Scribd
Upload
51 views

PDMS Commands Piping Modeling: Axes at CE To Check The Axes of Component Like North, South, East, West Direction

This document lists PDMS commands for piping and equipment modeling. It includes over 50 piping commands for tasks like checking component attributes, connecting pipes, aligning components, and adding insulation. It also lists over 10 equipment modeling commands for creating sites, zones, equipment, subequipment, nozzles, boxes, cylinders, and connecting design points. The commands allow designers to efficiently model in PDMS.

Uploaded by

mshadabk
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
51 views

PDMS Commands Piping Modeling: Axes at CE To Check The Axes of Component Like North, South, East, West Direction

This document lists PDMS commands for piping and equipment modeling. It includes over 50 piping commands for tasks like checking component attributes, connecting pipes, aligning components, and adding insulation. It also lists over 10 equipment modeling commands for creating sites, zones, equipment, subequipment, nozzles, boxes, cylinders, and connecting design points. The commands allow designers to efficiently model in PDMS.

Uploaded by

mshadabk
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

PDMS Commands Piping Modeling

These are the PDMS Piping Commands which are used while modeling in the PDMS. Designer can use this commands while modeling in PDMS. These PDMS piping commands are helps to designer while modeling 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Axes at CE= to check the axes of component like North, South, East, West direction Q axes at ph= to check the head of the branch of the pipe. Q axes at pt= to check the tail of the branch of the pipe. Q Hstu= to show the branch head tube attribute Q Lstu= to show the branch tail tube attribute Q Hbore= to check the arrive bore or diameter of the component Q Tbore= to check the leave bore or diameter of the component Q Spre= to check the specification of the particular component Q pspec= to check material class of the pipe. New elbow choo all= to create new elbow through command line New tee choo all= to create new tee through command line New gasket choo all= to create new gasket through command line New flange choo all= to create new flange through command line New olet choo all= to create new olet through command line

15. Unclaim all= to remove claim the by user so other user can work in that pipe, equipment, member,structure. 16. Getwork= to refresh the design model. After get work all the change done any user will show in the model. 17. 18. 19. Axes at hpos= To check the branch head axes Axes at tpos= To check the branch tail axes Q ltle= to check the length of the spool between the two component

20. Conn ph to fir member= to connect the branch head to first member of the next branch by common line 21. Conn pt to fir member= to connect the branch tail to last member of the next branch by common line --> 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. Q ori = to check the orientation of the component Dist= to give the distance between two component Clea= to give the spool length between the two component Conn= connect to the member Fconn= to component forcefully Q styp= to check the component selection type Q dtxr= to check the detail text description of the component Q mtxx= to check the material of the component Q mode= to check the mode weather it in forward mode or backward mode Q para= to check the parameter of the component Dir tow next= to connect the next member by direction Q ref= to check the reference

34. Add all the pipe within vol ce 500= all pipes to added in the area 500 around the selected component. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. 45. 46. 47. 48. 49. 50. 51. 52. 53. 54. 55. 56. 57. 58. --> Incl= to include the component from one branch to other branch Ori and p3 is up= to orientate the point 3 of the tee in up direction Own= navigate the owner of component Q angle= to check the angle of the component Q atle= to check the length of the first tube of the branch Attype ccnn= comment attachment without dimensions Attype cccc= comment attachment with dimensions Attype xxxx= to set the attachment for isometric break up Ch ce= to check the data inconsistency Dir tow next elb= to align the elbow with next elbow Dir tow id@= to align the elbow by using mouse click on the component Q hcon= to check head connection attached with which branch Q tcon= to check tail connection attached with which branch Q ispec= to check the insulation of pipe Ispec nulref= to remove the insulation of the pipe Mtoc dotd= to appear the component in doted in the isometric Mtoc off= to remove the material off the component. With this command material of the component will not appear in isometric Nex conn= connect to next component Nex thro ce= align the next component in same direction Q p3 = to check the p3 point of the component Q pa= to check arrive point Q pl= to check the leave point Attype flow= to create the flow direction attachment

PDMS commands Equipment Modeling


1. 2. 3. 4. 5. 6. 7. 8. 9. pdms 10. 11. New site= for creating the new site in pdms New zone= for creating the new zone in pdms New equi= for creating the new equipment in pdms New sube= for creating the new sub equipment in pdms New nozzle= for creating the new nozzle in the pdms New box= for creating new box in the pdms New cylinder= for creating new cylinder in the pdms Conn idp to idp= to connect design point of two cylinder/box etc. Mark with (nam) all nozz for ce= to mark the all nozzle of equipment with name in Q level= to check the level of the component Axes at p1= to check p1 point of the primitive

12. 13. 500

Axes at p2= to check p2 point of the primitive New cylinder copy prev by n 500= to copy the previous cylinder by north direction by

You might also like