C H A P T E R

15

Configuring STP
This chapter describes how to configure the Spanning Tree Protocol (STP) on your Catalyst 3550 switch. For information about the Rapid Spanning Tree Protocol (RSTP), the Multiple Spanning Tree Protocol (MSTP), and the per-VLAN rapid spanning tree (PVRST), see Chapter 16, Configuring RSTP and MSTP. For information about optional spanning-tree features, see Chapter 17, Configuring Optional Spanning-Tree Features.

Note

For complete syntax and usage information for the commands used in this chapter, refer to the command reference for this release. This chapter consists of these sections:

Understanding Spanning-Tree Features, page 15-1 Configuring Spanning-Tree Features, page 15-10 Displaying the Spanning-Tree Status, page 15-20

Understanding Spanning-Tree Features

These sections describe how spanning-tree features work:

STP Overview, page 15-2 Supported Spanning-Tree Instances, page 15-2 Bridge Protocol Data Units, page 15-2 Election of the Root Switch, page 15-3 Bridge ID, Switch Priority, and Extended System ID, page 15-4 Spanning-Tree Timers, page 15-4 Creating the Spanning-Tree Topology, page 15-5 Spanning-Tree Interface States, page 15-5 Spanning-Tree Address Management, page 15-8 STP and IEEE 802.1Q Trunks, page 15-8 VLAN-Bridge STP, page 15-8

Catalyst 3550 Multilayer Switch Software Configuration Guide 78-11194-07

15-1

Chapter 15 Understanding Spanning-Tree Features

Configuring STP

Spanning Tree and Redundant Connectivity, page 15-9 Accelerated Aging to Retain Connectivity, page 15-9

STP Overview
STP is a Layer 2 link management protocol that provides path redundancy while preventing loops in the network. For a Layer 2 Ethernet network to function properly, only one active path can exist between any two stations. Spanning-tree operation is transparent to end stations, which cannot detect whether they are connected to a single LAN segment or a switched LAN of multiple segments. When you create fault-tolerant internetworks, you must have a loop-free path between all nodes in a network. The spanning-tree algorithm calculates the best loop-free path throughout a switched Layer 2 network. Switches send and receive spanning-tree frames, called bridge protocol data units (BPDUs), at regular intervals. The switches do not forward these frames, but use the frames to construct a loop-free path. Multiple active paths among end stations cause loops in the network. If a loop exists in the network, end stations might receive duplicate messages. Switches might also learn end-station MAC addresses on multiple Layer 2 interfaces. These conditions result in an unstable network. Spanning tree defines a tree with a root switch and a loop-free path from the root to all switches in the Layer 2 network. Spanning tree forces redundant data paths into a standby (blocked) state. If a network segment in the spanning tree fails and a redundant path exists, the spanning-tree algorithm recalculates the spanning-tree topology and activates the standby path. When two interfaces on a switch are part of a loop, the spanning-tree port priority and path cost settings determine which interface is put in the forwarding state and which is put in the blocking state. The port priority value represents the location of an interface in the network topology and how well it is located to pass traffic. The path cost value represents media speed.

Supported Spanning-Tree Instances

The switch supports the per-VLAN spanning tree (PVST) and a maximum of 128 spanning-tree instances. The switch also supports the PVRST, which uses RSTP to provide rapid convergence of the PVST. For information about the PVRST, see the Spanning-Tree Instances Using RSTP section on page 16-2. For information about how spanning tree interoperates with the VLAN Trunking Protocol (VTP), see the STP Configuration Guidelines section on page 15-11.

Bridge Protocol Data Units

The stable, active spanning-tree topology of a switched network is determined by these elements:

The unique bridge ID (switch priority and MAC address) associated with each VLAN on each switch The spanning-tree path cost to the root switch The port identifier (port priority and MAC address) associated with each Layer 2 interface

When the switches in a network are powered up, each functions as the root switch. Each switch sends a configuration BPDU through all of its ports. The BPDUs communicate and compute the spanning-tree topology. Each configuration BPDU contains this information:

The unique bridge ID of the switch that the sending switch identifies as the root switch The spanning-tree path cost to the root

Catalyst 3550 Multilayer Switch Software Configuration Guide

15-2

78-11194-07

Chapter 15

Configuring STP Understanding Spanning-Tree Features

The bridge ID of the sending switch Message age The identifier of the sending interface Values for the hello, forward-delay, and max-age protocol timers

When a switch receives a configuration BPDU that contains superior information (lower bridge ID, lower path cost, and so forth), it stores the information for that port. If this BPDU is received on the root port of the switch, the switch also forwards it with an updated message to all attached LANs for which it is the designated switch. If a switch receives a configuration BPDU that contains inferior information to that currently stored for that port, it discards the BPDU. If the switch is a designated switch for the LAN from which the inferior BPDU was received, it sends that LAN a BPDU containing the up-to-date information stored for that port. In this way, inferior information is discarded, and superior information is propagated on the network. A BPDU exchange results in these actions:

One switch in the network is elected as the root switch. A root port is selected for each switch (except the root switch). This port provides the best path (lowest cost) when the switch forwards packets to the root switch. The shortest distance to the root switch is calculated for each switch based on the path cost. A designated switch for each LAN segment is selected. The designated switch incurs the lowest path cost when forwarding packets from that LAN to the root switch. The port through which the designated switch is attached to the LAN is called the designated port. Interfaces included in the spanning-tree instance are selected. Root ports and designated ports are put in the forwarding state. All interfaces not included in the spanning tree are blocked.

Election of the Root Switch

All switches in the Layer 2 network participating in spanning tree gather information about other switches in the network through an exchange of BPDU data messages. This exchange of messages results in these actions:

The election of a unique root switch for each spanning-tree instance The election of a designated switch for every switched LAN segment The removal of loops in the switched network by blocking Layer 2 interfaces connected to redundant links

For each VLAN, the switch with the highest switch priority (the lowest numerical priority value) is elected as the root switch. If all switches are configured with the default priority (32768), the switch with the lowest MAC address in the VLAN becomes the root switch. The switch priority value occupies the most significant bits of the bridge ID. When you change the switch priority value, you change the probability that the switch will be elected as the root switch. Configuring a higher value decreases the probability; a lower value increases the probability. The root switch is the logical center of the spanning-tree topology in a switched network. All paths that are not needed to reach the root switch from anywhere in the switched network are placed in the spanning-tree blocking mode.

Catalyst 3550 Multilayer Switch Software Configuration Guide 78-11194-07

15-3

Chapter 15 Understanding Spanning-Tree Features

Configuring STP

BPDUs contain information about the sending switch and its ports, including switch and MAC addresses, switch priority, port priority, and path cost. Spanning tree uses this information to elect the root switch and root port for the switched network and the root port and designated port for each switched segment.

Bridge ID, Switch Priority, and Extended System ID

The IEEE 802.1D standard requires that each switch has an unique bridge identifier (bridge ID), which determines the selection of the root switch. Because each VLAN is considered as a different logical bridge with PVST and PVRST, the same switch must have as many different bridge IDs as VLANs configured on it. Each VLAN on the switch has a unique 8-byte bridge ID; the two most-significant bytes are used for the switch priority, and the remaining six bytes are derived from the switch MAC address. In Release 12.1(8)EA1 and later, Catalyst 3550 switches support the 802.1T spanning-tree extensions. Some of the bits previously used for the switch priority are now used as the VLAN identifier. The result is that fewer MAC addresses are reserved for the switch, and a larger range of VLAN IDs can be supported, all while maintaining the uniqueness of the bridge ID. As shown in Table 15-1, the two bytes previously used for the switch priority are reallocated into a 4-bit priority value and a 12-bit extended system ID value equal to the VLAN ID. In earlier releases, the switch priority is a 16-bit value.
Table 15-1 Switch Priority Value and Extended System ID

Switch Priority Value Bit 16 32768 Bit 15 16384 Bit 14 8192 Bit 13 4096

Extended System ID (Set Equal to the VLAN ID) Bit 12 2048 Bit 11 1024 Bit 10 512 Bit 9 256 Bit 8 128 Bit 7 64 Bit 6 32 Bit 5 16 Bit 4 8 Bit 3 4 Bit 2 2 Bit 1 1

Spanning tree uses the extended system ID, the switch priority, and the allocated spanning-tree MAC address to make the bridge ID unique for each VLAN. With earlier releases, spanning tree used one MAC address per VLAN to make the bridge ID unique for each VLAN. Support for the extended system ID affects how you manually configure the root switch, the secondary root switch, and the switch priority of a VLAN. For more information, see the Configuring the Root Switch section on page 15-12, Configuring a Secondary Root Switch section on page 15-14, and Configuring the Switch Priority of a VLAN section on page 15-17.

Spanning-Tree Timers
Table 15-2 describes the timers that affect the entire spanning-tree performance.
Table 15-2 Spanning-Tree Timers

Variable Hello timer Forward-delay timer Maximum-age timer

Description Determines how often the switch broadcasts hello messages to other switches. Determines how long each of the listening and learning states last before the interface begins forwarding. Determines the amount of time the switch stores protocol information received on an interface.

Catalyst 3550 Multilayer Switch Software Configuration Guide

15-4

78-11194-07

Chapter 15

Configuring STP Understanding Spanning-Tree Features

Creating the Spanning-Tree Topology

In Figure 15-1, Switch A is elected as the root switch because the switch priority of all the switches is set to the default (32768) and Switch A has the lowest MAC address. However, because of traffic patterns, number of forwarding interfaces, or link types, Switch A might not be the ideal root switch. By increasing the priority (lowering the numerical value) of the ideal switch so that it becomes the root switch, you force a spanning-tree recalculation to form a new topology with the ideal switch as the root.
Figure 15-1 Spanning-Tree Topology

DP DP DP RP B RP = Root Port DP = Designated Port RP C A DP D RP DP DP DP

43568

When the spanning-tree topology is calculated based on default parameters, the path between source and destination end stations in a switched network might not be ideal. For instance, connecting higher-speed links to an interface that has a higher number than the root port can cause a root-port change. The goal is to make the fastest link the root port. For example, assume that one port on Switch B is a Gigabit Ethernet link and that another port on Switch B (a 10/100 link) is the root port. Network traffic might be more efficient over the Gigabit Ethernet link. By changing the spanning-tree port priority on the Gigabit Ethernet interface to a higher priority (lower numerical value) than the root port, the Gigabit Ethernet interface becomes the new root port.

Spanning-Tree Interface States

Propagation delays can occur when protocol information passes through a switched LAN. As a result, topology changes can take place at different times and at different places in a switched network. When an interface transitions directly from nonparticipation in the spanning-tree topology to the forwarding state, it can create temporary data loops. Interfaces must wait for new topology information to propagate through the switched LAN before starting to forward frames. They must allow the frame lifetime to expire for forwarded frames that have used the old topology. Each Layer 2 interface on a switch using spanning tree exists in one of these states:

BlockingThe interface does not participate in frame forwarding. ListeningThe first transitional state after the blocking state when the spanning tree determines that the interface should participate in frame forwarding. LearningThe interface prepares to participate in frame forwarding. ForwardingThe interface forwards frames. DisabledThe interface is not participating in spanning tree because of a shutdown port, no link on the port, or no spanning-tree instance running on the port.

Catalyst 3550 Multilayer Switch Software Configuration Guide 78-11194-07

15-5

Chapter 15 Understanding Spanning-Tree Features

Configuring STP

An interface moves through these states:

From initialization to blocking From blocking to listening or to disabled From listening to learning or to disabled From learning to forwarding or to disabled From forwarding to disabled

Figure 15-2 illustrates how an interface moves through the states.

Figure 15-2 Spanning-Tree Interface States

Power-on initialization Blocking state Listening state Learning state Forwarding state

Disabled state

When you power up the switch, STP is enabled by default, and every interface in the switch, VLAN, or network goes through the blocking state and the transitory states of listening and learning. Spanning tree stabilizes each interface at the forwarding or blocking state. When the spanning-tree algorithm places a Layer 2 interface in the forwarding state, this process occurs:
1. 2. 3. 4.

The interface is in the listening state while spanning tree waits for protocol information to transition the interface to the blocking state. While spanning tree waits the forward-delay timer to expire, it moves the interface to the learning state and resets the forward-delay timer. In the learning state, the interface continues to block frame forwarding as the switch learns end-station location information for the forwarding database. When the forward-delay timer expires, spanning tree moves the interface to the forwarding state, where both learning and frame forwarding are enabled.

Catalyst 3550 Multilayer Switch Software Configuration Guide

15-6

43569

78-11194-07

Chapter 15

Configuring STP Understanding Spanning-Tree Features

Blocking State
A Layer 2 interface in the blocking state does not participate in frame forwarding. After initialization, a BPDU is sent to each interface in the switch. A switch initially functions as the root until it exchanges BPDUs with other switches. This exchange establishes which switch in the network is the root or root switch. If there is only one switch in the network, no exchange occurs, the forward-delay timer expires, and the interfaces move to the listening state. An interface always enters the blocking state after switch initialization. An interface in the blocking state performs as follows:

Discards frames received on the port Discards frames switched from another interface for forwarding Does not learn addresses Receives BPDUs

Listening State
The listening state is the first state a Layer 2 interface enters after the blocking state. The interface enters this state when the spanning tree determines that the interface should participate in frame forwarding. An interface in the listening state performs as follows:

Discards frames received on the port Discards frames switched from another interface for forwarding Does not learn addresses Receives BPDUs

Learning State
A Layer 2 interface in the learning state prepares to participate in frame forwarding. The interface enters the learning state from the listening state. An interface in the learning state performs as follows:

Discards frames received on the port Discards frames switched from another interface for forwarding Learns addresses Receives BPDUs

Forwarding State
A Layer 2 interface in the forwarding state forwards frames. The interface enters the forwarding state from the learning state. An interface in the forwarding state performs as follows:

Receives and forwards frames received on the port Forwards frames switched from another port Learns addresses Receives BPDUs

Catalyst 3550 Multilayer Switch Software Configuration Guide 78-11194-07

15-7

Chapter 15 Understanding Spanning-Tree Features

Configuring STP

Disabled State
A Layer 2 interface in the disabled state does not participate in frame forwarding or in the spanning tree. An interface in the disabled state is nonoperational. A disabled interface performs as follows:

Discards frames received on the port Discards frames switched from another interface for forwarding Does not learn addresses Does not receive BPDUs

Spanning-Tree Address Management

IEEE 802.1D specifies 17 multicast addresses, ranging from 0x00180C2000000 to 0x0180C2000010, to be used by different bridge protocols. These addresses are static addresses that cannot be removed. Regardless of the spanning-tree state, the switch receives but does not forward packets destined for addresses between 0x0180C2000000 and 0x0180C200000F. If STP is enabled, the switch CPU receives packets destined for 0x0180C2000000 and 0x0180C2000010. If STP is disabled, the switch forwards those packets as unknown multicast addresses.

STP and IEEE 802.1Q Trunks

The IEEE 802.1Q standard for VLAN trunks imposes some limitations on the spanning-tree strategy for a network. The standard requires only one spanning-tree instance for all VLANs allowed on the trunks. However, in a network of Cisco switches connected through 802.1Q trunks, the switches maintain one spanning-tree instance for each VLAN allowed on the trunks. When you connect a Cisco switch to a non-Cisco device through an 802.1Q trunk, the Cisco switch uses per-VLAN spanning tree (PVST) to provide spanning-tree interoperability. If per-VLAN rapid spanning tree (PVRST ) is enabled, the switch uses PVRST instead of PVST to provide spanning-tree interoperability. The switch combines the spanning-tree instance of the 802.1Q VLAN of the trunk with the spanning-tree instance of the non-Cisco 802.1Q switch. However, all PVST or PVRST information is maintained by Cisco switches separated by a cloud of non-Cisco 802.1Q switches. The non-Cisco 802.1Q cloud separating the Cisco switches is treated as a single trunk link between the switches. PVST is automatically enabled on 802.1Q trunks, and no user configuration is required. The external spanning-tree behavior on access ports and Inter-Switch Link (ISL) trunk ports is not affected by PVST. For more information on 802.1Q trunks, see Chapter 11, Configuring VLANs.

VLAN-Bridge STP
Cisco VLAN-bridge STP is used with the fallback bridging feature (bridge groups), which forwards non-IP protocols such as DECnet between two or more VLAN bridge domains or routed ports. The VLAN-bridge STP allows the bridge groups to form a spanning tree on top of the individual VLAN spanning trees to prevent loops from forming if there are multiple connections among VLANs. It also prevents the individual spanning trees from the VLANs being bridged from collapsing into a single spanning tree.

Catalyst 3550 Multilayer Switch Software Configuration Guide

15-8

78-11194-07

Chapter 15

Configuring STP Understanding Spanning-Tree Features

To support VLAN-bridge STP, some of the spanning-tree timers are increased. To use the fallback bridging feature, you must have the enhanced multilayer software image installed on your switch. For more information, see Chapter 35, Configuring Fallback Bridging.

Spanning Tree and Redundant Connectivity

You can create a redundant backbone with spanning tree by connecting two switch interfaces to another device or to two different devices. Spanning tree automatically disables one interface but enables it if the other one fails, as shown in Figure 15-3. If one link is high-speed and the other is low-speed, the low-speed link is always disabled. If the speeds are the same, the port priority and port ID are added together, and spanning tree disables the link with the lowest value.
Figure 15-3 Spanning Tree and Redundant Connectivity

Active link Blocked link Workstations

You can also create redundant links between switches by using EtherChannel groups. For more information, see Chapter 29, Configuring EtherChannels.

Accelerated Aging to Retain Connectivity

The default for aging dynamic addresses is 5 minutes, the default setting of the mac-address-table aging-time global configuration command. However, a spanning-tree reconfiguration can cause many station locations to change. Because these stations could be unreachable for 5 minutes or more during a reconfiguration, the address-aging time is accelerated so that station addresses can be dropped from the address table and then relearned. The accelerated aging is the same as the forward-delay parameter value (spanning-tree vlan vlan-id forward-time seconds global configuration command) when the spanning tree reconfigures. Because each VLAN is a separate spanning-tree instance, the switch accelerates aging on a per-VLAN basis. A spanning-tree reconfiguration on one VLAN can cause the dynamic addresses learned on that VLAN to be subject to accelerated aging. Dynamic addresses on other VLANs can be unaffected and remain subject to the aging interval entered for the switch.

Catalyst 3550 Multilayer Switch Software Configuration Guide 78-11194-07

15-9

Chapter 15 Configuring Spanning-Tree Features

Configuring STP

Configuring Spanning-Tree Features

These sections describe how to configure spanning-tree features:

Default STP Configuration, page 15-10 STP Configuration Guidelines, page 15-11 Disabling STP, page 15-11 Configuring the Root Switch, page 15-12 Configuring a Secondary Root Switch, page 15-14 Configuring the Port Priority, page 15-15 Configuring the Path Cost, page 15-16 Configuring the Switch Priority of a VLAN, page 15-17 Configuring the Hello Time, page 15-18 Configuring the Forwarding-Delay Time for a VLAN, page 15-19 Configuring the Maximum-Aging Time for a VLAN, page 15-19 Configuring STP for Use in a Cascaded Stack, page 15-20

Default STP Configuration

Table 15-3 shows the default STP configuration.
Table 15-3 Default STP Configuration

Feature Enable state

Default Setting Enabled on VLAN 1. Up to 128 spanning-tree instances can be enabled.

Spanning-tree mode Switch priority Spanning-tree port priority (configurable on a per-interface basis) Spanning-tree port cost (configurable on a per-interface basis)

PVST (PVRST and MSTP are disabled). 32768. 128. 1000 Mbps: 4. 100 Mbps: 19. 10 Mbps: 100.

Spanning-tree VLAN port priority (configurable on a per-VLAN basis) Spanning-tree VLAN port cost (configurable on a per-VLAN basis)

128. 1000 Mbps: 4. 100 Mbps: 19. 10 Mbps: 100.

Hello time Forward-delay time Maximum-aging time

2 seconds. 15 seconds. 20 seconds.

Catalyst 3550 Multilayer Switch Software Configuration Guide

15-10

78-11194-07

Chapter 15

Configuring STP Configuring Spanning-Tree Features

STP Configuration Guidelines

If more VLANs are defined in the VTP than there are spanning-tree instances, you can enable STP on only 128 VLANs. The remaining VLANs operate with spanning tree disabled. If the number of VLANs exceeds 128, we recommend that you enable the MSTP to map multiple VLANs to a single spanning-tree instance. For more information, see the Chapter 16, Configuring RSTP and MSTP. For information on the recommended trunk port configuration, see theInteraction with Other Features section on page 11-19. If 128 instances of spanning tree are already in use, you can disable STP on one of the VLANs and then enable it on the VLAN where you want it to run. Use the no spanning-tree vlan vlan-id global configuration command to disable STP on a specific VLAN, and use the spanning-tree vlan vlan-id global configuration command to enable STP on the desired VLAN.

Caution

Switches that are not running spanning tree still forward BPDUs that they receive so that the other switches on the VLAN that have a running spanning-tree instance can break loops. Therefore, spanning tree must be running on enough switches to break all the loops in the network; for example, at least one switch on each loop in the VLAN must be running spanning tree. It is not absolutely necessary to run spanning tree on all switches in the VLAN; however, if you are running spanning tree only on a minimal set of switches, an incautious change to the network that introduces another loop into the VLAN can result in a broadcast storm.

Note

If you have already used all available spanning-tree instances on your switch, adding another VLAN anywhere in the VTP domain creates a VLAN that is not running spanning tree on that switch. If you have the default allowed list on the trunk ports of that switch, the new VLAN is carried on all trunk ports. Depending on the topology of the network, this could create a loop in the new VLAN that will not be broken, particularly if there are several adjacent switches that have all run out of spanning-tree instances. You can prevent this possibility by setting up allowed lists on the trunk ports of switches that have used up their allocation of spanning-tree instances. Setting up allowed lists is not necessary in many cases and can make it more labor-intensive to add another VLAN to the network. Spanning-tree commands determine the configuration of VLAN spanning-tree instances. You create a spanning-tree instance when you assign an interface to a VLAN. The spanning-tree instance is removed when the last interface is moved to another VLAN. You can configure switch and port parameters before a spanning-tree instance is created; these parameters are applied when the spanning-tree instance is created.

Disabling STP
STP is enabled by default on VLAN 1 and on all newly created VLANs up to the spanning-tree limit specified in Table 15-3. Disable STP only if you are sure there are no loops in the network topology.

Caution

When STP is disabled and loops are present in the topology, excessive traffic and indefinite packet duplication can drastically reduce network performance.

Catalyst 3550 Multilayer Switch Software Configuration Guide 78-11194-07

15-11

Chapter 15 Configuring Spanning-Tree Features

Configuring STP

Beginning in privileged EXEC mode, follow these steps to disable STP on a per-VLAN basis: Command
Step 1 Step 2

Purpose Enter global configuration mode. Disable STP on a per-VLAN basis. For vlan-id, you can specify a single VLAN identified by VLAN ID number, a range of VLANs separated by a hyphen, or a series of VLANs separated by a comma. The range is 1 to 4094.

configure terminal no spanning-tree vlan vlan-id

Step 3 Step 4 Step 5

end show spanning-tree vlan vlan-id copy running-config startup-config

Return to privileged EXEC mode. Verify your entries. (Optional) Save your entries in the configuration file.

To re-enable STP, use the spanning-tree vlan vlan-id global configuration command.

Configuring the Root Switch

The switch maintains a separate spanning-tree instance for each active VLAN configured on it. A bridge ID, consisting of the switch priority and the switch MAC address, is associated with each instance. For each VLAN, the switch with the lowest bridge ID becomes the root switch for that VLAN. To configure a switch to become the root for the specified VLAN, use the spanning-tree vlan vlan-id root global configuration command to modify the switch priority from the default value (32768) to a significantly lower value. When you enter this command, the switch checks the switch priority of the root switches for each VLAN. Because of the extended system ID support, the switch sets its own priority for the specified VLAN to 24576 if this value will cause this switch to become the root for the specified VLAN. If any root switch for the specified VLAN has a switch priority lower than 24576, the switch sets its own priority for the specified VLAN to 4096 less than the lowest switch priority. (4096 is the value of the least-significant bit of a 4-bit switch priority value as shown in Table 15-1 on page 15-4.)

Note

The spanning-tree vlan vlan-id root global configuration command fails if the value necessary to be the root switch is less than 1. Before Release 12.1(8)EA1, entering the spanning-tree vlan vlan-id root global configuration command on a Catalyst 3550 switch (no extended system ID) caused it to set its own switch priority for the specified VLAN to 8192 if this value caused this switch to become the root for the specified VLAN. If any root switch for the specified VLAN has a switch priority lower than 8192, the switch sets its own priority for the specified VLAN to 1 less than the lowest switch priority. These examples show the effect of the spanning-tree vlan vlan-id root command with and without the extended system ID support:

For Catalyst 3550 switches with the extended system ID (Release 12.1(8)EA1 and later), if all network devices in VLAN 20 have the default priority of 32768, entering the spanning-tree vlan 20 root primary command on the switch sets the switch priority to 24576, which causes this switch to become the root switch for VLAN 20.

Catalyst 3550 Multilayer Switch Software Configuration Guide

15-12

78-11194-07

Chapter 15

Configuring STP Configuring Spanning-Tree Features

For Catalyst 3550 switches without the extended system ID (software earlier than Release 12.1(8)EA1), if all network devices in VLAN 100 have the default priority of 32768, entering the spanning-tree vlan 100 root primary command on the switch sets the switch priority for VLAN 100 to 8192, which causes this switch to become the root switch for VLAN 100.

Note

If your network consists of switches that both do and do not support the extended system ID, it is unlikely that the switch with the extended system ID support will become the root switch. The extended system ID increases the switch priority value every time the VLAN number is greater than the priority of the connected switches running older software.

Note

The root switch for each spanning-tree instance should be a backbone or distribution switch. Do not configure an access switch as the spanning-tree primary root. Use the diameter keyword to specify the Layer 2 network diameter (that is, the maximum number of switch hops between any two end stations in the Layer 2 network). When you specify the network diameter, the switch automatically sets an optimal hello time, forward-delay time, and maximum-age time for a network of that diameter, which can significantly reduce the convergence time. You can use the hello keyword to override the automatically calculated hello time.

Note

After configuring the switch as the root switch, we recommend that you avoid manually configuring the hello time, forward-delay time, and maximum-age time by using the spanning-tree vlan vlan-id hello-time, spanning-tree vlan vlan-id forward-time, and the spanning-tree vlan vlan-id max-age global configuration commands. Beginning in privileged EXEC mode, follow these steps to configure a switch to become the root for the specified VLAN:

Command
Step 1 Step 2

Purpose Enter global configuration mode. Configure a switch to become the root for the specified VLAN.

configure terminal spanning-tree vlan vlan-id root primary [diameter net-diameter [hello-time seconds]]

For vlan-id, you can specify a single VLAN identified by VLAN ID number, a range of VLANs separated by a hyphen, or a series of VLANs separated by a comma. The range is 1 to 4094. (Optional) For diameter net-diameter, specify the maximum number of switches between any two end stations. The range is 2 to 7. (Optional) For hello-time seconds, specify the interval in seconds between the generation of configuration messages by the root switch. The range is 1 to 10 seconds; the default is 2 seconds. When you enter this command without the optional keywords, the switch recalculates the forward-time, hello-time, max-age, and priority settings. If you had previously configured these parameters, the switch recalculates them.

Note

Catalyst 3550 Multilayer Switch Software Configuration Guide 78-11194-07

15-13

Chapter 15 Configuring Spanning-Tree Features

Configuring STP

Command
Step 3 Step 4 Step 5

Purpose Return to privileged EXEC mode. Verify your entries. (Optional) Save your entries in the configuration file.

end show spanning-tree detail copy running-config startup-config

To return the switch to its default setting, use the no spanning-tree vlan vlan-id root global configuration command.

Configuring a Secondary Root Switch

When you configure a Catalyst 3550 switch that supports the extended system ID as the secondary root, the switch priority is modified from the default value (32768) to 28672. The switch is then likely to become the root switch for the specified VLAN if the primary root switch fails. This is assuming that the other network switches use the default switch priority of 32768 and therefore are unlikely to become the root switch. For Catalyst 3550 switches without the extended system ID support (software earlier than Release 12.1(8)EA1), the switch priority is changed to 16384. You can execute this command on more than one switch to configure multiple backup root switches. Use the same network diameter and hello-time values as you used when you configured the primary root switch with the spanning-tree vlan vlan-id root primary global configuration command. Beginning in privileged EXEC mode, follow these steps to configure a switch to become the secondary root for the specified VLAN: Command
Step 1 Step 2

Purpose Enter global configuration mode. Configure a switch to become the secondary root for the specified VLAN.

configure terminal spanning-tree vlan vlan-id root secondary [diameter net-diameter [hello-time seconds]]

For vlan-id, you can specify a single VLAN identified by VLAN ID number, a range of VLANs separated by a hyphen, or a series of VLANs separated by a comma. The range is 1 to 4094. (Optional) For diameter net-diameter, specify the maximum number of switches between any two end stations. The range is 2 to 7. (Optional) For hello-time seconds, specify the interval in seconds between the generation of configuration messages by the root switch. The range is 1 to 10 seconds; the default is 2 seconds.

Use the same network diameter and hello-time values that you used when configuring the primary root switch. See the Configuring the Root Switch section on page 15-12.
Step 3 Step 4 Step 5

end show spanning-tree detail copy running-config startup-config

Return to privileged EXEC mode. Verify your entries. (Optional) Save your entries in the configuration file.

Catalyst 3550 Multilayer Switch Software Configuration Guide

15-14

78-11194-07

Chapter 15

Configuring STP Configuring Spanning-Tree Features

To return the switch to its default setting, use the no spanning-tree vlan vlan-id root global configuration command.

Configuring the Port Priority

If a loop occurs, spanning tree uses the port priority when selecting an interface to put into the forwarding state. You can assign higher priority values (lower numerical values) to interfaces that you want selected first and lower priority values (higher numerical values) that you want selected last. If all interfaces have the same priority value, spanning tree puts the interface with the lowest interface number in the forwarding state and blocks the other interfaces. Beginning in privileged EXEC mode, follow these steps to configure the port priority of an interface: Command
Step 1 Step 2

Purpose Enter global configuration mode. Enter interface configuration mode, and specify an interface to configure. Valid interfaces include physical interfaces and port-channel logical interfaces (port-channel port-channel-number).

configure terminal interface interface-id

Step 3

spanning-tree port-priority priority

Configure the port priority for an interface. For priority, the range is 0 to 240 in increments of 16. The default is 128. The lower the number, the higher the priority. Valid priority values are 0, 16, 32, 48, 64, 80, 96, 112, 128, 144, 160, 176, 192, 208, 224, and 240. All other values are rejected.

Step 4

spanning-tree vlan vlan-id port-priority priority

Configure the VLAN port priority for an interface.

For vlan-id, you can specify a single VLAN identified by VLAN ID number, a range of VLANs separated by a hyphen, or a series of VLANs separated by a comma. The range is 1 to 4094. For priority,the range is 0 to 240 in increments of 16. The default is 128. The lower the number, the higher the priority. Valid priority values are 0, 16, 32, 48, 64, 80, 96, 112, 128, 144, 160, 176, 192, 208, 224, and 240. All other values are rejected.

Step 5 Step 6

end show spanning-tree interface interface-id or show spanning-tree vlan vlan-id

Return to privileged EXEC mode. Verify your entries.

Step 7

copy running-config startup-config

(Optional) Save your entries in the configuration file.

Catalyst 3550 Multilayer Switch Software Configuration Guide 78-11194-07

15-15

Chapter 15 Configuring Spanning-Tree Features

Configuring STP

Note

The show spanning-tree interface interface-id privileged EXEC command displays information only if the port is in a link-up operative state. Otherwise, you can use the show running-config interface privileged EXEC command to confirm the configuration. To return the interface to its default setting, use the no spanning-tree [vlan vlan-id] port-priority interface configuration command. For information on how to configure load sharing on trunk ports by using spanning-tree port priorities, see the Load Sharing Using STP section on page 11-23.

Configuring the Path Cost

The spanning-tree path cost default value is derived from the media speed of an interface. If a loop occurs, spanning tree uses cost when selecting an interface to put in the forwarding state. You can assign lower cost values to interfaces that you want selected first and higher cost values that you want selected last. If all interfaces have the same cost value, spanning tree puts the interface with the lowest interface number in the forwarding state and blocks the other interfaces. Beginning in privileged EXEC mode, follow these steps to configure the cost of an interface: Command
Step 1 Step 2

Purpose Enter global configuration mode. Enter interface configuration mode, and specify an interface to configure. Valid interfaces include physical interfaces and port-channel logical interfaces (port-channel port-channel-number). Configure the cost for an interface. If a loop occurs, spanning tree uses the path cost when selecting an interface to place into the forwarding state. A lower path cost represents higher-speed transmission. For cost, the range is 1 to 200000000; the default value is derived from the media speed of the interface.

configure terminal interface interface-id

Step 3

spanning-tree cost cost

Step 4

spanning-tree vlan vlan-id cost cost

Configure the cost for a VLAN. If a loop occurs, spanning tree uses the path cost when selecting an interface to place into the forwarding state. A lower path cost represents higher-speed transmission.

For vlan-id, you can specify a single VLAN identified by VLAN ID number, a range of VLANs separated by a hyphen, or a series of VLANs separated by a comma. The range is 1 to 4094. For cost, the range is 1 to 200000000; the default value is derived from the media speed of the interface.

Step 5

end

Return to privileged EXEC mode.

Catalyst 3550 Multilayer Switch Software Configuration Guide

15-16

78-11194-07

Chapter 15

Configuring STP Configuring Spanning-Tree Features

Command
Step 6

Purpose Verify your entries.

show spanning-tree interface interface-id or show spanning-tree vlan vlan-id

Step 7

copy running-config startup-config

(Optional) Save your entries in the configuration file.

Note

The show spanning-tree interface interface-id privileged EXEC command displays information only for ports that are in a link-up operative state. Otherwise, you can use the show running-config privileged EXEC command to confirm the configuration. To return the interface to its default setting, use the no spanning-tree [vlan vlan-id] cost interface configuration command. For information on how to configure load sharing on trunk ports by using spanning-tree path costs, see the Load Sharing Using STP section on page 11-23.

Configuring the Switch Priority of a VLAN

You can configure the switch priority and make it more likely that the switch will be chosen as the root switch.

Note

Exercise care when using this command. For most situations, we recommend that you use the spanning-tree vlan vlan-id root primary and the spanning-tree vlan vlan-id root secondary global configuration commands to modify the switch priority. Beginning in privileged EXEC mode, follow these steps to configure the switch priority of a VLAN:

Command
Step 1 Step 2

Purpose Enter global configuration mode. Configure the switch priority of a VLAN.

configure terminal spanning-tree vlan vlan-id priority priority

For vlan-id, you can specify a single VLAN identified by VLAN ID number, a range of VLANs separated by a hyphen, or a series of VLANs separated by a comma. The range is 1 to 4094. For priority, the range is 0 to 61440 in increments of 4096; the default is 32768. The lower the number, the more likely the switch will be chosen as the root switch. Valid priority values are 4096, 8192, 12288, 16384, 20480, 24576, 28672, 32768, 36864, 40960, 45056, 49152, 53248, 57344, and 61440. All other values are rejected.

Step 3 Step 4 Step 5

end show spanning-tree vlan vlan-id copy running-config startup-config

Return to privileged EXEC mode. Verify your entries. (Optional) Save your entries in the configuration file.

Catalyst 3550 Multilayer Switch Software Configuration Guide 78-11194-07

15-17

Chapter 15 Configuring Spanning-Tree Features

Configuring STP

To return the switch to its default setting, use the no spanning-tree vlan vlan-id priority global configuration command.

Configuring the Hello Time

You can configure the interval between the generation of configuration messages by the root switch by changing the hello time.

Note

Exercise care when using this command. For most situations, we recommend that you use the spanning-tree vlan vlan-id root primary and the spanning-tree vlan vlan-id root secondary global configuration commands to modify the hello time. Beginning in privileged EXEC mode, follow these steps to configure the hello time of a VLAN:

Command
Step 1 Step 2

Purpose Enter global configuration mode. Configure the hello time of a VLAN. The hello time is the interval between the generation of configuration messages by the root switch. These messages mean that the switch is alive.

configure terminal spanning-tree vlan vlan-id hello-time seconds

For vlan-id, you can specify a single VLAN identified by VLAN ID number, a range of VLANs separated by a hyphen, or a series of VLANs separated by a comma. The range is 1 to 4094. For seconds, the range is 1 to 10; the default is 2.

Step 3 Step 4 Step 5

end show spanning-tree vlan vlan-id copy running-config startup-config

Return to privileged EXEC mode. Verify your entries. (Optional) Save your entries in the configuration file.

To return the switch to its default setting, use the no spanning-tree vlan vlan-id hello-time global configuration command.

Catalyst 3550 Multilayer Switch Software Configuration Guide

15-18

78-11194-07

Chapter 15

Configuring STP Configuring Spanning-Tree Features

Configuring the Forwarding-Delay Time for a VLAN

Beginning in privileged EXEC mode, follow these steps to configure the forwarding-delay time for a VLAN: Command
Step 1 Step 2

Purpose Enter global configuration mode. Configure the forward time of a VLAN. The forward delay is the number of seconds a port waits before changing from its spanning-tree learning and listening states to the forwarding state.

configure terminal spanning-tree vlan vlan-id forward-time seconds

For vlan-id, you can specify a single VLAN identified by VLAN ID number, a range of VLANs separated by a hyphen, or a series of VLANs separated by a comma. The range is 1 to 4094. For seconds, the range is 4 to 30; the default is 15.

Step 3 Step 4 Step 5

end show spanning-tree vlan vlan-id copy running-config startup-config

Return to privileged EXEC mode. Verify your entries. (Optional) Save your entries in the configuration file.

To return the switch to its default setting, use the no spanning-tree vlan vlan-id forward-time global configuration command.

Configuring the Maximum-Aging Time for a VLAN

Beginning in privileged EXEC mode, follow these steps to configure the maximum-aging time for a VLAN: Command
Step 1 Step 2

Purpose Enter global configuration mode. Configure the maximum-aging time of a VLAN. The maximum-aging time is the number of seconds a switch waits without receiving spanning-tree configuration messages before attempting a reconfiguration.

configure terminal spanning-tree vlan vlan-id max-age seconds

For vlan-id, you can specify a single VLAN identified by VLAN ID number, a range of VLANs separated by a hyphen, or a series of VLANs separated by a comma. The range is 1 to 4094. For seconds, the range is 6 to 40; the default is 20.

Step 3 Step 4 Step 5

end show spanning-tree vlan vlan-id copy running-config startup-config

Return to privileged EXEC mode. Verify your entries. (Optional) Save your entries in the configuration file.

To return the switch to its default setting, use the no spanning-tree vlan vlan-id max-age global configuration command.

Catalyst 3550 Multilayer Switch Software Configuration Guide 78-11194-07

15-19

Chapter 15 Displaying the Spanning-Tree Status

Configuring STP

Configuring STP for Use in a Cascaded Stack

STP uses default values that can be reduced when configuring your switch in cascaded configurations. If a root switch is part of a cluster that is one switch from a cascaded stack, you can customize spanning tree to reconverge more quickly after a switch failure. Figure 15-4 shows switches in three cascaded stacks that use the GigaStack GBIC. Table 15-4 shows the default STP settings and those that are acceptable for these configurations.
Table 15-4 Default and Acceptable STP Parameter Settings (in seconds)

STP Parameter Hello Time Max Age Forwarding Delay

STP Default 2 20 15

Acceptable for Option 1 Acceptable for Option 2 1 6 4 1 10 7

Acceptable for Option 3 1 6 4

Figure 15-4 Gigabit Ethernet Stack

Catalyst 3550 series switch

Catalyst 2950, Cisco 7000 2955, or 3550 router switches

Catalyst 2950, 2955, or 3550 switches

Catalyst 2950, 2955, or 3550 switches

Catalyst 3550 or 6000 series backbone Catalyst 6000 switch

Layer 3 backbone

Cisco 7000 router

74621

Option 1: standalone cascaded cluster

Option 2: cascaded cluster connected to a Layer 2 backbone

Option 3: cascaded cluster connected to a Layer 3 backbone

Displaying the Spanning-Tree Status

To display the spanning-tree status, use one or more of the privileged EXEC commands in Table 15-5:
Table 15-5 Commands for Displaying Spanning-Tree Status

Command show spanning-tree active show spanning-tree detail

Purpose Displays spanning-tree information on active interfaces only. Displays a detailed summary of interface information.

Catalyst 3550 Multilayer Switch Software Configuration Guide

15-20

78-11194-07

Chapter 15

Configuring STP Displaying the Spanning-Tree Status

Table 15-5 Commands for Displaying Spanning-Tree Status (continued)

Command show spanning-tree interface interface-id show spanning-tree summary [totals]

Purpose Displays spanning-tree information for the specified interface. Displays a summary of port states or displays the total lines of the STP state section.

For information about other keywords for the show spanning-tree privileged EXEC command, refer to the command reference for this release.

Catalyst 3550 Multilayer Switch Software Configuration Guide 78-11194-07

15-21

Chapter 15 Displaying the Spanning-Tree Status

Configuring STP

Catalyst 3550 Multilayer Switch Software Configuration Guide

15-22

78-11194-07