Scribd
Upload
619 views

Conveyor Assembly Manual PDF

This document provides instructions for assembling a FlexLink conveyor system. It is divided into sections covering installation site preparation, tools and fasteners, cutting beams, assembly, and start-up and testing. The assembly section instructs to begin by assembling the support structure using feet, support beams, and beam connectors. It then provides detailed steps for mounting different types of feet to support beams using connecting strips, screws, and nuts.

Uploaded by

zaiayra71
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
619 views

Conveyor Assembly Manual PDF

This document provides instructions for assembling a FlexLink conveyor system. It is divided into sections covering installation site preparation, tools and fasteners, cutting beams, assembly, and start-up and testing. The assembly section instructs to begin by assembling the support structure using feet, support beams, and beam connectors. It then provides detailed steps for mounting different types of feet to support beams using connecting strips, screws, and nuts.

Uploaded by

zaiayra71
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 68
Conveyor assembly manual Table of contents Introduction About this manual Installation site preparations Tools Fasteners Cutting FlexLink beams Assembly. Introduction Feet, Beam connectors Conveyor beams. Drive units Idler units Slide rail and support rail Chain Guide rail system. Angle plates. Drip trays and drip catchers. Front piece. Final preparations Conveyor system XK XK pallet system Start-up and testing Safety considerations Slip clutch adjustment. Start-up. Troubleshooting, Introduction About this manual Introduction ‘The main purpose of this manual is to help selt-building end users, with litle or no prior experience, to assemble a FlexLink conveyor system. Each chapter includes detailed instructions and pic- tures showing how to assemble the different parts. Most pictures in the manual include parts from the XL con- veyor system, but all instructions are applicable to the XS, XL, XM, XH and XK systems unless otherwise noted. ‘Operations that apply only to the XK conveyor system are described in a separate chapter. Installation site preparations Document disposition ‘The document is divided into the following five main parts: ‘+ Installation site preparations + Tools and fasteners ‘+ Cutting FlexLink beams + Assembly + Start-up and testing Assembly planning Work systematically: 1. Prepare by studying your assembly drawing. 2 Ensure that the necessary tools are available. 3 Make sure you have all the materials and components needed to assemble the conveyor system. Check with the pars list. 4. Make sure you have enough floor space to mount the conveyor system. 5 Check to see if the floor at the installation site is even, so that all feet can be properly attached to the floor. Assembly order ‘The following list can be used as a checklist during your conveyor assembly work: ‘Activity ‘Starts on Connect feet and structural beams page 7 ‘Assemble conveyor beams and mount page 21 them on to the support structure Mount slide rail on to the conveyor beam page 26 Run a short piece of chain through the page 34 conveyor to check that there are no obstructions Mount guide rail, drip trays and other accessories on to the conveyor page 38 Read Final preparations at the end of this manual Go to page 55 for special information relating to con- veyor system XK page 54 2 Introduction 8 extn? Tools General tools To assemble a FlexLink conveyor, you will need most of the tools listed on the following pages. Not all are essen- tial, but they will make your assembly work easier and more efficicient. Hand tools 10 and 13 mm box wrench Cutters (for cutting slide rail) ‘Set of metic Allen keys Roller thread fluteless tap and tap wrench (M6 and M8) Countersink bit Tape measure In addition, the tools listed below can be useful: Files ‘Socket wrench ‘Screw-driver Pliers Knife (for cutting off plastic screw heads) Soft faced hammer ‘Clamp (for chain installation) Level Power tools Cross-cut circular saw for aluminium Hand drill Drillbit (for fixing of slide rail): XS:23,2 mm, XUXM/XHIXK: 24,2 mm FlexLink tools Rivet crimping pliers XS (9.3 mm): 3924776 XUXMIXH (4 mm): 3925800 “7 3 = as j Rivet crimping clamp XS (23 mm): 3924770 XUXMIXH (0 4 mm): 3923005 The riveting tools have replace- able pads. By replacing the pads you can use the same riveting tool for 3 mm and 4 mm rivets. Drill fixture for installation of slide rail XS (93.2 mm): 3924774 XUXMIXHIXK (© 4,2 mm): 3920500 ‘Mounting too! for slide rail XS/XL: XLMR 140 XM: XMMR 140 XH: XHMR 200 XK: XKMR 200 ‘Mounting toolkit for guide rail (XK) 3926757 Each kit is delivered with two tools. Pin insertion tool for chain XS/XL: XLMJ 4 XM: XMMJ 6 XH: XHMJ 6 XK: XKMJ 8 A, Guide rail bending machine 3922963 (not shown) Dail fixture for fastener yokes XCAD 18 ; “To dri or fastener yokes (page 17-18), the 10 mm drilinsert has to be removed. The dil insert is Secured by a locking screw With the stop tongue down, the fixture is inserted into the T-slot of the beam until stop, and then locked. The hole willbe driled 22 mm from the beam end and cen- tered by the fixture. Introduction 3

You might also like