JawaharlalNehruEngineeringCollege

LaboratoryManual

ELECTRICAL MACHINE & Instrumentation.

For Second Year (ECT/IE) Students

Manual made by Prof. M.V.Kunte

Author JNEC, Aurangabad.

FORWARD

It is my great pleasure to present this laboratory manual for second year engineering students for the subject of Electrical Machine & Instrumentation. Keeping in view the vast coverage required for visualization of concepts of Electrical Machines & Instrumentation. components. With simple language.

As a student, many of you may be wondering with some of the questions in your mind regarding the subject and exactly what has been tried is to answer through this manual.

Faculty members are also advised that covering these aspects in initial stage itself, will greatly relived them in future as much of the load will be taken care by the enthusiasm energies of the students once they are conceptually clear.

Prof.Dr.S.D.Deshmukh Principal

LABORATORY MANNUAL CONTENTS

This manual is intended for the second year students of Electronics Engineering and Industrial Electronics branch in the subject of Electrical Machine & Instrumentation This manual typically contains practical/Lab Sessions related electrical machine & Instrumentation covering various aspects related the subject to enhanced understanding.

Although, as per the syllabus, only descriptive treatment is prescribed, we have made the efforts to cover various aspects of electrical machine & Instrumentation subject covering types of different electrical machines, their operating principals, their characteristics and different sensors, Industrial panel meters & signal conditioning will be complete in itself to make it meaningful, elaborative understandable concepts and conceptual visualization.

Students are advised to thoroughly go through this manual rather than only topics mentioned in the syllabus as practical aspects are the key to understanding and conceptual visualization of theoretical aspects covered in the books.

Good Luck for your Enjoyable Laboratory Sessions

Prof.M.V.kunte

SUBJECT INDEX 1.Dos and Donts 2. Lab exercise: 1) To study speed control of d. c. shunt motor. 2) To perform load test on d. c. shunt motor. 3) To perform load test on 3 phase induction motor. 4) To study d. c. motor starter. 5) To study the induction motor starter. 6) To study of characteristics of transducer using thermocouple 7) To study Solar cell.

8) To study electronic security system. 3. 4. 5. Quiz on the subject Conduction of VivaVoce Examination Evaluation and Marking Systems

DOs and DONT DOs in Laboratory:

1. Understand the equipment to be tested and apparatus to be used . 2. Select proper type (i.e. A. c. or D. C.) and range of meters. 3. Do not touch the live terminals. 4. Use suitable wires (type and size). 5. All the connection should be tight. 1. Do not leave loose wires (i.e. wires not connected).

2. Get the connection checked before switching ON the supply. 3. Never exceed the permissible values of current, voltage, and / or speed of any machine, apparatus, wire, load, etc. 4. Switch ON or OFF the load gradually and not suddenly. 5. Strictly observe the instructions given by the teacher/Lab Instructor

Instruction for Laboratory Teachers:

1. Submission related to whatever lab work has been completed should be done during the next lab session. The immediate arrangements for printouts related to submission on the day of practical assignments. 2. Students should be taught for taking the observations /readings of different measuring instruments under the able observation of lab teacher. 3. The promptness of submission should be encouraged by way of marking and evaluation patterns that will benefit the sincere students.

2.LabExercises:
Exercise No1: ( 2 Hours) 1 Practical
Speedcontrolofad.c.shuntmotor.
AIM: to study the speed control of a d. c. shunt motor. a) by varying field current with armature voltage kept constant. b) By varying armature voltage with field current kept constant. APPARATUS:1) rheostat (100 1.2 amp) --------------------- 1no 2) Rheostat (100 6.0 amp)-------------------- 1no 3) D. c. voltmeter (0-300volt) -------------------1no. 4) D.C. Ammeter (0-1A) ------------------------- 1no

THEORY: 1.What is effect of voltage on D. C. shunt motor ? 2.What are different factors which affect the speed of D. C. shunt motor ? PROCEDURE: 1) Make the connections as per circuit dia. 2) Set up the field and armature rheostat to their maximum value. 3) Switch on the D.C. Supply start the motor with the help of starter. Adjust the field current to rated value. 4) Note the speed with the help of tachometer, the voltage across armature and the field current. 5) Change the speed by varying the rheostat in the armature circuit. Note the speed and armature voltage, the field current remaining constant. 6) Repeat steps 4. and 5. above, for different field currents. 7) Plot speed V/s armature voltage 8) Keep the rheostat in the armature circuit to some fixed value. Note the voltage across armature. Note the field current and speed. 9) Vary the field current. OBSERVATION TABLE:a) Armature voltage variation. 1) Field current (constant) = ____amps.

Sr. no. 1. 2.

Armature voltage (Va in volts)

Speed (r.p.m)

3. 4. 5. 6. b) Variable Field current 1) Armature voltage (constant) = _____volts.

Sr. no 1. 2. 3. 4. 5. 6.

Field current (If in amps)

Speed (r.p.m.)

GRAPH :

V O L T S

F I E L D C U R R E N T

SPEED

SPEED

CONSTANTFIELDCURRENT

CONCLUSION:The variation of speed with armature voltage and field current has been studied. The speed of d. c. Shunt motor is directly proportional to the armature voltage and inversely proportional to the field current. Thus, to increase speed above rated speed field current should be decreased & to decrease the speed below rated speed armature voltage should decrease.

Exercise No2: ( 2 Hours) 1 Practical

LoadtestonD.C.shuntmotor.
AIM- To perform load test on D.C. shunt motor APPARATUS1) Rheostat (570 ohm, l Amp ) ----------------------- 1 no 2) Rheostat (300 ohm, 1.7 amps) ---------------------1no. 3) D. c. voltmeter (0-10ohm) -------------------------2no. 4) D. c. voltmeter (0-300v) --------------------------2no 1) Tachometer. THEORY: 1.What is effect of load on D. C. shunt motor ? 2.What is the relation between efficiency & load of D. C. shunt motor ? 3.Why current & torque increases linearly with the load ?

PROCEDURE 1) Make the connection as per circuit dia. 2)Set the field rheostat of motor to zero and field rheostat of generator to maximum. 3)Switch on D.C. supply and start the motor with the help of starter. 4)Adjust field rheostat for motor to obtain rated speed. For one set of readings the setting of field rheostat should not be altered. 5) Adjust D.C. shunt generator voltage to its rated voltage with the help of its field rheostat. 6)Load the generator with keeping its terminal voltage constant. 7)Note the reading of ammeters, voltmeters and speed. 8)Repeat (6) and (7) above to a cover the range of no load to full load of motor. 9)Plot speed vs. output, armature current Vs output, efficiency Vs output, torque vs. output curves SAMPLE CALCULATIONEfficiency of generator is assumed as 87% Generator output Vg Ig watts. Generator input = generator output / 0.87 Generator input = motor output. Motor input Vm Im watts. % Motor efficiency = (motor output / motor input) * 100

Motor Torque = (motor output in watts) * 60 2n

N-M

OBSERVATION TABLE :

GENERATOR Sr.No. 1 2 3 4 5
GRAPH :

MOTOR Vm Im

Vg

Ig

SPEED (rpm)

MOTOR MOTOR EFFI. TORQUE I/P O/P OF (N.M) (watts) (watts) MOTOR

T O R Q U E

M O T O R C U R R E N T

O U T P U T

O U T P U T

T O R Q U E V s O U T P U T

M O T O R C U R R E N T V s O U T P U T

E F F I C I E N C Y

S P E E D

OUTPUT

O U T P U T

EFFICIENCYVsOUTPUT

S P E E D V sO U T P U T

CONCLUSIONFrom the above graphs, the motor current increases with the load, and the speed decreases slightly with increase in load. The efficiency initially increases with the load, and then reaches its maximum (at about 80 to 90 % of the full load) and then decreases.

Exercise No3: ( 2 Hours) 1 Practical

LoadTestOn3PhaseInductionMotor
AIM: To perform the load test on 3-Phase induction motor. APPARATUS: 1)Two-element wattmeter (10A, 500v) ---------------------1 No. 2)Ammeter (0-10A) ------------------------------------------1 No 3)Voltmeter (0-500v) ----------------------------------------1 No 4)Rheostat (500 ohm, 1.2A) ---------------------------------1 No 5)Ammeter D.C. (O-10A) ------------------------------------1 No 6)Voltmeter D.C. (0-300v) ----------------------------------1 No 7)Tachometer. THEORY: 1.What is effect of load on 3 phase Induction motor ? 2.What is the relation between speed & load of 3 phase Induction motor ? 3.Why current & torque increases linearly with the load ? 4.How power factor is affected by load ?

PROCEDURE: 1)Make the connection as per the circuit diagram. 2)Put the load switches off. Set generator field rheostat to maximum start the induction motor with the help of the start & run it to its normal speed. 3) Excite the dc shunt generator to its voltage. Note power input, to motor & the speed, with the generator not loaded. 4) Put some load on generator & Note the D.C. generator output, motor input and the speed. 5) Take the more readings by increasing the load gradually till the full load is reached. 6) Calculate & plot the graphs. Output Vs speed, Output Vs Efficiency, Output Vs motor current. Output Vs slip, output Vs P.F. OBSERVATION TABLE: sr. no 1. 2. 3. 4. 5. I. M. Vm in volts. Im in Amp Motor input Power in watts Speed in rpm Ig. I. M. Input watts %n Slip p.f.

GRAPH:

S P E E D

E F F I C I E N C Y

O U T P U T

O U T P U T

S PE E D V sO U TP U T

E F F IC IE N C Y V sO U T P U T

P O W E R F A C T O R

C U R R E N T

O U T P U T

O U T P U T

PO W E R FA C T O R V sO U T PU T

C U R R E N T V sO U T P U T

CONCLUSION: The speed falls, the power improves and the current increases, with as increase in output of motor. The efficiency increases and is maximum near full load.

Exercise No4: ( 2 Hours) 1 Practical

D.C.motorstarter
At starting, Eb =0 because speed of motor is zero. Armature current of motor is equal to, Ia = V- Eb / Ra so Ia =V/ Ra (Eb = 0) Since Ra is very small so motor will draw large armature current. To limit the armature current in safe value we add some external resistance in armature circuit. A mechanism which adds resistance during starting only is known as starter. THEORY There are two types of starters which are commonly used for d.c. shunt motor 1) 3-point starter 2) 4 - point starter 3- POINT STARTER Three point starter is shown in the figure 1, when motor is started, starting arm is moved slowly towards the ON position 1)As soon as arm touches the stud no. 1 full starting resistance get connected in the armature circuit. 1) Field current receives supply directly The starting armature current is equal to, Ia = V / (Ra + Rst) 2) The arm is moved against the spring force towards the ON position. 3) When the arm travels towards ON position , the starting resistance is gradually removed from armature circuit . since motor takes full speed, motor develops full back E.M.F. the starting arm carries a soft iron piece which is held by attraction of the hold on coil. starter remains in ON position because the electromagnetism formed by NO VOLT COIL FUNCTION OF HOLD ON (NO VOLT COIL) 1) In case of supply failure NO VOLT COIL gets de-energized and the starting arm will be released to OFF position. This is automatically done by spring action. 2) It hold the plunger in ON position 3) It gives the protection against field failure

FUNCTION OF OVERLOAD COIL Overload coil is a electromagnet connected in series with armature. when current exceeds beyond certain predetermined value the electromagnet will become strong and it attracts plunger. Due to this voltage across NO VOLT COIL becomes zero. this will make hold on coil de energized due to which arm gets to OFF position and motor gets disconnected from supply.

LIMITATIONS OF THREE POINT STARTER 1) When motor is in ON position the starting resistance gets remove form armature circuit at the same time it gets attached to field circuit, which is dangerous to the motor. 2) When we control speed of motor by field control method, resistance in field circuit reduces field current which increases the speed of motor at the same time there is chance under ON condition motor could disconnect from supply due to de energisation of HOLD ON COIL, due to less field current.

4- POINT STARTER 4- point starter with brass arc covers limitations of 3- point starter using brass arc covers first limitation. Making field circuit path independent of hold coil circuit by making forth point in addition with 3-point circuit covers second limitation. When field current is reduced while controlling speed of motor will not effect on magnetic field of hold on coil because circuit of hold coil is separate than field coil circuit as shown in the fig.2.

Exercise No5: ( 2 Hours) 1 Practical

InductionMotorStarter.
AIM: to study the Induction Motor Starter. THEORY: NESSCISITY OF STARTER: If normal supply voltage is applied to stationary motor then the motor takes very large initial current. Induction Motor when direct switched takes 5 to 7 times their full load current & develops only 1.5 to 2.5 times their full load torque. This will produce large line drop affect the operation of other electrical equipment connected in same circuit. Starters should be used for the motors of rating above 25 KW to 40KW. Types of starters generally used are as follows: For Squirrel-cage Motors: a. Direct on line starter. b. Primary Resister/Reactor Starter. c. Auto -transformer Starter. d. Star-Delta Starter. For Slip Ring Induction Motor a. Rotor Rheostat Starter. 1. DIRECT ON LINE STARTER: In this type of starter the triple pole single throw switch is used. By using that switch we can directly connect motor to full supply voltage. Hence it is known as Direct on line starter. This starter is used for the motors of the rating below 25 KW to 40 KW. Because the starting current drawn by the motor does not affect so much to the equipments which are connected to same line. 2. PRIMARY RESISTER/REACTOR STARTER: In this type of starter supply is given to stator through Resistor or reactor therefore it is called as primary resistor starter. Their purpose is to drop some voltage applied across the motor terminal, thus the initial current drawn by the motor is reduced. When motor attends 80% of the speed total resistance is cut out from circuit. 3. Auto Transformer Starter: In this starter the supply is given to stator through an Auto Transformer. This method is used for both star & delta connected motors. When the motor has run up to 80% of the full load speed, connections are so changed that autotransformers are cut out from the supply. The switching is done with air break or oil immersed switch.

1. STAR-DELTA STARTER: This starter is used for those motors, which are built to run normally with a delta connected stator winding. This starter uses the triple pole double throw switch which connects the stator winding of motor in star when it is in position One, and it connects the stator winding of motor in delta when it is in position Two. In the starting period the switch is kept in position One, so that the stator winding will be star connected & it has reduced voltage applied across it to limit the starting current. When motor attends 50% to 60% position of switch is changed to two i.e. stator winding of motor is connected in delta so that full supply voltage is applied across winding & motor will run as normal Induction Motor. 6. ROTOR RHEOSTAT STARTER: This starter is used for slip-ring Induction motor. In this motors full supply voltage is applied across stator & starting current is controlled by inserting star connected rheostat in rotor ckt. By using slip-rings. As Induction motor is same as transformer if we control rotor current automatically stator current get controlled. The star connected resistance being gradually cut out of the rotor circuit as motor gathers speed. Because of this rotor resistance during starting period power factor of motor is also improved as well as starting torque improved.

EXPERIMENT NO: 4

Aim: Apparatus:Theory:

To plot the characteristics of thermocouple.. Thermocouple, water pot, electric heater, stand, multimeter, Thermometer.

1)Principle: When two metals having different work function are placed together voltage is generated at the junction which is nearly proportional to the temperature. This junction is called thermocouple. The E.M.F. developed in circuit composed of two dissimilar metals with junction kept at absolute temperatures T1 and T2 with (T2>T1) may be approximately written as t=a(T1T2)+b(T1-T2)2 Where a and b are constants depending on metals used. Write details of following points. 2)Construction of Thermocouple. 3)Give different types of thermocouple with standard range 4)Sensitivity of thermocouple Procedure: 1) Make the connections of thermocouple terminals with multimeter. 2) Switch on the water heater and put the thermocouple and thermometer in the water pot. 3) Note the corresponding reading of thermometer as well as reading of multimeter at that temperature. Multimeter will give the voltage across the junction at that temperature. 4) Take 9-10 readings. Plot the graph .

Observation Table:

Sr. No. 1 2 3 4 5 6 7 8 9 10

Temperature in c

Emf in millivolts

Graph:
Plot the graph of Temperature (in c) Vs emf (in mv)

Conclusion: The graph of thermoelectric emf against rise in temperature is almost linear, i.e rise in e.m
.f. is directly proportional to the rise in temperature.

EXPERIMENT NO: 4

Aim: Apparatus:Theory:

To plot the characteristics of thermocouple.. Thermocouple, water pot, electric heater, stand, multimeter, Thermometer.

1)Principle: When two metals having different work function are placed together voltage is generated at the junction which is nearly proportional to the temperature. This junction is called thermocouple. The E.M.F. developed in circuit composed of two dissimilar metals with junction kept at absolute temperatures T1 and T2 with (T2>T1) may be approximately written as t=a(T1T2)+b(T1-T2)2 Where a and b are constants depending on metals used. Write details of following points. 2)Construction of Thermocouple. 3)Give different types of thermocouple with standard range 4)Sensitivity of thermocouple Procedure: 1) Make the connections of thermocouple terminals with multimeter. 2) Switch on the water heater and put the thermocouple and thermometer in the water pot. 3) Note the corresponding reading of thermometer as well as reading of multimeter at that temperature. Multimeter will give the voltage across the junction at that temperature. 4) Take 9-10 readings. Plot the graph .

Observation Table:

Sr. No. 1 2 3 4 5 6 7 8 9 10

Temperature in c

Emf in millivolts

Graph:
Plot the graph of Temperature (in c) Vs emf (in mv)

Conclusion: The graph of thermoelectric emf against rise in temperature is almost linear, i.e rise in e.m
.f. is directly proportional to the rise in temperature.

EXPERIMENT NO: 6

Aim: Apparatus:Theory:

To plot the characteristics of thermocouple.. Thermocouple, water pot, electric heater, stand, multimeter, Thermometer.

1)Principle: When two metals having different work function are placed together voltage is generated at the junction which is nearly proportional to the temperature. This junction is called thermocouple. The E.M.F. developed in circuit composed of two dissimilar metals with junction kept at absolute temperatures T1 and T2 with (T2>T1) may be approximately written as t=a(T1T2)+b(T1-T2)2 Where a and b are constants depending on metals used. Write details of following points. 2)Construction of Thermocouple. 3)Give different types of thermocouple with standard range 4)Sensitivity of thermocouple Procedure: 1) Make the connections of thermocouple terminals with multimeter. 2) Switch on the water heater and put the thermocouple and thermometer in the water pot. 3) Note the corresponding reading of thermometer as well as reading of multimeter at that temperature. Multimeter will give the voltage across the junction at that temperature. 4) Take 9-10 readings. Plot the graph .

Observation Table:

Sr. No. 1 2 3 4 5 6 7 8 9 10

Temperature in c

Emf in millivolts

Graph:
Plot the graph of Temperature (in c) Vs emf (in mv)

Conclusion: The graph of thermoelectric emf against rise in temperature is almost linear, i.e rise in e.m
.f. is directly proportional to the rise in temperature.

Exercise No7: ( 2 Hours) 1 Practical

Studyofsolarcells.
AIM: Study of solar cells. APPARATUS: Photo voltaic cells. SOLAR CELLS: The solar cells mainly consist of photovoltaic cell, which are grouped and electrically connected and packed, in one frame. Photovoltaic are nothing but the word implies (Photo = light and voltaic = electricity), these photovoltaic cells convert sunlight directly into electricity. WORKING: Photovoltaic cells are made up of special material celled semiconductors such as silicon, selenium etc. Basically, when light strikes the cell, a certain portion of it is absorbed within the semiconductor material used in a solar system. This means that the energy of the absorbed light is transferred to the semiconductor material. This energy knocks electrons loose, allowing them to flow freely. The PV cells used how one or more electric fields that act to force electrons freed by light absorption to flow in certain direction. This flow of electrons is a current and by placing metal contacts on the top and bottom of the PV cell, current can he drawn out and used externally. CONSTRUCTION OF SOLAR CELLS: A solar cell mainly consists of a semiconductor diode with p-n junction. The n (emitter) and p (base) regions are provided with ohmic contact to enable an electric current to flow through an external circuit (i.e.) load circuit. The front contact is grid that allows the loose electrons to flow in the electric circuit. An anti reflecting coating ensures that as much light as possible is absorbed into the cell so as to get it converted into electrical energy. The PV cells absorb photons. These photons raise the energy level of the electrons in the semi conducting materials, thus exciting some of the electron to jump the lower energy valence band to the

high - energy electron and the movement of holes in the opposite direction constitutes electric current. Conduction band. The electrons in the conduction band and the holes left behind in the valence band are mobile and are induced to move. The motion of electron and the movement of holes in the opposite direction constitute electric current.

Exercise No 8: ( 2 Hours) 1 Practical

Smokeoperatedalarm.
AIM :- Study of Smoke operated alarm. APPARATUS :1. Kit,

2. power supply, 3. connecting wires etc.

THEORY :Figure shows a socket of smoke operated alarm that works on light beam principle. Here the LDR is illuminated by a light beam and is wired in a bridge network formed by R1-R2-RV1 and LDR and bridge output is detected and used to provide gate driver to SCR. A transistor detector is used in circuit, circuit is adjusted so that bridge is closed to balance when LDR is normally illuminated and transistor Q is conducting slightly but not sufficiently to drive the SCR ON. When smoke enters light, light beam LDR illumination decreases and LDR resistance increases bridge goes out of balance in such a way that Q is triggered further ON. Thus causing SCR and alarm to turn ON. The socket then function as smoke operated alarm. When reset button is pressed, diode D1 is reverse biased. Reverse potential is applied across the alarm and it gets turn off. PROCEDURE :1. Make power ON to the unit. 2. Use incense stick to create smoke. 3. Keep enlighten incense stick from bottom side of sensor. 4. As smoke occupies chamber, alarm sounds. 5. To make alarm OFF first remove smoke from chamber and thus press RESET switch. CONCLUSION :When smoke enters into chamber, LDR resistance increases and causes SLR and alarm to turn ON. Thus it works as smoke alarm.

3.Quizonthesubject:

2.Speed control of D.C. Shunt motor a. What are the factors on which speed of D.C. Shunt motor depends? b. Name the different speed control methods. C. What is the disadvantage of armature rheostat method? d. What is the advantage of Ward Leonard method? e. Where the D.C. Shunt motor is applicable? 3.Load test on d. c. shunt motor. a. What is the purpose of Load test on d. c. shunt motors? b. What is the relation between Ia and Armature Cu loss? c. What are different losses in D.C. shunt motor. 2.Motor A. How energy conversion takes place in D C Generator. B. Why D C Motor is known as constant speed motor? C. Why starter is necessary for starting of D C motor? D. Explain the disadvantage of 3pt. Starter. E. How to reverse the direction of rotation of D C shunt Motor. F. What is the use of commutator & brushes in D C Motor?

4.ConductionofVivaVoceExaminations:
Teacher should oral exams of the students with full preparation. Normally, the objective questions with guess are to be avoided. To make it meaningful, the questions should be such that depth of the students in the subject is tested Oral examinations are to be conducted in co-cordial environment amongst the teachers taking the examination. Teachers taking such examinations should not have ill thoughts about each other and courtesies should be offered to each other in case of difference of opinion, which should be critically suppressed in front of the students.

5.Evaluationandmarkingsystem:

Basic honesty in the evaluation and marking system is absolutely essential and in the process impartial nature of the evaluator is required in the examination system to become popular amongst the students. It is a wrong approach or concept to award the students by way of easy marking to get cheap popularity among the students to which they do not deserve. It is a primary responsibility of the teacher that right students who are really putting up lot of hard work with right kind of intelligence are correctly awarded. The marking patterns should be justifiable to the students without any ambiguity and teacher should see that students are faced with unjust circumstances.