Sharp ANALOG Copier Simulation and Test Codes For analog copiers 1980-1995

Click here for 2120 copier

Press & hold "0" key for total count. Press "Clear", "Interrupt", "0", "Interrupt". OR "Clear, "0", "0", "Clear". OR "Clear", "Repeat", "0", "Pause". Then enter Simulation # and press "Print" key to enter selected simulation. 1: Drives scan/checks scan switches 2: Manually move scanner and check switches 3: Check paper path switches and in some machines cassette switches 4: Cassette switches 5: Lights up all display on panel 6. Heat lamp on/off 5 times 7: Light exposure lamp 8: Turns on bias voltage continuously 9: Turns on charge corona 10: Turns on transfer corona 11: Turns on discharge corona continuously 12: Turns on blank discharge lamp 13: Resets U1 14: Resets H3, H4, ect. 16: Check maintenance preset # 18: Check total count 19: Check copies since last PM 20: Reset PM counter to 0 21: Aging and check warm-up 22: Aging without paper 23: Aging no worm up or misfeed 24: Instant ready 25: Developer stir/calibration 26: Check lens motion (1 cycle) 27: Check lens motion 30: Test ADF switches 31: Test ADF 33: Check ADF/RADF components. 0: Forward feed motor. 1: Reverse feed motor. 2: Forward transport motor. 3: Reverse transport motor. 4: Exit motor speed normal. 5: Exit motor speed slow. 6: Paper feed solenoid. 7: Reverse solenoid. 8: Stopper solenoid. 34: Test drum separator. 39: Adjust document sensing. 40: Reads developer preset

41: Reads copy # since developer change 42: Resets copies on developer 45: Drum setting. First value read is current to machine setting. Enter new # to match the highest # on front flange of drum. 46: Adjust exposure. Use # key to change settings. 47: AE setting. Scan half way. Read display. Press {Print} to change exposure lamp voltage settings in 5 volt increments. 48: Horizontal magnification. 49: Vertical magnification. 50: Lead edge registrations. Use# key to change setting. 54: Transport roller rimming. Use {Print} switch to change setting 57: Edge erase setting. Change with # keys. 58: Lead edge and void adjustments Use zoom keys. 60: Original detection adjustment. See service manual 63: Test duplicate sensors. Actuate sensor and watch display. 64: Sorter components. 0: Solenoid 1: Motor 2: Gate 68: Test duplex components. 0: Transport 1: Paper feed 2: Duplex / Overlay gate 3: Paper Stop Feed 4: Registration clutch 5: Alignment plate 6: Trail edge stopper 7: Duplex reverse solenoid 70: ADF total count. 71: Duplex total count. 75: Reset ADF count to 0. 76: Reset Duplex count to 0. 77: Lens rank. 78. Setting up auto clear and double count for 11x17. CPOP 78 "Print". When "ready" lights, enter #, press "Print" to lock in ("Rea will go off). 0: No auto clear; Double count on PM and total. 1: No auto clear; Double count on PM, single on total. 2: No auto clear; Single count on PM, double on total. 3: No auto clear; Single count on PM and total. 40: Auto clear; Double count on PM and total. 41: Auto clear; Double count on PM, single on total. 42: Auto clear; single count on PM, double count on total. 43: Auto clear; Single count on PM and total. 79: Country setting. 8500 8800 Japan 14 4 Metric 15 5 Sharp Only 12 2 Inch (U.S.) 17 7 80: Setting options. 1: ADF only. 2: RADF only. 10: Duplex only. 11: ADF and Duplex. 12: RADF and Duplex. 20: 15 bin sorter only. 21: 15 bin sorter and ADF. 22: 15 bin sorter and RADF. 30: 15 bin sorter and duplex. 31: 15 bin sorter, ADF, duplex. 32: 15 bin sorter, RADF, duplex.

40: 20 bin sorter only. 41: 20 bin sorter and ADF. 42: 20 bin sorter and RADF. 50: 20 bin sorter and duplex. 51: 20 bin sorter, ADF, duplex. 52: 20 bin sorter, RADF, duplex, 94: Check and adjust original sensor. 95: 8500 Language display. English: RPM #1, set to "0". 97: send toner to transport. Sharp DIGITAL Copier Error Reset Codes

INPUT METHOD CLEAR - EXPOSURE SELECT- CLEAR - EXPOSURE SELECT For information only Use these error correction codes AT YOUR OWN RISK! NOT for use with Sharp Analog Copiers - NOT for use with post 1995 Sharp Copiers NOT all codes apply to all copiers! - Timing will vary from copier to copier
AR-150, 151, & 155 - Trouble Reset Press: "Clear", "Exposure Select Key", "Clear", "Exposure Select Key", "14", "Start Key" AR-150, 151, & 155 - Drum Counter Reset Press: "Clear", "Exposure Select Key", "Clear", "Exposure Select Key", "24", "Start Key", "7", "Start Key" AR-156 Developer counter re-setting. 24-06 Press "Clear" - "Exposure Select/Auto" - "Clear" - "Exposure Select/Auto". Machine will blank off. Use quantity buttons to make display read "24". Press "Print" button. Machine will flash 00. Press "Clear" 4 times and power machine off and back on. Maintenance counter re-setting 20-01 Press "Clear" - "Exposure Select/Auto" - "Clear" - "Exposure Select/Auto". Machine will blank off. Use quantity buttons to make display read "20". Press "Print" button. Machine will flash 00. Use quantity buttons to make display read "01". Press "Print" button. Machine will flash 000 Press "Clear" 4 times and power machine off and back on. AR-160, 200, 205; DM-2000, 2005, 2010, & 2015 - Trouble Reset Press: "Clear", "Interrupt", "0", "Interrupt", "14", "Start Key" AR-160, 200, 205; DM-2000, 2005, 2010, & 2015 - Drum Counter Reset Press: "Clear", "Interrupt", "0", "Interrupt", "24", "Start Key", "7", "Start Key"

Sharp AR-151 Digital Copier Error Codes Mail Code E7 E7 E7 E7 E7 E7 E7 L1 Sub Code 01 03 04 05 12 14 15 00 Trouble Code Duplex Memory Error HSYNC Not detected CCD White level Trouble CCD Black Level Trouble Shading Trouble ASIC Connection Trouble Copy Lamp Disconnection Feeding not Completed Detail Cancel with 26-39 Laser Diode APC trouble Copy Lamp Lighting ... CCD Drive Circuit Dirt on White Plate for Scanning White Level No Connection CPU and ASIC Copy Lamp Drive Circuit Mirror Home

L3 L4 L6 H2 H3 H4 U2 F6 F6 F6 F6 F6 F6

01 01 10 00 00 00 01 80 81 82 84 88 10

Timed out Return not completed Main Motor Lock Polygon Motor Lock Thermistor High Temp Low Temp Sum Check Error Com trouble fax - PWB Com trouble fax - PWB Com trouble fax - PWB Com trouble fax - PWB Com trouble fax - PWB Fax PWB Trouble

Mirror sensors

EEPROM Abnormal Protocol Parity Overrun Framing Timed Out

Copier model 2120 error codes

Error Codes Cause #1 "P" Paper feed problem or no paper "CC" Original detection fault "CH" Sorter fault "CH (blinking)" Developer unit not in place "PC" Card counter not installed "L1" Scan forward problem "L3" Scan return problem "L4" Drive fault "L5" Lens fault "L8-01" Main board fault "L8-03" Auto exposure sensor fault "H2-00" Fuser thermistor fault "H3-00" Fuser temp. too high "H4-00" Fuser temp. too low "U2-01" Memory loss "U2-04" EEPROM fault "U4-00" Communication problem between copier and duplex assy. "U4-02" Duplex alignment motor trouble "U4-03" Duplex rear edge plade motor trouble "U4-12" Duplex drive trouble "U5-00" Communication problem between copier and ADF "U5-01" ADF registration sensor "U5-02" ADF exit sensor fault "U5-11" ADF paper feed drive fault "U5-16" ADF fan motor drive fault "F1-00" Communication problem between copier & sorter "F1-02" Sorter transport motor drive fault "F1-04" Sorter bin sensor fault "F1-05" Sorter bin home sensor fault "F1-06" Sorter bin motor drive fault "F1-14" Sorter take out sensor fault "F1-16" Sorter grasping motor drive fault "F2-31" Image density sensor fault "F2-32" Drum mark sensor fault

"F2-33" "F2-35" "F2-37" "EE-EU" "EE-EL"

Grid voltage correction problem Grid voltage correction problem Drum mark sensor fault Undertoned Overtoned

U2 Code on SF-2014 - SF-2114 - SF-2214 reset code 16

LEXMARK OPTRA ERROR CODES

22 Paper Out or Paper Jam Check for paper in the paper tray Check the size of the paper in the paper tray to see if it is the same as what the printer is set for. The printer is set for (hardware or software) Defective D-roller Debris in the paper path Gears not turning or broken gear Defective paper tray Broken input sensor flag Defective input sensor board Defective system cable 2 Defective system board 23 Paper Jam Same as 22 with these additions: Exit Sensor flag (Fuser) Exit Sensor board (Fuser) System cable 1 24 Invalid Manual Feed Paper feed into the Manual feed when printer is pulling paper off paper tray Don't feed paper in the manual feed unless requested See 23 30 Open Cover Install Toner Cartridge Check the Switch activator (hangs down on left side of Top Cover) Check output voltages on the low voltage power supply. See Page 2-19 in the service manual Replace the high voltage power supply Replace system cable 2 (NOTE: the HVPS and system cable 2 can be checked by checking continuity across J14-5 and J14-6 and activating the switch on the HVPS) Replace the system board 31 Change Paper Paper size requested by the software is different than the installed paper Install the correct size paper and change size setting to match Software setup System board

31 Change Envelope Envelope size requested by the software is different than installed paper Install the correct size envelope and change size setting to match Software setup System board

35 Paper Error See 23 36 Load Paper See 23 37 Stop Command Received Press Start/Stop to clear Software setup Software drivers System board

40 System Board Failure Replace system board 41 Requested Font Not Available Install requested font and try again (font card or software) Software setup problem Defective font card Defective system board

42 Requested Font not Available See 41 43 Font Card Error Font card removed with power turned on. Cycle power Defective font card Defective system board 44 Font Card Error See 43 45 Downloaded Font Error Software setup Software drivers System board 46 Download Character Error See 45 47 Language Error

Normal Mode (IBM) Unsupported card installed Defective card Defective system board Postscript Mode Make sure that Postscript is selected on printer and computer Make sure that a Postscript font card is being used Defective font card Defective system board

54 Serial Error Check serial configuration settings (printer and computer) Communication cable I/O card in Computer System board

55 Font Error See 45 89 Output Tray Full (4029-04x only) Remove paper from output tray Check flag operation Replace the card photo sensor Replace the cable Replace the system board

900 System Board Failure Remove options and try again (NOTE: when removing the Postscript board, you must replace the 2 IBM ROMs) If the printer now works, replace options one at a time to test them Replace system board Defective system board 910 Font Card Failure Reseat font card Defective font card Defective system board 920 Fuser not up to temperature Check resistance of the fuser, lamp, thermofuse, thermistor Low voltage power supply There is no reliable check, other than to exchange the part out System cable 1 Check for continuity Fuser power cable Check for continuity

 System board 921 Fuser not up to Temperature See 920 922 Fuser not up to Temperature See 920 923 Fuser Over Temperature See 920 930 Mirror Motor (not up to speed) Reseat cables between the print head and the system board Defective print head Defective cables Defective system board

931 Mirror Motor speed detect error See 930 932 Mirror Motor speed detect error See 930 940 Laser Beam detect failure See 930 941 Laser beam detect failure See 930 950 System Board Failure See 900 960 Memory Error See 900 970 Fan not turning Reseat cables between the fan and the system board Replace the fan Replace the cables Replace the system board

980 System Board Failure See 900 990 System Board Failure See 900

TO GET SHARP METER READINGS

SF750, 755, 756, 770, 771, 781, 7100, 7200, SF7300, 7350, 7370, 7700, 7750, 7750, 7800, SF7850, 7855, 7900, 8100, 8300, 8350, 8400, SF8500, 8570, 8600, 8800, 8870, 8875, 9400, SF9500, 9550, 9700, 9750, 9800, 1420, 1430, SF2014, 2022, 2025, 2027, 2114, 2116, 2214, SF2314, 2414, 2514,AR160, 161, 200, 205, 162, 163, 164, 201, HOLD DOWN 0 KEY. 207,ARM160, ARM205

AR150N/151/F152/153/155N /156/157 CLEAR KEY - (Hold down several seconds.)

HITACHI AR-C150/250/C160/270

UTILITY-METER COUNT

Make sure the copy button is lit up--hold down. You will get 2 readings, 1 for color, 1 for black & white. Now make sure the print button is lit up, hold down. You will get 2 readings, 1 for color, 1 for black & white. Add all 4 together to get total.

ARC260M

Go to the custom settings key and go to total count - Print this screen to get accurate readings

SF2010

MANUAL COUNTER UNDER LID Press Menu key until custom setting is displayed press OK key, Press up arrow key until Total Count is displayed. Press OK Press up arrow key until Display total count shows. Press OK and display will show Total Count.

AR-P350/450

AR280, 285, 287, 335, 405, 505, 507, 235, 275, 336, 337, 407,M208, M350, M450, M280 ARM550, M620, M700, M237, M277 AR650/651/800/810 SF2030, 2035, 2040, 2050, 2052, SD3062, 2060, SD4085, AR5132

HOLD DOWN COPY BUTTON.

Manual counter on machine beside Op Panel HOLD DOWN SCROLL KEY, OR Press the clear key, interrupt key, and clear key again. Enter key operator code (their code is 5 digits--most are 00000) Enter 29 (the total count will be displayed), When finished, press the Clear All key.

AR168S, AR168D

Make sure machine is in the copy mode. Press Menu Key - Press < key until total count appears in the display -Press Enter key and count will be displayed