Scribd
Upload
105 views2 pages

Design A Micro-Strip Band Pass Filter For 6 GHZ

1) The document describes the design of a microstrip band pass filter for 6 GHz using IE3D simulator software. 2) A 3-pole Chebyshev filter with a passband ripple of 0.1 dB and centered at 6 GHz was designed on an FR4 substrate. 3) The filter was simulated using IE3D and test measurements found the cutoff frequency was accurately 6 GHz, meeting the design specifications.

Uploaded by

Editorijer Ijer
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
105 views2 pages

Design A Micro-Strip Band Pass Filter For 6 GHZ

1) The document describes the design of a microstrip band pass filter for 6 GHz using IE3D simulator software. 2) A 3-pole Chebyshev filter with a passband ripple of 0.1 dB and centered at 6 GHz was designed on an FR4 substrate. 3) The filter was simulated using IE3D and test measurements found the cutoff frequency was accurately 6 GHz, meeting the design specifications.

Uploaded by

Editorijer Ijer
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

International Journal of Engineering Research Volume No.1, Issue No.

2, pp : 36-37

(ISSN : 2319-6890) 01 Dec. 2012

Design a Micro-Strip Band Pass Filter for 6 GHz


Ashish Duvey Department of Electronics, SRCEM Banmore, Morena -476444 [email protected]
filter with normalize elements [2].

Abstract Purpose of this paper described about the design of microwave band pass filter by using microstrip layout. A microwave filter is two port network used to control the frequency response. The developments after micro-strip filter are simulated by using IE3D simulator software. Photolithographic process is used for fabrication and after fabrication final testing had done by using the spectrum analyzer. Keywords : Band pass filter (BPF) and IE3D software. Introduction The rapid growth in commercial microwave communication systems had been developed. Hense microstrip technology play important role in many RF or Microwave applications. Emerging application such as wireless communication continue to challenge RF/Microwave filters with ever requirement higher performance, smaller size, lighter weight and lowest cost[2]. Coupled microstrip line The coupled microstrip line are exhibiting are field term with Quasi-TEM.it has two propagation factor Even mode and odd mode.

Fig.3 Equivalent circuit for band pass filter 5. Obtain the even and odd mode coupled line characteristics impedance Z0e and Zo.

Where

Fig.2 Coupled Microstrip Line Designing Procedure:1. Determine the number of sections from the specified attenuation characteristic for microstrip parameters. 6. Determine microstrip width and separations (W&s) of the end-coupled half wavelength filter [3]. No of Order 3 Pass band Ripple 0.1dB Impedance(Z0)

Table 1:2. Determine the value of prototype element to realize the specifications Ex. Chebyshev filter prototype (go=1, c=6 and 0.1 dB ripple). 3. 4. go = g4 = 1.0, g1 = g3 = 1.0316, and g2 = 1.1474. Determine the one type resonator network and determine the inverter value for to equivalent realizations of the generic multi-sections low pass

Midband Freq. Range 6GHz

50 ohm

Fig4 General Configuration of end-coupled microstrip band pass filter

IJER@2012

Page 36

International Journal of Engineering Research Volume No.1, Issue No.2, pp : 36-37


7. Calculate the coupled section length which slightly less than quarter wavelength at center frequency to account for the end fringing. Simulation Result:-

(ISSN : 2319-6890) 01 Dec. 2012

Calculated parameter for design:1. Frequency bandwidth 0.028 or 2.8% 2. Number of poles, N=3 3. Mid band frequency f0= 6GHz. 4. Pass band ripple 0.01dB. 5. Element values are g0 = g4 = 1.0, g1 = g3 = 1.0316, and g2 = 1.1474 6. Dielectric constant r =10.8 7. Thickness of substrate h=1.27mm. 8. The line width for microstrip W = 1.1 mm. 9. Characteristic impedance Zo = 50 ohm. Then elements dimensions will be on FR4 microstrip PCB board as shown in fig.5

Fig.7 Result in IE3D Conclusions:After The Whole Analysis It Is Clearly Seen That The Proposed Microstrip Band Pass Filter Has Obtained Accurate Result For 6GHz Cutoff Frequency. References:[1] Pozar, David M. (1998). Microwave Engineering. 2nd Edition, USA: John Wiley &Sons, Inc. [2] Ludwig, Reinhold and Bretchko Pavel (2000), RF Circuit Design - Theory and Application. New Jersey, USA: Prentice -Hall, Inc. [3] Hong, Jia-Sheng and Lanchester, M.J. (2001). Microstrip Filters for RF / Microwave Applications. USA: John Wiley & Sons, Inc. [4] Zeland Software Inc., IE3D Manual, 2001.

Fig.5 Dimension geometry of band pass filter.

Geometry on simulator:Band pass Geometry Design On IE3D as Shown In Fig6.

Fig.6 Geometry

IJER@2012

Page 37

You might also like