list of the computers (known as clients), which are connected to your network. You are able to view the IP address (1) of the computer, the host name (2) (if the computer has been assigned one), and the MAC address (3) of the computers network interface card (NIC). Pressing the Refresh (4) button will update the list. If there have been any changes, the list will be updated.

(3) (1) (2) (4)

48

Using the Web-Based Advanced User Interface

1 2 3 4 5
section

Configuring the Wireless Network Settings

The Wireless tab lets you make changes to the wireless network settings. From this tab you can make changes to the wireless network name (SSID), operating channel, encryption security settings, and configure the Router to be used as an access point.

6 7 8 9 10

49

Using the Web-Based Advanced User Interface

Changing the Wireless Network Name (SSID)

To identify your wireless network, a name called the SSID (Service Set Identifier) is used. The SSID is your network name. The default network name of the Router is Belkin G Plus MIMO_ followed by six digits that are unique to your Router. Your network name will look something like Belkin G Plus MIMO_012345. You can change this to anything you choose, or you can leave it unchanged. Keep in mind, if you decide to change your wireless network name, and there are other wireless networks operating in your area, your network name needs to be different from other wireless networks that may be operating in your area. To change the SSID, type in the SSID that you want to use in the SSID field (1) and click Apply Changes. The change is immediate. If you make a change to the SSID, your wireless-equipped computers may also need to be reconfigured to connect to your new network name. Refer to the documentation of your wireless network adapter for information on making this change.

(1)

50

Using the Web-Based Advanced User Interface

1 2 3 4 5
section

Using the Wireless Mode Switch

This switch allows you to set the Routers wireless modes. There are three modes.

1) 802.11g only
Setting the Router to this mode will allow only G Plus MIMO and 802.11g-compliant devices to join the network, keeping out any slower 802.11b devices.

2) 802.11g & 802.11b

Setting the Router to this mode will let G Plus MIMO-, 802.11g-, and 802.11b-compliant devices to join the network.

3) Off
This mode will turn OFF the Routers access point, so no wireless devices can join the network. Turning off the wireless function of your Router is a great way to secure your network when you are away from home for a long period of time, or dont want to use the wireless feature of the Router at a certain time.

6 7 8 9 10

51

Using the Web-Based Advanced User Interface

Changing the Wireless Channel

There are a number of operating channels you can choose from. In the United States, there are 11 channels. In the United Kingdom and most of Europe, there are 13 channels. In a small number of other countries, there are other channel requirements. Your Router is configured to operate on the proper channels for the country you reside in. The channel can be changed if needed. If there are other wireless networks operating in your area, your network should be set to operate on a channel that is different than the other wireless networks.

Auto Channel Selection Feature and Changing the Channel

For best performance, your Router should use a channel that is at least five channels away from the other wireless networks in the area. For instance, if another network is operating on channel 11, then set your network to channel 6 or below. The auto channel selection mode will choose the clearest channel to operate on when the Router is first powered up. Your Router ships from the factory with the auto channel feature enabled. You can manually select a channel if you wish; however, it is recommended to use the auto channel mode. To change the channel, select the channel from the drop-down list. Click Apply Changes. The change is immediate.

52

Using the Web-Based Advanced User Interface

1 2 3 4 5
section

Using the Broadcast SSID Feature

Note: This advanced feature should be employed by advanced users only. For security, you can choose not to broadcast your networks SSID. Doing so will keep your network name hidden from computers that are scanning for the presence of wireless networks. To turn off the broadcast of the SSID, remove the check mark from the box next to Broadcast SSID, and then click Apply Changes. The change is immediate. Each computer now needs to be set to connect to your specific SSID; an SSID of ANY will no longer be accepted. Refer to the documentation of your wireless network adapter for information on making this change.

Protected Mode Switch

Protected mode will ensure proper operation of 802.11g devices on your G Plus MIMO network when 802.11b devices are present or when there is heavy 802.11b traffic in the operating environment. If you are using a mix of Belkin G Plus MIMO Wireless Cards and 802.11b or 802.11g cards on your network, protected mode should be used. If you are in an environment where there is no other (or very little) 802.11b wireless network traffic, best 802.11g performance may be achieved with protected mode OFF. If you are operating in an environment with HEAVY 802.11b traffic or interference, best 802.11g performance may be achieved with protected mode ON. Wireless G Plus MIMO performance is not affected by this setting.

6 7 8 9 10

Changing the Wireless Security Settings

Your Router is equipped with the latest security standard called Wi-Fi Protected AccessTM 2 (WPA2TM) and the legacy security standard called Wired Equivalent Privacy (WEP). Your Router also supports the Wi-Fi Protected Setup (WPS) specification, which simplifies the setup of a wireless network. WPS uses familiar methodologies, such as typing in a Personal Identification Number (PIN) or pushing a button, to enable users to automatically configure network names and strong WPATM/WPA2 data encryption and authentication. By default, wireless security is disabled. To enable security, you will need to determine which standard you want to use. To access the security settings, click Security on the Wireless tab.

Using Wi-Fi Protected SetupTM

WPS uses WPA2 (described on page 57) for encryption. It does not provide additional security, but rather, standardizes the method for securing your wireless network. You may use either the Push Button Configuration (PBC) method or PIN method to allow a device access to your wireless network. Conceptually, the two methods work as follows: PBC: Push and hold the WPS button located on the back of your Router for three seconds. Then, initiate the WPS procedure on the client device within two minutes. Refer to your clients documentation on this procedure. Pushing the PBC button will automatically enable WPS. The client has now been securely added to your wireless network.

53

Using the Web-Based Advanced User Interface

PIN: The client device has a PIN number (either four or eight digits) that is associated with WPS. Enable WPS through the screen illustrated below. Enter the clients PIN into the Routers internal registrar (accessed through this screen). The client will be automatically enrolled into your wireless network within two minutes.

(1)

(2) (3)

(4) (5)
1. Wi-Fi Protected Setup (WPS): Enabled or Disabled. 2. Personal Identification Number (PIN) Method: In this method, a wireless client wishing to access your network must supply a 4- or 8-digit PIN to the Router. After clicking Enroll, you must start the WPS handshaking procedure from the client within two minutes. 3. Router PIN: If an external registrar is available, you may enter in the Routers PIN to the registrar. Click Generate New PIN to change the PIN from the default value. Click Restore Default PIN to reset the PIN value. 4. Push Button Configuration (PBC) Method: PBC is an alternate method to connect to a WPS network. Push the PBC button located on the back of the Router for three seconds, and then initiate the PBC on the client device. Alternatively, push the Start PBC soft button to start this process. 5. Manual Configuration Method: This section lists the default security settings to be set up if not using WPS.

54

Using the Web-Based Advanced User Interface

1 2 3 4 5
section

WPA2 Requirements
IMPORTANT: In order to use WPA2 security, all your computers and wireless client adapters must be upgraded with patches, driver, and client utility software that supported WPA2. At the time of this User Manuals publication, a couple security patches are available, for free download, from Microsoft. These patches work only with the Windows XP operating system. Other operating systems are not supported at this time. For Windows XP computers that do not have Service Pack 2 (SP2), a file from Microsoft called Windows XP Support Patch for Wireless Protected Access (KB 826942) is available for free download at http://support. microsoft.com/?kbid=826942 For Windows XP with Service Pack 2, Microsoft has released a free download to update the wireless client components to support WPA2 (KB893357). The update is available from: http://support.microsoft.com/ default.aspx?scid=kb;en-us;893357 IMPORTANT: You also need to ensure that all your wireless client cards/ adapters support WPA2, and that you have downloaded and installed the latest driver. Most of the Belkin wireless cards have driver updates available for download from the Belkin support site: www.belkin.com/networking.

6 7 8 9 10

Setting WPA/WPA2-Personal (PSK)

Like WPA security, WPA2 is available in both WPA2-Personal (PSK) mode and WPA2-Enterprise (RADIUS) mode. Typically, WPA2-Personal (PSK) is the mode that will be used in a home environment, while WPA2-Enterprise (RADIUS) is implemented in a business environment where an external radius server distributes the network key to the clients automatically. This guide will focus on WPA2-Personal (PSK) usage. Please refer to the User Manual for more information about wireless security and different types of wireless security.

1. After youve set up your Router, go to the Security page under

Wireless and select WPA/WPA2-Personal (PSK) from the Security Mode drop-down menu.

2. For Authentication, select WPA-PSK, WPA2-PSK, or

WPA-PSK + WPA2-PSK. This setting will have to be identical on the wireless clients that you set up. WPA-PSK + WPA2-PSK mode will allow the Router to support clients running either WPA or WPA2 security.

55

Using the Web-Based Advanced User Interface

3. For Encryption Technique, select TKIP, AES, or TKIP+AES. This

setting will have to be identical on the wireless clients that you set up.

4. Enter your pre-shared key (PSK). This can be from eight to 63 characters
and can be letters, numbers, or symbols. This same key must be used on all of the wireless clients that you set up. For example, your PSK might be something like: Smith family network key. Click Apply Changes to finish. You must now set all wireless clients to match these settings.

IMPORTANT: Make sure your wireless computers are updated to work with WPA2 and have the correct settings to get proper connection to the Router.

56

Using the Web-Based Advanced User Interface

1 2 3 4 5
section

Setting WPA Security

Note: To use WPA security, your wireless network cards must be equipped with software that supports WPA. At the time this User Manual was published, a security patch from Microsoft is available for free download. This patch works only with Windows XP. Your Router supports WPA-PSK (no server). WPA-PSK uses what is known as a pre-shared key as the security key. A pre-shared key is basically a password that is between eight and 39 characters long. It can be a combination of letters, numbers, or characters. Each client uses the same key to access the network. Typically this is the mode that will be used in a home environment.

Setting WPA-PSK 1. From the Security Mode drop-down menu, select WPA-PSK (no
server).

6 7 8 9 10

2. For Encryption Technique, select TKIP or AES. This setting will

have to be identical on the clients that you set up.

3. Enter your pre-shared key. This can be from eight to 39 characters

and can be letters, numbers, or symbols. This same key must be used on all of the clients that you set up.

4. Click Apply Changes to finish. You must now set all clients to
match these settings.

57

Using the Web-Based Advanced User Interface

Setting WEP Encryption

Note to Mac users: The Passphrase option will not operate with Apple AirPort. To configure encryption for your Mac computer, set the encryption using the manual method described in the next section.

1. Select 128-bit WEP or 64-bit WEP from the drop-down menu

2. After selecting your WEP encryption mode, you can enter you WEP
key manually by typing in the hex WEP key manually, or you can type a passphrase in the PassPhrase field and click Generate to create a WEP key from the passphrase. Click Apply Changes to finish. You must now set all of your clients to match these settings.

3. Encryption in the Router is now set. Each of your computers on your

wireless network will now need to be configured with the same passphrase. Refer to the documentation of your wireless network adapter for information on making this change.

58

Using the Web-Based Advanced User Interface

1 2 3 4 5
section

Using a Hexadecimal Key

A hexadecimal key is a mixture of numbers and letters from AF and 09. 64-bit keys are 10 digits long and can be divided into five two-digit numbers. 128-bit keys are 26 digits long and can be divided into 13 two-digit numbers. For instance:

AF 0F 4B C3 D4 = 64-bit key C3 03 0F AF 0F 4B B2 C3 D4 4B C3 D4 E7 = 128-bit key

In the boxes below, make up your key by writing in two characters between AF and 09. You will use this key to program the encryption settings on your Router and your wireless computers.

6 7 8

Note to Mac users: Original Apple AirPort products support 64-bit encryption only. Apple AirPort 2 products can support 64-bit or 128-bit encryption. Please check your product to see which version you are using. If you cannot configure your network with 128-bit encryption, try 64-bit encryption.

9 10

59

Using the Web-Based Advanced User Interface

Using the Access Point Mode

Note: This advanced feature should be employed by advanced users only. The Router can be configured to work as a wireless network access point. Using this mode will defeat the NAT IP sharing feature and DHCP server. In AP mode, the Router will need to be configured with an IP address that is in the same subnet as the rest of the network that you will bridge to. The default IP address is 192.168.2.254 and subnet mask is 255.255.255.0. These can be customized for your need.

1. Enable the AP mode my selecting Enable in the Use as Access

Point only page. When you select this option, you will be able to change the IP settings.

2. Set your IP settings to match your network. Click Apply Changes. 3. Connect a cable from the LAN port on the Router to your
existing network. The Router is now acting as an access point. To access the Router advanced user interface again, type the IP address you specified into your browsers navigation bar. You can set the encryption settings, MAC address filtering, SSID, and channel normally.

60

Using the Web-Based Advanced User Interface

1 2 3 4 5
section

Setting MAC Address Control

The MAC address filter is a powerful security feature that allows you to specify which computers are allowed on the wireless network. Note: This list applies only to wireless computers. This list can be configured so any computer attempting to access the wireless network that is not specified in the filter list will be denied access. When you enable this feature, you must enter the MAC address of each client (computer) to which you want to allow network access. The Block feature lets you turn on and off access to the network easily for any computer without having to add and remove the computers MAC address from the list. (1)

6
(2) (3) (4)

7 8 9 10

Setting up an Allow Access List 1. Select the Allow radio button (1) to begin setting up a list of
computers allowed to connect to the wireless network.

2. Next, in the MAC Address field that is blank (2), type in the MAC
address of the wireless computer you want to be able to access the wireless network, then click <<Add (3).

3. Continue to do this until all of the computers you want to add have
been entered.

4. Click Apply Changes (4) to finish.

61

Using the Web-Based Advanced User Interface

Setting up a Deny Access List

The Deny Access list lets you specify computers that you DO NOT want to access the network. Any computer in the list will not be allowed access to the wireless network. All others will.

1. Select the Deny radio button (1) to begin setting up a list of computers
to be denied access to the wireless network.

2. Next, in the MAC Address field that is blank (2), type in the MAC
address of the wireless computer you want to deny access to the wireless network, then click <<Add (3).

3. Continue to do this until all of the computers you want to deny access to
have been entered.

4. Click Apply Changes (4) to finish.

(1)

(2) (3) (4)

62

Using the Web-Based Advanced User Interface

1 2 3 4 5
section

Configuring the Firewall

Your Router is equipped with a firewall that will protect your network from a wide array of common hacker attacks including: IP Spoofing Land Attack Ping of Death (PoD) Denial of Service (DoS) IP with zero length Smurf Attack TCP Null Scan SYN flood UDP flooding Tear Drop Attack ICMP defect RIP defect Fragment flooding

6 7 8 9 10

The firewall also masks common ports that are frequently used to attack networks. These ports appear to be stealth meaning that for all intents and purposes, they do not exist to a would-be hacker. You can turn the firewall function off if needed; however, it is recommended that you leave the firewall enabled. Disabling the firewall protection will not leave your network completely vulnerable to hacker attacks, but it is recommended that you leave the firewall enabled.

63

Using the Web-Based Advanced User Interface

Configuring Internal Forwarding Settings

The Virtual Servers function will allow you to route external (Internet) calls for services such as a web server (port 80), FTP server (Port 21), or other applications through your Router to your internal network. Since your internal computers are protected by a firewall, computers outside your network (over the Internet) cannot get to them because they cannot be seen. A list of common applications has been provided in case you need to configure the Virtual Server function for a specific application. If your application is not listed, you will need to contact the application vendor to find out which port settings you need.

Choosing an Application
Select your application from the drop-down list. Click Add. The settings will be transferred to the next available space in the screen. Click Apply Changes to save the setting for that application. To remove an application, select the number of the row that you want to remove then click Clear.

Manually Entering Settings into the Virtual Server

To manually enter settings, enter the IP address in the space provided for the internal (server) machine, the port(s) required to pass (use a comma between multiple ports), select the port type (TCP or UDP), and click Apply Changes. You can only pass one port per internal IP address. Opening ports in your firewall can pose a security risk. You can enable and disable settings very quickly. It is recommended that you disable the settings when you are not using a specific application.

64

Using the Web-Based Advanced User Interface

1 2 3 4 5
section

Setting Client IP Filters

The Router can be configured to restrict access to the Internet, email, or other network services at specific days and times. Restriction can be set for a single computer, a range of computers, or multiple computers.

6 7 8
To restrict Internet access to a single computer for example, enter the IP address of the computer you wish to restrict access to in the IP fields (1). Next, enter 80 in both the port fields (2). Select Both (3). Select Block (4). You can also select Always to block access all of the time. Select the day to start on top (5), the time to start on top (6), the day to end on the bottom (7), and the time to stop (8) on the bottom. Select Enable (9). Click Apply Changes. The computer at the IP address you specified will now be blocked from Internet access at the times you specified. Note: Be sure you have selected the correct time zone under Utilities> System Settings> Time Zone. (1) (2) (5) (6) (9)

9 10

(3)

(4)

(7)

(8)

65

Using the Web-Based Advanced User Interface

Enabling the Demilitarized Zone (DMZ)

The DMZ feature allows you to specify one computer on your network to be placed outside of the firewall. This may be necessary if the firewall is causing problems with an application such as a game or video conferencing application. Use this feature on a temporary basis. The computer in the DMZ is NOT protected from hacker attacks.

To put a computer in the DMZ, enter the last digits of its IP address in the IP field and select Enable. Click Apply Changes for the change to take effect. If you are using multiple static WAN IP addresses, it is possible to select which WAN IP address the DMZ host will be directed to. Type in the WAN IP address you wish the DMZ host to direct to, enter the last two digits of the IP address of the DMZ host computer, select Enable and click Apply Changes.

66

Using the Web-Based Advanced User Interface

1 2 3 4 5
section

Using Dynamic DNS

The Dynamic DNS service allows you to alias a dynamic IP address to a static host name in any of the many domains DynDNS.org offers, allowing your network computers to be more easily accessed from various locations on the Internet. DynDNS.org provides this service, for up to five host names, free to the Internet community. The Dynamic DNSSM service is ideal for a home website, file server, or to make it easy to access your home PC and stored files while youre at work. Using the service can ensure that your host name always points to your IP address, no matter how often your ISP changes it. When your IP address changes, your friends and associates can always locate you by visiting yourname.dyndns.org instead. To register free for your Dynamic DNS host name, please visit http://www.dyndns.org.

6 7 8 9 10

67

Using the Web-Based Advanced User Interface

Setting up the Routers Dynamic DNS Update Client

You must register with DynDNS.orgs free update service before using this feature. Once you have your registration, follow the directions below.

1. Enter your DynDNS.org user name in the User Name field (1). 2. Enter your DynDNS.org password in the Password field (2). 3. Enter the DynDNS.org domain name you set up with DynDNS.org in the
Domain Name field (3).

4. Click Update Dynamic DNS to update your IP address.

Whenever your IP address assigned by your ISP changes, the Router will automatically update DynDNS.orgs servers with your new IP address. You can also do this manually by clicking the Update Dynamic DNS button (4).

(1) (2) (3) (4)

68

Using the Web-Based Advanced User Interface

1 2 3 4
(1)

Blocking an ICMP Ping

Computer hackers use what is known as pinging to find potential victims on the Internet. By pinging a specific IP address and receiving a response from the IP address, a hacker can determine that something of interest might be there. The Router can be set up so it will not respond to an ICMP ping from the outside. This heightens your Routers security level.

5
section

6 7 8 9
To turn off the ping response, select Block ICMP Ping (1) and click Apply Changes. The Router will not respond to an ICMP ping.

10

69

Using the Web-Based Advanced User Interface

Utilities
The Utilities screen lets you manage different parameters of the Router and perform certain administrative functions.

Restarting the Router

Sometimes it may be necessary to restart or reboot the Router if it begins working improperly. Restarting or rebooting the Router will NOT delete any of your configuration settings.

70

Using the Web-Based Advanced User Interface

1 2 3 4 5
section
3. The following message will appear. Restarting the Router can take up
to 60 seconds. It is important not to turn off the power to the Router during the restart. Click OK.

Restarting the Router to Restore Normal Operation 1. Click the Restart Router button. 2. The following message will appear. Click OK.

6 7 8 9 10

71

Using the Web-Based Advanced User Interface

4. A 60-second countdown will appear on the screen. When the countdown

reaches zero, the Router will be restarted. The Router home page should appear automatically. If not, type in the Routers address (default = 192.168.2.1) into the navigation bar of your browser.

72

Using the Web-Based Advanced User Interface

1 2 3 4 5
1. Click the Restore Defaults button. 2. The following message will appear. Click OK.

Restoring Factory Default Settings

Using this option will restore all of the settings in the Router to the factory (default) settings. It is recommended that you back up your settings before you restore all of the defaults.

section

6 7 8 9 10

3. The following message will appear. Restoring the defaults includes

restarting the Router. It can take up to 60 seconds. It is important not to turn the power to the Router off during the restart. Click OK.

73

Using the Web-Based Advanced User Interface

4. A 60-second countdown will appear on the screen. When the countdown

reaches zero, the Routers defaults will be restored. The Router home page should appear automatically. If it does not, type in the Routers address (default = 192.168.2.1) into the navigation bar of your browser.

Saving a Current Configuration

You can save your current configuration by using this feature. Saving your configuration will allow you to restore it later if your settings are lost or changed. It is recommended that you back up your current configuration before performing a firmware update.

74

Using the Web-Based Advanced User Interface

1 2 3 4 5
section

1. Click Save. A window called File Download will open.

Click Save.

6
2. A window will open that allows you to select the location where you
want to save the configuration file. Select a location. You can name the file anything you want, or use the default name Config. Be sure to name the file so you can locate it yourself later. When you have selected the location and name of the file, click Save.

7 8 9 10

75

Using the Web-Based Advanced User Interface

3. When the save is complete, you will see the window below.
Click Close.

The configuration is now saved.

76

Using the Web-Based Advanced User Interface

1 2 3 4 5
section

Restoring a Previous Configuration

This option will allow you to restore a previously saved configuration.

6 7
1. Click Browse. A window will open that allows you to select the
location of the configuration file. All configuration files end with a .bin. Locate the configuration file you want to restore and double-click on it.

8 9 10

77

Using the Web-Based Advanced User Interface

2. You will be asked if you want to continue. Click OK.

3. A reminder window will appear. It will take up to 60 seconds for the

configuration restoration to complete. Click OK.

4. A 60-second countdown will appear on the screen. When the countdown

reaches zero, the Routers configuration will be restored. The Routers home page should appear automatically. If not, type in the Routers address (default = 192.168.2.1) into the navigation bar of your browser.

78

Using the Web-Based Advanced User Interface

1 2 3 4 5
section
(1)

Updating the Firmware

From time to time, Belkin may release new versions of the Routers firmware. Firmware updates contain feature improvements and fixes to problems that may have existed. When Belkin releases new firmware, you can download the firmware from the Belkin update website and update your Routers firmware to the latest version.

6 7 8 9

Checking for a New Version of Firmware

The Check Firmware (1) button allows you to instantly check for a new version of firmware. When you click the button, a new browser window will appear informing you that either no new firmware is available or that there is a new version available. If a new version is available, you will have the option to download it.

10

79

Using the Web-Based Advanced User Interface

Downloading a New Version of Firmware

If you click the Check Firmware button and a new version of firmware is available, you will see a screen similar to the one below:

1. To download the new version of firmware, click Download. 2. A window will open that allows you to select the location where you want to
save the firmware file. Select a location. You can name the file anything you want, or use the default name. Be sure to locate the file in a place where you can locate it yourself later. When you have selected the location, click Save.

80

Using the Web-Based Advanced User Interface

1 2 3 4 5
section

3. When the save is complete, you will see the following window.
Click Close.

6 7 8
The download of the firmware is complete. To update the firmware, follow the next steps in Updating the Routers Firmware.

9 10

81

Using the Web-Based Advanced User Interface

Updating the Routers Firmware 1. In the Firmware Update page, click Browse. A window
will open that allows you to select the location of the firmware update file.

2. Browse to the firmware file you downloaded. Select the file by doubleclicking on the file name.

3. The Update Firmware box will now display the location and name of the
firmware file you just selected. Click Update.

82

Using the Web-Based Advanced User Interface

1 2 3 4
5. You will see one more message. This message tells you that the
Router may not respond for as long as one minute as the firmware is loaded into the Router and the Router is rebooted. Click OK.

4. You will be asked if you are sure you want to continue. Click OK.

5
section

6 7
6. A 60-second countdown will appear on the screen. When the
countdown reaches zero, the Router firmware update will be complete. The Router home page should appear automatically. If not, type in the Routers address (default = 192.168.2.1) into the navigation bar of your browser.

8 9 10

83

Using the Web-Based Advanced User Interface

Changing System Settings

The System Settings page is where you can enter a new administrator password, set the time zone, enable remote management, and turn on and off the NAT function of the Router.

Setting or Changing the Administrator Password

The Router ships with NO password entered. If you wish to add a password for greater security, you can set a password here. Write down your password and keep it in a safe place, as you will need it if you need to log into the Router in the future. It is also recommended that you set a password if you plan to use the remote management feature of your Router.

84

Using the Web-Based Advanced User Interface

1 2 3 4 5
section

Changing the Login Time-Out Setting

The login time-out option allows you to set the period of time that you can be logged into the Routers advanced setup interface. The timer starts when there has been no activity. For example, imagine you have made some changes in the advanced setup interface, then left your computer alone without clicking Logout. Assuming the time-out is set to 10 minutes, 10 minutes after you leave, the login session will expire. You will have to log into the Router again to make any more changes. The login time-out option is for security purposes and the default is set to 10 minutes. Note: Only one computer can be logged into the Routers advanced setup interface at one time.

Setting the Time and Time Zone

The Router keeps time by connecting to a Simple Network Time Protocol (SNTP) server. This allows the Router to synchronize the system clock to the global Internet. The synchronized clock in the Router is used to record the security log and control client filtering. Select the time zone that you reside in. You have the option to select a primary and a backup NTP server to keep your Routers clock synchronized. Select your desired NPT server from the dropdown box, or simply keep it as is. If you reside in an area that observes daylight saving, then place a check mark in the box next to Enable Daylight Saving. The system clock may not update immediately. Allow at least 15 minutes for the Router to contact the time servers on the Internet and get a response. You cannot set the clock yourself.

6 7 8 9 10

85

Using the Web-Based Advanced User Interface

Enabling Remote Management

Before you enable this advanced feature of your Belkin Router, MAKE SURE YOU HAVE SET THE ADMINISTRATOR PASSWORD. Remote management allows you to make changes to your Routers settings from anywhere on the Internet. There are two methods of remotely managing the Router. The first is to allow access to the Router from anywhere on the Internet by selecting Any IP address can remotely manage the Router. By typing in your WAN IP address from any computer on the Internet, you will be presented with a login screen where you need to type in the password of your Router. The second method is to allow a specific IP address only to remotely manage the Router. This is more secure, but less convenient. To use this method, enter the IP address you know you will be accessing the Router from in the space provided and select Only this IP address can remotely manage the Router. Before you enable this function, it is STRONGLY RECOMMENDED that you set your administrator password. Leaving the password empty will potentially open your Router to intrusion. Advanced Feature: The Remote Access Port option allows you to configure the desired Remote Access Port for Remote Management feature. The default access port is set to port 8080.

86

Using the Web-Based Advanced User Interface

1 2 3 4 5
section

Enabling/Disabling UPnP
UPnP (Universal Plug-and-Play) is yet another advanced feature offered by your Belkin Router. It is a technology that offers seamless operation of voice messaging, video messaging, games, and other applications that are UPnPcompliant. Some applications require the Routers firewall to be configured in a specific way to operate properly. This usually requires opening TCP and UDP ports, and in some instances, setting trigger ports. An application that is UPnP-compliant has the ability to communicate with the Router, basically telling the Router which way it needs the firewall configured. The Router ships with the UPnP feature disabled. If you are using any applications that are UPnP-compliant, and wish to take advantage of the UPnP features, you can enable the UPnP feature. Simply select Enable in the UPnP Enabling section of the Utilities page. Click Apply Changes to save the change.

6 7 8

Enabling/Disabling Auto Firmware Update

This innovation provides the Router with the built-in capability to automatically check for a new version of firmware and alert you that the new firmware is available. When you log into the Routers advanced interface, the Router will perform a check to see if new firmware is available. If so, you will be notified. You can choose to download the new version or ignore it.

9 10

87

Manually Configuring Network Settings

Set up the computer that is connected to the cable or DSL modem FIRST using these steps. You can also use these steps to add computers to your Router after the Router has been set up to connect to the Internet.

Manually Configuring Network Settings in Mac OS up to 9.x 1. Pull down the Apple menu. Select Control Panels and
select TCP/IP.

2. You will see the TCP/IP control panel. Select Ethernet Built-In or
Ethernet in the Connect via: drop-down menu (1). (1) (2)

3. Next to Configure (2), if Manually is selected, your Router will need to be

set up for a static IP connection type. Write the address information in the table below. You will need to enter this information into the Router.

88

Manually Configuring Network Settings

1 2 3
5. Close the window. If you made any changes, the following window
will appear. Click Save.

4. If not already set, at Configure:, choose Using DHCP Server. This

will tell the computer to obtain an IP address from the Router.

4 5 6
section

7
Restart the computer. When the computer restarts, your network settings are now configured for use with the Router.

8 9 10

89

Manually Configuring Network Settings

Manually Configuring Network Settings in Mac OS X 1. Click on the System Preferences icon.

2. Select Network (1) from the System Preferences menu.

(1)

3. Select Built-in Ethernet (2) next to Show in the Network menu.

(2) (3) (5) (4)

90

Manually Configuring Network Settings

1 2 3 4 5 6
section

4. Select the TCP/IP tab (3). Next to Configure (4), you should see

Manually or Using DHCP. If you do not, check the PPPoE tab (5) to make sure that Connect using PPPoE is NOT selected. If it is, you will need to configure your Router for a PPPoE connection type using your user name and password. static IP connection type. Write the address information in the table below. You will need to enter this information into the Router.

5. If Manually is selected, your Router will need to be set up for a

7
6. If not already selected, select Using DHCP next to Configure (4),
then click Apply Now.

8 9 10

Your network settings are now configured for use with the Router.

91

Manually Configuring Network Settings

Manually Configuring Network Settings in Windows 2000 or XP 1. Click Start, Settings, then Control Panel. 2. Double-click on the Network and dial-up connections icon (Windows
2000) or the Network icon (Windows XP).

3. Right-click on the Local Area Connection associated with your network

adapter and select Properties from the drop-down menu.

4. In the Local Area Connection Properties window, click Internet

Protocol (TCP/IP) and click the Properties button. The following screen will appear:

(1) (2)

(3)

92

Manually Configuring Network Settings

1 2 3 4 5 6
section

5. If Use the following IP address (2) is selected, your Router will

need to be set up for a static IP connection type. Write the address information the table below. You will need to enter this information into the Router.

7
6. If not already selected, select Obtain an IP address automatically
(1) and Obtain DNS server address automatically (3). Click OK.

8 9 10

Your network settings are now configured for use with the Router.

93

Manually Configuring Network Settings

Manually Configuring Network Settings in Windows 98 or Me 1. Right-click on My Network Neighborhood and select Properties from the
drop-down menu.

2. Select TCP/IP -> settings for your installed network adapter. You will see
the following window. (2)

(1)

(3)

3. If Specify and IP address is selected, your Router will need to be set up

for a static IP connection type. Write the address information in the table below. You will need to enter this information into the Router.

4. Write the IP address and subnet mask from the IP Address tab (3). 5. Click the Gateway tab (2). Write the gateway address down in the chart.

94

Manually Configuring Network Settings

1 2 3 4 5 6
section
7. If not already selected, select Obtain IP address automatically on
the IP address tab. Click OK.

6. Click the DNS Configuration tab (1). Write the DNS address(es) in
the chart.

7 8 9 10

Restart the computer. When the computer restarts, your network settings are now configured for use with the Router.

95

Recommended Web Browser Settings

In most cases, you will not need to make any changes to your web browsers settings. If you are having trouble accessing the Internet or the Web-Based Advanced User Interface, then change your browsers settings to the recommended settings in this section.

Microsoft Internet Explorer 4.0 or Higher 1. Start your web browser. Select Tools then Internet Options.

96

Recommended Web Browser Settings

1 2 3 4 5 6 7
section

2. In the Internet Options screen, there are three selections: Never

dial a connection, Dial whenever a network connection is not present, and Always dial my default connection. If you can make a selection, select Never dial a connection. If you cannot make a selection, go to the next step.

8 9 10

3. Under the Internet Options screen, click on Connections and

select LAN Settings....

97

Recommended Web Browser Settings

4. Make sure there are no check marks next to any of the displayed options:
Automatically detect settings, Use automatic configuration script, and Use a proxy server. Click OK. Then click OK again in the Internet Options page.

98

Recommended Web Browser Settings

1 2 3 4 5 6 7
section

Netscape Navigator 4.0 or Higher 1. Start Netscape. Click on Edit then Preferences. 2. In the Preferences window, click on Advanced then select
Proxies. In the Proxies window, select Direct connection to the Internet.

8 9 10

99

Troubleshooting

Problem:
Installation CD does not automatically start.

Solution:
If the CD-ROM does not start the Setup Assistant automatically, it could be that the computer is running other applications that are interfering with the CD drive. 1. If the Setup Assistant screen does not appear within 15-20 seconds, open up your CD-ROM drive by double-clicking on the My Computer icon that is located on your desktop.

2. Next, double-click on the CD-ROM drive that the Setup Assistant CD has been placed in to start the installation.

3. The Setup Assistant should start within a few seconds. If, instead, a window appears showing the files on the CD, double-click on the icon labeled EasyInstall.exe.

4. If the Setup Assistant still does not start, reference the section titled Manually Configuring Network Settings (page 88 of this User Manual) for an alternative setup method).

100

Troubleshooting
1 2 3 4 5 6 7 8
section

Problem:
Setup Assistant cannot find my Router.

Solution:
If the Setup Assistant is not able to find the Router during the installation process, please check the following items: 1. If the Setup Assistant is not able to find the Router during the installation process, there may be third-party firewall software installed on the computer attempting to access the Internet. Examples of third-party firewall software are ZoneAlarm, BlackICE PC Protection, McAfee Personal Firewall, and Norton Personal Firewall. If you do have firewall software installed on your computer, please make sure that you properly configure it. You can determine if the firewall software is preventing Internet access by temporarily turning it off. If, while the firewall is disabled, Internet access works properly, you will need to change the firewall settings to function properly when it is turned on. Please refer to the instructions provided by the publisher of your firewall software for instructions on configuring the firewall to allow Internet access. 2. Unplug power to the Router for 10 seconds, and then plug the power back into the Router. Ensure that the Routers Power light is on; it should be solid green. If not, check to make sure that the AC adapter is connected to the Router and plugged into a wall outlet. 3. Ensure that you have a cable (use the cable included with the Router) connected between (1) the network (Ethernet) port on the back of the computer and (2) one of the LAN ports, labeled 1 through 4, on the back of the Router. Note: The computer should NOT be connected to the port labeled Internet/ WAN on the back of the Router. 4. Try shutting down and restarting your computer, then rerunning the Setup Assistant. If the Setup Assistant is still unable to find the Router, reference the section titled Manually Configuring Network Settings for installation steps.

9 10

Problem:
Setup Assistant cannot connect my Router to the Internet.

Solution:
If the Setup Assistant is not able to connect the Router to the Internet, please check the following items: 1. Use the troubleshooting suggestions within the Setup Assistant. If the

101

Troubleshooting

troubleshooting screen does not open automatically, click on the Troubleshoot button in the lower, right-hand corner of the Setup Assistant window. 2. If your ISP requires a user name and password, make sure that you have typed in your user name and password correctly. Some user names require that the ISPs domain may be at the end of the name. Example: [email protected]. The @myisp.com part of the user name may need to be typed as well as your user name. If you continue to have no Internet connection, reference the section titled Manually Configuring Network Settings (page 88 of this User Manual) for an alternative setup method.

Problem:
The Setup Assistant completed installation, but my web browser doesnt work. I am unable to connect to the Internet. The WAN light on my Router is off, and the Connected light is blinking.

Solution:
If you cannot connect to the Internet, and the WAN light is off, and the Connected light is blinking, the problem may be that your modem and Router are not connected properly. 1. Make sure the network cable between the modem and the Router is connected. We strongly recommend using the cable that was supplied with your cable or DSL modem for this purpose. The cable should be connected at one end to the Routers Internet/WAN port, and at the other end to the network port on your modem. 2. Unplug the cable or DSL modem from its power source for three minutes. After three minutes, plug the modem back into its power source. This may force the modem to properly recognize the Router. 3. Unplug the power to your Router, wait 10 seconds, and then reconnect the power. This will cause the Router to reattempt communication with the modem. If the WAN light on the Router is not lit after completing these steps, please contact Belkin Technical Support. 4. Try shutting down and restarting your computer.

Problem:
The Setup Assistant completed installation, but my web browser doesnt work. I am unable to connect to the Internet. The WAN light on my Router is on, and the Connected light is blinking.

102

Troubleshooting
1 2 3 4 5 6 7 8
section

Solution:
1. If you cannot connect to the Internet, the WAN light is on, and the Connected light is blinking, the problem may be that your connection type may not match the ISPs connection. 2. If you have a static IP address connection, your ISP must assign you the IP address, subnet mask, and gateway address. Please refer to the section entitled Alternate Setup Method for details on changing this setting. 3. If you have a PPPoE connection, your ISP will assign you a user name and password and sometimes a service name. Make sure the Routers connection type is configured to PPPoE and the settings are entered properly. Please refer to the section entitled Alternate Setup Method for details on changing this setting. 4. You may need to configure your Router to meet the specific requirements of your ISP. To search our knowledge base for ISP-specific issues, go to: http://web.belkin.com/support and type in ISP. If you are still unable to access the Internet after verifying these settings, please contact Belkin Technical Support.

Problem:
The Setup Assistant completed, but my web browser doesnt work. I am unable to connect to the Internet. The WAN light on my Router is blinking, and the Connected light is solid.

9 10

Solution:
1. If the WAN light is blinking, and the Connected light is solid, but you are unable to access the Internet, there may be third-party firewall software installed on the computer attempting to access the Internet. Examples of third-party firewall software are ZoneAlarm, BlackICE PC Protection, McAfee Personal Firewall, and Norton Personal Firewall. 2. If you do have firewall software installed on your computer, please make sure that you properly configure it. You can determine if the firewall software is preventing Internet access by temporarily turning it off. If, while the firewall is disabled, Internet access works properly, you will need to change the firewall settings to function properly when it is turned on. 3. Please refer to the instructions provided by the publisher of your firewall software for instructions on configuring the firewall to allow Internet access. If you are still unable to access the Internet after disabling any firewall software, please contact Belkin Technical Support.

103

Troubleshooting

Problem:
I cant connect to the Internet wirelessly.

Solution:
If you are unable to connect to the Internet from a wireless computer, please check the following items: 1. Look at the lights on your Router. If youre using a Belkin Router, the lights should be as follows: The Power light should be on. The Connected light should be on, and not blinking. The WAN Internet light should be either on or blinking. The Wireless light should be on or blinking 2. Open your wireless utility software by clicking on the icon in the system tray at the bottom, right-hand corner of the screen.

3. The exact window that opens will vary depending on the model of wireless card you have; however, any of the utilities should have a list of Available Networksthose wireless networks it can connect to. Does the name of your wireless network appear in the results? Yes, my network name is listed go to the troubleshooting solution titled I cant connect to the Internet wirelessly, but my network name is listed. No, my network name is not listed go to the troubleshooting solution titled I cant connect to the Internet wirelessly, and my network name is not listed.

104

Troubleshooting
1 2 3 4 5 6 7 8
section

Problem:
I cant connect to the Internet wirelessly, but my network name is listed.

Solution:
If the name of your network is listed in the Available Networks list, please follow the steps below to connect wirelessly: 1. Click on the correct network name in the Available Networks list. 2. If the network has security (encryption) enabled, you will need to enter the network key. For more information regarding security, see the section entitled Setting WEP Encryption (page 58). 3. Within a few seconds, the tray icon in the lower, left-hand corner of your screen should turn green, indication of a successful connection to the network.

Problem:
I cant connect to the Internet wirelessly, and my network name is not listed.

Solution:
If the correct network name is not listed under Available Networks in the wireless utility, please attempt the following troubleshooting steps: 1. Temporarily move computer, if possible, five to 10 feet from the Router. Close the wireless utility, and reopen it. If the correct network name now appears under Available Networks, you may have a range or interference problem. Please see the suggestions discussed in the section titled Placement of your Wireless G Plus MIMO Router of this User Manual. 2. Using a computer that is connected to the Router via a network cable (as opposed to wirelessly), ensure that Broadcast SSID is enabled. This setting is found on the Routers wireless Channel and SSID configuration page. If you are still unable to access the Internet after completing these steps, please contact Belkin Technical Support.

9 10

105

Troubleshooting

Problem:
My wireless network performance is inconsistent. Data transfer is sometimes slow. Signal strength is poor. Difficulty establishing and/or maintaining a Virtual Private Network (VPN) connection.

Solution:
Wireless technology is radio-based, which means connectivity and the throughput performance between devices decreases when the distance between devices increases. Other factors that will cause signal degradation (metal is generally the worst culprit) are obstructions such as walls and metal appliances. Note also that connection speed may decrease as you move farther away from the Router (or access point). In order to determine if wireless issues are related to range, we suggest temporarily moving the computer, if possible, five to 10 feet from the Router. Changing the wireless channelDepending on local wireless traffic and interference, switching the wireless channel of your network can improve performance and reliability. The default channel the Router is shipped with is channel 11; you may choose from several other channels depending on your region. See the section on page 52 entitled Changing the Wireless Channel for instructions on how to choose other channels. Limiting the wireless transmit rateLimiting the wireless transmit rate can help improve the maximum wireless range and connection stability. Most wireless cards have the ability to limit the transmission rate. To change this property, go to the Windows Control Panel, open Network Connections and double-click on your wireless cards connection. In the properties dialog, select the Configure button on the General tab (Windows 98 users will have to select the wireless card in the list box and then click Properties), then choose the Advanced tab and select the rate property. Wireless client cards are usually set to automatically adjust the wireless transmit rate for you, but doing so can cause periodic disconnects when the wireless signal is too weak; as a rule, slower transmission rates are more stable. Experiment with different connection rates until you find the best one for your environment. Note that all available transmission rates should be acceptable for browsing the Internet. For more assistance, see your wireless cards user manual.

106

Troubleshooting
1 2 3 4 5 6 7 8
section

Problem:
I am having difficulty setting up Wired Equivalent Privacy (WEP) security on a Belkin Router (or Belkin Access Point).

Solution:
1. Log into your Wireless Router or (Access Point). Open your web browser and type in the IP address of the Wireless Router (or Access Point). (The Routers default is 192.168.2.1, the 802.11g Access Point is 192.168.2.254.) Log into your Router by clicking on the Login button in the top right-hand corner of the screen. You will be asked to enter your password. If you never set a password, leave the Password field blank and click Submit. Click the Wireless tab on the left of your screen. Select the Encryption or Security tab to get to the security settings page. 2. Select 128-bit WEP from the drop-down menu. 3. After selecting your WEP encryption mode, you can type in your hex WEP key manually, or you can type in a passphrase in the Passphrase field and click Generate to create a WEP key from the passphrase. Click Apply Changes to finish. You must now set all of your clients to match these settings. A hex (hexadecimal) key is a mixture of numbers and letters from A-F and 0-9. For 128-bit WEP, you need to enter 26 hex keys. For example: C3 03 0F AF 4B B2 C3 D4 4B C3 D4 E7 E4 = 128-bit key 4. Click Apply Changes to finish. Encryption in the Wireless Router is now set. Each of your computers on your wireless network will now need to be configured with the same security settings. WARNING: If you are configuring the Wireless Router (or Access Point) from a computer with a wireless client, you will need to ensure that security is turned on for this wireless client. If this is not done, you will lose your wireless connection. Note to Mac Users: Original Apple AirPort products support 64-bit encryption only. Apple AirPort 2 products can support 64-bit or 128bit encryption. Please check your Apple AirPort product to see which version you are using. If you cannot configure your network with 128-bit encryption, try 64-bit encryption.

9 10

107

Troubleshooting

Problem:
I am having difficulty setting up Wired Equivalent Privacy (WEP) security on a Belkin client card.

Solution:
The client card must use the same key as the Wireless Router (or access point). For instance, if your Wireless Router (or access point) uses the key 0011223344556677 8899AABBCC, then the client card must be set to the exact same key. 1. Double-click the Signal Indicator icon to bring up the Wireless Network screen. 2. The Advanced button will allow you to view and configure more options of your card. 3. Once the Advanced button is clicked, the Belkin Wireless LAN Utility will appear. This Utility will allow you to manage all the advanced features of the Belkin Wireless Card. 4. Under the Wireless Network Properties tab, select a network name from the Available Networks list and click the Properties button. 5. Under Data Encryption, select WEP. 6. Ensure that the check box The key is provided for me automatically at the bottom is unchecked. If you are using this computer to connect to a corporate network, please consult your network administrator if this box needs to be checked. 7. Type your WEP key in the Network key box. Important: A WEP key is a mixture of numbers and letters from A-F and 0-9. For 128-bit WEP, you need to enter 26 keys. This network key needs to match the key you assign to your Wireless Router (or access point). For example: C3 03 0F AF 4B B2 C3 D4 4B C3 D4 E7 E4 = 128-bit key 8. Click OK, and then Apply to save the settings. If you are not using a Belkin wireless client card, please consult the manufacturers user manual for that wireless client card.

108

Troubleshooting
1 2 3 4 5 6 7 8
section

Problem:
Do Belkin products support WPA?

Solution:
You need to download the latest driver for your Belkin 802.11g Wireless Desktop or Notebook Network Card from the Belkin support site. Other operating systems are not supported at this time. Microsofts patch only supports devices with WPA-enabled drivers such as Belkin 802.11g products. Download the latest driver at http://web.belkin.com/support for the following products: F5D7000, F5D7001, F5D7010, F5D7230-4, F5D7231-4, F5D7130, F5D9010, F5D9050, F5D9230-4

Problem:
I am having difficulty setting up Wireless Protected Access (WPA) security on a Belkin Wireless Router (or Belkin Access Point) for a home network.

Solution:
1. From the Security Mode drop-down menu, select WPA-PSK (no server). 2. For Encryption Technique, select TKIP or AES. This setting will have to be identical on the clients that you set up. 3. Enter your pre-shared key. This can be from eight to 63 characters and can be letters, numbers, symbols, or spaces. This same key must be used on all of the clients that you set up. For example, your PSK might be something like: Smith family network key. 4. Click Apply Changes to finish. You must now set all clients to match these settings.

9 10

Problem:
I am having difficulty setting up Wireless Protected Access (WPA) security on a Belkin wireless client card for a home network.

Solution:
Clients must use the same key that the Wireless Router (or access point) uses. For instance, if the key is Smith Family Network Key in the Wireless Router (or access point), the clients must also use that same key. 1. Double-click the Signal Indicator icon to bring up the Wireless Network screen. The Advanced button will allow you to view and configure more options of your card.

109

Troubleshooting

2. Once the Advanced button is clicked, the Belkin Wireless Utility will appear. This Utility will allow you to manage all the advanced features of the Belkin Wireless Card. 3. Under the Wireless Network Properties tab, select a network name from the Available Networks list and click the Properties button. 4. Under Network Authentication, select WPA-PSK (no server). 5. Type your WPA key in the Network key box. Important: WPA-PSK is a mixture of numbers and letters from A-Z and 0-9. For WPA-PSK you can enter eight to 63 characters. This network key needs to match the key you assign to your Wireless Router (or access point). 6. Click OK, then Apply to save the settings.

Problem:
I am NOT using a Belkin client card for a home network and I am having difficulty setting up Wireless Protected Access (WPA) security.

Solution:
If you are not using a Belkin Wireless Desktop or Wireless Notebook Network Card that is not equipped with WPA-enabled software, a file from Microsoft called Windows XP Support Patch for Wireless Protected Access is available for free download. Download the patch from Microsoft by searching the knowledge base for Windows XP WPA. Note: The file that Microsoft has made available works only with Windows XP. Other operating systems are not supported at this time. You also need to ensure that the wireless cards manufacturer supports WPA and that you have downloaded and installed the latest driver from their support site. Supported Operating Systems: Windows XP Professional Windows XP Home Edition 1. Under Windows XP, click Start > Control Panel > Network Connections. 2. Right-click on the Wireless Networks tab. Ensure the Use Windows to configure my wireless network settings check box is checked. 3. Under the Wireless Networks tab, click the Configure button. 4. For a home or small business user, select WPA-PSK under Network Administration. Note: Select WPA (with radius server) if you are using this computer to connect to a corporate network that supports an authentication server such as a radius server. Please consult your network administrator for further information. 5. Select TKIP or AES under Date Encryption. This setting will have to be identical to the Wireless Router (or access point) that you set up.

110

Troubleshooting
1 2 3 4 5 6 7 8
G Plus (802.11g with HSM) 10x faster than 802.11b* Common household devices such as cordless phones and microwave ovens may interfere with the unlicensed band 2.4GHz Compatible with 802.11b/g Up to 700 ft.* G Plus MIMO (802.11g with MIMO MRC) 10x faster than 802.11b* Common household devices such as cordless phones and microwave ovens may interfere with the unlicensed band 2.4GHz Compatible with 802.11b/g Up to 1,000 ft.* N1 MIMO (draft 802.11n with MIMO) Wired speed over the air* Common household devices such as cordless phones and microwave ovens may interfere with the unlicensed band 2.4GHz Compatible with draft 802.11n** and 802.11b/g Up to 1,400 ft.*

6. Type in your encryption key in the Network key box. Important: Enter your pre-shared key. This can be from eight to 63 characters and can be letters, numbers, or symbols. This same key must be used on all of the clients that you set up. 7. Click OK to apply settings.

Problem:
What is the difference between 802.11b, 802.11g, G Plus MIMO, and Pre-N?

Solution:
Currently there are four levels of wireless networking standards, which transmit data at very different maximum speeds. Each is based on the designation 802.11(x), so named by the IEEE, the board that is responsible for certifying networking standards. The most common wireless networking standard, 802.11b, transmits information at 11Mbps; 802.11a and 802.11g work at 54Mbps; G Plus MIMO works at 54Mbps; and Pre-N works at 108Mbps. Wireless Comparison Chart
Wireless Technology Speed* 802.11b 11Mbps link rate/baseline Common household devices such as cordless phones and microwave ovens may interfere with the unlicensed band 2.4GHz Compatible with 802.11g Typically 100200 ft.* indoors G (802.11g) 5x faster than 802.11b* Common household devices such as cordless phones and microwave ovens may interfere with the unlicensed band 2.4GHz Compatible with 802.11b/g Up to 400 ft.*

section

9 10

Frequency

Compatibility

Coverage*

Advantage

Common Enhanced Maturelegacy widespread speed and technology use for coverage Internet sharing

Better coverage Leading edge and consistent best coverage speed and range and throughput

*Distance and connection speeds will vary depending on your networking environment. **This Router is compatible with products based on the same version of the draft 802.11n specifications and may require a software upgrade for best results.

111

Troubleshooting

Technical Support
You can find technical support information at http://www.belkin.com/networking or www.belkin.com through the tech support area. If you want to contact technical support by phone, please call:

US: 877-736-5771 800-223-5546 ext. 2263 310-898-1100 ext. 2263 UK: 0845 607 77 87 Australia: 1800 235 546 New Zealand: 0800 235 546 Singapore: 65 64857620 Europe: www.belkin.com/support

112

Information
1 2 3 4 5 6 7 8 9
section

FCC Statement
DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY
We, Belkin International, Inc., of 501 West Walnut Street, Compton, CA 90220, declare under our sole responsibility that the product,

F5D9230-4
to which this declaration relates, complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution: Exposure to Radio Frequency Radiation.

of this device is far below the FCC radio frequency exposure limits. Nevertheless, the device shall be used in such manner that the potential for human contact during normal operation is minimized. When connecting an external antenna to the device, the antenna shall be placed in such a manner to minimize the potential for human contact during normal operation. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.

Federal Communications Commission Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the distance between the equipment and the receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

10

Modifications
The FCC requires the user to be notified that any changes or modifications to this device that are not expressly approved by Belkin International, Inc. may void the users authority to operate the equipment.

Canada-Industry Canada (IC)

The wireless radio of this device complies with RSS 139 & RSS 210 Industry Canada. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B conforme la norme NMB-003 du Canada.

113

Information

Europe-European Union Notice

Radio products with the CE 0682 or CE alert marking comply with the R&TTE Directive (1995/5/ EC) issued by the Commission of the European Community. Compliance with this directive implies conformity to the following European Norms (in brackets are the equivalent international standards). EN 60950 (IEC60950) Product Safety EN 300 328 Technical requirement for radio equipment ETS 300 826 General EMC requirements for radio equipment. To determine the type of transmitter, check the identification label on your Belkin product. Products with the CE marking comply with the EMC Directive (89/336/EEC) and the Low Voltage Directive (72/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms (in brackets are the equivalent international standards). EN EN EN EN EN 55022 (CISPR 22) Electromagnetic Interference 55024 (IEC61000-4-2,3,4,5,6,8,11) Electromagnetic Immunity 61000-3-2 (IEC610000-3-2) Power Line Harmonics 61000-3-3 (IEC610000) Power Line Flicker 60950 (IEC60950) Product Safety

Products that contain the radio transmitter are labeled with CE 0682 or CE alert marking and may also carry the CE logo.

Belkin International, Inc., Limited Lifetime Product Warranty

What this warranty covers.
Belkin International, Inc. (Belkin) warrants to the original purchaser of this Belkin product that the product shall be free of defects in design, assembly, material, or workmanship.

What the period of coverage is.

Belkin warrants the Belkin product for the lifetime of the product.

What will we do to correct problems?

Product Warranty. Belkin will repair or replace, at its option, any defective product free of charge (except for shipping charges for the product). What is not covered by this warranty? All above warranties are null and void if the Belkin product is not provided to Belkin for inspection upon Belkins request at the sole expense of the purchaser, or if Belkin determines that the Belkin product has been improperly installed, altered in any way, or tampered with. The Belkin Product Warranty does not protect against acts of God such as flood, earthquake, lightning, war, vandalism, theft, normal-use wear and tear, erosion, depletion, obsolescence, abuse, damage due to low voltage disturbances (i.e. brownouts or sags), non-authorized program, or system equipment modification or alteration.

114

Information
1 2 3 4 5 6 7 8 9
section

How to get service.

To get service for your Belkin product you must take the following steps: 1. Contact Belkin International, Inc. at 501 W. Walnut St., Compton CA 90220, Attn: Customer Service, or call (800)-223-5546, within 15 days of the Occurrence. Be prepared to provide the following information: a. The part number of the Belkin product. b. Where you purchased the product. c. When you purchased the product. d. Copy of original receipt. 2. Your Belkin Customer Service Representative will then instruct you on how to forward your receipt and Belkin product and how to proceed with your claim. Belkin reserves the right to review the damaged Belkin product. All costs of shipping the Belkin product to Belkin for inspection shall be borne solely by the purchaser. If Belkin determines, in its sole discretion, that it is impractical to ship the damaged equipment to Belkin, Belkin may designate, in its sole discretion, an equipment repair facility to inspect and estimate the cost to repair such equipment. The cost, if any, of shipping the equipment to and from such repair facility and of such estimate shall be borne solely by the purchaser. Damaged equipment must remain available for inspection until the claim is finalized. Whenever claims are settled, Belkin reserves the right to be subrogated under any existing insurance policies the purchaser may have.

How state law relates to the warranty.

THIS WARRANTY CONTAINS THE SOLE WARRANTY OF BELKIN, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR, EXCEPT AS REQUIRED BY LAW, IMPLIED, INCLUDING THE IMPLIED WARRANTY OR CONDITION OF QUALITY, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND SUCH IMPLIED WARRANTIES, IF ANY, ARE LIMITED IN DURATION TO THE TERM OF THIS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. IN NO EVENT SHALL BELKIN BE LIABLE FOR INCIDENTAL, SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL OR MULTIPLE DAMAGES SUCH AS, BUT NOT LIMITED TO, LOST BUSINESS OR PROFITS ARISING OUT OF THE SALE OR USE OF ANY BELKIN PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. This warranty gives you specific legal rights, and you may also have other rights, which may vary from state to state. Some states do not allow the exclusion or limitation of incidental, consequential, or other damages, so the above limitations may not apply to you.

10

115

Wireless G Plus MIMO

Router

Belkin Tech Support US: 877-736-5771 800-223-5546 ext. 2263 310-898-1100 ext. 2263 UK: 0845 607 77 87 Australia: 1800 235 546 New Zealand: 0800 235 546 Singapore: 65 64857620 Europe: www.belkin.com/support Belkin International, Inc. 501 West Walnut Street Los Angeles, CA 90220-5221, USA 310-898-1100 310-898-1111 fax Belkin Ltd. Express Business Park, Shipton Way Rushden, NN10 6GL, United Kingdom +44 (0) 1933 35 2000 +44 (0) 1933 31 2000 fax

Belkin B.V. Boeing Avenue 333 1119 PH Schiphol-Rijk, The Netherlands +31 (0) 20 654 7300 +31 (0) 20 654 7349 fax Belkin Ltd. 4 Pioneer Avenue Tuggerah Business Park Tuggerah, NSW 2259, Australia +61 (0) 2 4350 4600 +61 (0) 2 4350 4700 fax

2008 Belkin International, Inc. All rights reserved. All trade names are registered trademarks of respective manufacturers listed. Mac, Mac OS, Apple, and AirPort are trademarks of Apple Inc., registered in the U.S. and other countries. Windows, Microsoft, and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. P74880-D