Scribd
Upload
68 views1 page

SM-BB70 / BB51 / BB50: General Safety Information

Uploaded by

aufche
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
68 views1 page

SM-BB70 / BB51 / BB50: General Safety Information

Uploaded by

aufche
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

SI-1L60A-003-00

General Safety Information


WARNING
If the inner cover is not installed correctly, the axle may rust and become damaged, and the bicycle may fall over and serious injury may occur as a result. Obtain and read the service instructions carefully prior to installing the parts. Loose, worn or damaged parts may cause the bicycle to fall over and serious injury may occur as a result. We strongly recommend only using genuine Shimano replacement parts. Read these Technical Service Instructions carefully, and keep them in a safe place for later reference.

Specifications
Bottom Bracket
Model number SM-BB70 FC-M770 FC-M771-K FC-M665 FC-M660 FC-T661 SM-BB51 FC-M590 FC-M591 68, 73 mm 1.37 X 24 T.P.I. SM-BB50 FC-M545 FC-M543-K FC-M542 FC-M533-K FC-M532

Applicable front chainwheel

Bottom bracket shell width Thread dimensions

Note
If the bottom bracket shell is not parallel, gear shifting performance will drop. Before riding the bicycle, check that there is no play or looseness in the connection. Also, be sure to retighten the crank arms and pedals at periodic intervals. If you feel any looseness in the bearings, the bottom bracket should be replaced. In addition, if pedaling performance does not feel normal, check this once more. Do not wash the bottom bracket with high-pressure jets of water. When installing the left and right adapters, be sure to install the inner cover too, otherwise the waterproofing performance will drop. Apply grease to the left and right adapters before installing them. Be sure to read the service instructions for the Front Drive System or the front chainwheel in conjunction with these service instructions. Parts are not guaranteed against natural wear or deterioration resulting from normal use. For maximum performance we highly recommend Shimano lubricants and maintenance products. For any questions regarding methods of installation, adjustment, maintenance or operation, please contact a professional bicycle dealer.

Installation of the adapter


Use the TL-FC32/36 special tool to install the right adapter (counterclockwise thread), the inner cover and the left adapter (clockwise thread).
Tightening torque : 35 - 50 Nm {305 - 435 in. lbs.}
Inner cover

Left hand adapter

Right hand adapter

For bracket type


Install as shown in the illustration.
Tightening torque : 35 - 50 Nm {305 - 435 in. lbs.}

Front Derailleur Front Chainwheel Bolt

Chain Device
When installing a BB mount-type chain device to a bicycle, refer to the table below to determine the number of spacers for the right side. If the thickness of the spacers used is not as given in the table, the front chainwheel may become loose and fall off, or problems with gear shifting may occur. When installing a BB mounttype chain device or a ISCG-type chain device to a bicycle, you need to be careful to avoid interference.
Adapter Adapter

Spacer installation method


The example in the illustration shows a BB mount-type chain device.

(1) Check whether the width of the bottom bracket shell is 68 mm or 73 mm. (2) Next, install the adapter while referring to the illustrations below.
68 / 73 mm

<Chain Device Thickness (BB mount)>


Model number Bottom bracket shell width 68 mm 2.5 mm x 1 73 mm Not needed 2.5 mm x 1 83 mm

<Normal type>
Spacer Bottom bracket shell width When using a band-type front derailleur When using a bracket-type front derailleur
(2.5mm) BB mounttype bracket

For chain device thickness of 2.5 mm

FC-M810-1 FC-M665 FC-M810-2 FC-M665 FC-M815-1 FC-M815-2

*
68 mm 2.5 mm x2
(2.5mm)

(1.8mm)

(0.7mm)

Model number

Bottom bracket shell width 68 mm Not needed 73 mm No available Not needed 83 mm

(2.5mm)

(2.5mm)

(2.5mm)

For chain device thickness of 5.0 mm

FC-M810-1 FC-M665 FC-M810-2 FC-M665 FC-M815-1 FC-M815-2

1.8 mm x1 0.7 mm x1 73 mm
(2.5mm)

When using in combination with the FD-M665-E


Model number FC-M665 FC-M810-2 FC-M815-2 68 mm Not needed

(2.5 mm chain device)


73 mm 83 mm

Bottom bracket shell width

* If using three 2.5 mm spacers with a band type and a bottom bracket shell having a width of 68 mm, install the three spacers so that there are two on the right and one on the left.

<Chain case specifications>


Spacer Bottom bracket shell width
Chaincase stay

No available Not needed

<Installation method>
Install the chain device and the front derailleur as shown in the illustration. If using in combination with an BB mounttype front derailleur, make sure that the chain device does not obstruct the BB mount-type bracket.

68 mm

F A

BB mount-type bracket

68 mm 2.5 mm x2 1.8 mm* x1


(2.5mm) (2.5mm) (0.7mm)

F A

Chain Device

0.7 mm x1 73 mm * 1.8 mm corresponds to the thickness of the chain case.

F A : 2.5 mm spacer

(0,7mm)

Technical Service Instructions

SI-1L60A-003
One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003 Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan

SM-BB70 / BB51 / BB50


00

Please note: specifications are subject to change for improvement without notice. (English) Feb. 2009 by Shimano Inc. XBC IZM Printed in Malaysia.

You might also like