11 EnSight Data Formats

This section describes the format for all readable and writable files in EnSight which you may need access to. The formats described are only for those files that are specific to EnSight. We do not describe data formats not developed by CEI (for example, data formats for various analysis codes). For information about these formats, consult the applicable creator. Note: If you are using this documentation to produce your own data translator, please make sure that you follow the instructions exactly as specified. In many cases, EnSight reads data in blocks to improve performance. If the format is not followed, the calculations of how much to read for a block will be thrown off. EnSight does little in the way of error checking data files when they are read. In this respect, EnSight sacrifices robustness for performance. As an aid to developing translators, a C library is provided that supports input and output of the native EnSight data format in both ASCII and binary versions. Section 11.1, EnSight Gold Casefile Format describes in detail the EnSight Gold case, geometry, and variable file formats. Section 11.2, EnSight6 Casefile Format describes in detail the EnSight6 case, geometry, and variable file formats. Section 11.3, EnSight5 Format describes in detail the EnSight5 geometry and variable file formats. Section 11.4, FAST UNSTRUCTURED Results File Format describes the executive .res file that can be used with FAST unstructured solution and function files. Section 11.5, FLUENT UNIVERSAL Results File Format describes the executive .res file that can be used with FLUENT Universal files for transient models. Section 11.6, Movie.BYU Results File Format describes the executive .res file that can be used with Movie.BYU files. Section 11.7, PLOT3D Results File Format describes the executive .res file that can be used with PLOT3D solution and function files. Section 11.8, Server-of-Server Casefile Format describes the format of the casefile used with the server-of-server capability of EnSight. Section 11.9, Periodic Matchfile Format describes the format of the file which can be used to explicitly specify which nodes match from one periodic instance to the next. Section 11.10, XY Plot Data Format describes the format of the file containing XY plot data.

EnSight 7 User Manual

11-1

11.1 EnSight Gold Casefile Format

11.1 EnSight Gold Casefile Format

Include in this section: EnSight Gold General Description EnSight Gold Geometry File Format EnSight Gold Case File Format EnSight Gold Wild Card Name Specification EnSight Gold Variable File Format EnSight Gold Per_Node Variable File Format EnSight Gold Per_Element Variable File Format EnSight Gold Undefined Variable Values Format EnSight Gold Partial Variable Values Format EnSight Gold Measured/Particle File Format

EnSight Gold General Description

EnSight Gold data consists of the following files: Case (required) (points to all other needed files including model geometry, variables, and possibly measured geometry and variables) EnSight makes no assumptions regarding the physical significance of the scalar, vector, 2nd order symmetric tensor, and complex variables. These files can be from any discipline. For example, the scalar file can include such things as pressure, temperature, and stress. The vector file can be velocity, displacement, or any other vector data, etc. In addition, EnSight Gold format handles "undefined" as well as "partial" variable values. (See appropriate subsections later in this chapter for details.) All variable results for EnSight Gold format are contained in disk filesone variable per file. Additionally, if there are multiple time steps, there must either be a set of disk files for each time step (transient multiple-file format), or all time steps of a particular variable or geometry in one disk file each (transient single-file format). Sources of EnSight Gold format data include the following: Data that can be translated to conform to the EnSight Gold data format (including being written from EnSight itself using the Save Geometric Entities option under File->Save) Data that originates from one of the translators supplied with the EnSight application The EnSight Gold format supports an unstructured defined element set as shown in the figure on the following page. Unstructured data must be defined in this element set. Elements that do not conform to this set must either be subdivided or discarded.

11-2

EnSight 7 User Manual

11.1 EnSight Gold General Description

The EnSight Gold format also supports the same structured block data format as EnSight6, which is very similar to the PLOT3D format. A given EnSight Gold model may have either unstructured data, structured data, or a mixture of both. This format is somewhat similar to the EnSight6 format, but differs enough to allow for more efficient reading of the data. It is intended for 3D, binary, big data models. Note: While an ASCII format is available, it is not intended for use with large models and is in fact subject to limitations such as integer lengths of 10 digits. Use the binary format if your model will exceed 10 digits for node or element numbers or labels. Starting with version 7, EnSight writes out all model and variable files in EnSight Gold format. Thus, it can be read by all version 7 EnSight licenses (i.e. standard, gold, and custom licenses).

EnSight 7 User Manual

11-3

11.1 EnSight Gold General Description

Supported EnSight Gold Elements

The elements that are supported by the EnSight Gold format are: 1 point 1 two node bar 2 1 2 three node bar n 3 1 2 n-sided polygon

. . .
7

3 6 1 2 1

3 5 4 2

3 8

3 6

three node triangle

six node triangle 4 8 9 7 6 1 10 3 2

four node quadrangle 5

eight node quadrangle 5 12 10 4 9 6 13 11

1 2

1 5

4 1

8 7 2

2 5 node pyramid 7 8 5 17 1 16 13 12 4 20

four node tetrahedron

ten node tetrahedron 8

13 node pyramid 15 14 11 10 7 19 3

6 18

2 eight node hexahedron 4 1 5 2 6 3

9 2 twenty node hexahedron 4 13 1 10 7 2 12 9 5 14 6 15 11 3 8

six node pentahedron (wedge)

Figure 2-1

fifteen node pentahedron (wedge)

Supported EnSight Gold Elements

11-4

EnSight 7 User Manual

11.1 EnSight Gold Geometry File Format

EnSight Gold Geometry File Format

The EnSight Gold format is part based for both unstructured and structured data. There is no global coordinate array that each part references, but instead - each part contains its own local coordinate array. Thus, the node numbers in element connectivities refer to the coordinate array index, not a node id or label. This is different than the EnSight6 format! The EnSight Gold format consists of keywords followed by information. The following items are important when working with EnSight Gold geometry files: 1. Node ids are optional. In this format they are strictly labels and are not used in the connectivity definition. The element connectivities are based on the local implied node number of the coordinate array in each part, which is sequential starting at one. If you let EnSight assign node IDs, this implied internal numbering is used. If node IDs are set to off, they are numbered internally, however, you will not be able to display or query on them. If you have node IDs given in your data, you can have EnSight ignore them by specifying node id ignore. Using this option may reduce some of the memory taken up by the Client and Server, but display and query on the nodes will not be available. 2. Element ids are optional. If you specify element IDs, or you let EnSight assign them, you can show them on the screen. If they are set to off, you will not be able to show or query on them. If you have element IDs given in your data you can have EnSight ignore them by specifying element id ignore. Using this option will reduce some of the memory taken up by the Client and Server. This may or may not be a significant amount, and remember that display and query on the elements will not be available. 3. Model extents can be defined in the file so EnSight will not have to determine these while reading in data. If they are not included, EnSight will compute them, but will not actually do so until a dataset query is performed the first time. 4. The format of integers and real numbers must be followed (See the Geometry Example below). 5. ASCII Integers are written out using the following integer format: From C: 10d format From FORTRAN: i10 format Note: this size of integer format places a limitation on the number of nodes and the node and element labels that can make up a model. Use the binary format for large models! ASCII Real numbers are written out using the following floating-point format: From C: From FORTRAN:
12.5e format e12.5 format

The number of integers or reals per line must also be followed! 6. By default, a Part is processed to show the outside boundaries. This representation is loaded to the Client host system when the geometry file is read (unless other attributes have been set on the workstation, such as feature angle).
EnSight 7 User Manual 11-5

11.1 EnSight Gold Geometry File Format

7. Coordinates for unstructured data must be defined within each part. This is normally done before any elements are defined within a part, but does not have to be. The different elements can be defined in any order (that is, you can define a hexa8 before a bar2). 8. Parts which contain n-sided polygon elements may not contain other element types. They can however contain several different n-sided sections. 9. A Part containing structured data cannot contain any unstructured element types or more than one block. Each structured Part is limited to a single block. A structured block is indicated by following the Part description line with a block line. The various options include: block block rectilinear block uniform block iblanked block rectilinear iblanked block uniform iblanked (default is curvilinear) (uses i,j,k delta vectors) (uses i,j,k delta values)

An iblanked block must contain an additional integer array of values at each node, traditionally called the iblank array. Valid iblank values for the EnSight Gold format are:
0 for nodes which are exterior to the model, sometimes called blanked-out nodes 1 for nodes which are interior to the model, thus in the free stream and to be used <0 or >1 for any kind of boundary nodes In EnSights structured Part building dialog, the iblank option selected will control which portion of the structured block is created. Thus, from the same structured block, the interior flow field part as well as a symmetry boundary part could be created.

Note: By default EnSight does not do any partial cell iblank processing. Namely, only complete cells containing no exterior nodes are created. It is possible to obtain partial cell processing by issuing the test:partial_cells_on command in the Command Dialog before reading the file.

11-6

EnSight 7 User Manual

11.1 EnSight Gold Geometry File Format

Generic Format

Usage Notes: In general a part can contain several different element types. There are two exceptions to this rule. Parts containing nsided polygons cannot contain any other element type, and block parts can contain one and only one block.
element type

can be any of:

point tria3 quad8 tetra10 penta6 hexa20

bar2 tria6 nsided pyramid5 penta15

bar3 quad4 tetra4 pyramid13 hexa8

# = a part number nn = total number of nodes in a part ne = number of elements of a given type np = number of nodes per element for a given id_* = node or element id number x_* = x component y_* = y component z_* = z component e*_* = node number for an element ib_* = iblanking value

element type

[ ] contain optional portions < > contain choices indicates the beginning of an unformatted sequential FORTRAN binary indicates the end of an unformatted sequential FORTRAN binary write

write

EnSight 7 User Manual

11-7

11.1 EnSight Gold Geometry File Format

C Binary form:
C Binary description line 1 description line 2 node id <off/given/assign/ignore> element id <off/given/assign/ignore> [extents xmin xmax ymin ymax zmin zmax] part # description line coordinates nn [id_n1 id_n2 ... id_nn] x_n1 x_n2 ... x_nn y_n1 y_n2 ... y_nn z_n1 z_n2 ... z_nn element type ne [id_n1 id_n2 ... id_ne] e1_n1 e1_n2 ... e1_np e2_n1 e2_n2 ... e2_np . . ne_n1 ne_n2 ... ne_np element type . . part . . part # description line block [iblanked] i j k # mm = i*j*k x_m1 x_m2 ... x_mm y_m1 y_m2 ... y_mm z_m1 z_m2 ... z_mm [ib_m1 ib_m2 ... ib_mm] part # description line block rectilinear [iblanked] i j k # mm = i*j*k x_1 x_2 ... x_i y_1 y_2 ... y_j z_1 z_2 ... z_k [ib_m1 ib_m2 ... ib_mm] part # description line block uniform [iblanked] i j k # mm = i*j*k x_origin y_origin z_origin x_delta y_delta z_delta [ib_m1 ib_m2 ... ib_mm] 80 80 80 80 80 6 80 1 80 80 1 nn nn nn nn 80 1 ne chars chars chars chars chars floats chars int chars chars int ints floats floats floats chars int ints

ne*np ints 80 chars

80 chars

80 chars 1 int 80 chars 80 chars 3 ints mm floats mm floats mm floats mm ints 80 chars 1 int 80 chars 80 chars 3 ints i floats j floats k floats mm ints 80 chars 1 int 80 chars 80 chars 3 ints 3 floats 3 floats mm ints

11-8

EnSight 7 User Manual

11.1 EnSight Gold Geometry File Format

Fortran Binary form:

Fortran Binary description line 1 description line 2 node id <off/given/assign/ignore> element id <off/given/assign/ignore> [extents xmin xmax ymin ymax zmin zmax] part # description line coordinates nn [id_n1 id_n2 ... id_nn] x_n1 x_n2 ... x_nn y_n1 y_n2 ... y_nn z_n1 z_n2 ... z_nn element type ne [id_n1 id_n2 ... id_ne] e1_n1 e1_n2 ... e1_np e2_n1 e2_n2 ... e2_np . . ne_n1 ne_n2 ... ne_np element type . . part . . part # description line block [iblanked] i j k # mm = i*j*k x_m1 x_m2 ... x_mm y_m1 y_m2 ... y_mm z_m1 z_m2 ... z_mm [ib_m1 ib_m2 ... ib_mm] part # description line block rectilinear [iblanked] i j k # mm = i*j*k x_1 x_2 ... x_i y_1 y_2 ... y_j z_1 z_2 ... z_k [ib_m1 ib_m2 ... ib_mm] part # description line block uniform [iblanked] i j k # mm = i*j*k x_origin y_origin z_origin x_delta y_delta z_delta [ib_m1 ib_m2 ... ib_mm] 80 80 80 80 80 6 80 1 80 80 1 nn nn nn nn 80 1 ne chars chars chars chars chars floats chars int chars chars int ints floats floats floats chars int ints

ne*np ints 80 chars

80 chars

80 chars 1 int 80 chars 80 chars 3 ints mm floats mm floats mm floats mm ints 80 chars 1 int 80 chars 80 chars 3 ints i floats j floats k floats mm ints 80 chars 1 int 80 chars 80 chars 3 ints 3 floats 3 floats mm ints

EnSight 7 User Manual

11-9

11.1 EnSight Gold Geometry File Format

ASCII form:
description line 1 description line 2 node id <off/given/assign/ignore> element id <off/given/assign/ignore> [extents xmin xmax ymin ymax zmin zmax] part # description line coordinates nn [id_n1 id_n2 . . id_nn] x_n1 x_n2 . . x_nn y_n1 y_n2 . . y_nn z_n1 z_n2 . . z_nn element type ne [id_n1 id_n2 . . id_ne] e1_n1 e1_n2 ... e1_np e2_n1 e2_n2 ... e2_np . . ne_n1 ne_n2 ... ne_np element type . . part . . part # description line block [iblanked] i j k # mm = i*j*k x_m1 x_m2 . A (max of 79 typ) A A A A 2E12.5 2E12.5 2E12.5 A I10 A A I10 I10 1/line (nn)

E12.5 1/line (nn)

E12.5 1/line (nn)

E12.5 1/line (nn)

A I10 I10

1/line (ne)

I10 np/line (ne lines)

A I10 A A 3I10 E12.5 1/line (mm)

11-10

EnSight 7 User Manual

11.1 EnSight Gold Geometry File Format . x_mm y_m1 y_m2 . . y_mm z_m1 z_m2 . . z_mm [ib_m1 ib_m2 . . ib_mm] part # description line block rectilinear [iblanked] i j k # mm = i*j*k x_1 x_2 . . x_i y_1 y_2 . . y_j z_1 z_2 . . z_k [ib_m1 ib_m2 . . ib_mm] part # description line block uniform [iblanked] i j k # mm = i*j*k x_origin y_origin z_origin x_delta y_delta z_delta [ib_m1 ib_m2 . . ib_mm]

E12.5 1/line (mm)

E12.5 1/line (mm)

I10

1/line (mm)

A I10 A A 3I10 E12.5 1/line (i)

E12.5 1/line (j)

E12.5 1/line (k)

I10

1/line (mm)

A I10 A A 3I10 E12/5 E12/5 E12/5 E12.5 E12.5 E12.5 I10 1/line (mm)

EnSight 7 User Manual

11-11

11.1 EnSight Gold Geometry File Format

Notes: If node id is given or ignore, the [id] section must be there for each part. If element id is given or ignore, the [id] section must be there for each element type of each part If iblanked is there, the [ib] section must be there for the block. x, y, and z coordinates are mandatory, even if a 2D problem. If block rectilinear, then the x, y, z coordinates change to the x, y, and z delta vectors. If block uniform, then the x, y, z coordinates change to the x, y, z coordinates of the origin and the x, y, and z delta values. Ids are just labels, the coordinate (or element) order is implied. Element blocks for nsided elements contain an additional section - the number of nodes in each element. See below C Binary form of element block, if nsided:
nsided ne [id_n1 id_n2 ... id_ne] np1 np2 ... npne e1_n1 e1_n2 ... e1_np1 e2_n1 e2_n2 ... e2_np2 . . ne_n1 ne_n2 ... ne_npne 80 1 ne ne chars int ints ints

This data is needed

np1+np2+...+npne ints

Fortran Binary form of element block, if nsided:

nsided ne [id_n1 id_n2 ... id_ne] np1 np2 ... npne This data is needed e1_n1 e1_n2 ... e1_np1 e2_n1 e2_n2 ... e2_np2 . . ne_n1 ne_n2 ... ne_npne 80 1 ne ne chars int ints ints

np1+np2+...+npne ints

Ascii form of element block, if nsided:

nsided ne [id_n1 id_n2 . id_ne] np1 np2 . npne e1_n1 e1_n2 ... e1_np1 e2_n1 e2_n2 ... e2_np2 . ne_n1 ne_n2 ... ne_npne A I10 I10 1/line (ne)

This data is needed . . .

I10

1/line (ne)

I10 np*/line (ne lines)

11-12

EnSight 7 User Manual

11.1 EnSight Gold Geometry File Format

EnSight Gold The following is an example of an ASCII EnSight Gold geometry file: This is the Geometry File Example same example model as given in the EnSight6 geometry file section (only in Gold format) with 11 defined unstructured nodes from which 2 unstructured parts are defined, and a 2x3x2 structured part as depicted in the above diagram. Note: The example file below (engold.geo) and all example variable files in the gold section (also prefixed with engold) may be found under your EnSight installation directory (path: $ENSIGHT7_HOME/data/user_manual). The appended # comment lines are for your reference only, and are not valid format lines within a geometry file as appended below. Do NOT put these # comments in your file!!!

Note:

This is the 1st description line of the EnSight Gold geometry example This is the 2nd description line of the EnSight Gold geometry example node id given element id given extents 0.00000e+00 2.00000e+00 0.00000e+00 2.00000e+00 0.00000e+00 2.00000e+00 part 1 2D uns-elements (description line for part 1) coordinates Do NOT put these # comments in your file!! 10 # nn 15 # node ids 20 40 22 44 55 60 61 62 63 4.00000e+00 # x components 5.00000e+00 6.00000e+00

EnSight 7 User Manual

11-13

11.1 EnSight Gold Geometry File Format

5.00000e+00 6.00000e+00 6.00000e+00 5.00000e+00 6.00000e+00 6.00000e+00 5.00000e+00 0.00000e+00 0.00000e+00 0.00000e+00 1.00000e+00 1.00000e+00 3.00000e+00 0.00000e+00 0.00000e+00 1.00000e+00 1.00000e+00 0.00000e+00 0.00000e+00 0.00000e+00 0.00000e+00 0.00000e+00 0.00000e+00 2.00000e+00 2.00000e+00 2.00000e+00 2.00000e+00 tria3 2 102 103 1 4 hexa8 1 104 2 part 2 1D uns-elements (description line for part 2) coordinates 2 15 31 4.00000e+00 3.00000e+00 0.00000e+00 0.00000e+00 0.00000e+00 0.00000e+00 bar2 1 101 2 1 part 3 3D struct-part (description line fro part 3) block iblanked 2 3 2 0.00000e+00 # i components 2.00000e+00 0.00000e+00 2.00000e+00 0.00000e+00 2.00000e+00 0.00000e+00 2.00000e+00

# y components

# z components

# element type # ne # element ids 2 5 4 6

10

11-14

EnSight 7 User Manual

11.1 EnSight Gold Geometry File Format

0.00000e+00 2.00000e+00 0.00000e+00 2.00000e+00 0.00000e+00 0.00000e+00 1.00000e+00 1.00000e+00 3.00000e+00 3.00000e+00 0.00000e+00 0.00000e+00 1.00000e+00 1.00000e+00 3.00000e+00 3.00000e+00 0.00000e+00 0.00000e+00 0.00000e+00 0.00000e+00 0.00000e+00 0.00000e+00 2.00000e+00 2.00000e+00 2.00000e+00 2.00000e+00 2.00000e+00 2.00000e+00 1 1 1 1 1 1 1 1 1 1 1 1

# j components

# k components

# iblanking

EnSight 7 User Manual

11-15

11.1 EnSight Gold Case File Format

EnSight Gold Case File Format

The Case file is an ASCII free format file that contains all the file and name information for accessing model (and measured) geometry, variable, and time information. It is comprised of five sections (FORMAT, GEOMETRY, VARIABLE, TIME, FILE) as described below: Notes: All lines in the Case file are limited to 79 characters. The titles of each section must be in all capital letters. Anything preceded by a # denotes a comment and is ignored. Comments may append information lines or be placed on their own lines. Information following : may be separated by white spaces or tabs. Specifications encased in [] are optional, as indicated. Format Section This is a required section which specifies the type of data to be read. Usage:
FORMAT type: ensight gold

Geometry Section

This is a required section which specifies the geometry information for the model (as well as measured geometry if present, and periodic match file (see Section 11.9, Periodic Matchfile Format) if present). Usage:
GEOMETRY model: measured: match: [ts] [ts] [fs] [fs] filename filename filename [change_coords_only] [change_coords_only]

where: ts = time set number as specified in TIME section. This is optional. fs = corresponding file set number as specified in FILE section below. filename = The filename of the appropriate file. -> Model or measured filenames for a static geometry case, and match filenames will not contain * wildcards. -> Model or measured filenames for a changing geometry case will contain * wildcards. change_coords_only = The option to indicate that the changing geometry (as indicated by wildcards in the filename) is coords only. Otherwise, changing geometry connectivity will be assumed.

Variable Section

This is an optional section which specifies the files and names of the variables. Constant variable values can also be set in this section. Usage:
VARIABLE constant per case: scalar per node: vector per node: tensor symm per node: scalar per element: vector per element: tensor symm per element: scalar per measured node: vector per measured node: complex scalar per node: complex vector per node: [ts] [ts] [ts] [ts] [ts] [ts] [ts] [ts] [ts] [ts] [ts] description description description description description description description description description description description const_value(s) filename filename filename filename filename filename filename filename Re_fn Im_fn Re_fn Im_fn

[fs] [fs] [fs] [fs] [fs] [fs] [fs] [fs] [fs] [fs]

freq freq

11-16

EnSight 7 User Manual

11.1 EnSight Gold Case File Format

complex scalar per element: complex vector per element:

[ts] [fs] description Re_fn [ts] [fs] description Re_fn

Im_fn Im_fn

freq freq

where:

ts

fs description const_value(s) filename Re_fn Im_fn freq

= The corresponding time set number (or index) as specified in TIME section below. This is only required for transient constants and variables. = The corresponding file set number (or index) as specified in FILE section below. = The variable (GUI) name (ex. Pressure, Velocity, etc.) = The constant value. If constants change over time, then ns (see TIME section below) constant values of ts. = The filename of the variable file. Note: only transient filenames contain * wildcards. = The filename for the file containing the real values of the complex variable. = The filename for the file containing the imaginary values of the complex variable. = The corresponding harmonic frequency of the complex variable. For complex variables where harmonic frequency is undefined, simply use the text string: UNDEFINED.

Note: Note:

As many variable description lines as needed may be used. The variable description is limited to 19 characters in the current release. Variable names must not start with a numeric digit and must not contain any of the following reserved characters: ( ) [ ] + @ space ! # * ^ $ /

Time Section

This is an optional section for steady state cases, but is required for transient cases. It contains time set information. Shown below is information for one time set. Multiple time sets (up to 16) may be specified for measured data as shown in Case File Example 3 below. Usage:
TIME time set: ts [description] number of steps: ns filename start number: fs filename increment: fi time values: time_1 time_2 .... time_ns

or
TIME time set: number of steps: filename numbers: time values:

ts [description] ns fn time_1 time_2 .... time_ns

where: ts = timeset number. This is the number referenced in the GEOMETRY and VARIABLE sections. description = optional timeset description which will be shown in user interface. ns = number of transient steps fs = the number to replace the * wildcards in the filenames, for the first step

EnSight 7 User Manual

11-17

11.1 EnSight Gold Case File Format fi = the increment to fs for subsequent steps time = the actual time values for each step, each of which must be separated

by a white space and which may continue on the next line if needed
fn = a list of numbers or indices, to replace the * wildcards in the filenames.

File Section

This section is optional for expressing a transient case with single-file formats. This section contains single-file set information. This information specifies the number of time steps in each file of each data entity, i.e. each geometry and each variable (model and/or measured). Each data entitys corresponding file set might have multiple continuation files due to system file size limit, i.e. ~2 GB for 32-bit and ~4 TB for 64-bit architectures. Each file set corresponds to one and only one time set, but a time set may be referenced by many file sets. The following information may be specified in each file set. For file sets where all of the time set data exceeds the maximum file size limit of the system, both filename index and number of steps are repeated within the file set definition for each continuation file required. Otherwise filename index may be omitted if there is only one file. File set information is shown in Case File Example 4 below.

Usage:
FILE file set: filename index: number of steps: fs fi # Note: only used when data continues in other files ns

where: fs = file set number. This is the number referenced in the GEOMETRY and VARIABLE sections above. ns = number of transient steps fi = file index number in the file name (replaces * in the filenames) Case File Example 1 The following is a minimal EnSight Gold case file for a steady state model with some results.
Note: this (engold.case) file, as well as all of its referenced geometry and variable files (along with a couple of command files) can be found under your installation directory (path: $ENSIGHT7_HOME/data/user_manual). The EnSight Gold Geometry File Example and the Variable File Examples are the contents of these files.
FORMAT type: ensight gold GEOMETRY model: engold.geo VARIABLE constant per case: scalar per element: scalar per node: vector per element: vector per node: tensor symm per element: tensor symm per node: complex scalar per element: complex scalar per node: Cden Esca Nsca Evec Nvec Eten Nten Ecmp Ncmp .8 engold.Esca engold.Nsca engold.Evec engold.Nvec engold.Eten engold.Nten engold.Ecmp_rengold.Ecmp_i2. engold.Ncmp_rengold.Ncmp_i4.

11-18

EnSight 7 User Manual

11.1 EnSight Gold Case File Format

Case File Example 2

The following is a Case file for a transient model. The connectivity of the geometry is also changing.
FORMAT type: ensight gold GEOMETRY model: VARIABLE scalar per node: vector per node: TIME time set: number of steps: filename start number: filename increment: time values: 1.0

exgold2.geo**

1 1

Stress Displacement

exgold2.scl** exgold2.dis**

2.0

1 3 0 1 3.0

The following files would be needed for Example 2:

exgold2.geo00 exgold2.geo01 exgold2.geo02 exgold2.scl00 exgold2.scl01 exgold2.scl02 exgold2.dis00 exgold2.dis01 exgold2.dis02

Case File Example 3

The following is a Case file for a transient model with measured data.

This example has pressure given per element.

FORMAT type: ensight gold

GEOMETRY model: measured:

1 2

exgold3.geo* exgold3.mgeo**

VARIABLE constant per case: constant per case: scalar per element vector per node: scalar per measured node: vector per measured node: TIME time set: number of steps: filename start number: filename increment: time values: time set: number of steps: filename start number: filename increment: time values: .05 .15 .25 .34 .45 .55

1 1 1 2 2

Gamma 1.4 Density .9 .9 Pressure Velocity Temperature Velocity

.7 .6 .6 exgold3.pre* exgold3.vel* exgold3.mtem** exgold3.mvel**

1 5 1 2 .1 .2 .3 .4 .5 2 6 0 2

# This example shows that time # values can be on multiple lines

EnSight 7 User Manual

11-19

11.1 EnSight Gold Case File Format

The following files would be needed for Example 3:

exgold3.geo1 exgold3.geo3 exgold3.geo5 exgold3.geo7 exgold3.geo9 exgold3.mgeo00 exgold3.mgeo02 exgold3.mgeo04 exgold3.mgeo06 exgold3.mgeo08 exgold3.mgeo10 exgold3.pre1 exgold3.pre3 exgold3.pre5 exgold3.pre7 exgold3.pre9 exgold3.mtem00 exgold3.mtem02 exgold3.mtem04 exgold3.mtem06 exgold3.mtem08 exgold3.mtem10 exgold3.vel1 exgold3.vel3 exgold3.vel5 exgold3.vel7 exgold3.vel9 exgold3.mvel00 exgold3.mvel02 exgold3.mvel04 exgold3.mvel06 exgold3.mvel08 exgold3.mvel10

Case File Example 4

The following is Case File Example 3 expressed in transient single-file formats.

In this example, the transient data for the measured velocity data entity happens to be greater than the maximum file size limit. Therefore, the first four time steps fit and are contained in the first file, and the last two time steps are continued in a second file.
FORMAT type: ensight gold GEOMETRY model: measured: VARIABLE constant per case: scalar per element: vector per node: scalar per measured node: vector per measured node: TIME time set: number of steps: time values: time set: number of steps: time values: FILE file set: number of steps: file set: number of steps: file set: filename index: number of steps: filename index: number of steps:

1 2

exgold4.geo 1 exgold4.mgeo 2

1 1 2 2

1 1 2 3

Density Pressure Velocity Temperature Velocity

.5 exgold4.pre exgold4.vel exgold4.mtem exgold4.mvel*

1 Model 5 .1 .2 .3 .4 .5 2 Measured 6 .05 .15 .25 .34 .45 .55

1 5 2 6 3 1 4 2 2

11-20

EnSight 7 User Manual

11.1 EnSight Gold Case File Format

The following files would be needed for Example 4:

exgold4.geo exgold4.mgeoe exgold4.pre exgold4.mtem exgold4.vel exgold4.mvel1 exgold4.mvel2

Contents of Transient Single Files

Each file contains transient data that corresponds to the specified number of time steps. The data for each time step sequentially corresponds to the simulation time values (time values) found listed in the TIME section. In transient single-file format, the data for each time step essentially corresponds to a standard EnSight gold geometry or variable file (model or measured) as expressed in multiple file format. The data for each time step is enclosed between two wrapper records, i.e. preceded by a BEGIN TIME STEP record and followed by an END TIME STEP record. Time step data is not split between files. If there is not enough room to append the data from a time step to the file without exceeding the maximum file limit of a particular system, then a continuation file must be created for the time step data and any subsequent time step. Any type of user comments may be included before and/or after each transient step wrapper.

Note 1: If transient single file format is used, EnSight expects all files of a dataset to be specified in transient single file format. Thus, even static files must be enclosed between a BEGIN TIME STEP and an END TIME STEP wrapper. 1. Note 2: For binary geometry files, the first BEGIN TIME STEP wrapper must follow the <C Binary/Fortran Binary> line. Both BEGIN TIME STEP and END TIME STEP wrappers are written according to type (1) in binary. Namely: This is a write of 80 characters to the file: in C: char buffer[80];
strcpy(buffer,BEGIN TIME STEP); fwrite(buffer,sizeof(char),80,file_ptr);

in FORTRAN: character*80 buffer

buffer = BEGIN TIME STEP

Note 3: Efficient reading of each file (especially binary) is facilitated by appending each file with a file index. A file index contains appropriate information to access the file byte positions of each time step in the file. (EnSight automatically appends a file index to each file when exporting in transient single file format.) If used, the file index must follow the last END TIME STEP wrapper in each file.
File Index Usage: ASCII
%20d\n %20d\n %20d\n ... %20d\n %20d\n %20d\n %s\n
*

Binary
sizeof(int) sizeof(long) sizeof(long) ... sizeof(long) sizeof(int) sizeof(long) sizeof(char)*80

Item
n fb1 fb2 ... fbn flag fb of item n
FILE_INDEX

Description
Total number of data time steps in the file. File byte loc for contents of 1st time step* File byte loc for contents of 2nd time step* ... File byte loc for contents of nth time step* Miscellaneous flag (= 0 for now) File byte loc for Item n above File index keyword

Each file byte location is the first byte that follows the BEGIN TIME STEP record.

Shown below are the contents of each of the above files, using the data files from Case File Example 3 for reference (without FILE_INDEX for simplicity).
Contents of file exgold4.geo_1:

EnSight 7 User Manual

11-21

11.1 EnSight Gold Case File Format

BEGIN TIME STEP Contents of file exgold3.geo1 END TIME STEP BEGIN TIME STEP Contents of file exgold3.geo3 END TIME STEP BEGIN TIME STEP Contents of file exgold3.geo5 END TIME STEP BEGIN TIME STEP Contents of file exgold3.geo7 END TIME STEP BEGIN TIME STEP Contents of file exgold3.geo9 END TIME STEP

Contents of file exgold4.pre_1:

BEGIN TIME STEP Contents of file exgold3.pre1 END TIME STEP BEGIN TIME STEP Contents of file exgold3.pre3 END TIME STEP BEGIN TIME STEP Contents of file exgold3.pre5 END TIME STEP BEGIN TIME STEP Contents of file exgold3.pre7 END TIME STEP BEGIN TIME STEP Contents of file exgold3.pre9 END TIME STEP

Contents of file exgold4.vel_1:

BEGIN TIME STEP Contents of file exgold3.vel1 END TIME STEP BEGIN TIME STEP Contents of file exgold3.vel3 END TIME STEP BEGIN TIME STEP Contents of file exgold3.vel5 END TIME STEP BEGIN TIME STEP Contents of file exgold3.vel7 END TIME STEP BEGIN TIME STEP Contents of file exgold3.vel9 END TIME STEP

Contents of file exgold4.mgeo_1:

BEGIN TIME STEP Contents of file exgold3.mgeo00 END TIME STEP BEGIN TIME STEP Contents of file exgold3.mgeo02 END TIME STEP BEGIN TIME STEP Contents of file exgold3.mgeo04 END TIME STEP BEGIN TIME STEP Contents of file exgold3.mgeo06 END TIME STEP BEGIN TIME STEP Contents of file exgold3.mgeo08 END TIME STEP BEGIN TIME STEP Contents of file exgold3.mgeo10 END TIME STEP

Contents of file exgold4.mtem_1:

BEGIN TIME STEP Contents of file exgold3.mtem00 END TIME STEP BEGIN TIME STEP Contents of file exgold3.mtem02 END TIME STEP BEGIN TIME STEP Contents of file exgold3.mtem04 END TIME STEP BEGIN TIME STEP Contents of file exgold3.mtem06 END TIME STEP BEGIN TIME STEP Contents of file exgold3.mtem08 END TIME STEP

11-22

EnSight 7 User Manual

11.1 EnSight Gold Variable File Format

BEGIN TIME STEP Contents of file exgold3.mtem10 END TIME STEP

Contents of file exgold4.mvel1_1:

BEGIN TIME STEP Contents of file exgold3.mvel00 END TIME STEP BEGIN TIME STEP Contents of file exgold3.mvel02 END TIME STEP BEGIN TIME STEP Contents of file exgold3.mvel04 END TIME STEP BEGIN TIME STEP Contents of file exgold3.mvel06 END TIME STEP

Contents of file exgold4.mvel2_1:

Comments can precede the beginning wrapper here.

BEGIN TIME STEP Contents of file exgold3.mvel08 END TIME STEP Comments can go between time step wrappers here. BEGIN TIME STEP Contents of file exgold3.mvel10 END TIME STEP

Comments can follow the ending time step wrapper.

EnSight Gold Wild Card Name Specification

If multiple time steps are involved, the file names must conform to the EnSight wild-card specification. This specification is as follows: File names must include numbers that are in ascending order from beginning to end. Numbers in the files names must be zero filled if there is more than one significant digit. Numbers can be anywhere in the file name. When the file name is specified in the EnSight case file, you must replace the numbers in the file with an asterisk(*). The number of asterisks specified is the number of significant digits. The asterisk must occupy the same place as the numbers in the file names.

EnSight Gold Variable File Format

EnSight Gold variable files can either be per_node or per_element. They cannot be both. However, an EnSight model can have some variables which are per_node and others which are per_element.

EnSight Gold Per_Node Variable File Format

EnSight Gold variable files for per_node variables contain values for each unstructured node and for each structured node. First comes a single description line. Second comes a part line. Third comes a line containing the part number. Fourth comes a coordinates line or a block line. If a coordinates line, the value for each unstructured node of the part follows. If it is a scalar file, there is one value per node, while for vector files there are three values per node (output in the same component order as the coordinates, namely, all x components, then all y components, then all z components). If it is a block line, the value(s) for each
EnSight 7 User Manual 11-23

11.1 EnSight Gold Per_Node Variable File Format

structured node follows. The values for each node of the structured block are output in the same IJK order as the coordinates. (The number of nodes in the part are obtained from the corresponding EnSight Gold geometry file.) C Binary form:
SCALAR FILE:
description line 1 part # coordinates s_n1 s_n2 ... s_nn part . . part # block s_m1 s_m2 ... s_mm 80 80 1 80 nn 80 chars chars int chars floats chars

# mm = i*j*k

80 1 80 mm

chars int chars floats

VECTOR FILE:
description line 1 part # coordinates vx_n1 vx_n2 ... vx_nn vy_n1 vy_n2 ... vy_nn vz_n1 vz_n2 ... vz_nn part . . part # block vx_m1 vx_m2 ... vx_mm vy_m1 vy_m2 ... vy_mm vz_m1 vz_m2 ... vz_mm 80 80 1 80 nn nn nn 80 chars chars int chars floats floats floats chars

# mm = i*j*k

80 1 80 mm mm mm

chars int chars floats floats floats

TENSOR FILE:
description line 1 part # coordinates v11_n1 v11_n2 ... v11_nn v22_n1 v22_n2 ... v22_nn v33_n1 v33_n2 ... v33_nn v12_n1 v12_n2 ... v12_nn v13_n1 v13_n2 ... v13_nn v23_n1 v23_n2 ... v23_nn part . . part # block # mm = i*j*k v11_m1 v11_m2 ... v11_mm 80 80 1 80 nn nn nn nn nn nn 80 chars chars int chars floats floats floats floats floats floats chars

80 1 80 mm

chars int chars floats

11-24

EnSight 7 User Manual

11.1 EnSight Gold Per_Node Variable File Format v22_m1 v33_m1 v12_m1 v13_m1 v23_m1 v22_m2 v33_m2 v12_m2 v13_m2 v23_m2 ... ... ... ... ... v22_mm v33_mm v12_mm v13_mm v23_mm mm mm mm mm mm floats floats floats floats floats

TENSOR9 FILE:
description line 1 part # coordinates v11_n1 v11_n2 ... v11_nn v12_n1 v12_n2 ... v12_nn v13_n1 v13_n2 ... v13_nn v21_n1 v21_n2 ... v21_nn v22_n1 v22_n2 ... v22_nn v23_n1 v23_n2 ... v23_nn v31_n1 v31_n2 ... v31_nn v32_n1 v32_n2 ... v32_nn v33_n1 v33_n2 ... v33_nn part . . part # block # mm = i*j*k v11_m1 v11_m2 ... v11_mm v12_m1 v12_m2 ... v12_mm v13_m1 v13_m2 ... v13_mm v21_m1 v21_m2 ... v21_mm v22_m1 v22_m2 ... v22_mm v23_m1 v23_m2 ... v23_mm v21_m1 v21_m2 ... v21_mm v22_m1 v22_m2 ... v22_mm v23_m1 v23_m2 ... v23_mm 80 80 1 80 nn nn nn nn nn nn nn nn nn 80 chars chars int chars floats floats floats floats floats floats floats floats floats chars

80 1 80 mm mm mm mm mm mm mm mm mm

chars int chars floats floats floats floats floats floats floats floats floats

COMPLEX SCALAR FILES (Real and/or Imaginary):

description line 1 part # coordinates s_n1 s_n2 ... s_nn part . . part # block s_m1 s_m2 ... s_mm 80 80 1 80 nn 80 chars chars int chars floats chars

# mm = i*j*k

80 1 80 mm

chars int chars floats

COMPLEX VECTOR FILES (Real and/or Imaginary):

description line 1 part # coordinates vx_n1 vx_n2 ... vx_nn vy_n1 vy_n2 ... vy_nn 80 80 1 80 nn nn chars chars int chars floats floats

EnSight 7 User Manual

11-25

11.1 EnSight Gold Per_Node Variable File Format vz_n1 part . . part # block vx_m1 vy_m1 vz_m1 vz_n2 ... vz_nn nn floats 80 chars

# mm = i*j*k vx_m2 ... vx_mm vy_m2 ... vy_mm vz_m2 ... vz_mm

80 1 80 mm mm mm

chars int chars floats floats floats

Fortran Binary form:

SCALAR FILE:
description line 1 part # coordinates s_n1 s_n2 ... s_nn part . . part # block s_m1 s_m2 ... s_mm 80 80 1 80 nn 80 chars chars int chars floats chars

# mm = i*j*k

80 1 80 mm

chars int chars floats

VECTOR FILE:
description line 1 part # coordinates vx_n1 vx_n2 ... vx_nn vy_n1 vy_n2 ... vy_nn vz_n1 vz_n2 ... vz_nn part . . part # block vx_m1 vx_m2 ... vx_mm vy_m1 vy_m2 ... vy_mm vz_m1 vz_m2 ... vz_mm 80 80 1 80 nn nn nn 80 chars chars int chars floats floats floats chars

# mm = i*j*k

80 1 80 mm mm mm

chars int chars floats floats floats

TENSOR FILE:
description line 1 part # coordinates v11_n1 v11_n2 ... v11_nn v22_n1 v22_n2 ... v22_nn v33_n1 v33_n2 ... v33_nn v12_n1 v12_n2 ... v12_nn 80 80 1 80 nn nn nn nn chars chars int chars floats floats floats floats

11-26

EnSight 7 User Manual

11.1 EnSight Gold Per_Node Variable File Format v13_n1 v23_n1 part . . part # block v11_m1 v22_m1 v33_m1 v12_m1 v13_m1 v23_m1 v13_n2 ... v13_nn v23_n2 ... v23_nn nn floats nn floats 80 chars

# mm = i*j*k v11_m2 v22_m2 v33_m2 v12_m2 v13_m2 v23_m2 ... ... ... ... ... ... v11_mm v22_mm v33_mm v12_mm v13_mm v23_mm

80 1 80 mm mm mm mm mm mm

chars int chars floats floats floats floats floats floats

TENSOR9 FILE:
description line 1 part # coordinates v11_n1 v11_n2 ... v11_nn v12_n1 v12_n2 ... v12_nn v13_n1 v13_n2 ... v13_nn v21_n1 v21_n2 ... v21_nn v22_n1 v22_n2 ... v22_nn v23_n1 v23_n2 ... v23_nn v31_n1 v31_n2 ... v31_nn v32_n1 v32_n2 ... v32_nn v33_n1 v33_n2 ... v33_nn part . . part # block # mm = i*j*k v11_m1 v11_m2 ... v11_mm v12_m1 v12_m2 ... v12_mm v13_m1 v13_m2 ... v13_mm v21_m1 v21_m2 ... v21_mm v22_m1 v22_m2 ... v22_mm v23_m1 v23_m2 ... v23_mm v31_m1 v31_m2 ... v31_mm v32_m1 v32_m2 ... v32_mm v33_m1 v33_m2 ... v33_mm 80 80 1 80 nn nn nn nn nn nn nn nn nn 80 chars chars int chars floats floats floats floats floats floats floats floats floats chars

80 1 80 mm mm mm mm mm mm mm mm mm

chars int chars floats floats floats floats floats floats floats floats floats

COMPLEX SCALAR FILES (Real and/or Imaginary):

description line 1 part # coordinates s_n1 s_n2 ... s_nn part . . part # block s_m1 s_m2 ... s_mm 80 80 1 80 nn 80 chars chars int chars floats chars

# mm = i*j*k

80 1 80 mm

chars int chars floats

EnSight 7 User Manual

11-27

11.1 EnSight Gold Per_Node Variable File Format

COMPLEX VECTOR FILES (Real and/or Imaginary):

description line 1 part # coordinates vx_n1 vx_n2 ... vx_nn vy_n1 vy_n2 ... vy_nn vz_n1 vz_n2 ... vz_nn part . . part # block vx_m1 vx_m2 ... vx_mm vy_m1 vy_m2 ... vy_mm vz_m1 vz_m2 ... vz_mm 80 80 1 80 nn nn nn 80 chars chars int chars floats floats floats chars

# mm = i*j*k

80 1 80 mm mm mm

chars int chars floats floats floats

ASCII form:
SCALAR FILE:
description line 1 part # coordinates s_n1 s_n2 . . s_nn part . . part # block s_m1 s_m2 . . s_mm A (max of 79 typ) A I10 A E12.5 1/line (nn)

# mm = i*j*k

A I10 A E12.5 1/line (mm)

VECTOR FILE:
description line 1 part # coordinates vx_n1 vx_n2 . . vx_nn A (max of 79 typ) A I10 A E12.5 1/line (nn)

11-28

EnSight 7 User Manual

11.1 EnSight Gold Per_Node Variable File Format vy_n1 vy_n2 . . vy_nn vz_n1 vz_n2 . . vz_nn part . . part # block vx_m1 vx_m2 . . vx_mm vy_m1 vy_m2 . . vy_mm vz_m1 vz_m2 . . vz_mm E12.5 1/line (nn)

E12.5 1/line (nn)

# mm = i*j*k

A I10 A E12.5 1/line (mm)

E12.5 1/line (mm)

E12.5 1/line (mm)

TENSOR FILE:
description line 1 part # coordinates v11_n1 v11_n2 . . v11_nn v22_n1 v22_n2 . . v22_nn v33_n1 v33_n2 . . v33_nn v12_n1 v12_n2 . . v12_nn v13_n1 v13_n2 . A (max of 79 typ) A I10 A E12.5 1/line (nn)

E12.5 1/line (nn)

E12.5 1/line (nn)

E12.5 1/line (nn)

E12.5 1/line (nn)

EnSight 7 User Manual

11-29

11.1 EnSight Gold Per_Node Variable File Format . v13_nn v23_n1 v23_n2 . . v23_nn part . . part # block v11_m1 v11_m2 . . v11_mm v22_m1 v22_m2 . . v22_mm v33_m1 v33_m2 . . v33_mm v12_m1 v12_m2 . . v12_mm v13_m1 v13_m2 . . v13_mm v23_m1 v23_m2 . . v23_mm

E12.5 1/line (nn)

# mm = i*j*k

A I10 A E12.5 1/line (mm)

E12.5 1/line (mm)

E12.5 1/line (mm)

E12.5 1/line (mm)

E12.5 1/line (mm)

E12.5 1/line (mm)

TENSOR9 FILE:
description line 1 part # coordinates v11_n1 v11_n2 . . v11_nn v12_n1 v12_n2 . . v12_nn v13_n1 A (max of 79 typ) A I10 A E12.5 1/line (nn)

E12.5 1/line (nn)

E12.5 1/line (nn)

11-30

EnSight 7 User Manual

11.1 EnSight Gold Per_Node Variable File Format v13_n2 . . v13_nn v21_n1 v21_n2 . . v21_nn v22_n1 v22_n2 . . v22_nn v23_n1 v23_n2 . . v23_nn v31_n1 v31_n2 . . v31_nn v32_n1 v32_n2 . . v32_nn v33_n1 v33_n2 . . v33_nn part . . part # block v11_m1 v11_m2 . . v11_mm v12_m1 v12_m2 . . v12_mm v13_m1 v13_m2 . . v13_mm v21_m1 v21_m2 . . v21_mm v22_m1

E12.5 1/line (nn)

E12.5 1/line (nn)

E12.5 1/line (nn)

E12.5 1/line (nn)

E12.5 1/line (nn)

E12.5 1/line (nn)

# mm = i*j*k

A I10 A E12.5 1/line (mm)

E12.5 1/line (mm)

E12.5 1/line (mm)

E12.5 1/line (mm)

E12.5 1/line (mm)

EnSight 7 User Manual

11-31

11.1 EnSight Gold Per_Node Variable File Format v22_m2 . . v22_mm v23_m1 v23_m2 . . v23_mm v31_m1 v31_m2 . . v31_mm v32_m1 v32_m2 . . v32_mm v33_m1 v33_m2 . . v33_mm

E12.5 1/line (mm)

E12.5 1/line (mm)

E12.5 1/line (mm)

E12.5 1/line (mm)

COMPLEX SCALAR FILES (Real and/or Imaginary):

description line 1 part # coordinates s_n1 s_n2 . . s_nn part . . part # block s_m1 s_m2 . . s_mm A (max of 79 typ) A I10 A E12.5 1/line (nn)

# mm = i*j*k

A I10 A E12.5 1/line (mm)

COMPLEX VECTOR FILES (Real and/or Imaginary):

description line 1 part # coordinates vx_n1 vx_n2 . . A (max of 79 typ) A I10 A E12.5 1/line (nn)

11-32

EnSight 7 User Manual

11.1 EnSight Gold Per_Node Variable File Format vx_nn vy_n1 vy_n2 . . vy_nn vz_n1 vz_n2 . . vz_nn part . . part # block vx_m1 vx_m2 . . vx_mm vy_m1 vy_m2 . . vy_mm vz_m1 vz_m2 . . vz_mm

E12.5 1/line (nn)

E12.5 1/line (nn)

# mm = i*j*k

A I10 A E12.5 1/line (mm)

E12.5 1/line (mm)

E12.5 1/line (mm)

EnSight 7 User Manual

11-33

11.1 EnSight Gold Per_Node Variable File Format

The following variable file examples reflect scalar, vector, tensor, and complex variable values per node for the previously defined EnSight6 Gold Geometry File Example with 11 defined unstructured nodes and a 2x3x2 structured Part (Part number 3). The values are summarized in the following table. Note:
These are the same values as listed in the EnSight6 per_node variable file section. Subsequently, the following example files contain the same data as the example files given in the EnSight6 section only they are listed in gold format. (No asymmetric tensor example data given) ComplexScalar Node Node Scalar Vector Index Id
Unstructured 1 2 3 4 5 6 7 8 9 10 11 Structured 1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9 10 11 12 (1.) (2.) (3.) (4.) (5.) (6.) (7.) (8.) (9.) (10.) (11.) (12.) (1.1, 1.2, 1.3) (2.1, 2.2, 2.3) (3.1, 3.2, 3.3) (4.1, 4.2, 4.3) (5.1, 5.2, 5.3) (6.1, 6.2, 6.3) (7.1, 7.2, 7.3) (8.1, 8.2, 8.3) (9.1, 9.2, 9.3) (10.1,10.2,10.3) (11.1,11.2,11.3) (12.1,12.2,12.3) (1.1, 1.2, 1.3, 1.4, 1.5, 1.6) (2.1, 2.2, 2.3, 2.4, 2.5, 2.6) (3.1, 3.2, 3.3, 3.4, 3.5, 3.6) (4.1, 4.2, 4.3, 4.4, 4.5, 4.6) (5.1, 5.2, 5.3, 5.4, 5.5, 5.6) (6.1, 6.2, 6.3, 6.4, 6.5, 6.6) (7.1, 7.2, 7.3, 7.4, 7.5, 7.6) (8.1, 8.2, 8.3, 8.4, 8.5, 8.6) (9.1, 9.2, 9.3, 9.4, 9.5, 9.6) (10.1,10.2,10.3,10.4,10.5,10.6) (11.1,11.2,11.3,11.4,11.5,11.6) (12.1,12.2,12.3,12.4,12.5,12.6) (1.1) (2.1) (3.1) (4.1) (5.1) (6.1) (7.1) (8.1) (9.1) (10.1) (11.1) (12.1) (1.2) (2.2) (3.2) (4.2) (5.2) (6.2) (7.2) (8.2) (9.2) (10.2) (11.2) (12.2) 15 31 20 40 22 44 55 60 61 62 63 (1.) (2.) (3.) (4.) (5.) (6.) (7.) (8.) (9.) (10.) (11.) (1.1, 1.2, 1.3) (2.1, 2.2, 2.3) (3.1, 3.2, 3.3) (4.1, 4.2, 4.3) (5.1, 5.2, 5.3) (6.1, 6.2, 6.3) (7.1, 7.2, 7.3) (8.1, 8.2, 8.3) (9.1, 9.2, 9.3) (10.1,10.2,10.3) (11.1,11.2,11.3) (1.1, 1.2, 1.3, 1.4, 1.5, 1.6) (2.1, 2.2, 2.3, 2.4, 2.5, 2.6) (3.1, 3.2, 3.3, 3.4, 3.5, 3.6) (4.1, 4.2, 4.3, 4.4, 4.5, 4.6) (5.1, 5.2, 5.3, 5.4, 5.5, 5.6) (6.1, 6.2, 6.3, 6.4, 6.5, 6.6) (7.1, 7.2, 7.3, 7.4, 7.5, 7.6) (8.1, 8.2, 8.3, 8.4, 8.5, 8.60 (9.1, 9.2, 9.3, 9.4, 9.5, 9.6) (10.1,10.2,10.3,10.4,10.5,10.6) (11.1,11.2,11.3,11.4,11.5,11.6) (1.1) (2.1) (3.1) (4.1) (5.1) (6.1) (7.1) (8.1) (9.1) (10.1) (11.1) (1.2) (2.2) (3.2) (4.2) (5.2) (6.2) (7.2) (8.2) (9.2) (10.2) (11.2)

Tensor (2nd order symm.) Values

Real

Imaginary

Value

Values

Value Value

Per_node (Scalar) Variable Example 1: This shows an ASCII scalar file (engold.Nsca) for the gold geometry example.
Per_node scalar values for the EnSight Gold geometry example part 1 coordinates 1.00000E+00 3.00000E+00 4.00000E+00 5.00000E+00 6.00000E+00 7.00000E+00 8.00000E+00 9.00000E+00 1.00000E+01 1.10000E+01 part 2 coordinates 1.00000E+00 2.00000E+00

11-34

EnSight 7 User Manual

11.1 EnSight Gold Per_Node Variable File Format

part 3 block 1.00000E+00 2.00000E+00 3.00000E+00 4.00000E+00 5.00000E+00 6.00000E+00 7.00000E+00 8.00000E+00 9.00000E+00 1.00000E+01 1.10000E+01 1.20000E+01

Per_node (Vector) Variable Example 2: This example shows an ASCII vector file (engold.Nvec) for the gold geometry example.
Per_node vector values for the EnSight Gold geometry example part 1 coordinates 1.10000E+00 3.10000E+00 4.10000E+00 5.10000E+00 6.10000E+00 7.10000E+00 8.10000E+00 9.10000E+00 1.01000E+01 1.11000E+01 1.20000E+00 3.20000E+00 4.20000E+00 5.20000E+00 6.20000E+00 7.20000E+00 8.20000E+00 9.20000E+00 1.02000E+01 1.12000E+01 1.30000E+00 3.30000E+00 4.30000E+00 5.30000E+00 6.30000E+00 7.30000E+00 8.30000E+00 9.30000E+00 1.03000E+01 1.13000E+01 part 2 coordinates 1.10000E+00 2.10000E+00 1.20000E+00 2.20000E+00 1.30000E+00 2.30000E+00 part 3 block 1.10000E+00

EnSight 7 User Manual

11-35

11.1 EnSight Gold Per_Node Variable File Format

2.10000E+00 3.10000E+00 4.10000E+00 5.10000E+00 6.10000E+00 7.10000E+00 8.10000E+00 9.10000E+00 1.01000E+01 1.11000E+01 1.21000E+01 1.20000E+00 2.20000E+00 3.20000E+00 4.20000E+00 5.20000E+00 6.20000E+00 7.20000E+00 8.20000E+00 9.20000E+00 1.02000E+01 1.12000E+01 1.22000E+01 1.30000E+00 2.30000E+00 3.30000E+00 4.30000E+00 5.30000E+00 6.30000E+00 7.30000E+00 8.30000E+00 9.30000E+00 1.03000E+01 1.13000E+01 1.23000E+01

Per_node (Tensor) Variable Example 3: This example shows an ASCII 2nd order symmetric tensor file (engold.Nten) for the gold geometry example.
Per_node symmetric tensor values for the EnSight Gold geometry example part 1 coordinates 1.10000E+00 3.10000E+00 4.10000E+00 5.10000E+00 6.10000E+00 7.10000E+00 8.10000E+00 9.10000E+00 1.01000E+01 1.11000E+01 1.20000E+00 3.20000E+00 4.20000E+00 5.20000E+00 6.20000E+00 7.20000E+00 8.20000E+00 9.20000E+00 1.02000E+01 1.12000E+01 1.30000E+00 3.30000E+00 4.30000E+00

11-36

EnSight 7 User Manual

11.1 EnSight Gold Per_Node Variable File Format

5.30000E+00 6.30000E+00 7.30000E+00 8.30000E+00 9.30000E+00 1.03000E+01 1.13000E+01 1.40000E+00 3.40000E+00 4.40000E+00 5.40000E+00 6.40000E+00 7.40000E+00 8.40000E+00 9.40000E+00 1.04000E+01 1.14000E+01 1.50000E+00 3.50000E+00 4.50000E+00 5.50000E+00 6.50000E+00 7.50000E+00 8.50000E+00 9.50000E+00 1.05000E+01 1.15000E+01 1.60000E+00 3.60000E+00 4.60000E+00 5.60000E+00 6.60000E+00 7.60000E+00 8.60000E+00 9.60000E+00 1.06000E+01 1.16000E+01 part 2 coordinates 1.10000E+00 2.10000E+00 1.20000E+00 2.20000E+00 1.30000E+00 2.30000E+00 1.40000E+00 2.40000E+00 1.50000E+00 2.50000E+00 1.60000E+00 2.60000E+00 part 3 block 1.10000E+00 2.10000E+00 3.10000E+00 4.10000E+00 5.10000E+00 6.10000E+00 7.10000E+00 8.10000E+00 9.10000E+00 1.01000E+01 1.11000E+01 1.21000E+01

EnSight 7 User Manual

11-37

11.1 EnSight Gold Per_Node Variable File Format

1.20000E+00 2.20000E+00 3.20000E+00 4.20000E+00 5.20000E+00 6.20000E+00 7.20000E+00 8.20000E+00 9.20000E+00 1.02000E+01 1.12000E+01 1.22000E+01 1.30000E+00 2.30000E+00 3.30000E+00 4.30000E+00 5.30000E+00 6.30000E+00 7.30000E+00 8.30000E+00 9.30000E+00 1.03000E+01 1.13000E+01 1.23000E+01 1.40000E+00 2.40000E+00 3.40000E+00 4.40000E+00 5.40000E+00 6.40000E+00 7.40000E+00 8.40000E+00 9.40000E+00 1.04000E+01 1.14000E+01 1.24000E+01 1.50000E+00 2.50000E+00 3.50000E+00 4.50000E+00 5.50000E+00 6.50000E+00 7.50000E+00 8.50000E+00 9.50000E+00 1.05000E+01 1.15000E+01 1.25000E+01 1.60000E+00 2.60000E+00 3.60000E+00 4.60000E+00 5.60000E+00 6.60000E+00 7.60000E+00 8.60000E+00 9.60000E+00 1.06000E+01 1.16000E+01 1.26000E+01

11-38

EnSight 7 User Manual

11.1 EnSight Gold Per_Node Variable File Format

Per_node (Complex) Variable Example 4: This example shows ASCII complex real (engold.Ncmp_r) and imaginary (engold.Ncmp_i) scalar files for the gold geometry example. (The same methodology would apply for complex real and imaginary vector files.)
Real scalar File:
Per_node complex real scalar values for the EnSight Gold geometry example part 1 coordinates 1.10000E+00 3.10000E+00 4.10000E+00 5.10000E+00 6.10000E+00 7.10000E+00 8.10000E+00 9.10000E+00 1.01000E+01 1.11000E+01 part 2 coordinates 1.10000E+00 2.10000E+00 part 3 block 1.10000E+00 2.10000E+00 3.10000E+00 4.10000E+00 5.10000E+00 6.10000E+00 7.10000E+00 8.10000E+00 9.10000E+00 1.01000E+01 1.11000E+01 1.21000E+01

Imaginary scalar File: Per_node complex imaginary scalar values for the EnSight Gold geometry example part 1 coordinates 1.20000E+00 3.20000E+00 4.20000E+00 5.20000E+00 6.20000E+00 7.20000E+00 8.20000E+00 9.20000E+00 1.02000E+01 1.12000E+01 part 2 coordinates 1.20000E+00 2.20000E+00 part 3 block

EnSight 7 User Manual

11-39

11.1 EnSight Gold Per_Element Variable File Format 1.20000E+00 2.20000E+00 3.20000E+00 4.20000E+00 5.20000E+00 6.20000E+00 7.20000E+00 8.20000E+00 9.20000E+00 1.02000E+01 1.12000E+01 1.22000E+01

EnSight Gold Per_Element Variable File Format

EnSight Gold variable files for per_element variables contain values for each element of designated types of designated Parts. First comes a single description line. Second comes a Part line. Third comes a line containing the part number. Fourth comes an element type line and then comes the value for each element of that type and part. If it is a scalar variable, there is one value per element, while for vector variables there are three values per element. (The number of elements of the given type are obtained from the corresponding EnSight Gold geometry file.) C Binary form:
SCALAR FILE:
description line 1 part # element type s_e1 s_e2 ... s_ne element type . . part . . part # block s_m1 s_m2 ... s_mm 80 80 1 80 ne 80 chars chars int chars floats chars

80 chars

# mm = (i-1)*(j-1)*(k-1)

80 1 80 mm

chars int chars floats

VECTOR FILE:
description line 1 part # element type vx_e1 vx_e2 ... vx_ne vy_e1 vy_e2 ... vy_ne vz_e1 vz_e2 ... vz_ne element type . . 80 80 1 80 ne ne ne 80 chars chars int chars floats floats floats chars

11-40

EnSight 7 User Manual

11.1 EnSight Gold Per_Element Variable File Format part . . part # block vx_m1 vx_m2 ... vx_mm vy_m1 vy_m2 ... vy_mm vz_m1 vz_m2 ... vz_mm 80 chars

# mm = (i-1)*(j-1)*(k-1)

80 1 80 mm mm mm

chars int chars floats floats floats

TENSOR FILE:
description line 1 part # element type v11_e1 v11_e2 ... v11_ne v22_e1 v22_e2 ... v22_ne v33_e1 v33_e2 ... v33_ne v12_e1 v12_e2 ... v12_ne v13_e1 v13_e2 ... v13_ne v23_e1 v23_e2 ... v23_ne element type . . part . . part # block # mm = (i-1)*(j-1)*(k-1) v11_m1 v11_m2 ... v11_mm v22_m1 v22_m2 ... v22_mm v33_m1 v33_m2 ... v33_mm v12_m1 v12_m2 ... v12_mm v13_m1 v13_m2 ... v13_mm v23_m1 v23_m2 ... v23_mm 80 80 1 80 ne ne ne ne ne ne 80 chars chars int chars floats floats floats floats floats floats chars

80 chars

80 1 80 mm mm mm mm mm mm

chars int chars floats floats floats floats floats floats

TENSOR9 FILE:
description line 1 part # element type v11_e1 v11_e2 ... v11_ne v12_e1 v12_e2 ... v12_ne v13_e1 v13_e2 ... v13_ne v21_e1 v21_e2 ... v21_ne v22_e1 v22_e2 ... v22_ne v23_e1 v23_e2 ... v23_ne v31_e1 v31_e2 ... v31_ne v32_e1 v32_e2 ... v32_ne v33_e1 v33_e2 ... v33_ne element type . . part . . 80 80 1 80 ne ne ne ne ne ne ne ne ne 80 chars chars int chars floats floats floats floats floats floats floats floats floats chars

80 chars

EnSight 7 User Manual

11-41

11.1 EnSight Gold Per_Element Variable File Format part # block v11_m1 v12_m1 v13_m1 v21_m1 v22_m1 v23_m1 v31_m1 v32_m1 v33_m1 80 1 80 mm mm mm mm mm mm mm mm mm chars int chars floats floats floats floats floats floats floats floats floats

# mm = (i-1)*(j-1)*(k-1) v11_m2 v12_m2 v13_m2 v21_m2 v22_m2 v23_m2 v31_m2 v32_m2 v33_m2 ... ... ... ... ... ... ... ... ... v11_mm v12_mm v13_mm v21_mm v22_mm v23_mm v31_mm v32_mm v33_mm

COMPLEX SCALAR FILES (Real and/or Imaginary):

description line 1 part # element type s_e1 s_e2 ... s_ne element type . . part . . part # block s_m1 s_m2 ... s_mm 80 80 1 80 ne 80 chars chars int chars floats chars

80 chars

# mm = (i-1)*(j-1)*(k-1)

80 1 80 mm

chars int chars floats

COMPLEX VECTOR FILES (Real and/or Imaginary):

description line 1 part # element type vx_e1 vx_e2 ... vx_ne vy_e1 vy_e2 ... vy_ne vz_e1 vz_e2 ... vz_ne element type . . part . . part # block vx_m1 vx_m2 ... vx_mm vy_m1 vy_m2 ... vy_mm vz_m1 vz_m2 ... vz_mm 80 80 1 80 ne ne ne 80 chars chars int chars floats floats floats chars

80 chars

# mm = (i-1)*(j-1)*(k-1)

80 1 80 mm mm mm

chars int chars floats floats floats

Fortran Binary form:

SCALAR FILE:
description line 1 part 80 chars 80 chars

11-42

EnSight 7 User Manual

11.1 EnSight Gold Per_Element Variable File Format # element s_e1 s_e2 element . . part . . part # block s_m1 s_m2 1 80 ne 80 int chars floats chars

type ... s_ne type

80 chars

# mm = (i-1)*(j-1)*(k-1) ... s_mm

80 1 80 mm

chars int chars floats

VECTOR FILE:
description line 1 part # element type vx_e1 vx_e2 ... vx_ne vy_e1 vy_e2 ... vy_ne vz_e1 vz_e2 ... vz_ne element type . . part . . part # block # mm = (i-1)*(j-1)*(k-1) vx_m1 vx_m2 ... vx_mm vy_m1 vy_m2 ... vy_mm vz_m1 vz_m2 ... vz_mm 80 80 1 80 ne ne ne 80 chars chars int chars floats floats floats chars

80 chars

80 1 80 mm mm mm

chars int chars floats floats floats

TENSOR FILE:
description line 1 part # element type v11_e1 v11_e2 ... v11_ne v22_e1 v22_e2 ... v22_ne v33_e1 v33_e2 ... v33_ne v12_e1 v12_e2 ... v12_ne v13_e1 v13_e2 ... v13_ne v23_e1 v23_e2 ... v23_ne element type . . part . . part # block # mm = (i-1)*(j-1)*(k-1) v11_m1 v11_m2 ... v11_mm v22_m1 v22_m2 ... v22_mm 80 80 1 80 ne ne ne ne ne ne 80 chars chars int chars floats floats floats floats floats floats chars

80 chars

80 1 80 mm mm

chars int chars floats floats

EnSight 7 User Manual

11-43

11.1 EnSight Gold Per_Element Variable File Format v33_m1 v12_m1 v13_m1 v23_m1 v33_m2 v12_m2 v13_m2 v23_m2 ... ... ... ... v33_mm v12_mm v13_mm v23_mm mm mm mm mm floats floats floats floats

TENSOR9 FILE:
description line 1 part # element type v11_e1 v11_e2 ... v11_ne v12_e1 v12_e2 ... v12_ne v13_e1 v13_e2 ... v13_ne v21_e1 v21_e2 ... v21_ne v22_e1 v22_e2 ... v22_ne v23_e1 v23_e2 ... v23_ne v31_e1 v31_e2 ... v31_ne v32_e1 v32_e2 ... v32_ne v33_e1 v33_e2 ... v33_ne element type . . part . . part # block # mm = (i-1)*(j-1)*(k-1) v11_m1 v11_m2 ... v11_mm v12_m1 v12_m2 ... v12_mm v13_m1 v13_m2 ... v13_mm v21_m1 v21_m2 ... v21_mm v22_m1 v22_m2 ... v22_mm v23_m1 v23_m2 ... v23_mm v31_m1 v31_m2 ... v31_mm v32_m1 v32_m2 ... v32_mm v33_m1 v33_m2 ... v33_mm 80 80 1 80 ne ne ne ne ne ne ne ne ne 80 chars chars int chars floats floats floats floats floats floats floats floats floats chars

80 chars

80 1 80 mm mm mm mm mm mm mm mm mm

chars int chars floats floats floats floats floats floats floats floats floats

COMPLEX SCALAR FILES (Real and/or Imaginary):

description line 1 part # element type s_e1 s_e2 ... s_ne element type . . part . . part # block s_m1 s_m2 ... s_mm 80 80 1 80 ne 80 chars chars int chars floats chars

80 chars

# mm = (i-1)*(j-1)*(k-1)

80 1 80 mm

chars int chars floats

COMPLEX VECTOR FILES (Real and/or Imaginary):

11-44

EnSight 7 User Manual

11.1 EnSight Gold Per_Element Variable File Format

description line 1 part # element type vx_e1 vx_e2 ... vx_ne vy_e1 vy_e2 ... vy_ne vz_e1 vz_e2 ... vz_ne element type . . part . . part # block # mm = (i-1)*(j-1)*(k-1) vx_m1 vx_m2 ... vx_mm vy_m1 vy_m2 ... vy_mm vz_m1 vz_m2 ... vz_mm

80 80 1 80 ne ne ne 80

chars chars int chars floats floats floats chars

80 chars

80 1 80 mm mm mm

chars int chars floats floats floats

ASCII form:
SCALAR FILE:
description line 1 part # element type s_e1 s_e2 . . s_ne element type . . part . . part # block s_m1 s_m2 . . s_mm A (max of 80 typ) A I10 A 12.5 1/line (ne)

# mm = (i-1)*(j-1)*(k-1)

A I10 A E12.5 1/line (mm)

VECTOR FILE:
description line 1 part # element type vx_e1 vx_e2 . A (max of 80 typ) A I10 A E12.5 1/line (ne)

EnSight 7 User Manual

11-45

11.1 EnSight Gold Per_Element Variable File Format . vx_ne vy_e1 vy_e2 . . vy_ne vz_e1 vz_e2 . . vz_ne element type . . part . . part # block vx_m1 vx_m2 . . vx_mm vy_m1 vy_m2 . . vy_mm vz_m1 vz_m2 . . vz_mm

E12.5 1/line (ne)

E12.5 1/line (ne)

# mm = (i-1)*(j-1)*(k-1)

A I10 A E12.5 1/line (mm)

E12.5 1/line (mm)

E12.5 1/line (mm)

TENSOR FILE:
description line 1 part # element type v11_e1 v11_e2 . . v11_ne v22_e1 v22_e2 . . v22_ne v33_e1 v33_e2 . . v33_ne v12_e1 v12_e2 . A (max of 80 typ) A I10 A E12.5 1/line (ne)

E12.5 1/line (ne)

E12.5 1/line (ne)

E12.5 1/line (ne)

11-46

EnSight 7 User Manual

11.1 EnSight Gold Per_Element Variable File Format . v12_ne v13_e1 v13_e2 . . v13_ne v23_e1 v23_e2 . . v23_ne element type . . part . . part # block v11_m1 v11_m2 . . v11_mm v22_m1 v22_m2 . . v22_mm v33_m1 v33_m2 . . v33_mm v12_m1 v12_m2 . . v12_mm v13_m1 v13_m2 . . v13_mm v23_m1 v23_m2 . . v23_mm

E12.5 1/line (ne)

E12.5 1/line (ne)

# mm = (i-1)*(j-1)*(k-1)

A I10 A E12.5 1/line (mm)

E12.5 1/line (mm)

E12.5 1/line (mm)

E12.5 1/line (mm)

E12.5 1/line (mm)

E12.5 1/line (mm)

TENSOR9 FILE:
description line 1 part # element type v11_e1 v11_e2 . A (max of 80 typ) A I10 A E12.5 1/line (ne)

EnSight 7 User Manual

11-47

11.1 EnSight Gold Per_Element Variable File Format . v11_ne v12_e1 v12_e2 . . v12_ne v13_e1 v13_e2 . . v13_ne v21_e1 v21_e2 . . v21_ne v22_e1 v22_e2 . . v22_ne v23_e1 v23_e2 . . v23_ne v31_e1 v31_e2 . . v31_ne v32_e1 v32_e2 . . v32_ne v33_e1 v33_e2 . . v33_ne element type . . part . . part # block v11_m1 v11_m2 . . v11_mm v12_m1 v12_m2 . . v12_mm

E12.5 1/line (ne)

E12.5 1/line (ne)

E12.5 1/line (ne)

E12.5 1/line (ne)

E12.5 1/line (ne)

E12.5 1/line (ne)

E12.5 1/line (ne)

E12.5 1/line (ne)

# mm = (i-1)*(j-1)*(k-1)

A I10 A E12.5 1/line (mm)

E12.5 1/line (mm)

11-48

EnSight 7 User Manual

11.1 EnSight Gold Per_Element Variable File Format v13_m1 v13_m2 . . v13_mm v21_m1 v21_m2 . . v21_mm v22_m1 v22_m2 . . v22_mm v23_m1 v23_m2 . . v23_mm v31_m1 v31_m2 . . v31_mm v32_m1 v32_m2 . . v32_mm v33_m1 v33_m2 . . v33_mm E12.5 1/line (mm)

E12.5 1/line (mm)

E12.5 1/line (mm)

E12.5 1/line (mm)

E12.5 1/line (mm)

E12.5 1/line (mm)

E12.5 1/line (mm)

COMPLEX SCALAR FILES (Real and/or Imaginary):

description line 1 part # element type s_e1 s_e2 . . s_ne element type . . part . . part # block s_m1 s_m2 . A (max of 80 typ) A I10 A 12.5 1/line (ne)

# mm = (i-1)*(j-1)*(k-1)

A I10 A E12.5 1/line (mm)

EnSight 7 User Manual

11-49

11.1 EnSight Gold Per_Element Variable File Format . s_mm

COMPLEX VECTOR FILES (Real and/or Imaginary):

description line 1 part # element type vx_e1 vx_e2 . . vx_ne vy_e1 vy_e2 . . vy_ne vz_e1 vz_e2 . . vz_ne element type . . part . . part # block vx_m1 vx_m2 . . vx_mm vy_m1 vy_m2 . . vy_mm vz_m1 vz_m2 . . vz_mm A (max of 80 typ) A I10 A E12.5 1/line (ne)

E12.5 1/line (ne)

E12.5 1/line (ne)

# mm = (i-1)*(j-1)*(k-1)

A I10 A E12.5 1/line (mm)

E12.5 1/line (mm)

E12.5 1/line (mm)

11-50

EnSight 7 User Manual

11.1 EnSight Gold Per_Element Variable File Format

The following variable file examples reflect scalar, vector, tensor, and complex variable values per element for the previously defined EnSight Gold Geometry File Example with 11 defined unstructured nodes and a 2x3x2 structured Part (Part number 3). The values are summarized in the following table
Note: These are the same values as listed in the EnSight6 per_element variable file section. Subsequently, the following example files contain the same data as the example files in the EnSight6 section - only they are listed in gold format.. (No asymmetric tensor example data given) Complex Scalar Element Element Scalar Index
Unstructured bar2 1 tria3 1 2 hexa8 1 Structured block 1 1 (5.) (5.1, 5.2, 5.3) (5.1, 5.2, 5.3, 5.4, 5.5, 5.6) (5.1) (5.2) 104 (4.) (4.1, 4.2, 4.3) (4.1, 4.2, 4.3, 4.4, 4.5, 4.6) (4.1) (4.2) 102 103 (2.) (3.) (2.1, 2.2, 2.3) (2.1, 2.2, 2.3, 2.4, 2.5, 2.6) (3.1, 3.2, 3.3) (3.1, 3.2, 3.3, 3.4, 3.5, 3.6) (2.1) (3.1) (2.2) (3.2) 101 (1.) (1.1, 1.2, 1.3) (1.1, 1.2, 1.3, 1.4, 1.5, 1.6) (1.1) (1.2)

Vector Values

Tensor (2nd order symm.) Real Values

Imaginary

Id

Value

Value Value

Per_element (Scalar) Variable Example 1: This example shows an ASCII scalar file (engold.Esca) for the gold geometry example.
Per_elem scalar values for the EnSight Gold geometry example part 1 tria3 2.00000E+00 3.00000E+00 hexa8 4.00000E+00 part 2 bar2 1.00000E+00 part 3 block 5.00000E+00 6.00000E+00

Per_element (Vector) Variable Example 2: This example shows an ASCII vector file (engold.Evec) for the gold geometry example.
Per_elem vector values for the EnSight Gold geometry example part 1 tria3 2.10000E+00 3.10000E+00 2.20000E+00 3.20000E+00

EnSight 7 User Manual

11-51

11.1 EnSight Gold Per_Element Variable File Format 2.30000E+00 3.30000E+00 hexa8 4.10000E+00 4.20000E+00 4.30000E+00 part 2 bar2 1.10000E+00 1.20000E+00 1.30000E+00 part 3 block 5.10000E+00 6.10000E+00 5.20000E+00 6.20000E+00 5.30000E+00 6.30000E+00

Per_element (Tensor) Variable Example3: This example shows an ASCII 2nd order symmetric tensor file (engold.Eten) for the gold geometry example.
Per_elem symmetric tensor values for the EnSight Gold geometry example part 1 tria3 2.10000E+00 3.10000E+00 2.20000E+00 3.20000E+00 2.30000E+00 3.30000E+00 2.40000E+00 3.40000E+00 2.50000E+00 3.50000E+00 2.60000E+00 3.60000E+00 hexa8 4.10000E+00 4.20000E+00 4.30000E+00 4.40000E+00 4.50000E+00 4.60000E+00 part 2 bar2 1.10000E+00 1.20000E+00 1.30000E+00 1.40000E+00 1.50000E+00 1.60000E+00 part 3 block

11-52

EnSight 7 User Manual

11.1 EnSight Gold Per_Element Variable File Format 5.10000E+00 6.10000E+00 5.20000E+00 6.20000E+00 5.30000E+00 6.30000E+00 5.40000E+00 6.40000E+00 5.50000E+00 6.50000E+00 5.60000E+00 6.60000E+00

Per_element (Complex) Variable Example 4: This example shows ASCII complex real (engold.Ecmp_r) and imaginary (engold.Ecmp_i) scalar files for the gold geometry example. (The same methodology would apply for complex real and imaginary vector files.)
Real scalar File: Per_elem complex real scalar values for the EnSight Gold geometry example part 1 tria3 2.10000E+00 3.10000E+00 hexa8 4.10000E+00 part 2 bar2 1.10000E+00 part 3 block 5.10000E+00 6.10000E+00 Imaginary scalar File: Per_elem complex imaginary scalar values for the EnSight Gold geometry example part 1 tria3 2.20000E+00 3.20000E+00 hexa8 4.20000E+00 part 2 bar2 1.20000E+00 part 3 block 5.20000E+00 6.20000E+00

EnSight 7 User Manual

11-53

11.1 EnSight Gold Undefined Variable Values Format

EnSight Gold Undefined Variable Values Format

Undefined variable values are allowed in EnSight Gold scalar, vector, tensor and complex variable file formats. Undefined values are specified on a per section basis (i.e. coordinates, element_type, or block) in each EnSight Gold variable file. EnSight first parses any undefined keyword undef that may follow the sectional keyword (i.e. coordinates undef, element_type undef, or block undef) on its line. This indicates that the next floating point value is the undefined value used in that section. EnSight reads this undefined value, reads all subsequent variable values for that section; and then converts any undefined (file section) values to an internal undefined value recognized computationally by EnSight (Note: the internal, or computational, undefined value can be changed by the user via the test: change_undef_value command before any data is read.) The following per_node and per_element ASCII scalar files contain examples of undefined values. For your comparison, these two files are the files engold.Nsca and engold.Esca written with some undefined values specified. Note that the undefined values per section need not be the same value; rather, it may be any value - usually outside the interval range of the variable. The same methodology applies to vector, tensor, and complex files. C Binary form: (Per_node)
SCALAR FILE:
description line 1 part # coordinates undef undef_value s_n1 s_n2 ... s_nn part . . part # block undef undef_value s_m1 s_m2 ... s_mm 80 chars 80 chars 1 int 80 chars 1 float nn floats 80 chars

# mm = i*j*k

80 chars 1 int 80 chars 1 float mm floats

Fortran Binary form: (Per_node)

SCALAR FILE:
description line 1 part # coordinates undef undef_value s_n1 s_n2 ... s_nn part . . part # 80 chars 80 chars 1 int 80 chars 1 float nn floats 80 chars

80 chars 1 int

11-54

EnSight 7 User Manual

11.1 EnSight Gold Undefined Variable Values Format block undef undef_value s_m1 s_m2 ... s_mm # mm = i*j*k 80 chars 1 float mm floats

ASCII form: (Per_node)

SCALAR FILE:
description line 1 part # coordinates undef undef_value s_n1 s_n2 . . s_nn part . . part # block undef undef_value s_m1 s_m2 . . s_mm A (max of 79 typ) A I10 A E12.5 E12.5 1/line (nn)

# mm = i*j*k

A I10 A E12.5 E12.5 1/line (mm)

Undefined per_node (Scalar) Variable Example: This example shows undefined data in an ASCII scalar file (engold.Nsca_u) for the gold geometry example.
Per_node undefined scalar values for the EnSight Gold geometry example part 1 coordinates undef -1.00000E+04 -1.00000E+04 3.00000E+00 4.00000E+00 5.00000E+00 6.00000E+00 7.00000E+00 8.00000E+00 9.00000E+00 1.00000E+01 1.10000E+01 part 2 coordinates 1.00000E+00 2.00000E+00 part 3 block undef -1.23450E-10 1.00000E+00 2.00000E+00

EnSight 7 User Manual

11-55

11.1 EnSight Gold Undefined Variable Values Format 3.00000E+00 4.00000E+00 5.00000E+00 -1.23450E-10 7.00000E+00 8.00000E+00 9.00000E+00 1.00000E+01 1.10000E+01 1.20000E+01

C Binary form: (Per_element)

SCALAR FILE:
description line 1 part # element type undef undef_value s_e1 s_e2 ... s_ne element type undef undef_value . . part . . part # block undef undef_value s_m1 s_m2 ... s_mm 80 chars 80 chars 80 chars 1 int 80 chars 1 float ne floats 80 chars 1 float

# mm = (i-1)*(j-1)*(k-1)

80 chars 1 int 80 chars 1 float mm floats

Fortran Binary form: (Per_element)

SCALAR FILE:
description line 1 part # element type undef undef_value s_e1 s_e2 ... s_ne element type undef undef_value . . part . . part # block undef undef_value 80 chars 80 chars 80 chars 1 int 80 chars 1 float ne floats 80 chars 1 float

# mm = (i-1)*(j-1)*(k-1)

80 chars 1 int 80 chars 1 float

11-56

EnSight 7 User Manual

11.1 EnSight Gold Undefined Variable Values Format s_m1 s_m2 ... s_mm mm floats

ASCII form: (Per_element)

SCALAR FILE:
description line 1 part # element type undef undef_value s_e1 s_e2 . . s_ne element type undef undef_value . . part . . part # block undef undef_value s_m1 s_m2 . . s_mm A (max of 80 typ) A I10 A E12.5 E12.5 1/line (ne)

A E12.5

# mm = (i-1)*(j-1)*(k-1)

A I10 A E12.5 E12.5 1/line (mm)

Undefined per_element (Scalar) Variable Example: This example shows undefined data in an ASCII scalar file (engold.Esca_u) for the gold geometry example.
Per_elem undefined scalar values for the EnSight Gold geometry example part 1 tria3 undef -1.00000E+02 2.00000E+00 -1.00000E+02 hexa8 4.00000E+00 part 2 bar2 1.00000E+00 part 3 block undef -1.23450E-10 -1.23450E-10 6.00000E+00

EnSight 7 User Manual

11-57

11.1 EnSight Gold Partial Variable Values Format

EnSight Gold Partial Variable Values Format

Partial variable values are allowed in EnSight Gold scalar, vector, tensor and complex variable file formats. Partial values are specified on a per section basis (i.e. coordinates, element_type, or block) in each EnSight Gold variable file. EnSight first parses any partial keyword partial that may follow the sectional keyword (i.e. coordinates partial, element_type partial, or block partial) on its line. This indicates that the next integer value is the number of partial values defined in that section. EnSight reads the number of defined partial values, next reads this number of integer partial indicies, and finally reads all corresponding partial variable values for that section. Afterwords, any variable value not specified in the list of partial indices is assigned the internal undefined (see previous section) value. Values interpolated between time steps must be defined for both time steps; otherwise, they are undefined. The following per_node and per_element ASCII scalar files contain examples of partial values. For your comparison, these two files are the files engold.Nsca and engold.Esca written with some partial values specified. The same methodology applies to vector, tensor, and complex files.

C Binary form: (Per_node)

SCALAR FILE:
description line 1 part # coordinates partial nn i_n1 i_n2 ... i_nn s_n1 s_n2 ... s_nn part . . part # block partial mm i_m1 i_m2 ... i_mm s_m1 s_m2 ... s_mm 80 80 1 80 1 nn nn 80 chars chars int chars int ints floats chars

# mm = i*j*k

80 1 80 1 mm mm

chars int chars int ints floats

Fortran Binary form: (Per_node)

SCALAR FILE:
description line 1 part # coordinates partial nn i_n1 i_n2 ... i_nn s_n1 s_n2 ... s_nn part . 80 chars 80 chars 1 int 80 chars 1 int nn ints nn floats 80 chars

11-58

EnSight 7 User Manual

11.1 EnSight Gold Partial Variable Values Format . part # block partial mm i_m1 i_m2 ... i_mm s_m1 s_m2 ... s_mm

# mm = i*j*k

80 chars 1 int 80 chars 1 int mm ints mm floats

ASCII form: (Per_node)

SCALAR FILE:
description line 1 part # coordinates partial nn i_n1 i_n2 . . i_nn s_n1 s_n2 . . s_nn part . . part # block partial mm i_m1 i_m2 . . i_mm s_m1 s_m2 . . s_mm A (max of 79 typ) A I10 A I10 I10 1/line (nn)

E12.5 1/line (nn)

# mm = i*j*k

A I10 A I10 I10 1/line (mm)

E12.5 1/line (mm)

Partial per_node (Scalar) Variable Example: This example shows partial data in an ASCII scalar file (engold.Nsca_p) for the gold geometry example.
Per_node partial scalar values for the EnSight Gold geometry example part 1 coordinates partial 9 2 3 4 5 6 7 8

EnSight 7 User Manual

11-59

11.1 EnSight Gold Partial Variable Values Format 9 10 3.00000E+00 4.00000E+00 5.00000E+00 6.00000E+00 7.00000E+00 8.00000E+00 9.00000E+00 1.00000E+01 1.10000E+01 part 2 coordinates 1.00000E+00 2.00000E+00 part 3 block 1.00000E+00 2.00000E+00 3.00000E+00 4.00000E+00 5.00000E+00 6.00000E+00 7.00000E+00 8.00000E+00 9.00000E+00 1.00000E+01 1.10000E+01 1.20000E+01

C Binary form: (Per_element)

SCALAR FILE:
description line 1 part # element type partial ne i_n1 i_n2 ... i_ne s_e1 s_e2 ... s_ne element type partial ne i_n1 i_n2 ... i_ne . . part . . part # block partial me i_m1 i_m2 ... i_me s_m1 s_m2 ... s_me 80 chars 80 chars 1 int 80 chars 1 int ne ints ne floats 80 chars 1 int ne ints

80 chars

# me= (i-1)*(j-1)*(k-1)

80 chars 1 int 80 chars 1 int me ints me floats

11-60

EnSight 7 User Manual

11.1 EnSight Gold Partial Variable Values Format

Fortran Binary form: (Per_element)

SCALAR FILE:
description line 1 part # element type partial ne i_n1 i_n2 ... i_ne s_e1 s_e2 ... s_ne element type partial ne i_n1 i_n2 ... i_ne . . part . . part # block partial me i_m1 i_m2 ... i_me s_m1 s_m2 ... s_me 80 chars 80 chars 1 int 80 chars 1 int ne ints ne floats 80 chars 1 int ne ints

80 chars

# me = (i-1)*(j-1)*(k-1)

80 chars 1 int 80 chars 1 int me ints me floats

ASCII form: (Per_element)

SCALAR FILE:
description line 1 part # element type partial ne i_n1 i_n2 . . i_ne s_e1 s_e2 . . s_ne element type partial ne i_n1 i_n2 . . i_ne . . part . . part A (max of 80 typ) A I10 A I10 I10 1/line (ne)

E12.5 1/line (ne)

A I10 I10 1/line (ne)

EnSight 7 User Manual

11-61

11.1 EnSight Gold Measured/Particle File Format # block partial me i_m1 i_m2 . . i_me s_m1 s_m2 . . s_me I10 A I10 I10 1/line (me)

# me = (i-1)*(j-1)*(k-1)

E12.5 1/line (me)

Partial per_element (Scalar) Variable Example: This example shows partial data in an ASCII scalar file (engold.Esca_p) for the gold geometry example.
Per_elem partial scalar values for the EnSight Gold geometry example part 1 tria3 partial 1 1 2.00000E+00 hexa8 4.00000E+00 part 2 bar2 1.00000E+00 part 3 block partial 1 2 6.00000E+00

EnSight Gold Measured/Particle File Format

The format of a Measured/Particle geometry file is as follows: Line 1 This line is a description line. Line 2 Indicates that this file contains particle coordinates. The words particle coordinates should be entered on this line without the quotes. Line 3 Specifies the number of Particles. Line 4 through the end of the file. Each line contains the ID and the X, Y, and Z coordinates of each Particle. The format of this line is integer real real real written out in the following format: From C:
%8d%12.5e%12.5e%12.5e format

11-62

EnSight 7 User Manual

11.1 EnSight Gold Measured/Particle File Format

From FORTRAN:
A description line particle coordinates #_of_Particles id xcoord ycoord zcoord id xcoord ycoord zcoord id xcoord ycoord zcoord . . .

i8, 3e12.5 format

A generic measured/Particle geometry file is as follows:

Measured Geometry Example

The following illustrates a measured/Particle file with seven points:

This is a simple measured geometry file particle coordinates 7 101 0.00000E+00 0.00000E+00 0.00000E+00 102 1.00000E+00 0.00000E+00 0.00000E+00 103 1.00000E+00 1.00000E+00 0.00000E+00 104 0.00000E+00 1.00000E+00 0.00000E+00 205 5.00000E-01 0.00000E+00 2.00000E+00 206 5.00000E-01 1.00000E+00 2.00000E+00 307 0.00000E+00 0.00000E+00-1.50000E+00

Measured Variable Files

Measured variable files are the same as EnSight6 case per_node variable files. Please note that they are NOT the same as the EnSight gold per_node variable files.

EnSight 7 User Manual

11-63

11.2 EnSight6 Casefile Format

11.2 EnSight6 Casefile Format

Included in this section: EnSight6 General Description EnSight6 Geometry File Format EnSight6 Case File Format EnSight6 Wild Card Name Specification EnSight6 Variable File Format EnSight6 Per_Node Variable File Format EnSight6 Per_Element Variable File Format EnSight6 Measured/Particle File Format Writing EnSight6 Binary Files

EnSight6 General Description

EnSight6 data consists of the following files: Case (required) (points to all other needed files including model geometry, variables, and possibly measured geometry and variables) EnSight6 supports constant result values as well as scalar, vector, 2nd order symmetric tensor, and complex variable fields. EnSight makes no assumptions regarding the physical significance of the variable values in the files. These files can be from any discipline. For example, the scalar file can include such things as pressure, temperature, and stress. The vector file can be velocity, displacement, or any other vector data. And so on. All variable results for EnSight6 are contained in disk filesone variable per file. Additionally, if there are multiple time steps, there must either be a set of disk files for each time step (transient multiple-file format), or all time steps of a particular variable or geometry in one disk file (transient single-file format). Thus, all EnSight6 transient geometry and variable files can be expressed in either multiple file format or single file format. Sources of EnSight6 data include the following: Data that can be translated to conform to the EnSight6 data format Data that originates from one of the translators supplied with the EnSight application The EnSight6 format supports an unstructured defined element set as shown in the figure on the following page. Unstructured data must be defined in this element set. Elements that do not conform to this set must either be subdivided or discarded. The EnSight6 format also supports a structured block data format which is very similar to the PLOT3D format. A given EnSight6 model may have either unstructured data, structured data, or a mixture of both.

11-64

EnSight 7 User Manual

11.2 EnSight6 General Description

Supported EnSight Elements

The elements that are supported by the EnSight6 format are: 1 point 1 two node bar 2 1 2 three node bar 7 3 6 1 2 1 4 3 5 2 1 2 4 3 8 1 5 2 4 3 6 3

three node triangle

six node triangle

four node quadrangle 5

eight node quadrangle 5 12 10 4 9 6 13 11

4 8 1 2 four node tetrahedron 3 1 5 2 9

4 10 3 7 6 1 5 node pyramid 7 6 3 8 5 17 1 16 13 12 4 20 6 18 15 14 11 10 2 1 4 3 8

3 7 2

ten node tetrahedron 8

13 node pyramid 7 19 3

2 eight node hexahedron 4 1 5 2 6 3

9 2 twenty node hexahedron 4 13 1 10 7 2 12 9 5 14 6 15 11 3 8

six node pentahedron (wedge)

Figure 2-2 Supported EnSight6 Elements

fifteen node pentahedron (wedge)

EnSight 7 User Manual

11-65

11.2 EnSight6 Geometry File Format

EnSight6 Geometry File Format

The EnSight6 format consists of keywords followed by information. The following seven items are important when working with EnSight6 geometry files: 1. You do not have to assign node IDs. If you do, the element connectivities are based on the node numbers. If you let EnSight assign the node IDs, the nodes are considered to be sequential starting at node 1, and element connectivity is done accordingly. If node IDs are set to off, they are numbered internally; however, you will not be able to display or query on them. If you have node IDs in your data, you can have EnSight ignore them by specifying node id ignore. Using this option may reduce some of the memory taken up by the Client and Server, but display and query on the nodes will not be available. 2. You do not need to specify element IDs. If you specify element IDs, or you let EnSight assign them, you can show them on the screen. If they are set to off, you will not be able to show or query on them. If you have element IDs in your data you can have EnSight ignore them by specifying element id ignore. Using this option will reduce some of the memory taken up by the Client and Server. This may or may not be a significant amount, and remember that display and query on the elements will not be available. 3. The format of integers and real numbers must be followed (See the Geometry Example below). 4. Integers are written out using the following integer format: From C: 8d format From FORTRAN: i8 format Real numbers are written out using the following floating-point format: From C: 12.5e format From FORTRAN: e12.5 format The number of integers or reals per line must also be followed! 5. By default, a Part is processed to show the outside boundaries. This representation is loaded to the Client host system when the geometry file is read (unless other attributes have been set on the workstation, such as feature angle). 6. Coordinates for unstructured data must be defined before any Parts can be defined. The different elements can be defined in any order (that is, you can define a hexa8 before a bar2). 7. A Part containing structured data cannot contain any unstructured element types or more than one block. Each structured Part is limited to a single block. A structured block is indicated by following the Part description line with either the block line or the block iblanked line. An iblanked block must contain an additional integer array of values at each node, traditionally called the iblank array. Valid iblank values for the EnSight format are:
0 for nodes which are exterior to the model, sometimes called blanked-out nodes 1 for nodes which are interior to the model, thus in the free stream and to be used <0 or >1 for any kind of boundary nodes

11-66

EnSight 7 User Manual

11.2 EnSight6 Geometry File Format

In EnSights structured Part building dialog, the iblank option selected will control which portion of the structured block is created. Thus, from the same structured block, the interior flow field part as well as a symmetry boundary part could be created.

Note: By default EnSight does not do any partial cell iblank processing. Namely, only complete cells containing no exterior nodes are created. It is possible to obtain partial cell processing by issuing the test:partial_cells_on command in the Command Dialog before reading the file. Generic Format Not all of the lines included in the following generic example file are necessary:
description line 1 description line 2 node id <off/given/assign/ignore> element id <off/given/assign/ignore> coordinates # of unstructured nodes id x y z id x y z id x y z . . . part # description line point number of points id nd id nd id nd . . . bar2 number of bar2s id nd nd id nd nd id nd nd . . . bar3 number of bar3s id nd nd nd id nd nd nd id nd nd nd . . . tria3 number of three node triangles id nd nd nd id nd nd nd id nd nd nd . . | | | All geometry files must | contain these first six lines | |

EnSight 7 User Manual

11-67

11.2 EnSight6 Geometry File Format . tria6 number of six node triangles id nd nd nd nd nd nd . . . quad4 number of quad 4s id nd nd nd nd id nd nd nd nd id nd nd nd nd id nd nd nd nd . . . quad8 number of quad 8s id nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd . . . tetra4 number of 4 node tetrahedrons id nd nd nd nd id nd nd nd nd id nd nd nd nd id nd nd nd nd . . . tetra10 number of 10 node tetrahedrons id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd . . . pyramid5 number of 5 node pyramids id nd nd nd nd nd id nd nd nd nd nd id nd nd nd nd nd id nd nd nd nd nd . . . pyramid13 number of 13 node pyramids id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd . . .

nd nd nd nd

nd nd nd nd

nd nd nd nd

11-68

EnSight 7 User Manual

11.2 EnSight6 Geometry File Format hexa8 number of 8 node hexahedrons id nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd . . . hexa20 number of 20 node hexahedrons id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd . . . penta6 number of 6 node pentahedrons id nd nd nd nd nd nd id nd nd nd nd nd nd id nd nd nd nd nd nd id nd nd nd nd nd nd id nd nd nd nd nd nd . . . penta15 number of 15 node pentahedrons id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd . . . part # description line block i j k x_m1 x_m2 x_m3 ..... x_mm y_m1 y_m2 y_m3 ..... y_mm z_m1 z_m2 z_m3 ..... z_mm part # description line block iblanked i j k x_m1 x_m2 x_m3 ..... x_mm y_m1 y_m2 y_m3 ..... y_mm z_m1 z_m2 z_m3 ..... z_mm ib_m1 ib_m2 ib_m3 .... ib_mm

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

#mm=i*j*k (6/line)

#mm=i*j*k (6/line) (10/line)

EnSight 7 User Manual

11-69

11.2 EnSight6 Geometry File Format

EnSight6 Geometry File Example

The following is an example of an ASCII EnSight6 geometry file with 11 defined unstructured nodes from which 2 unstructured parts are defined, and a 2x3x2 structured part as depicted in the above diagram. (See Case File Example 1 for reference to this file.)

This is the 1st description line of the EnSight6 geometry example This is the 2nd description line of the EnSight6 geometry example node id given element id given coordinates 11 15 4.00000e+00 0.00000e+00 0.00000e+00 31 3.00000e+00 0.00000e+00 0.00000e+00 20 5.00000e+00 0.00000e+00 0.00000e+00 40 6.00000e+00 0.00000e+00 0.00000e+00 22 5.00000e+00 1.00000e+00 0.00000e+00 44 6.00000e+00 1.00000e+00 0.00000e+00 55 6.00000e+00 3.00000e+00 0.00000e+00 60 5.00000e+00 0.00000e+00 2.00000e+00 61 6.00000e+00 0.00000e+00 2.00000e+00 62 6.00000e+00 1.00000e+00 2.00000e+00 63 5.00000e+00 1.00000e+00 2.00000e+00 part 1 2D uns-elements (description line for part 1) tria3 2 102 15 20 22 103 22 44 55 hexa8 1 104 20 40 44 22 60 61 62 part 2 1D uns-elements (description line for part 2) bar2 1 101 31 15 part 3

63

11-70

EnSight 7 User Manual

11.2 EnSight6 Case File Format

3D struct-part (description line for part 3) block iblanked 2 3 2 0.00000e+00 2.00000e+00 0.00000e+00 2.00000e+00 0.00000e+00 2.00000e+00 0.00000e+00 2.00000e+00 0.00000e+00 0.00000e+00 1.00000e+00 1.00000e+00 0.00000e+00 0.00000e+00 1.00000e+00 1.00000e+00 0.00000e+00 0.00000e+00 0.00000e+00 0.00000e+00 2.00000e+00 2.00000e+00 2.00000e+00 2.00000e+00 1 1 1 1 1 1 1 1

0.00000e+00 0.00000e+00 3.00000e+00 3.00000e+00 0.00000e+00 2.00000e+00 1

2.00000e+00 2.00000e+00 3.00000e+00 3.00000e+00 0.00000e+00 2.00000e+00 1 1

EnSight6 Case File Format

The Case file is an ASCII free format file that contains all the file and name information for accessing model (and measured) geometry, variable, and time information. It is comprised of five sections (FORMAT, GEOMETRY, VARIABLE, TIME, FILE) as described below: Notes: All lines in the Case file are limited to 79 characters. The titles of each section must be in all capital letters. Anything preceded by a # denotes a comment and is ignored. Comments may append information lines or be placed on their own lines. Information following : may be separated by white spaces or tabs. Specifications encased in [] are optional, as indicated. Format Section This is a required section which specifies the type of data to be read. Usage:
FORMAT type: ensight

Geometry Section

This is a required section which specifies the geometry information for the model (as well as measured geometry if present, and periodic match file (see Section 11.9, Periodic Matchfile Format) if present). Usage:
GEOMETRY model: measured: match: [ts] [ts] [fs] [fs] filename filename filename [change_coords_only] [change_coords_only]

where: ts = time set number as specified in TIME section. This is optional. fs = corresponding file set number as specified in FILE section below. filename = The filename of the appropriate file. -> Model or measured filenames for a static geometry case, and match filenames will not contain * wildcards. -> Model or measured filenames for a changing geometry case will contain * wildcards. change_coords_only = The option to indicate that the changing geometry (as indicated by wildcards in the filename) is coords only. Otherwise, changing geometry connectivity will be assumed.

Variable Section
EnSight 7 User Manual

This is an optional section which specifies the files and names of the variables.
11-71

11.2 EnSight6 Case File Format

Constant variable values can also be set in this section. Usage:

VARIABLE constant per case: scalar per node: vector per node: tensor symm per node: scalar per element: vector per element: tensor symm per element: scalar per measured node: vector per measured node: complex scalar per node: complex vector per node: complex scalar per element: complex vector per element: [ts] [ts] [ts] [ts] [ts] [ts] [ts] [ts] [ts] [ts] [ts] description description description description description description description description description description description const_value(s) filename filename filename filename filename filename filename filename Re_fn Im_fn Re_fn Im_fn Im_fn Im_fn

[fs] [fs] [fs] [fs] [fs] [fs] [fs] [fs] [fs] [fs]

freq freq freq freq

[ts] [fs] description Re_fn [ts] [fs] description Re_fn

where:

ts

fs description const_value(s) filename Re_fn Im_fn freq

= The corresponding time set number (or index) as specified in TIME section below. This is only required for transient constants and variables. = The corresponding file set number (or index) as specified in FILE section below. = The variable (GUI) name (ex. Pressure, Velocity, etc.) = The constant value. If constants change over time, then ns (see TIME section below) constant values of ts. = The filename of the variable file. Note: only transient filenames contain * wildcards. = The filename for the file containing the real values of the complex variable. = The filename for the file containing the imaginary values of the complex variable. = The corresponding harmonic frequency of the complex variable. For complex variables where harmonic frequency is undefined, simply use the text string: UNDEFINED.

Note: Note:

As many variable description lines as needed may be used. The variable description is limited to 19 characters in the current release. Variable names must not start with a numeric digit and must not contain any of the following reserved characters: ( ) [ ] + @ space ! # * ^ $ /

Time Section

This is an optional section for steady state cases, but is required for transient cases. It contains time set information. Shown below is information for one time set. Multiple time sets (up to 16) may be specified for measured data as shown in Case File Example 3 below. Usage:
TIME time set: ts [description] number of steps: ns filename start number: fs filename increment: fi time values: time_1 time_2 .... time_ns

or
11-72 EnSight 7 User Manual

11.2 EnSight6 Case File Format

TIME time set: number of steps: filename numbers: time values:

ts [description] ns fn time_1 time_2 .... time_ns

where: ts = timeset number. This is the number referenced in the GEOMETRY and VARIABLE sections. description = optional timeset description which will be shown in user interface. ns = number of transient steps fs = the number to replace the * wildcards in the filenames, for the first step fi = the increment to fs for subsequent steps time = the actual time values for each step, each of which must be separated by a white space and which may continue on the next line if needed fn = a list of numbers or indices, to replace the * wildcards in the filenames. File Section This section is optional for expressing a transient case with single-file formats. This section contains single-file set information. This information specifies the number of time steps in each file of each data entity, i.e. each geometry and each variable (model and/or measured). Each data entitys corresponding file set might have multiple continuation files due to system file size limit, i.e. ~2 GB for 32-bit and ~4 TB for 64-bit architectures. Each file set corresponds to one and only one time set, but a time set may be referenced by many file sets. The following information may be specified in each file set. For file sets where all of the time set data exceeds the maximum file size limit of the system, both filename index and number of steps are repeated within the file set definition for each continuation file required. Otherwise filename index may be omitted if there is only one file. File set information is shown in Case File Example 4 below.

Usage:
FILE file set: filename index: number of steps: fs fi # Note: only used when data continues in other files ns

where: fs = file set number. This is the number referenced in the GEOMETRY and VARIABLE sections above. ns = number of transient steps fi = file index number in the file name (replaces * in the filenames) Case File Example 1 The following is a minimal EnSight6 case file for a steady state model with some results.
Note: this (en6.case) file, as well as all of its referenced geometry and variable files (along with a couple of command files) can be found under your installation directory (path: $ENSIGHT7_HOME/ data/user_manual). The EnSight6 Geometry File Example and the Variable File Examples are the contents of these files.
FORMAT type: ensight GEOMETRY model: en6.geo VARIABLE constant per case: scalar per element: scalar per node: Cden Esca Nsca .8 en6.Esca en6.Nsca

EnSight 7 User Manual

11-73

11.2 EnSight6 Case File Format

vector per element: vector per node: tensor symm per element: tensor symm per node: complex scalar per element: complex scalar per node: Evec Nvec Eten Nten Ecmp Ncmp en6.Evec en6.Nvec en6.Eten en6.Nten en6.Ecmp_r en6.Ecmp_i en6.Ncmp_r en6.Ncmp_i 2. 4.

Case File Example 2

The following is a Case file for a transient model. The connectivity of the geometry is also changing.
FORMAT type: ensight GEOMETRY model: VARIABLE scalar per node: vector per node: TIME time set: number of steps: filename start number: filename increment: time values: 1.0

example2.geo**

1 1

Stress Displacement

example2.scl** example2.dis**

2.0

1 3 0 1 3.0

The following files would be needed for Example 2:

example2.geo00 example2.geo01 example2.geo02 example2.scl00 example2.scl01 example2.scl02 example2.dis00 example2.dis01 example2.dis02

Case File Example 3

The following is a Case file for a transient model with measured data.

This example has pressure given per element.

FORMAT type: ensight

GEOMETRY model: measured:

1 2

example3.geo* example3.mgeo**

VARIABLE constant per case: constant per case: scalar per element vector per node: scalar per measured node: vector per measured node: TIME time set: number of steps: filename start number: filename increment: time values:

1 1 1 2 2

Gamma 1.4 Density .9 .9 Pressure Velocity Temperature Velocity

.7 .6 .6 example3.pre* example3.vel* example3.mtem** example3.mvel**

1 5 1 2 .1 .2 .3

# This example shows that time

11-74

EnSight 7 User Manual

11.2 EnSight6 Case File Format

.4 .5 2 6 0 2 # values can be on multiple lines

time set: number of steps: filename start number: filename increment: time values: .05 .15 .25 .34 .45 .55

The following files would be needed for Example 3:

example3.geo1 example3.geo3 example3.geo5 example3.geo7 example3.geo9 example3.mgeo00 example3.mgeo02 example3.mgeo04 example3.mgeo06 example3.mgeo08 example3.mgeo10 example3.pre1 example3.pre3 example3.pre5 example3.pre7 example3.pre9 example3.mtem00 example3.mtem02 example3.mtem04 example3.mtem06 example3.mtem08 example3.mtem10 example3.vel1 example3.vel3 example3.vel5 example3.vel7 example3.vel9 example3.mvel00 example3.mvel02 example3.mvel04 example3.mvel06 example3.mvel08 example3.mvel10

Case File Example 4

The following is Case File Example 3 expressed in transient single-file formats.

In this example, the transient data for the measured velocity data entity happens to be greater than the maximum file size limit. Therefore, the first four time steps fit and are contained in the first file, and the last two time steps are continued in a second file.
FORMAT type: ensight GEOMETRY model: measured: VARIABLE constant per case: scalar per element: vector per node: scalar per measured node: vector per measured node: TIME time set: number of steps: time values: time set: number of steps: time values: FILE file set: number of steps: file set:

1 2

example4.geo 1 example4.mgeo2

1 1 2 2

1 1 2 3

Density Pressure Velocity Temperature Velocity

.5 example4.pre example4.vel example4.mtem example4.mvel*

1 Model 5 .1 .2 .3 .4 .5 2 Measured 6 .05 .15 .25 .34 .45 .55

1 5 2

EnSight 7 User Manual

11-75

11.2 EnSight6 Case File Format

number of steps: file set: filename index: number of steps: filename index: number of steps: 6 3 1 4 2 2

The following files would be needed for Example 4:

example4.geo example4.mgeoe example4.pre xample4.mtem example4.vel example4.mvel1 example4.mvel2

Contents of Transient Single Files

Each file contains transient data that corresponds to the specified number of time steps. The data for each time step sequentially corresponds to the simulation time values (time values) found listed in the TIME section. In transient single-file format, the data for each time step essentially corresponds to a standard EnSight6 geometry or variable file (model or measured) as expressed in multiple file format. The data for each time step is enclosed between two wrapper records, i.e. preceded by a BEGIN TIME STEP record and followed by an END TIME STEP record. Time step data is not split between files. If there is not enough room to append the data from a time step to the file without exceeding the maximum file limit of a particular system, then a continuation file must be created for the time step data and any subsequent time step. Any type of user comments may be included before and/or after each transient step wrapper.

Note 1: If transient single file format is used, EnSight expects all files of a dataset to be specified in transient single file format. Thus, even static files must be enclosed between a BEGIN TIME STEP and an END TIME STEP wrapper. Note 2: For binary geometry files, the first BEGIN TIME STEP wrapper must follow the <C Binary/Fortran Binary> line. Both BEGIN TIME STEP and END TIME STEP wrappers are written according to type (1) in binary. (see Writing EnSight6 Binary Files, in Section 11.2) Note 3: Efficient reading of each file (especially binary) is facilitated by appending each file with a file index. A file index contains appropriate information to access the file byte positions of each time step in the file. (EnSight automatically appends a file index to each file when exporting in transient single file format.) If used, the file index must follow the last END TIME STEP wrapper in each file.
File Index Usage: ASCII
%20d\n %20d\n %20d\n ... %20d\n %20d\n %20d\n %s\n
*

Binary
sizeof(int) sizeof(long) sizeof(long) ... sizeof(long) sizeof(int) sizeof(long) sizeof(char)*80

Item
n fb1 fb2 ... fbn flag fb of item n
FILE_INDEX

Description
Total number of data time steps in the file. File byte loc for contents of 1st time step* File byte loc for contents of 2nd time step* ... File byte loc for contents of nth time step* Miscellaneous flag (= 0 for now) File byte loc for Item n above File index keyword

Each file byte location is the first byte that follows the BEGIN TIME STEP record.

Shown below are the contents of each of the above files, using the data files from Case

11-76

EnSight 7 User Manual

11.2 EnSight6 Case File Format

File Example 3 for reference (without FILE_INDEX for simplicity).

Contents of file example4.geo_1:
BEGIN TIME STEP Contents of file example3.geo1 END TIME STEP BEGIN TIME STEP Contents of file example3.geo3 END TIME STEP BEGIN TIME STEP Contents of file example3.geo5 END TIME STEP BEGIN TIME STEP Contents of file example3.geo7 END TIME STEP BEGIN TIME STEP Contents of file example3.geo9 END TIME STEP

Contents of file example4.pre_1:

BEGIN TIME STEP Contents of file example3.pre1 END TIME STEP BEGIN TIME STEP Contents of file example3.pre3 END TIME STEP BEGIN TIME STEP Contents of file example3.pre5 END TIME STEP BEGIN TIME STEP Contents of file example3.pre7 END TIME STEP BEGIN TIME STEP Contents of file example3.pre9 END TIME STEP

Contents of file example4.vel_1:

BEGIN TIME STEP Contents of file example3.vel1 END TIME STEP BEGIN TIME STEP Contents of file example3.vel3 END TIME STEP BEGIN TIME STEP Contents of file example3.vel5 END TIME STEP BEGIN TIME STEP Contents of file example3.vel7 END TIME STEP BEGIN TIME STEP Contents of file example3.vel9 END TIME STEP

Contents of file example4.mgeo_1:

BEGIN TIME STEP Contents of file example3.mgeo00 END TIME STEP BEGIN TIME STEP Contents of file example3.mgeo02 END TIME STEP BEGIN TIME STEP Contents of file example3.mgeo04 END TIME STEP BEGIN TIME STEP Contents of file example3.mgeo06 END TIME STEP BEGIN TIME STEP Contents of file example3.mgeo08 END TIME STEP BEGIN TIME STEP Contents of file example3.mgeo10 END TIME STEP

Contents of file example4.mtem_1:

BEGIN TIME STEP Contents of file example3.mtem00 END TIME STEP BEGIN TIME STEP Contents of file example3.mtem02 END TIME STEP BEGIN TIME STEP Contents of file example3.mtem04 END TIME STEP BEGIN TIME STEP Contents of file example3.mtem06

EnSight 7 User Manual

11-77

11.2 EnSight6 Variable File Format

END TIME STEP BEGIN TIME STEP Contents of file example3.mtem08 END TIME STEP BEGIN TIME STEP Contents of file example3.mtem10 END TIME STEP

Contents of file example4.mvel1_1:

BEGIN TIME STEP Contents of file example3.mvel00 END TIME STEP BEGIN TIME STEP Contents of file example3.mvel02 END TIME STEP BEGIN TIME STEP Contents of file example3.mvel04 END TIME STEP BEGIN TIME STEP Contents of file example3.mvel06 END TIME STEP

Contents of file example4.mvel2_1:

Comments can precede the beginning wrapper here.

BEGIN TIME STEP Contents of file example3.mvel08 END TIME STEP Comments can go between time step wrappers here. BEGIN TIME STEP Contents of file example3.mvel10 END TIME STEP

Comments can follow the ending time step wrapper.

EnSight6 Wild Card Name Specification

For transient data, if multiple time files are involved, the file names must conform to the EnSight wild-card specification. This specification is as follows: File names must include numbers that are in ascending order from beginning to end. Numbers in the files names must be zero filled if there is more than one significant digit. Numbers can be anywhere in the file name. When the file name is specified in the EnSight result file, you must replace the numbers in the file with an asterisk(*). The number of asterisks specified is the number of significant digits. The asterisk must occupy the same place as the numbers in the file names.

EnSight6 Variable File Format

EnSight6 variable files can either be per_node or per_element. They cannot be both. However, an EnSight model can have some variables which are per_node and other variables which are per_element.

EnSight6 Per_Node Variable File Format

EnSight6 variable files for per_node variables contain any values for each unstructured node followed by any values for each structured node. First comes a single description line. Second comes any unstructured node value. The number of values per node
11-78 EnSight 7 User Manual

11.2 EnSight6 Per_Node Variable File Format

depends on the type of field. An unstructured scalar field has one, a vector field has three (order: x,y,z), a 2nd order symmetric tensor field has 6 (order: 11, 22, 33, 12, 13, 23), and a 2nd order asymmetric tensor field has 9 values per node (order: 11, 12, 13, 21, 22, 23, 31, 32, 33). An unstructured complex variable in EnSight6 consists of two scalar or vector fields (one real and one imaginary), with scalar and vector values written to their separate files respectively. Third comes any structured data information, starting with a part # line, followed by a line containing the block, and then lines containing the values for each structured node which are output in the same IJK component order as the coordinates. Briefly, a structured scalar is the same as an unstructured scalar, one value per node. A structured vector is written one value per node per component, thus three sequential scalar field blocks. Likewise for a structured 2nd order symmetric tensor, written as six sequential scalar field blocks, and a 2nd order tensor, written as nine sequential scalar field blocks. The same methodology applies for a complex variable only with the real and imaginary fields written to separate structured scalar or vector files. The values must be written in the following floating point format (6 per line as shown in the examples below): From C: From FORTRAN: Line 1 This line is a description line. Line 2 through the end of the file contains the values at each node in the model. A generic example for per_node variables:
One description line for *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** part # *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** part # *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** the entire file *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** 12.5e e12.5

format format

The format of a per_node variable file is as follows:

The following variable file examples reflect scalar, vector, tensor, and complex variable values per node for the previously defined EnSight6 Geometry File Example with 11 defined unstructured nodes and a 2x3x2 structured Part (Part

EnSight 7 User Manual

11-79

11.2 EnSight6 Per_Node Variable File Format

number 3). The values are summarized in the following table.

ComplexScalar Node Node Scalar Vector Index Id
Unstructured 1 2 3 4 5 6 7 8 9 10 11 Structured 1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9 10 11 12 (1.) (2.) (3.) (4.) (5.) (6.) (7.) (8.) (9.) (10.) (11.) (12.) (1.1, 1.2, 1.3) (2.1, 2.2, 2.3) (3.1, 3.2, 3.3) (4.1, 4.2, 4.3) (5.1, 5.2, 5.3) (6.1, 6.2, 6.3) (7.1, 7.2, 7.3) (8.1, 8.2, 8.3) (9.1, 9.2, 9.3) (10.1,10.2,10.3) (11.1,11.2,11.3) (12.1,12.2,12.3) (1.1, 1.2, 1.3, 1.4, 1.5, 1.6) (2.1, 2.2, 2.3, 2.4, 2.5, 2.6) (3.1, 3.2, 3.3, 3.4, 3.5, 3.6) (4.1, 4.2, 4.3, 4.4, 4.5, 4.6) (5.1, 5.2, 5.3, 5.4, 5.5, 5.6) (6.1, 6.2, 6.3, 6.4, 6.5, 6.6) (7.1, 7.2, 7.3, 7.4, 7.5, 7.6) (8.1, 8.2, 8.3, 8.4, 8.5, 8.6) (9.1, 9.2, 9.3, 9.4, 9.5, 9.6) (10.1,10.2,10.3,10.4,10.5,10.6) (11.1,11.2,11.3,11.4,11.5,11.6) (12.1,12.2,12.3,12.4,12.5,12.6) (1.1) (2.1) (3.1) (4.1) (5.1) (6.1) (7.1) (8.1) (9.1) (10.1) (11.1) (12.1) (1.2) (2.2) (3.2) (4.2) (5.2) (6.2) (7.2) (8.2) (9.2) (10.2) (11.2) (12.2) 15 31 20 40 22 44 55 60 61 62 63 (1.) (2.) (3.) (4.) (5.) (6.) (7.) (8.) (9.) (10.) (11.) (1.1, 1.2, 1.3) (2.1, 2.2, 2.3) (3.1, 3.2, 3.3) (4.1, 4.2, 4.3) (5.1, 5.2, 5.3) (6.1, 6.2, 6.3) (7.1, 7.2, 7.3) (8.1, 8.2, 8.3) (9.1, 9.2, 9.3) (10.1,10.2,10.3) (11.1,11.2,11.3) (1.1, 1.2, 1.3, 1.4, 1.5, 1.6) (2.1, 2.2, 2.3, 2.4, 2.5, 2.6) (3.1, 3.2, 3.3, 3.4, 3.5, 3.6) (4.1, 4.2, 4.3, 4.4, 4.5, 4.6) (5.1, 5.2, 5.3, 5.4, 5.5, 5.6) (6.1, 6.2, 6.3, 6.4, 6.5, 6.6) (7.1, 7.2, 7.3, 7.4, 7.5, 7.6) (8.1, 8.2, 8.3, 8.4, 8.5, 8.60 (9.1, 9.2, 9.3, 9.4, 9.5, 9.6) (10.1,10.2,10.3,10.4,10.5,10.6) (11.1,11.2,11.3,11.4,11.5,11.6) (1.1) (2.1) (3.1) (4.1) (5.1) (6.1) (7.1) (8.1) (9.1) (10.1) (11.1) (1.2) (2.2) (3.2) (4.2) (5.2) (6.2) (7.2) (8.2) (9.2) (10.2) (11.2)

Tensor (2nd order symm.) Values

Real

Imaginary

Value

Values

Value Value

Per_node (Scalar) Variable Example 1 This example shows ASCII scalar file (en6.Nsca) for the geometry example.
Per_node scalar values for the EnSight6 geometry 1.00000E+00 2.00000E+00 3.00000E+00 4.00000E+00 7.00000E+00 8.00000E+00 9.00000E+00 1.00000E+01 part 3 block 1.00000E+00 2.00000E+00 3.00000E+00 4.00000E+00 7.00000E+00 8.00000E+00 9.00000E+00 1.00000E+01 example 5.00000E+00 6.00000E+00 1.10000E+01

5.00000E+00 6.00000E+00 1.10000E+01 1.20000E+01

Per_node (Vector) Variable Example 2 This example shows ASCII vector file (en6.Nvec) for the geometry example.
Per_node vector values for the EnSight6 geometry 1.10000E+00 1.20000E+00 1.30000E+00 2.10000E+00 3.10000E+00 3.20000E+00 3.30000E+00 4.10000E+00 5.10000E+00 5.20000E+00 5.30000E+00 6.10000E+00 7.10000E+00 7.20000E+00 7.30000E+00 8.10000E+00 9.l0000E+00 9.20000E+00 9.30000E+00 1.01000E+01 1.11000E+01 1.12000E+01 1.13000E+01 part 3 block 1.10000E+00 2.10000E+00 3.10000E+00 4.10000E+00 7.10000E+00 8.10000E+00 9.10000E+00 1.01000E_01 1.20000E+00 2.20000E+00 3.20000E+00 4.20000E+00 7.20000E+00 8.20000E+00 9.20000E+00 1.02000E+01 1.30000E+00 2.30000E+00 3.30000E+00 4.30000E+00 7.30000E+00 8.30000E+00 9.30000E+00 1.03000E+01 example 2.20000E+00 4.20000E+00 6.20000E+00 8.20000E+00 1.02000E+01 2.30000E+00 4.30000E+00 6.30000E+00 8.30000E+00 1.03000E+01

5.10000E+00 1.11000E+01 5.20000E+00 1.12000E+01 5.30000E+00 1.13000E+01

6.10000E+00 1.21000E+01 6.20000E+00 1.22000E+01 6.30000E+00 1.23000E+01

11-80

EnSight 7 User Manual

11.2 EnSight6 Per_Element Variable File Format

Per_node (Tensor) Variable Example 3 This example shows an ASCII 2nd order symmetric tensor file (en6.Nten) for the geometry example.
Per_node symmetric tensor values for 1.10000E+00 1.20000E+00 1.30000E+00 2.10000E+00 2.20000E+00 2.30000E+00 3.10000E+00 3.20000E+00 3.30000E+00 4.10000E+00 4.20000E+00 4.30000E+00 5.10000E+00 5.20000E+00 5.30000E+00 6.10000E+00 6.20000E+00 6.30000E+00 7.10000E+00 7.20000E+00 7.30000E+00 8.10000E+00 8.20000E+00 8.30000E+00 9.10000E+00 9.20000E+00 9.30000E+00 1.01000E+01 1.02000E+01 1.03000E+01 1.11000E+01 1.12000E+01 1.13000E+01 part 3 block 1.10000E+00 2.10000E+00 3.10000E+00 7.10000E+00 8.10000E+00 9.10000E+00 1.20000E+00 2.20000E+00 3.20000E+00 7.20000E+00 8.20000E+00 9.20000E+00 1.30000E+00 2.30000E+00 3.30000E+00 7.30000E+00 8.30000E+00 9.30000E+00 1.40000E+00 2.40000E+00 3.40000E+00 7.40000E+00 8.40000E+00 9.40000E+00 1.50000E+00 2.50000E+00 3.50000E+00 7.50000E+00 8.50000E+00 9.50000E+00 1.60000E+00 2.60000E+00 3.60000E+00 7.60000E+00 8.60000E+00 9.60000E+00 the EnSight6 geometry example 1.40000E+00 1.50000E+00 1.60000E+00 2.40000E+00 2.50000E+00 2.60000E+00 3.40000E+00 3.50000E+00 3.60000E+00 4.40000E+00 4.50000E+00 4.60000E+00 5.40000E+00 5.50000E+00 5.60000E+00 6.40000E+00 6.50000E+00 6.60000E+00 7.40000E+00 7.50000E+00 7.60000E+00 8.40000E+00 8.50000E+00 8.60000E+00 9.40000E+00 9.50000E+00 9.60000E+00 1.04000E+01 1.05000E+01 1.06000E+01 1.14000E+01 1.15000E+01 1.16000E+01

4.10000E+00 1.01000E+01 4.20000E+00 1.02000E+01 4.30000E+00 1.03000E+01 4.40000E+00 1.04000E+01 4.50000E+00 1.05000E+01 4.60000E+00 1.06000E+01

5.10000E+00 1.11000E+01 5.20000E+00 1.12000E+01 5.30000E+00 1.13000E+01 5.40000E+00 1.14000E+01 5.50000E+00 1.15000E+01 5.60000E+00 1.16000E+01

6.10000E+00 1.21000E+01 6.20000E+00 1.22000E+01 6.30000E+00 1.23000E+01 6.40000E+00 1.24000E+01 6.50000E+00 1.25000E+01 6.60000E+00 1.26000E+01

Per_node (Complex) Variable Example 4 This example shows the ASCII complex real (en6.Ncmp_r) and imaginary (en6.Ncmp_i) scalar files for the geometry example. (The same methodology would apply for complex real and imaginary vector files.)
Real scalar File:
Per_node complex real scalar values for the EnSight6 geometry example 1.10000E+00 2.10000E+00 3.10000E+00 4.10000E+00 5.10000E+00 6.10000E+00 7.10000E+00 8.10000E+00 9.10000E+00 1.01000E+01 1.11000E+01 part 3 block 1.10000E+00 2.10000E+00 3.10000E+00 4.10000E+00 5.10000E+00 6.10000E+00 7.10000E+00 8.10000E+00 9.10000E+00 1.01000E+01 1.11000E+01 1.21000E+00

Imaginary scalar File:

Per_node complex imaginary scalar values for the 1.20000E+00 2.20000E+00 3.20000E+00 4.20000E+00 7.20000E+00 8.20000E+00 9.20000E+00 1.02000E+01 part 3 block 1.20000E+00 2.20000E+00 3.20000E+00 4.20000E+00 7.20000E+00 8.20000E+00 9.20000E+00 1.02000E+01 EnSight6 geometry example 5.20000E+00 6.20000E+00 1.12000E+01

5.20000E+00 6.20000E+00 1.12000E+01 1.22000E+00

EnSight6 Per_Element Variable File Format

EnSight variable files for per_element variables contain values for each element of designated types of designated Parts. First comes a single description line. Second comes a Part line. Third comes an element type line and fourth comes the

EnSight 7 User Manual

11-81

11.2 EnSight6 Per_Element Variable File Format

value for each element of that type and part. If it is a scalar variable, there is one value per element, while for vector variables there are three values per element. (The number of elements of the given type are obtained from the corresponding EnSight6 geometry file.) The values must be written in the following floating point format (6 per line as shown in the examples below): From C: From FORTRAN: format e12.5 format
12.5e

The format of a per_element variable file is as follows: Line 1 This line is a description line. Line 2 Part line, with part number corresponding to the geometry file. Line 3 Element type line ( example: tria3, hexa8, ... ) Line 4 Repeats until next element type line, part line, or end of file is reached. Lists values for each element of this part and type.

A generic example for per_element variables:

One description line for the entire file part #

element type
*.*****E+** *.*****E+** part # block *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+**

*.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+**

*.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+**

*.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+**

11-82

EnSight 7 User Manual

11.2 EnSight6 Per_Element Variable File Format

The following variable file examples reflect scalar, vector, tensor, and complex variable values per element for the previously defined EnSight6 Geometry File Example with 11 defined unstructured nodes and a 2x3x2 structured Part (Part number 3). The values are summarized in the following table.
Complex Scalar Element Element Scalar Index
Unstructured bar2 1 tria3 1 2 hexa8 1 Structured block 1 1 (5.) (5.1, 5.2, 5.3) (5.1, 5.2, 5.3, 5.4, 5.5, 5.6) (5.1) (5.2) 104 (4.) (4.1, 4.2, 4.3) (4.1, 4.2, 4.3, 4.4, 4.5, 4.6) (4.1) (4.2) 102 103 (2.) (3.) (2.1, 2.2, 2.3) (2.1, 2.2, 2.3, 2.4, 2.5, 2.6) (3.1, 3.2, 3.3) (3.1, 3.2, 3.3, 3.4, 3.5, 3.6) (2.1) (3.1) (2.2) (3.2) 101 (1.) (1.1, 1.2, 1.3) (1.1, 1.2, 1.3, 1.4, 1.5, 1.6) (1.1) (1.2)

Vector Values

Tensor (2nd order symm.) Real Values

Imaginary

Id

Value

Value Value

Per_element (Scalar) Variable Example 1 This example shows an ASCII scalar file (en6.Esca) for the geometry example.
Per_elem scalar values for the EnSight6 geometry example part 1 tria3 2.00000E+00 3.00000E+00 hexa8 4.00000E+00 part 2 bar2 1.00000E+00 part 3 block 5.00000E+00 6.00000E+00

Per_element (Vector) Variable Example 2 This example shows an ASCII vector file (en6.Evec) for the geometry example.
Per_elem vector values for the EnSight6 geometry example part 1 tria3 2.10000E+00 2.20000E+00 2.30000E+00 3.10000E+00 3.20000E+00 3.30000E+00 hexa8 4.10000E+00 4.20000E+00 4.30000E+00 part 2 bar2 1.10000E+00 1.20000E+00 1.30000E+00 part 3 block 5.10000E+00 6.10000E+00 5.20000E+00 6.20000E+00 5.30000E+00 6.30000E+00

EnSight 7 User Manual

11-83

11.2 EnSight6 Per_Element Variable File Format

Per_element (Tensor) Variable Example 3 This example shows the ASCII 2nd order symmetric tensor file (en6.Eten) for the geometry example.
Per_elem symmetric tensor values for part 1 tria3 2.10000E+00 2.20000E+00 2.30000E+00 3.10000E+00 3.20000E+00 3.30000E+00 hexa8 4.10000E+00 4.20000E+00 4.30000E+00 part 2 bar2 1.10000E+00 1.20000E+00 1.30000E+00 part 3 block 5.10000E+00 6.10000E+00 5.20000E+00 6.20000E+00 5.30000E+00 6.30000E+00 5.40000E+00 6.40000E+00 5.50000E+00 6.50000E+00 5.60000E+00 6.60000E+00 the EnSight6 geometry example

2.40000E+00 2.50000E+00 2.60000E+00 3.40000E+00 3.50000E+00 3.60000E+00 4.40000E+00 4.50000E+00 4.60000E+00

1.40000E+00 1.50000E+00 1.60000E+00

Per_element (Complex) Variable Example 4 This example shows the ASCII complex real (en6.Ecmp_r) and imaginary (en6.Ecmp_i) scalar files for the geometry example. (The same methodology would apply for complex real and imaginary vector files).
Real scalar File:
Per_elem complex real scalar values for the EnSight6 geometry example part 1 tria3 2.10000E+00 3.10000E+00 hexa8 4.10000E+00 part 2 bar2 1.10000E+00 part 3 block 5.10000E+00 6.10000E+00

Imaginary scalar File:

Per_elem complex imaginary scalar values for the EnSight6 geometry example part 1 tria3 2.20000E+00 3.20000E+00 hexa8 4.20000E+00 part 2 bar2 1.20000E+00 part 3 block 5.20000E+00 6.20000E+00

11-84

EnSight 7 User Manual

11.2 EnSight6 Measured/Particle File Format

EnSight6 Measured/Particle File Format

The format of a Measured/Particle geometry file is as follows: Line 1 This line is a description line. Line 2 Indicates that this file contains particle coordinates. The words particle coordinates should be entered on this line without the quotes. Line 3 Specifies the number of Particles. Line 4 through the end of the file. Each line contains the ID and the X, Y, and Z coordinates of each Particle. The format of this line is integer real real real written out in the following format: From C: From FORTRAN:
A description line particle coordinates #_of_Particles id xcoord ycoord zcoord id xcoord ycoord zcoord id xcoord ycoord zcoord . . .

%8d%12.5e%12.5e%12.5e format i8, 3e12.5 format

A generic measured/Particle geometry file is as follows:

Measured Geometry Example

The following illustrates a measured/Particle file with seven points:

This is a simple measured geometry file particle coordinates 7 101 0.00000E+00 0.00000E+00 0.00000E+00 102 1.00000E+00 0.00000E+00 0.00000E+00 103 1.00000E+00 1.00000E+00 0.00000E+00 104 0.00000E+00 1.00000E+00 0.00000E+00 205 5.00000E-01 0.00000E+00 2.00000E+00 206 5.00000E-01 1.00000E+00 2.00000E+00 307 0.00000E+00 0.00000E+00-1.50000E+00

Measured Variable Files

Measured variable files use the same format as EnSight6 per_node variable files.

Writing EnSight6 Binary Files

This section describes the EnSight6 binary files. This format is used to increase the speed of reading data into EnSight.

EnSight 7 User Manual

11-85

11.2 Writing EnSight6 Binary Files

For binary files, there is a header that designates the type of binary file. This header is: C Binary or Fortran Binary. This must be the first thing in the geometry file only. The format for the file is then essentially the same format as the ASCII format, with the following exceptions: The ASCII format puts the node and element ids on the same line as the corresponding coordinates. The BINARY format writes all node ids then all coordinates. The ASCII format puts all element ids of a type within a Part on the same line as the corresponding connectivity. The BINARY format writes all the element ids for that type, then all the corresponding connectivities of the elements. FORTRAN binary files should be created as sequential access unformatted files. In all the descriptions of binary files that follow, the number on the left end of the line corresponds to the type of write of that line, according to the following code: 1. This is a write of 80 characters to the file: C example:
char buffer[80]; strcpy(buffer,C Binary); fwrite(buffer,sizeof(char),80,file_ptr);

FORTRAN:

character*80

buffer

buffer = Fortran Binary write(10) buffer

2. This is a write of a single integer: C example: FORTRAN:

fwrite(&num_nodes,sizeof(int),1,file_ptr); write(10) num_nodes

3. This is a write of an integer array:

C example: fwrite(node_ids,sizeof(int),num_nodes,file_ptr); FORTRAN:write(10) (node_ids(i),i=1,num_nodes)

4. This is a write of a float array: C example: fwrite(coords,sizeof(float),3*num_nodes,file_ptr); FORTRAN: write(10) ((coords(i,j),i=1,3),j=1,num_nodes) (NOTE: Coords is a single precision array, double precision will not work!)

11-86

EnSight 7 User Manual

11.2 Writing EnSight6 Binary Files

EnSight6 Binary Geometry

An EnSight binary geometry file contains information in the following order: (1) (1) (1) (1) (1) (1) (2) (3) (4) (1) (1) (1) (2) (3) (3) (1) (2) (3) (3)

<C Binary/Fortran Binary> description line 1 description line 2 node id <given/off/assign/ignore> element id <given/off/assign/ignore> coordinates #_of_points [point_ids] coordinate_array part # description line element_type #_of_element_type [element_ids] for the element_type connectivities for the element_type element_type #_of_element_type [element_ids] for the element_type connectivities for the element_type : (1) part # (1) description line (1) element_type (2) #_of_element_type (3) [element_ids] for the element_type (3) connectivities for the element_type (1) element_type (2) #_of_element_type (3) [element_ids] for the element_type (3) connectivities for the element_type (1) part # (1) description line (1) block [iblanked] (3) i j k (4) all i coords, all j coords, all k coords (3) [iblanking] : Per_node Binary Scalar An EnSight6 binary scalar file contains information in the following order: (1) (4) (1) (1) (4) Per_node Binary Vector description line scalar_array for unstructured nodes part # block scalar_array for parts structured nodes

An EnSight6 binary vector file contains information in the following order: (1) description line (4) vector_array for unstructured nodes (1) part #

EnSight 7 User Manual

11-87

11.2 Writing EnSight6 Binary Files

(1) block (4) vector_array for parts structured nodes Per_node Binary Tensor An EnSight6 binary tensor file contains information in the following order: (1) (4) (1) (1) (4) description line tensor_array for unstructured nodes part # block tensor_array for parts structured nodes

Per_node Binary Complex An EnSight6 binary complex real and imaginary scalar files contain information in the following order: (The same methodology applies for the complex real and imaginary vector files.) Real scalar file: (1) (4) (1) (1) (4) Imaginary scalar file: (1) (4) (1) (1) (4) Per_element Binary Scalar (1) (1) (1) (4) Per_element Binary Vector (1) (1) (1) (4) Per_element Binary Tensor (1) (1) (1) (4) (1) (1) (4) description line imaginary scalar_array for unstructured nodes part # block imaginary scalar_array for parts structured nodes An EnSight6 binary scalar file contains information in the following order: description line part # element type (tria3, quad4, ...) scalar_array for elements of part and type An EnSight6 binary vector file contains information in the following order: description line part # element type (tria3, quad4, ...) vector_array for elements of part and type An EnSight6 binary tensor file contains information in the following order: description line part # element type (tria3, quad4, ...) tensor_array for unstructured elements of part and type part # block tensor_array for structured elements of part and type description line real scalar_array for unstructured nodes part # block real scalar_array for parts structured nodes

11-88

EnSight 7 User Manual

11.2 Writing EnSight6 Binary Files

Per_element Binary Complex EnSight6 binary complex real and imaginary scalar files contain information in the following order: (The same methodology applies for the complex real and imaginary vector files.) Real scalar file: (1) (1) (1) (4) (1) (1) (4) description line part # element type (tria3, quad4, ...) real scalar_array for unstructured elements of part and type part # block real scalar_array for structured elements of part and type

Imaginary scalar file: (1) description line (1) part # (1) element type (tria3, quad4, ...) (4) imaginary scalar_array for unstructured elements of part and type (1) part # (1) block (4) imaginary scalar_array for structured elements of part and type Binary Measured Geometry An EnSight6 binary measured/particle geometry file contains information in the following order: (1) (1) (1) (2) (3) (4) Binary Measured Variable Files <C Binary/Fortran Binary> description line 1 particle coordinates #_of_points point_ids coordinate_array

EnSight6 binary measured/discrete particle scalar and vector files follow the same binary formats as EnSight6 model per-node scalar and vector files.

EnSight 7 User Manual

11-89

11.3 EnSight5 Format

11.3 EnSight5 Format

Included in this section: EnSight5 General Description EnSight5 Geometry File Format EnSight5 Result File Format EnSight5 Wild Card Name Specification EnSight5 Variable File Format EnSight5 Measured/Particle File Format Writing EnSight5 Binary Files

EnSight5 General Description

Note: The EnSight6 format replaces and includes all aspects of the older EnSight5 format. This description is included for completeness but use of the EnSight6 format with EnSight 6.x and later versions is encouraged! EnSight5 data consists of the following files: Geometry (required) Results (optional) (points to other variable files and possibly to changing geometry files) Measured (optional) (points to measured geometry and variable files) The results file contains information concerning scalar and vector variables. EnSight makes no assumptions regarding the physical significance of the scalar and vector variables. These files can be from any discipline. For example, the scalar file can include such things as pressure, temperature, and stress. The vector file can be velocity, displacement, or any other vector data. All variable results for EnSight5 are contained in disk filesone variable per file. Additionally, if there are multiple time steps, there must be a set of disk files for each time step. Sources of EnSight5 data include the following: Data that can be translated to conform to the EnSight5 data format Data that originates from one of the translators supplied with the EnSight application The EnSight5 format supports a defined element set as shown below. The data must be defined in this element set. Elements that do not conform to this set must either be subdivided or discarded.

11-90

EnSight 7 User Manual

11.3 EnSight5 General Description

Supported EnSight5 Elements

The elements that are supported by the EnSight5 format are: 1 point 1 two node bar 2 1 2 three node bar 7 3 6 1 2 1 4 3 5 2 1 2 4 3 8 1 5 2 4 3 6 3

three node triangle

six node triangle

four node quadrangle 5

eight node quadrangle 5 12 10 4 9 6 13 11

4 8 1 2 four node tetrahedron 3 1 5 2 9

4 10 3 7 6 1 5 node pyramid 7 6 3 8 5 17 1 16 13 12 4 20 6 18 15 14 11 10 2 1 4 3 8

3 7 2

ten node tetrahedron 8

13 node pyramid 7 19 3

2 eight node hexahedron 4 1 5 2 6 3

2 9 twenty node hexahedron 4 13 1 10 7 2 12 9 5 14 11 8 6 15 3

six node pentahedron (wedge)

Figure 2-3 Supported EnSight5 Elements

fifteen node pentahedron (wedge)

EnSight 7 User Manual

11-91

11.3 EnSight5 Geometry File Format

EnSight5 Geometry File Format

The EnSight5 format consists of keywords followed by information. The following items are important to remember when working with EnSight5 geometry files: 1. You do not have to assign node IDs. If you do, the element connectivities are based on the node numbers. If you let EnSight assign the node IDs, the nodes are considered to be sequential starting at node 1, and element connectivity is done accordingly. If node IDs are set to off, they are numbered internally; however, you will not be able to display or query on them. If you have node IDs in your data, you can have EnSight ignore them by specifying node id ignore. Using this option may reduce some of the memory taken up by the Client and Server, but remember that display and query on the nodes will not be available. 2. You do not need to specify element IDs. If you specify element IDs, or you let EnSight assign them, you can show them on the screen. If they are set to off, you will not be able to show or query on them. If you have element IDs in your data you can have EnSight ignore them by specifying element id ignore. Using this option will reduce some of the memory taken up by the Client and Server. This may or may not be a significant amount, and remember that display and query on the elements will not be available. 3. The format of integers and real numbers must be followed (See the Geometry Example below). 4. Integers are written out using the following integer format: From C: From FORTRAN: From C: From FORTRAN:
8d i8

format format

Real numbers are written out using the following floating-point format:
12.5e format e12.5 format

The number of integers or reals per line must also be followed! 5. By default, a Part is processed to show the outside boundaries. This representation is loaded to the Client host system when the geometry file is read (unless other attributes have been set on the workstation, such as feature angle). 6. Coordinates must be defined before any Parts can be defined. The different elements can be defined in any order (that is, you can define a hexa8 before a bar2).
Generic Format

Not all of the lines included in the following generic example file are necessary:
description line 1 description line 2 node id <off/given/assign/ignore> element id <off/given/assign/ignore> coordinates # of points id x y z id x y z

11-92

EnSight 7 User Manual

11.3 EnSight5 Geometry File Format id x y z . . . part # description line point number of points id nd nd id nd nd id nd nd . . . bar2 number of bar2s id nd nd id nd nd id nd nd . . . bar3 number of bar3s id nd nd nd id nd nd nd id nd nd nd . . . tria3 number of three node triangles id nd nd nd id nd nd nd id nd nd nd . . . tria6 number of six node triangles id nd nd nd nd nd nd . . . quad4 number of quad 4s id nd nd nd nd id nd nd nd nd id nd nd nd nd id nd nd nd nd . . . quad8 number of quad 8s id nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd . .

EnSight 7 User Manual

11-93

11.3 EnSight5 Geometry File Format . tetra4 number of 4 node tetrahedrons id nd nd nd nd id nd nd nd nd id nd nd nd nd id nd nd nd nd . . . tetra10 number of 10 node tetrahedrons id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd . . . pyramid5 number of 5 node pyramids id nd nd nd nd nd id nd nd nd nd nd id nd nd nd nd nd id nd nd nd nd nd . . . pyramid13 number of 13 node pyramids id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd . . . hexa8 number of 8 node hexahedrons id nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd . . . hexa20 number of 20 node hexahedrons id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd id nd nd nd nd nd nd nd nd nd nd . . . penta6 number of 6 node pentahedrons id nd nd nd nd nd nd id nd nd nd nd nd nd id nd nd nd nd nd nd

nd nd nd nd

nd nd nd nd

nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

11-94

EnSight 7 User Manual

11.3 EnSight5 Geometry File Format id nd nd nd nd nd id nd nd nd nd nd . . . penta15 number of 15 node id nd nd nd nd nd id nd nd nd nd nd id nd nd nd nd nd id nd nd nd nd nd id nd nd nd nd nd . . . EnSight5 Geometry Example nd nd

pentahedrons nd nd nd nd nd nd nd nd nd nd nd nd nd nd nd nd nd nd nd nd nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

nd nd nd nd nd

The following is an example of an EnSight geometry file:

this is an example problem this is the second description line node id given element id given coordinates 10 5 1.00000e+00 0.00000e+00 0.00000e+00 100 0.00000e+00 1.00000e+00 0.00000e+00 200 0.00000e+00 0.00000e+00 1.00000e+00 40 1.00000e+00 1.00000e+00 0.00000e+00 22 1.00000e+00 0.00000e+00 1.00000e+00 1000 2.00000e+00 0.00000e+00 0.00000e+00 55 0.00000e+00 2.00000e+00 0.00000e+00 44 0.00000e+00 0.00000e+00 2.00000e+00 202 2.00000e+00 2.00000e+00 0.00000e+00 101 2.00000e+00 0.00000e+00 2.00000e+00 part 1 This is Part 1, a pretty strange Part tria3 2 101 100 200 40 201 101 5 1000 tetra4 1 102 100 202 101 1000 part 2 This is Part 2, its pretty strange also bar2 1 103 101 1000

EnSight 7 User Manual

11-95

11.3 EnSight5 Result File Format

EnSight5 Result File Format

The Result file is an ASCII free format file that contains variable and time step information that pertains to a Particular geometry file. The following information is included in this file: Number of scalar variables Number of vector variables Number of time steps Starting file number extension and skip-by value Flag that specifies whether there is changing geometry Names of the files that contain the values of scalar and vector variables The names of the geometry files that will be used for the changing geometry. The format of the EnSight5 result file is as follows: Line 1 Contains the number of scalar variables, the number of vector variables and a geometry-changing flag. (If the geometry-changing flag is 0, the geometry of the model does not change over time. If it is 1, then there is connectivity changing geometry. If it is 2, then there is coordinate only changing geometry.) Line 2 Indicates the number of time steps that are available. Line 3 Lists the time that is associated with each time step. There must be the same number of values as are indicated in Line 2. This line can actually span several lines in the file. You do not have to have one very long line. Line 4 Specified only if more than one time step is indicated in Line 2. The two values on this line indicate the file extension value for the first time step and the offset between files. If the values on this line are 0 5, the first time step available has a subscript of 0, the second time step available has a subscript of 5, the third time step has a subscript of 10, and so on. Line 5 Contains the names of the geometry files that will be used for changing geometry. This line exists only if the flag on Line 1 is set to 1 or 2. The geometry file name must follow the EnSight5 wild card specification. Line 6 through Line [5+N] where N is the number of scalar variables specified in Line 1. List BOTH the file names AND variable description that correspond to each scalar variable. There must be a file name for each scalar variable that is specified in Line 1.

11-96

EnSight 7 User Manual

11.3 EnSight5 Result File Format

If there is more than one time step, the file name must follow the EnSight5 wild card specification. See Note below. Lines that follow the scalar variable files. List the file names that correspond to each vector variable. There must be a file name for each vector variable that is specified in Line 1. If there is more than one time step, the file name must follow the EnSight5 wild card specification. See Note below. Note The variable description is limited to 19 characters in the current release. Variable names must not start with a numeric digit and must not contain any of the following reserved characters: ( ) [ ] + @ space ! # * ^ $ / : ?

The generic format of a result file is as follows:

#_of_scalars #_of_vectors geom_chang_flag #_of_timesteps time1 time2 time3 ..... start_file_# skip_by_value geometry_file_name.geo** scalar0_file_name** description (19 characters max) scalar1_file_name** description . . . vector0_file_name** description (19 characters max) vector1_file_name** description .

EnSight5 Result File Example 1

The following example illustrates a result file specified for a non-changing geometry file with only one time step:
2 1 0 1 0.0 exone.scl0 pressure exone.scl1 temperature exone.dis0 velocity

EnSight5 Result File Example 2

This example illustrates a result file that specifies a connectivity changing geometry that has multiple time steps.
1 2 1 4 1.0 2.0 2.5 5.0 0 1 extwo.geom** pres.scl** pressure vel.dis** velocity grad.dis** gradient

The following files would be needed for example 2:

extwo.geom00 extwo.geom01 extwo.geom02 extwo.geom03 pres.scl00 pres.scl01 pres.scl02 pres.scl03 vel.dis00 vel.dis01 vel.dis02 vel.dis03 grad.dis00 grad.dis01 grad.dis02 grad.dis03

EnSight 7 User Manual

11-97

11.3 EnSight5 Variable File Format

EnSight5 Wild Card Name Specification

If multiple time steps are involved, the file names must conform to the EnSight5 wild-card specification. This specification is as follows: File names must include numbers that are in ascending order from beginning to end. Numbers in the files names must be zero filled if there is more than one significant digit. Numbers can be anywhere in the file name. When the file name is specified in the EnSight5 result file, you must replace the numbers in the file with an asterisk(*). The number of asterisks specified is the number of significant digits. The asterisk must occupy the same place as the numbers in the file names.

EnSight5 Variable File Format

Variables files have one description line followed by a value for each node. For a scalar file there is one value per node, while for vector files there are three values per node. The values must be written in the following floating point format (6 per line as shown in the examples below): From C: From FORTRAN: Line 1 This line is a description line. Line 2 through the end of the file contains the values at each node in the model. A generic example:
A description line *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** *.*****E+** 12.5e e12.5

format format

The format of a variables file is as follows:

EnSight5 Variable File Example 1

This example shows a scalar file for a geometry with seven defined nodes.
These are the pressure values for a 7 node geometry 1.00000E+00 2.00000E+00 3.00000E+00 4.00000E+00 5.00000E+00 6.00000E+00 7.00000E+00

EnSight5 Variable File Example 2

This example shows the vector file for a geometry with seven defined nodes.
These are the velocity values for a 7 node geometry 1.00000E+00 1.00000E+00 1.00000E+00 2.00000E+00 2.00000E+00 2.00000E+00 3.00000E+00 3.00000E+00 3.00000E+00 4.00000E+00 4.00000E+00 4.00000E+00 5.00000E+00 5.00000E+00 5.00000E+00 6.00000E+00 6.00000E+00 6.00000E+00 7.00000E+00 7.00000E+00 7.00000E+00

11-98

EnSight 7 User Manual

11.3 EnSight5 Measured/Particle File Format

EnSight5 Measured/Particle File Format

This file allows you to define Particle locations, sizes, etc. to display with the geometry. Typical uses are fuel droplets for combustion analysis or data derived from experiments on prototypes. The measured/Particle files consist of the following: Measured/Particle geometry file (referenced by the measured results file) Measured/Particle results file (the filename which is put into the Data Readers (Set) Measured field) Measured/Particle variables file (referenced by the measured results file) The format of the EnSight5 Measured/Particle geometry file is described below. Note that there is only one description line and there must be an ID for each measured point. Note also that the number of Particles can be different in each of the geometry file (if you have transient data), however, the number of values in each of the corresponding variable files must coincide, and the IDs of the Particles must be consistent in order to track the Particles at intermediate times or locations. The format of an EnSight5 Measured/Particle geometry file is as follows: Line 1 This line is a description line. Line 2 Indicates that this file contains Particle coordinates. The words particle coordinates should be entered on this line without the quotes. Line 3 Specifies the number of Particles. Line 4 through the end of the file. Each line contains the ID and the X, Y, and Z coordinates of each Particle. The format of this line is integer real real real written out in the following format: From C: From FORTRAN:
%8d%12.5e%12.5e%12.5e format i8, 3e12.5 format

A generic measured/Particle geometry file is as follows:

A description line particle coordinates #_of_Particles id xcoord ycoord zcoord id xcoord ycoord zcoord id xcoord ycoord zcoord . . .

EnSight 7 User Manual

11-99

11.3 EnSight5 Measured/Particle File Format

EnSight5 Measured Geometry/Particle File Example

The following illustrates an EnSight5 Measured Geometry/Particle file with seven points:
This is a simple ensight5 measured geometry/particle file particle coordinates 7 101 0.00000E+00 0.00000E+00 0.00000E+00 102 1.00000E+00 0.00000E+00 0.00000E+00 103 1.00000E+00 1.00000E+00 0.00000E+00 104 0.00000E+00 1.00000E+00 0.00000E+00 205 5.00000E-01 0.00000E+00 2.00000E+00 206 5.00000E-01 1.00000E+00 2.00000E+00 307 0.00000E+00 0.00000E+00-1.50000E+00

EnSight5 Measured/ Particle File Format

The format of the EnSight5 Measured/Particle results file is as follows: Line 1 Contains the number of scalar variables, the number of vector variables, and a measured geometry changing flag. If the measured geometry changing flag is 0, only one time step is indicated. Line 2 Indicates the number of available time steps. Line 3 Lists the time that is associated with each time step. The time step information does not have to coincide with the model time step information. This line can actually span several lines in the file. You do not have to have one very long line. Line 4 Specified only if Line 2 specifies more than one time step. The line contains two values; the first value indicates the file extension value for the first time step, and the second value indicates the offset between files. If this line contains the values 0 and 5, the first time step has a subscript of 0, the second of 5, the third of 10, and so on. Line 5 Contains the name of the measured geometry file. If there is more than one time step, the file name must follow the EnSight wild card specification. Line 6 through Line [5+N] where N is the number of scalar variables specified in Line 1. List the file names that correspond to each scalar variable. There must be a file name for each scalar variable that is specified in Line 1. If there is more than one time step, the file name must follow the EnSight wild card specification. Lines that follow the scalar variable files. List the names of the files that correspond to each vector variable. There

11-100

EnSight 7 User Manual

11.3 EnSight5 Measured/Particle File Format

must be a file name for each vector variable that is specified in Line 1. If there is more than one time step, the file name must follow the EnSight wild card specification. A generic EnSight5 Measured/Particle results file is as follows:
#_of_scalars #_of_vectors geom_chang_flag #_of_timesteps time1 time2 time3 ..... start_file_# skip_by_value measured_geom_file_name** scalar0_file_name** description scalar1_file_name** description . . . vector0_file_name** description vector1_file_name** description . . .

Measured/Particle Results File Example 1

This example illustrates an EnSight5 Measured/Particle result file that specifies a non-changing geometry with only one time step:
2 1 0 1 0.0 exone.geom exone.scl0 pressure exone.scl1 temperature exone.dis0 velocity

Measured/Particle Results File Example 2

This example illustrates an EnSight5 Measured/Particle result file that specifies a changing geometry with multiple time steps:
1 2 1 4 1.0 2.0 2.5 5.0 0 1 extwo.geom** pres.scl** pressure vel.dis** velocity grad.dis** gradient

The following files are needed for Example 2:

extwo.geom00pres.scl00vel.dis00 extwo.geom01pres.scl01vel.dis01 extwo.geom02pres.scl02vel.dis02 extwo.geom03pres.scl03vel.dis03 grad.dis00 grad.dis01 grad.dis02 grad.dis03

Measured /Particle Results Variable files

The EnSight5 Measured/Particle variable files referred to in the measured Results file follow the same format as EnSight5 Variable files. The number of values in each of these variable files must correspond properly to the number of Particles in the corresponding measured geometry files.

EnSight 7 User Manual

11-101

11.3 Writing EnSight5 Binary Files

Writing EnSight5 Binary Files

This section describes the EnSight5 binary files. This format is used to increase the speed of reading data into EnSight. A utility exists for converting EnSight5 ASCII files to EnSight5 binary filesit is called asciitobin5 and is found on the release tape under ensight/server/utilities/asciitobin5. For binary files, there is a header that designates the type of binary file. This header is: C Binary or Fortran Binary. This must be the first thing in the file. The format for the file is then essentially the same format as the ASCII format, with the following exceptions: The ASCII format puts the node and element ids on the same line as the corresponding coordinates. The BINARY format writes all node ids then all coordinates. The ASCII format puts all element ids of a type within a Part on the same line as the corresponding connectivity. The BINARY format writes all the element ids for that type, then all the corresponding connectivities of the elements. In all the descriptions of binary files that follow, the number on the left end of the line corresponds to the type of write of that line, according to the following code: 1. This is a write of 80 characters to the file: C example:
char buffer[80]; strcpy(buffer,C Binary); fwrite(buffer,sizeof(char),80,file_ptr);

FORTRAN:

character*80

buffer

buffer = Fortran Binary write(10) buffer

2. This is a write of a single integer: C example: FORTRAN:

fwrite(&num_nodes,sizeof(int),1,file_ptr); write(10) num_nodes

3. This is a write of an integer array:

C example: fwrite(node_ids,sizeof(int),num_nodes,file_ptr); FORTRAN:write(10) (node_ids(i),i=1,num_nodes)

4. This is a write of a float array: C example: fwrite(coords,sizeof(float),3*num_nodes,file_ptr); FORTRAN: write(10) ((coords(i,j),i=1,3),j=1,num_nodes) (Note: Coords is a single precision array, double precision will not work!) EnSight5 Binary Geometry File Format An EnSight5 binary geometry file contains information in the following order:

11-102

EnSight 7 User Manual

11.3 Writing EnSight5 Binary Files

(1) (1) (1) (1) (1) (1) (2) (3) (4) (1) (1) (1) (2) (3) (3) (1) (2) (3) (3)

(1) (1) (1) (2) (3) (3) (1) (2) (3) (3)

<C Binary/Fortran Binary> description line 1 description line 2 node id <given/off/assign/ignore> element id <given/off/assign/ignore> coordinates #_of_points [point_ids] coordinate_array part # description line element_type #_of_element_type [element_ids] for the element_type connectivities for the element_type element_type #_of_element_type [element_ids] for the element_type connectivities for the element_type . . . part # description line element_type #_of_element_type [element_ids] for the element_type connectivities for the element_type element_type #_of_element_type [element_ids] for the element_type connectivities for the element_type . . .

Binary Scalar

An EnSight5 binary scalar file contains information in the following order: (1) description line (4) scalar_array

Binary Vector

An EnSight5 binary vector file contains information in the following order: (1) description line (4) vector_array

Binary Measured

An EnSight5 binary measured/Particle geometry file contains information in the following order:

EnSight 7 User Manual

11-103

11.3 Writing EnSight5 Binary Files

(1) (1) (1) (2) (3) (4)

<C Binary/Fortran Binary> description line 1 particle coordinates #_of_points point_ids coordinate_array

11-104

EnSight 7 User Manual

11.4 FAST UNSTRUCTURED Results File Format

11.4 FAST UNSTRUCTURED Results File Format

FAST UNSTRUCTURED input data consists of the following: Geometry file (required) (GRID file). Results file (optional). EnSight5 Measured/Particle Files (optional). The measured .res file references the measured geometry and variable files. FAST UNSTRUCTURED data files can be read as: Workstation: ASCII, C Binary, or FORTRAN binary Cray: ASCII, C Binary, or COS-Blocked FORTRAN binary Due to the different number of representations on a Cray Research vector system and workstations, binary files created on a Cray Research vector system can not be read on the workstation, and visa versa. EnSight reads the geometry (grid files) directly. However, an EnSight-like results file is needed in order to read the results unless a standard Q-file is provided in its place. See FAST UNSTRUCTURED Result File below.
FAST UNSTRUCTURED Geometry file notes

Only the single zone format can be read into EnSight. Any tetrahedral elements will be placed into the first domain Part. Triangular elements are placed into Parts based on their tag value. The FAST UNSTRUCTURED solution file or function file formats can be used for variable results. The I J K values need to be I=Number of points and J=K=1. This does require the use of a modified EnSight results file as explained below. Node and element numbers are assigned sequentially allowing for queries to be made within EnSight. Tetrahedron elements will be assigned before triangular elements.
FAST UNSTRUCTURED Result file format

The FAST UNSTRUCTURED result file was defined by CEI and is very similar to the EnSight results file and contains information needed to relate variable names to variable files, step information, etc. There is a slight variation from the normal EnSight results file because of the differences between the solution (Q file) and function files. The difference lies on the lines which relate variable filenames to a description. These lines have the following format:
<filename> <type> <number(s)> <description>

See FAST UNSTRUCTURED Result File below for the definition of each. The following information is included in a FAST UNSTRUCTURED result file: Number of scalar variables Number of vector variables Number of time steps

EnSight 7 User Manual

11-105

11.4 FAST UNSTRUCTURED Results File Format

Starting file number extension and skip-by value Flag that specifies whether there is changing geometry. Names of the files that contain the values of scalar and vector variables. An indication as to the type of the file being used for the variable, which variable in the file and the name given to that variable. The names of the geometry files that will be used for the changing geometry.
Generic FAST UNSTRUCTURED Result File Format

The format of the Result file is as follows: Line 1 Contains the number of scalar variables, the number of vector variables and a geometry changing flag. If the geometry changing flag is 0, the geometry of the model does not change over time. If the flag is 1, the geometry can change connectivity. If the flag is 2, only coordinates can change. Line 2 Indicates the number of time steps that are available. If this number is positive, then line 3 information must be present. If this number is negative, then Line 3 information must not be present and the times will be read from the solution file. Thus, one must have a solution file in one of the lines from Line 6 on. Line 3 Lists the time that is associated with each time step. There must be the same number of values as are indicated in Line 2. This line can actually span several lines in the file. Specify only if Line 2 value is positive. Line 4 Specified only if more than one time step is indicated in Line 2. The two values on this line indicate the file extension value for the first time step and the offset between files. If the values on this line are 0 5, the first time step available has a subscript of 0, the second time step available has a subscript of 5, the third time step has a subscript of 10, and so on. Line 5 This line exists only if the changing geometry flag on Line 1 has been set to 1 or 2. Line contains name of the FAST UNSTRUCTURED grid file. The file name must follow the EnSight wild card specification. Line 6 through Line [5+N] where N is the number of scalar variables specified in Line 1. List the file names that correspond to each scalar variable. There must be a file name for each scalar variable that is specified in Line 1. If there is more than one time step, the file name must follow the EnSight wild card specification. These lines also contain the type of file being used, solution or function, and the location of the variable value in the file. The contents are:
11-106 EnSight 7 User Manual

11.4 FAST UNSTRUCTURED Results File Format <filename> <type> <number> <description>

where filename is the name of solution file or function file containing the variable; type is S for solution file, or F for function file; numberis which variable in the file to use (specify just one number); and description is the Description of the variable. The solution file (s) is the traditional .q file in which normally the first variable is density, the second through fourth variables are the components of momentum, and the fifth variable is total energy. Lines that follow the scalar variable files. List the file names that correspond to each vector variable. There must be a file name for each vector variable that is specified in Line 0. If there is more than one time step, the file name must follow the EnSight wild card specification. These lines also contain the type of file being used, solution or function, and the location(s) of the variable values in the file. The contents are:
<filename> <type> <numbers> <description>

where filename is the name of solution file or function file containing the variable; type is S for solution file, or F for function file; numbersare which variables in the file to use (specify just three numbers); and description is the Description of the variable. The generic format of the result file is as follows:
#_of_scalars #_of_vectors geom_chng_flag #_of_timesteps time1 time2 time3 ..... start_file_# skip_by_value geometry_file_name.geo** scalar0_file_name** type # description scalar1_file_name** type # description . . . vector0_file_name** type # # # description vector1_file_name** type # # # description . . .

FAST UNSTRUCTURED This example illustrates a result file that specifies a non-changing geometry with Example only one time step.
3 2 0 1 0.0 block.sol block.sol block.scl block.var block.sol

S S F F S

1 5 1 1 2

Density Total_Energy Temperature 2 3 Displacement 3 4 Momentum

Thus, this model will get two scalars from the solution file (block.sol). The first is Density in the first location in the file and the next is Total energy in the fifth

EnSight 7 User Manual

11-107

11.4 FAST UNSTRUCTURED Results File Format

location in the solution file. It will also get a Temperature scalar from the first location in the function file (block.scl). It will get a Displacement vector from the function file called block.var. The three components of this vector are in the 1st, 2nd, and 3rd locations in the file. Finally, a Momentum vector will be obtained from the 2nd, 3rd, and 4th locations of the solution file. Example 2 is somewhat similar, except that it is transient, with coordinate changing geometry. Note also that the times will come from the solution file.
3 2 2 -10 0 1 block***.grid block***.sol S block***.sol S block***.scl F block***.var F block***.sol S

1 5 1 1 2

Density Total_Energy Temperature 2 3 Displacement 3 4 Momentum

11-108

EnSight 7 User Manual

11.5 FLUENT UNIVERSAL Results File Format

11.5 FLUENT UNIVERSAL Results File Format

This section describes the FLUENT results file format and provides an example of this file. For transient cases, you must supply this result file. For static models this file is not required. The FLUENT result file is a slightly modified EnSight5 results file and provides a way to describe multiple time-step FLUENT Universal files to EnSight. When using multiple FLUENT files with this result file definition, you must make sure that the files contain the same defined variables. In other words, any variable that exists in one must exist in all. The Result file is an ASCII free format file that contains time step and universal file information for each available time step. The following information is included in this file: Number of time steps Simulation Time Values Starting file number extension and skip-by value Name of the universal file with EnSight wild card specification. The format of the Result file is as follows: Line 1 Indicates the number of time steps that are available. Line 2 Lists the time that is associated with each time step. There must be the same number of values as are indicated in Line 1. This line can actually span several lines in the file. You do not have to have one very long line. Line 3 Specified only if more than one time step is indicated in Line 1. The two values on this line indicate the file extension value for the first time step and the offset between files. If the values on this line are 0 5, the first time step available has a subscript of 0, the second time step available has a subscript of 5, the third time step has a subscript of 10, and so on. Line 4 Contains the names of the universal file that will be used for the changing time step information. The universal file name must follow the EnSight5 wild card specification.

The generic format of the result file is as follows:

#_of_timesteps time1 time2 time3 ..... start_file_# skip_by_value universal_file_name***

EnSight 7 User Manual

11-109

11.5 FLUENT UNIVERSAL Results File Format

FLUENT Example

This example illustrates a FLUENT result file

4 1.0 2.0 3.0 4.0

01
extwo**.uni

The following FLUENT universal files will need to exist for the result file:
extwo00.uni extwo01.uni extwo02.uni extwo03.uni

11-110

EnSight 7 User Manual

11.6 Movie.BYU Results File Format

11.6 Movie.BYU Results File Format

For transient cases, you must supply an EnSight result file. The result file for the Movie.BYU case is exactly the same as for EnSight5 (it is repeated below for your ease). The Result file is an ASCII free format file that contains variable and time step information that pertains to a Particular geometry file. The following information is included in this file: Number of scalar variables Number of vector variables Number of time steps Starting file number extension and skip-by value Flag that specifies whether there is changing geometry Names of the files that contain the values of scalar and vector variables The names of the geometry files that will be used for the changing geometry. The format of the Movie.BYU (EnSight5) result file is as follows: Line 1 Contains the number of scalar variables, the number of vector variables and a geometry-changing flag. (If the geometry-changing flag is 0, the geometry of the model does not change over time. If it is 1, then there is connectivity changing geometry. If it is 2, then there is coordinate only changing geometry.) Line 2 Indicates the number of time steps that are available. Line 3 Lists the time that is associated with each time step. There must be the same number of values as are indicated in Line 2. This line can actually span several lines in the file. You do not have to have one very long line. Line 4 Specified only if more than one time step is indicated in Line 2. The two values on this line indicate the file extension value for the first time step and the offset between files. If the values on this line are 0 5, the first time step available has a subscript of 0, the second time step available has a subscript of 5, the third time step has a subscript of 10, and so on. Line 5 Contains the names of the geometry files that will be used for changing geometry. This line exists only if the flag on Line 1 is set to 1 or 2. The geometry file name must follow the EnSight5 wild card specification. Line 6 through Line [5+N] where N is the number of scalar variables specified in Line 1.
EnSight 7 User Manual 11-111

11.6 Movie.BYU Results File Format

List BOTH the file names AND variable description that correspond to each scalar variable. There must be a file name for each scalar variable that is specified in Line 1. If there is more than one time step, the file name must follow the EnSight5 wild card specification. See Note below. Lines that follow the scalar variable files. List the file names that correspond to each vector variable. There must be a file name for each vector variable that is specified in Line 1. If there is more than one time step, the file name must follow the EnSight5 wild card specification. See Note below. Note The variable description is limited to 19 characters in the current release. Variable names must not start with a numeric digit and must not contain any of the following reserved characters: ( ) [ ] + @ space ! # * ^ $ / : ?

The generic format of a result file is as follows:

#_of_scalars #_of_vectors geom_chang_flag #_of_timesteps time1 time2 time3 ..... start_file_# skip_by_value geometry_file_name.geo** scalar0_file_name** description (19 characters max) scalar1_file_name** description . . . vector0_file_name** description (19 characters max) vector1_file_name** description .

Movie.BYU Result File Example 1

The following example illustrates a result file specified for a non-changing geometry file with only one time step:
2 1 0 1 0.0 exone.scl0 pressure exone.scl1 temperature exone.dis0 velocity

Movie.BYU Result File Example 2

This example illustrates a result file that specifies a connectivity changing geometry that has multiple time steps.
1 2 1 4 1.0 2.0 2.5 5.0 0 1 extwo.geom** pres.scl** pressure vel.dis** velocity grad.dis** gradient

The following files would be needed for example 2:

11-112

EnSight 7 User Manual

11.6 Movie.BYU Results File Format extwo.geom00 extwo.geom01 extwo.geom02 extwo.geom03 pres.scl00 pres.scl01 pres.scl02 pres.scl03 vel.dis00 vel.dis01 vel.dis02 vel.dis03 grad.dis00 grad.dis01 grad.dis02 grad.dis03

EnSight 7 User Manual

11-113

11.7 PLOT3D Results File Format

11.7 PLOT3D Results File Format

PLOT3D input data consists of the following: Geometry file (required) (GRID file). Results file (optional). EnSight5 Measured/Particle Files (optional). The measured .res file references the measured geometry and variable files. PLOT3D data files can be read as: Workstation: ASCII, C Binary, or FORTRAN binary Cray: ASCII, C Binary, or COS-Blocked FORTRAN binary (see PLOT3D Reader, in Section 2.1) Due to the different number of representations on a Cray Research vector system and workstations, binary files created on a Cray Research vector system can not be read on the workstation, and visa versa. EnSight attempts to ensure that the format of the file being read matches the format you have selected in the Data Reader dialog. However, if you specify that the file is C binary, and it is really FORTRAN binary, this will not be detected and erroneous values will be loaded. EnSight reads the geometry (xyz files) directly. However, an EnSight-like results file (described below) is needed in order to read the results, unless a standard Qfile is provided in its place. PLOT3D Geometry file notes The following information is required in order to read PLOT3D files correctly: 1. whether there is Iblanking information in the file 2. whether files are in ASCII, C Binary, or FORTRAN binary 3. whether the file is Single Zone or Multi-Zoned 4. whether the model is 1D, 2D, or 3D in nature. Iblanking can be one of the following: 0 = Outside (Blanked Out) 1 = Inside 2 = Interior boundaries <0 = zone that neighbors If single zone with Iblanking, you can build EnSight Parts from the inside portions, blanked-out portions, or internal boundary portions. If single zone, you can also specify I, J, K limiting ranges for Parts to be created. If Multi-zoned with Iblanking, you can additionally build Parts that are the boundary between two zones. (For boundary you must specify exactly two zones.) If Multi-zoned and not using the between boundary option, a Part can span several zones.
11-114 EnSight 7 User Manual

11.7 PLOT3D Results File Format

If Multi-zoned, the dimension of the problem is forced to be 3D. There can be nodes in different zones which have the same coordinates. No attempt has been made to merge these. Thus, on shared zone boundaries, there will likely be nodes on top of nodes. One negative effect of this is that node labels will be on top of each other. Currently EnSight only prints out the global conditions in the solution file, fsmach, alpha, re, and time. It does not do anything else with them. Node and element numbers are assigned in a sequential manner. Queries can be made on these node and element numbers or on nodes by I, J, and K.

PLOT3D Result file format

The PLOT3D result file was defined by CEI and is very similar to the EnSight results file and contains information needed to relate variable names to variable files, step information, etc. There is a slight variation from the normal EnSight results file because of the differences between the solution (Q file) and function files. The difference lies on the lines which relate variable filenames to a description. These lines have the following format:
<filename> <type> <number(s)> <description>

See PLOT3D Result File below for the definition of each. The following information is included in a PLOT3D result file: Number of scalar variables Number of vector variables Number of time steps Starting file number extension and skip-by value Flag that specifies whether there is changing geometry. Names of the files that contain the values of scalar and vector variables. An indication as to the type of the file being used for the variable, which variable in the file and the name given to that variable. The names of the geometry files that will be used for the changing geometry.

Generic PLOT3D Result File Format

The format of the Result file is as follows: Line 1 Contains the number of scalar variables, the number of vector variables and a geometry changing flag. If the geometry changing flag is 0, the geometry of the model does not change over time. Only the coordinates can change for a PLOT3D file at present time. Line 2 Indicates the number of time steps that are available.

EnSight 7 User Manual

11-115

11.7 PLOT3D Results File Format

Line 3 Lists the time that is associated with each time step. There must be the same number of values as are indicated in Line 2. This line can actually span several lines in the file. Line 4 Specified only if more than one time step is indicated in Line 2. The two values on this line indicate the file extension value for the first time step and the offset between files. If the values on this line are 0 5, the first time step available has a subscript of 0, the second time step available has a subscript of 5, the third time step has a subscript of 10, and so on. Line 5 This line exists only if the changing geometry flag on Line 1 has been set to 1. Line contains name of the PLOT3D xyz file. The file name must follow the EnSight wild card specification. Line 6 through Line [5+N] where N is the number of scalar variables specified in Line 1. List the file names that correspond to each scalar variable. There must be a file name for each scalar variable that is specified in Line 1. If there is more than one time step, the file name must follow the EnSight wild card specification. These lines also contain the type of file being used, solution or function, and the location of the variable value in the file. The contents are:
<filename> <type> <number> <description>

where filename is the name of solution file or function file containing the variable; type is S for solution file, or F for function file; numberis which variable in the file to use (specify just one number); and description is the Description of the variable. The solution file (s) is the traditional .q file in which normally the first variable is density, the second through fourth variables are the components of momentum, and the fifth variable is total energy. Lines that follow the scalar variable files. List the file names that correspond to each vector variable. There must be a file name for each vector variable that is specified in Line 1. If there is more than one time step, the file name must follow the EnSight wild card specification. These lines also contain the type of file being used, solution or function, and the location(s) of the variable values in the file. The contents are:
<filename> <type> <numbers> <description>

where filename is the name of solution file or function file containing the variable; type is S for solution file, or F for function file; numbersare which variables in the file to use (specify just three numbers); and description is the Description of the variable.

11-116

EnSight 7 User Manual

11.7 PLOT3D Results File Format

The generic format of the result file is as follows:

#_of_scalars #_of_vectors geom_chng_flag #_of_timesteps time1 time2 time3 ..... start_file_# skip_by_value geometry_file_name.geo** scalar0_file_name** type # description scalar1_file_name** type # description . . . vector0_file_name** type # # # description vector1_file_name** type # # # description . . .

PLOT3D Example

This example illustrates a result file that specifies a non-changing geometry with only one time step.
3 2 0 1 0.0 block.sol block.sol block.scl block.var block.sol

S S F F S

1 5 1 1 2

Density Total_Energy Temperature 2 3 Displacement 3 4 Momentum

Thus, this model will get two scalars from the solution file (block.sol). The first is Density in the first location in the file and the next is Total energy in the fifth location in the solution file. It will also get a Temperature scalar from the first location in the function file (block.scl). It will get a Displacement vector from the function file called block.var. The three components of this vector are in the 1st, 2nd, and 3rd locations in the file. Finally, a Momentum vector will be obtained from the 2nd, 3rd, and 4th locations of the solution file. Vectors can be 1D, 2D, or 3D. For a vector, always provide three numbers, but a zero will indicate that a component is empty, thus:
block.var F 1 0 3 XZ_Displacement

would be a 2D vector variable with components only in the XZ plane. If the above example was transient, with 3 time steps, it would appear as:
3 2 0 3 0.0 1.5 4.0

11
block.sol** block.sol** block.scl** block.var** block.sol** S S F F S 1 5 1 1 2 Density Total_Energy Temperature 2 3 Displacement 3 4 Momentum

EnSight 7 User Manual

11-117

11.7 PLOT3D Results File Format

The files needed would then be:

block.sol01 block.sol02 block.sol03 block.scl01 block.scl02 block.scl03 block.var01 block.var02 block.var03

Note: A standard Q-file can be substituted for PLOT3D result file format if desired. A standard Q-file has 5 variable components (First is density, then the three components of momentum, and last is energy).

11-118

EnSight 7 User Manual

11.8 Server-of-Server Casefile Format

11.8 Server-of-Server Casefile Format

EnSight7 (with gold license key) has the capability of dealing with partitioned data in an efficient distributed manner by utilizing what we call a server-of-servers (SOS for short). An SOS server resides between a normal client and a number of normal servers. Thus, it appears as a normal server to the client, and as a normal client to the various normal servers.

This arrangement allows for distributed parallel processing of the various portions of a model, and has been shown to scale quite well. Please recognize that your data must be partitioned in some manner (hopefully in a way that will be reasonably load balanced) in order for this approach to be useful. (Included in the EnSight distribution is an unsupported utility that will take most EnSight Gold binary datasets and partition it for you. The source for this utility (called chopper) can be found in the $ENSIGHT7_HOME/ensight73/ unsupported/partitioner directory.) Note: If you do your own partitioning of data into EnSight6 or EnSight Gold format, please be aware that each part must be in each partition - but, any given part can be empty in any given partition. (All that is required for an empty part is the part line, the part number, and the description line.) You should place each partitioned portion of the model on the machine that will compute that portion. Each partitioned portion is actually a self contained set of EnSight data files, which could typically be read by a normal client - server session of EnSight. For example, if it were EnSight gold format, there will be a casefile and associated gold geometry and variable results file(s). On the machine where the EnSight SOS will be run, you will need to place the sos casefile. This is a simple ascii file which informs the SOS about pertinent information need to run a server on each of the machines that will compute the various portions.

EnSight 7 User Manual

11-119

11.8 Server-of-Server Casefile Format

The format for this file is as follows: (Note that [ ] indicates optional information, and a blank line or a line with # in the first column are comments.) FORMAT type: master_server datatype
where:

(Required) (Required)

datatype is required and is one of the formats of EnSights internal readers. gold n3s abaqus ensight6 estet fastunst ensight5 mpgs4 fluent plot3d movie fidap ansys

or it can be any other string to use the user-defined format. Note: the user-defined format declared to the SOS will be used by all servers. If datatype is blank, it will default to EnSight6 data type.

SERVERS number of servers: num

(Required) (Required)

where: num is the number of servers that will be started and run concurrently.

#Server 1 machine id: mid

(Comment only) (Required)

where: mid is the machine id of the server.

executable: /.../ensight7.server (Required, must use full path) [directory: wd] (Optional)
where: wd is the working directory from which ensight7.server will be run

[login id: id] [data_path: /.../dd]

(Optional)
where: id is the login id. Only needed if if is different on this machine.

(Optional)

where: dd is the data where the data resides. Full path must be provided if you use this line.

casefile: yourfile.case [resfile: yourfile.res] [measfile: yourfile.mea] #Server 2

(Required, but depending on format, may vary as to whether it is a casefile, geometry file, neutral file, universal file, etc.) (Depends on format as to whether required or not) (Depends on format as to whether required or not) (Comment only)

--- Repeat pertinent lines for as many servers as declared to be in this file ---

11-120

EnSight 7 User Manual

11.8 Server-of-Server Casefile Format

Example

This example deals with a EnSight Gold dataset that has been partitioned into 3 portions, each running on a different machine. The machines are named joe, sally, and bill. The executables for all machines are located in similar locations, but the data is not. Note that the optional data_path line is used on two of the servers, but not the third. FORMAT type: master_server gold SERVERS number of servers: 3 #Server 1 machine id: joe executable: /usr/local/bin/ensight73/bin/ensight7.server data_path: /usr/people/john/data casefile: portion_1.case #Server 2 machine id: sally executable: /usr/local/bin/ensight73/bin/ensight7.server data_path: /scratch/sally/john/data casefile: portion_2.case #Server 3 machine id: bill executable: /usr/local/bin/ensight73/bin/ensight7.server casefile: /scratch/temp/john/portion_3.case If we name this example sos casefile - all.sos, and we run it on yet another machine - one named george, you would want the data distributed as follows: On george: all.sos On joe (in /usr/people/john/data): portion_1.case, and all files referenced by it. On sally (in /scratch/sally/john/data): portion_2.case, and all files referenced by it. On bill (in /scratch/temp/john): portion_3.case, and all file referenced by it. By starting EnSight with the -sos command line option (which will autoconnect using ensight7.sos instead of ensight7.server), or by manually running ensight7.sos in place of ensight7.server, and providing all.sos as the casefile to read in the Data Reader dialog - EnSight will actually start three servers and compute the respective portions on them in parallel. Additional Note: The initial EnSight SOS provided with release 7.2 does not yet support all EnSight features. The basics of reading and creating parts, coloring by variables, clips, isosurfaces and cuts are provided. Most query, plotting, and other features are not. If you try to use a not-yet-implemented feature, you will receive a message that it isnt supported or the desired action will simply not occur. In a future release of EnSight, all features should be supported.

EnSight 7 User Manual

11-121

11.9 Periodic Matchfile Format

11.9 Periodic Matchfile Format

This is an optional file which can be used in conjunction with models which have rotational or translational computational symmetry (or periodic boundary conditions). It is invoked in the GEOMETRY section of the EnSight casefile, using the match: filename line. (see Section , EnSight6 Case File Format). When a model piece is created with periodic boundary conditions, there is usually a built-in correspondence between two faces of the model piece. If you transform a copy of the model piece properly, face 1 of the copy will be at the same location as face 2 of the original piece. It is desirable to know the corresponding nodes between face 1 and face 2 so border elements will not be produced at the matching faces. This correspondence of nodes can be provided in a periodic match file as indicated below. (Please note that if a periodic match file is not provided, by default EnSight will attempt to determine this correspondence using a float hashing scheme. This scheme has been shown to work quite well, but may not catch all duplicates. The user has some control over the capture accuracy of the hashing through the use of the command: test: float_hash_digits. If this command is issued from the command dialog, the user can change the number of digits, in a normalized scheme, to consider in the float hashing. The lower the number of digits, the larger the capture distance, and thus the higher the number of digits, the smaller the capture distance. The default is 4, with practical limits between 2 and 7 or 8 in most cases.) The transformation type and delta value are contained in the file. The periodic match file is an ASCII free format file. For unstructured data, it can be thought of as a series of node pairs, where a node pair is the node number of face 1 and its corresponding node number on face 2. For structured blocks, all that is needed is an indication of whether the i, j, or k planes contain the periodic face. The min plane of this direction will be treated as face 1, and the max plane will be treated as face 2. The file format is as follows:
rotate / translate theta / dx dy dz np n11 n21 n12 . . . n1np n22 . . . n2np

The first line is either rotate or translate The second line contains rotation angle in degrees or the three translational delta values. If any unstructured pairs, the third line contains the the number of these pairs (np). And the node ids of each pair follow. (The first subscript indicates face, the second is pair.)

blocks bmin bmax i/j/k

Last in the file comes as many of these blocks lines as needed. bmin and bmax are a range of block numbers. For a single block, b min and bmax would be the same. Only one of i, j, or k can be specified for a given block.

11-122

EnSight 7 User Manual

11.9 Periodic Matchfile Format

Simple unstructured rotational example:

Original 9 face 2 88 6 6 4 face 1
Figure 2-4 Model Duplication by rotational symmetry

7 5 3

2 2

The periodic match file for a rotation of this model about point 1 would be:
rotate 45.0 3 1 1 2 8 3 9

Thus, face 1 of this model is made up of nodes 1, 2, and 3 and face 2 of this model is made up of nodes 1, 8, and 9. So there are 3 node pairs to define, with node 1 corresponding to node 1 after a copy is rotated, node 2 corresponding to node 8, and node 3 corresponding to node 9. Simple structured translational model:
J block 1 I

2.0

J block 2

block 3

I Figure 2-5 Model Duplication by translational symmetry of structured blocks (3 instances)

translate 2.0 0.0 0.0 blocks 1 1 i blocks 2 3 j

EnSight 7 User Manual

11-123

11.9 Periodic Matchfile Format

Since block 1 is oriented differently than blocks 2 and 3 in terms of ijk space, two blocks lines were needed in the match file. Special Notes / Limitations: 1. This match file format requires that the unstructured node ids of the model be unique. This is only an issue with EnSight Gold unstructured format, since it is possible with that format to have non-unique node ids. 2. The model instance (which will be duplicated periodically) must have more than one element of thickness in the direction of the duplication. If it has only one element of thickness, intermediate instances will have all faces removed. If you have this unusual circumstance, you will need to turn off the shared border removal process, as explained in note 3. 3. The shared border removal process can be turned off, thereby saving some memory and processing time, by issuing the test: rem_shared_bord_off command in the command dialog. The effect of turning it off will be that border elements will be left between each periodic instance on future periodic updates. 4. The matching and hashing processes actually occur together. Thus, matching information does not have to be specified for all portions of a model. If no matching information is specified for a given node, the hashing process is used. By the same token, if matching information is provided, it is used explicitly as specified - even if it is has been specified incorrectly.

11-124

EnSight 7 User Manual

11.10 XY Plot Data Format

11.10XY Plot Data Format

This file is saved using the Save section of the Query Entity dialog. The file can contain one or more curves. The following is an example XY Data file:
Line Contents of Line

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

2 Distance vs. Temperature for Line Tool Distance Temperature 1 5 0.0 4.4 1.0 5.8 2.0 3.6 3.0 4.6 4.0 4.8 Distance vs. Pressure for Line Tool Distance Pressure 2 4 0.00 1.2 0.02 1.1 0.04 1.15 0.06 1.22 3 1.10 1.30 1.12 1.28 1.14 1.25

Line 1 contains the (integer) number of curves in the file. Line 2 contains the name of the curve. Line 3 contains the name of the X-Axis. Line 4 contains the name of the Y-Axis. Line 5 contains the number of curve segments in this curve.

EnSight 7 User Manual

11-125

11.10 XY Plot Data Format

Line 6 contains the number of points in the curve segment. Lines 7-11 contain the X-Y information. Line 12 contains the name of the second curve. Line 13 contains the name of the X-Axis Line 14 contains the name of the Y-Axis Line 15 contains the number of curve segments in this curve. (For the second curve, the first segment contains 4 points, the second 3 points.)

11-126

EnSight 7 User Manual