Et Data Sheet
Uploaded by
Abd Elrahman HamdyEt Data Sheet
Uploaded by
Abd Elrahman HamdyProduct Bulletin
51.1:ET
D100022X012
April 2011
ET Valve
Fisherr ET, EAT, and ETR
Sliding-Stem Control Valves
Fisher ET, EAT, and ETR general-purpose control
valves (figures 1, 2, 3, and 4) are used for throttling
or on-off control of a wide variety of liquids and
gases. All three valve designs have single ports,
balanced valve plugs, and cage guiding.
Metal-to-PTFE seating for stringent shutoff
requirements is standard in all valves except those
with Cavitrolt III cages. Metal-to-metal seating for
higher temperatures is standard for valves with
Cavitrol III cages and optional for all other valves.
The temperature limits of ET valves can be extended
above 232_C (450_F) by using PEEK
(PolyEtherEtherKetone) anti-extrusion rings in
combination with a spring-loaded PTFE seal. The
PEEK anti-extrusion rings expand to close off the
clearance gap between the plug and the cage where
the PTFE seal may extrude at high temperatures
and pressures. The temperature limits are extended
to 316_C (600_F) for non-oxidizing service and to
260_C (500_F) for oxidizing service.
The ET product line is available for a wide range of
applications, including sulfide and chloride
stress-cracking environments common to the oil and
gas production industries. To discuss available
constructions, contact your Emerson Process
Management sales office and include the applicable
codes and standards required for these
environments.
The easy-et Valve Family
ET, EAT, and ETR control valves are part of the
versatile easy-e family of Fisher industrial control
valves. easy-e valves share the following
characteristics:
D Multiple trim material choices
D Interchangeable, restricted-capacity trims and
full-sized trims to match variable process flow
demands
D Different cage/plug styles that provide particular
flow characteristics for highly-specialized
applications. The standard cage comes in three
www.Fisher.com
W1916-3 / IL
Figure 1. Fisher ET Control Valve with 667 Actuator
different flow characteristics: J quick-opening,
J linear, or J equal percentage.
D Whisper Trimt I, Whisper Trim III (figure 7),
and WhisperFlot cages (figures 5 and 6) attenuate
aerodynamic noise in gaseous service.
D To help eliminate cavitation damage in a
properly-sized valve, a standard-travel, Cavitrol III,
one-stage cage (figure 9) and a long-travel, Cavitrol
III, two-stage cage are available in the NPS 1
through NPS 8 ET control valve.
Product Bulletin
51.1:ET
April 2011
ET Valve
Contents
Features
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ENVIRO-SEALt and HIGH-SEAL
Packing Systems . . . . . . . . . . . . . . . . . . . . . . . . 4
ANSI/FCI Class VI Shutoff
Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Tables
Available Constructions . . . . . . . . . . . . . . .
Shutoff Classifications . . . . . . . . . . . . . . . .
Class VI Shutoff Availability . . . . . . . . . . . .
Class VI Trim Materials . . . . . . . . . . . . . . .
Trim Materials . . . . . . . . . . . . . . . . . . . . . . .
Materials and Temperature Limits for
Other Parts . . . . . . . . . . . . . . . . . . . . . .
Valve Body/Trim Temperature
Capabilities . . . . . . . . . . . . . . . . . . . . . .
Bonnet Selection Guidelines . . . . . . . . . .
Maximum Flow Coefficients . . . . . . . . . . .
Port Diameters, Valve Plug Travel,
Stem and Yoke Boss Diameters . . . . .
Metal Trim Parts . . . . . . . . . . . . . . . . . . . .
Bolting Materials and Temperature Limits
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ordering Information . . . . . . . . . . . . . . . . . . . . . .
Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
3
4
4
8
15
16
17
17
18
21
21
22
25
26
42
ENVIRO-SEAL Packing System
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 44
D Compliance with the Clean Air Act
ENVIRO-SEAL packing systems (figures 10 and 11)
that provide an improved stem seal to help prevent
the loss of process fluid are available. These
packing systems feature PTFE or Graphite ULF
packing with live-loading for reduced packing
maintenance.
D PTFE Seating for Long-Lasting Shutoff
CapabilityControlled compression of standard
seat construction protects PTFE disk between metal
disk seat and disk retainer (figure 2). Only the edge
of the PTFE disk is contacted by the flowstream
during normal operation. Excellent shutoff is
maintained by a backup ring or spring-loading that
forces the valve plug seal ring against the cage
(figure 2).
D Valve Plug Stability Rugged cage guiding
provides high valve plug stability, which reduces
vibration and mechanical noise.
D Cost-Effective Operation and Maintenance
EconomyIncreased wear resistance of hardened
stainless steel trim means longer-lasting service.
When inspection or maintenance is necessary, the
body can stay in the pipeline during removal of trim
parts. Balanced valve plug construction permits use
of smaller, lower-cost Fisher actuators. The ETR
valve also permits easy body interior access without
having to remove the bonnet or actuator (figure 4).
And, trim inventory costs are cut because
dimensional standardization permits use of most
standard easy-e trim parts.
D Compliance with European Standards
Valves are available with dimensions specified by
EN/DIN standards. See figure 16.
D Sour Service Capability Unless otherwise
noted, references are to NACE MR0175-2002.
Optional materials are available to meet NACE
MR0103 and NACE MR0175 / ISO 15156. Material
requirements under these standards vary by edition
and year of issue; the specific standard must be
specified.
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 1. Available Constructions
VALVE BODY MATERIAL AND END CONNECTION STYLE(1)
VALVE
ET
VALVE SIZE,
NPS
1, 1-1/2, or 2
2-1/2, 3, 4, 6, or 8
Cast Iron Valve Body
CL125
FF Flanged
CL250
RF Flanged
Screwed
X
X
X
X
-----
EAT
1 or 2
3, 4, or 6
-----
ETR
1, 1-1/2, or 2
2-1/2, 3, or 4
-----
VALVE
ET
EAT
ETR
VALVE SIZE,
DN
25, 40, 50, 65,
80, 100, 150, or
200
25, 50, 80, 100,
or 150
25, 40, 50, 65,
80, or 100
Carbon Steel, Alloy Steel, or Stainless Steel Valve Body
RF or RTJ Flanged
CL150
CL300
CL600
Butt
Weld
Socket
Weld
X
---
X
X
X
X
X
X
X
X
X
X
-----
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
--------------STEEL VALVE BODY MATERIAL AND RAISEDFACE END CONNECTION STYLE(2)
X
---
PN16
PN25
PN40
PN63
PN100
X = Available Construction.
1. End connection style abbreviations: FF - Flat Faced, RF - Raised Face, RTJ - Ring Type Joint.
2. End connection EN10921/B.
Table 2. Shutoff Classifications Per ANSI/FCI 70-2 and IEC 60534-4
Valve Design
All except those with Cavitrol III cages
Seating
PTFE
Shutoff Class
Standard Air Test (maximum leakage is 0.05 mL/min/psid/inch port diameter)(2)
V (optional)
VI (optional)(4)
Metal
IV (standard)
V (optional)(1)
VI (optional)(4)
ET with Cavitrol III one-stage cage
Metal
ET with Cavitrol III two-stage cages
Metal
IV (standard)
V (optional)
ET and EAT w/ TSO (Tight Shutoff)
trim (CL125 through 600)
ET w/ TSO (Tight Shutoff) trim (CL125
through 600)
Replaceable,
protected soft
seat
Std or Cavitrol III
trim.
Replaceable,
protected soft
seat.
V
TSO(3)
TSO is not an ANSI/FCI leakage class.
Valves with TSO trim are factory tested to a more stringent Emerson Process
Managementt test requirement of no leakage at time of shipment. Test medium
is water. Specify service nP when ordering. Shutoff class V.
1. Class V shutoff requires spring-loaded seal ring, radius-seat plug, and wide-bevel seat ring (not available with 8-inch port, quick-opening cage). Not available with trims 4, 29, and 85.
2. This is a special non-ANSI/FCI leakage class.
3. For additional information, contact your Emerson Process Management sales office.
4. Refer to table 3.
Product Bulletin
51.1:ET
April 2011
ET Valve
ENVIRO-SEAL, HIGH-SEAL Packing
Systems
ENVIRO-SEAL and HIGH-SEAL packing systems
offer exceptional sealing capabilities. These systems
easily install in existing valves or can be purchased
with new valves. These systems help seal the
process to conserve valuable process fluid. The
long-life and reliability of these systems also reduce
maintenance costs and downtime.
For applications requiring compliance with
environmental protection regulations, the unique
ENVIRO-SEAL packing system (figure 11) and a
unique ENVIRO-SEAL bellows seal system
(figure 10) are offered. The emission control packing
system keeps emission concentrations below the
EPA 100 ppm requirement.
Graphite ULF packing system
(figure 11) is offered. The HIGH-SEAL packing
system provides improved sealing at
pressure/temperature ratings beyond ENVIRO-SEAL
limits.
ENVIRO-SEAL packing systems, available with
PTFE, Graphite ULF, or duplex packing, and the
HIGH-SEAL Graphite ULF packing system feature
live-loading and unique packing-ring arrangements
for long-term, consistent sealing performance.
ANSI/FCI Class VI Shutoff Capabilities
ET valves with soft seat and metal seat
constructions can provide ANSI/FCI Class VI shut-off
capabilities. See tables 3 and 4.
For an excellent stem seal in applications that are
not environmentally-sensitive, the HIGH-SEAL
Table 3. Class VI Shutoff Availability(1, 2)
Valve
Port Size, Inches
Seat
ET
3.4375 7
Soft
Minimum Seat Load
See Catalog 14
ET
3.4375 7
Metal
300 lbs/lineal inch
1. Limited retrofit capability. Consult your Emerson Process Management sales office.
2. Not for use with NPS 8.
Table 4. Class VI Trim Materials
VALVE
ET
CAGE/SEAT
RING RETAINER
VALVE PLUG
SEAT RING
SEAL RING
S31600 / ENC
S31600 w/ standard
beveled seat
S31600/PTFE
S31600 / ENC
S31600/CoCr-A seat
w/ radiused seat
(special design)
S17400 (17-4PH
SST)
S17400
_C
_F
UHMWPE(1) R30003
198 to 66
325 to 150
S31600 w/ wide
beveled seat
(special design)
UHMWPE R30003
198 to 66
325 to 150
S41600 w/ standard
beveled seat
S31600/PTFE
UHMWPE R30003
29 to 66
20 to 150
S41600 w/ radiused
seat (special design)
S31600 w/ wide
beveled seat
(special design)
UHMWPE R30003
29 to 66
20 to 150
1. UHMWPE (Ultra High Molecular Weight Polyethylene)
TRIM TEMPERATURE LIMIT
Product Bulletin
51.1:ET
April 2011
ET Valve
RETAINING
RING
SEAL RING
LOAD
RING
METAL
BACKUP
RING
SEAL RING
W7019-1 / IL
W09952 / IL
W29141 / IL
STANDARD NPS 8
CONSTRUCTION
NPS 1 THROUGH 4 ET
(ALSO NPS 1 THROUGH 6 EAT)
NPS 6 OR 8 ET
SPRING-LOADED SEAL RING CONSTRUCTION
FOR USE WITH CAVITROL CAGES AND FOR
METAL SEAT WITH OPTIONAL
CLASS V SHUTOFF
CAGE
GASKET
PTFE V-RING
PACKING
BONNET
GASKET
BONNET GASKET
BACKUP RING
SEAL RING
SHIM
SPIRAL
WOUND
GASKET
RESTRICTED
TRIM
ADAPTORS
VALVE PLUG
SHIM
SPIRAL
WOUND
GASKET
W2001-2 / IL
OPTIONAL RESTRICTED TRIM
PIN
SEAT RING
GASKET
METAL
DISK SEAT
PTFE DISK
METAL DISK
RETAINER
METAL
SEAT
RING
W0983-2 / IL
W31623 / IL
STANDARD NPS 1 THROUGH
6 CONSTRUCTION
OPTIONAL METAL-TO-METAL
SEATING
Figure 2. Fisher ET Sectional with Standard Cages
Product Bulletin
51.1:ET
April 2011
ET Valve
W1557-4 / IL
W0972-3 / IL
Figure 3. Fisher EAT Sectional
Figure 4. Fisher ETR Sectional
W6980 / IL
WhisperFlo TRIM
W6851-1 / IL
Figure 5. Typical Valve with WhisperFlo Aerodynamic Trim
Product Bulletin
51.1:ET
April 2011
ET Valve
W7065 / IL
W6851-1
Figure 6. Typical WhisperFlo Cage
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 5. Typical Combinations of Metal Trim Parts for All Valves Except Those for NACE MR0175 / ISO 15156 and MR0103
Specifications(1), Cavitrol III(2), 6-Inch Whisper Trim III(3), and 4-, 6-, and 8-Inch WhisperFlo Cages(6)
Trim Designation
1 (typically used with optional
metal-seat constructions in all
designs and body materials
except CF8M)
Valve Plug
Cage
Seat Ring or
Liner for Optional
Metal-Seat Construction
Optional Liner
(Metal Seat
EAT Valve
Only)
S41600 HT or CA15 HT(4)
S41600 HT
S41600 HT
CB7Cu-1 HT
S17400 HT(5)
CB7Cu-1 HT(5)
S31600
with seat and guide
hard faced with
CoCr-A
hardfacing alloy
R30006 (alloy 6)
4(7)
S31600
CB7Cu-1 HT
S31600
S31600
27
S31600
with seat and guide
hard faced with
CoCr-A
hardfacing alloy
CF8M with
electroless
nickel coating
(ENC)
S31600
disk retainer with
CoCr-A disk seat
R30006 (alloy 6)
28(8)
S31600
with seat hard
faced with CoCr-A
hardfacing alloy
CF8M with
electroless
nickel coating
(ENC)
S31600
disk retainer with
CoCr-A disk seat
R30006 (alloy 6)
29 (standard for CF8M bodies
in all designs regardless of
seat construction)(8)
S31600
CF8M with
electroless
nickel coating
(ENC)
S31600
S31600
37 and 37H (trim 37H has
clearances for
high-temperature service
above 210_C [410_F])
S31600
with seat and guide
hard faced with
CoCr-A
CB7Cu-1 HT
S31600
disk retainer with
CoCr-A disk seat
Seat Ring:
R30006 (alloy 6)
57 (standard for standard
PTFE-seat ET, EAT, ETR in all
body materials except CF8M)
S41600 HT
S17400 HT
S31600
1. For NACE MR0175 / ISO 15156 and MR0103 specification trims, see table 17
2. For Cavitrol III trims, see table 6.
3. For 6-inch Whisper Trim III trims with 5.375 inch port diameter, see table 8
4. CA15 is used for NPS 6 and 8 full-sized and restricted-trim valves.
5. For 8-inch Whisper Trim I and 8-inch Whisper Trim III.
6. For 4-, 6-, and 8-Inch WhisperFlo trims, see table 7.
7. Not for use with Whisper Trim I.
8. Not for use with Whisper Trim I with 136 mm (5.375 inch) and larger ports.
Disk Seat and Retainer
for
Standard
PTFE-Seat
Construction
R30006 (alloy 6)
S31600
S31600
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 6. Cavitrol III(1) Metal Trim Part Materials and Body/Trim Temperature Capabilities
MATERIAL TEMPERATURE
CAPABILITY
BODY & BONNET
TRIM
DESIGNATION
76
VALVE
PLUG
Heat-treated
S42000
CAGE
CAGE
RETAINER
S17400
S31600
SST H900
for Cavitrol
III 1-stage
or
S17400
SST H1075
for Cavitrol
III 2-stage
SEAT
RING
S17400
with H900
heat-treat
condition
_C
_F
Minimum
Maximum
Minimum
Maximum
WCC carbon steel,
WC9 chrome moly
steel, or LCC
carbon steel
29
These
materials not
limiting factors
20
These
materials not
limiting factors
CF8M
NPS 1,
1-1/2, or 2
valve
body size
29
These
materials and
sizes not
limiting factors
20
These
materials and
sizes not
limiting factors
NPS 2-1/2
or 3
valve
body size
29
216
20
420
NPS 4, 6,
or 8 valve
body size
29
177
20
350
1. Available only in NPS 1 through 8 ET valves.
Table 7. WhisperFlo Metal Trim Part Materials and Valve Body/Trim Temperature Capabilities (NPS 4, 6, and 8 Fisher ET only)
TRIM
DESIGNATION
901
MATERIAL TEMPERATURE CAPABILITY(1)
VALVE
BODY
WCC
VALVE
PLUG
S41600
CAGE
CAGE
RETAINER
_C
SEAT
_F
Min
Max
Min
Max
S41000
WCC ENC
S41600
29
316
20
600
S41000
WCC ENC
S31600/CoCrA
29
316
20
600
S41000 NACE
WCC/NACE/ENC
S31600/CoCrA
29
316
20
600
S31603/
R31233
S31600/ENC
S31600/CoCrA
198
316
325
600
902
WCC
926
WCC
936
316
CF8M
901C
WCC
S31600/CoCrA
Seat and
Guide
S31600/CoCrA
Seat and
Guide
S31600/CoCrA
Seat and
Guide
S41000
S41000
WCC ENC
S31600/PTFE
29
232
20
450
904C
WCC
S31600
S41000
WCC ENC
S31600/PTFE
29
149
20
300
984C
WCC
S31600
S41000 NACE
WCC/NACE/ENC
S31600/PTFE
29
149
20
300
CF8M
S31600
S31603/
R31233
S31600/ENC
S31600/PTFE
73
149
100
300
CD3MN
S31803/CoCrA
Seat and
Guide
51
316
60
600
S31803/
R31233
S31800/Cr Plate
S31803/CoCrA
Seat
46
316
51
600
29
316
20
600
51
232
60
450
46
232
51
450
29
232
20
450
985C
990
LCC
WCC
CD3MN
990C
LCC
WCC
S31803/CoCrA
Seat and
Guide
S31803/
R31233
S31800/Cr Plate
S31803/PTFE
1. Temperatures above 232_C (450_F) require PEEK anti-extrusion rings and spring-loaded seal ring. This option allows ET construction to be used up to 316_C (600_F) for
non-oxidizing service and 260_C (500_F) for oxidizing service.
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 8. Whisper Trim III Metal Trim Part Materials and Body/Trim Temperature Capabilities (NPS 6 Fisher ET with 5.375 inch port
only)
Trim
Designation
Valve Plug
301 (standard S17400 HT
for all body
materials
except CF8M)
301C (for soft S17400 HT
seats)
304
Cage
Cage
Retainer
Baffle
(For Level
D3 Cage
Only)
S41600 HT Carbon steel
NACE with
electroless
nickel coating
(ENC)
Steel
S41600 HT Carbon steel
NACE with
electroless
nickel coating
(ENC)
Steel
S31600 with S41600 HT
seat and
guide
hard-faced
with CoCr-A
Carbon steel
NACE with
electroless
nickel coating
(ENC)
Steel
S31600 with
seat and
guide
hard-faced
with CoCr-A
S31600 with
electroless
nickel
coating
(ENC)
S31600 with
electroless
nickel coating
(ENC)
S31600
S31600 with
seat and
guide
hard-faced
with CoCr-A
S31600 with
electroless
nickel
coating
(ENC)
S31600 with
electroless
nickel coating
(ENC)
S31600 with
seat and
guide
hard-faced
with CoCr-A
S31600 with
electroless
nickel
coating
(ENC)
Carbon steel
NACE with
electroless
nickel coating
(ENC)
Steel
313C (NACE S31600 with
compatible)
seat and
(for soft seats) guide
hard-faced
with CoCr-A
S31600 with
electroless
nickel
coating
(ENC)
Carbon steel
NACE with
electroless
nickel coating
(ENC)
Steel
312
(for level D
NACE)
312C
(for level D
NACE)
313 (NACE
compatible)
Disk Seat
Seat Ring for
Body
and Retainer
Bonnet,
Metal-Seat
for
& Bonnet
Construction
Spacer
PTFE-Seat
Construction
S41000 HT
--WCC carbon
steel or WC9
chrome moly
steel
S31600
---
---
_C
_F
29 to
316(1)
20 to
600(1)
CF8M
(316 SST)
29 to 163
20 to 325
WCC carbon
steel or WC9
chrome moly
steel
29 to 204
20 to 400
CF8M
(316 SST)
29 to 163
20 to 325
29 to
316(1)
20 to
600(1)
29 to 177
20 to 350
29 to
260(1)
20 to
500(1)
CF8M
(316 SST)
198 to
316(1)
325 to
600(1)
WCC carbon
steel or WC9
chrome moly
steel
29 to
260(1)
20 to
500(1)
CF8M
(316 SST)
198 to
316(1)
325 to
600(1)
29 to 204
20 to 400
29 to
316(1)
20 to
600(1)
WCC carbon
steel or WC9
chrome moly
steel
29 to 204
20 to 400
CF8M
(316 SST)
29 to 204
20 to 400
S31600 with
WCC carbon
seat hard-faced steel or WC9
chrome moly
with CoCr-A
steel
CF8M
(316 SST)
S31600
---
S31600
---
S31600 with
WCC carbon
seat hard-faced steel or WC9
chrome moly
with CoCr-A
steel
---
S31600 with
WCC carbon
seat hard-faced steel or WC9
with CoCr-A
chrome moly
steel
CF8M
(316 SST)
S31600
---
Material Temperature
Capability
1. Temperatures above 232_C (450_F) require PEEK anti-extrusion rings and spring-loaded seal ring. This option allows ET construction to be used up to 316_C (600_F) for
non-oxidizing service and 260_C (500_F) for oxidizing service.
10
Product Bulletin
51.1:ET
April 2011
ET Valve
BONNET
SPACER
CAGE
RETAINER
W2670 / IL
W3746A-4 / IL
Figure 7. Metal Seat and Whisper Trim III Cage in NPS 6
Fisher ET Valve
Figure 9. Cavitrol III One-Stage Cage
BELLOWS
SEAL
BONNET
VALVE PLUG
SEAL
W7020-1 / IL
Figure 8. Typical Balanced TSO Trim
PROTECTED
SOFT SEAT
BELLOWS SEAL
ASSEMBLY
WITH VALVE
PLUG
W5821-1 / IL
Figure 10. Typical ENVIRO-SEAL Bellows Seal Bonnet and
Bellows Seal Assembly
11
Product Bulletin
51.1:ET
April 2011
ET Valve
PACKING
BOX
STUDS
SPRINGS
PACKING
BOX
STUD
SPRINGS
ANTI
EXTRUSION
RING
PACKING
RING
FOLLOWER
VALVE
BONNET
LANTERN
RING
PACKING
W58033 / IL
W8532-1
TYPICAL ENVIRO-SEAL PACKING SYSTEM
WITH PTFE PACKING
TYPICAL ENVIRO-SEAL PACKING SYSTEM
WITH GRAPHITE ULF PACKING
PACKING
BOX
STUD
SPRING
FOLLOWER
PACKING
W7018 / IL
W8533-1
TYPICAL HIGH-SEAL PACKING SYSTEM
WITH GRAPHITE ULF PACKING
TYPICAL ENVIRO-SEAL PACKING SYSTEM
WITH DUPLEX PACKING
Figure 11. ENVIRO-SEAL and HIGH-SEAL Packing Systems
12
Product Bulletin
51.1:ET
April 2011
ET Valve
FLUID TEMPERATURE, qC
FLUID TEMPERATURE, qC
50
100
150
200 250
100 50
110
1600
100
150
200 250 300
110
70
60
800
50
600
40
29C OR 57C
30
400
20
200
90
1200
PRESSURE DROP, PSI
4C
OR
29C
1000
80
PRESSURE DROP, BAR
1200
200
100
0
100 200 300 400
20
FLUID TEMPERATURE, qF
80
70
1000
60
800
1 OR
37
50 100
150
50
40
30
400
20
10
500
200
100
200 250 300
100 50
100
1400
600
FLUID TEMPERATURE, qC
110
1600
0
100 200 300 400 500
450 4
20
FLUID TEMPERATURE, qF
FOR OPTIONAL METAL SEATING
WITH CL600 WCC STEEL, OR WC9 CHROME
MOLY STEEL, BODY
FLUID TEMPERATURE, qC
0
1
OR
37H
600
TRIM CAPABILITIES FOR PTFE SEATING
100 50
200
10
100
1400
90
PRESSURE DROP, PSI
50
100
1400
1600
50 100
150
200 250 300
110
1600
90
800
1
OR
37H
1 OR
37
70
60
50
600
40
400
30
20
1,4 OR 37
10
100
0
100 200 300 400 500
450 4
50
20
FLUID TEMPERATURE, qF
600
70
28,29
800
100
40
30
400
20
29
10
100
100
200
300
400 500
450 4
600
FLUID TEMPERATURE, qF
2
30
25
300
20
5
100
15
10
5
0
0
100 200 300 400 600
450
20
FLUID TEMPERATURE, qF
FOR OPTIONAL METAL SEATING WITH
2 CAST IRON BODY
CL250B
PRESSURE DROP, BAR
35
400
100
200
40
500
200
50
27
FOR OPTIONAL METAL SEATING WITH
CL600 CF8M(316 SST) BODY
200
600
1 OR
37
60
27
600
FOR OPTIONAL METAL SEATING WITH
CL600 LCC STEEL BODY
0
FLUID TEMPERATURE, qC
PRESSURE DROP, PSI
80
1000
200
200
90
1200
PRESSURE DROP, PSI
1000
PRESSURE DROP, BAR
PRESSURE DROP, PSI
80
37
200
A6736-2/IL
100
1400
1200
PRESSURE DROP, BAR
PRESSURE DROP, BAR
100 50
NOTES:
1 USE TRIM 27 INSTEAD OF TRIM 29 FOR NONLUBRICATING
FLUIDS SUCH AS SUPERHEATED STEAM OR DRY GASES
BETWEEN 149qC (300qF) AND 232qC (450qF).
2 DO NOT EXCEED THE MAXIMUM PRESSURE AND TEMPERATURE
FOR THE PRESSURE RATING OF THE BODY MATERIAL USED,
EVEN THOUGH THE TRIMS SHOWN MAY HAVE HIGHER CAPABILITIES.
3 TRIMS 4 AND 29 MAY BE USED UP TO 99 BAR (1440 PSI) WITH CLEAN
DRY GAS. FOR PROCESS FLUIDS OTHER THAN CLEAN DRY GAS,
USE TRIMS 4 AND 29 ONLY UP TO 21 BAR (300 PSI).
4 TRIMS, 1, 27, AND 37H TEMPERATURE LIMITS CAN BE EXTENDED
TO 316qC (600qF) FOR NON-OXIDIZING SERVICE OR 260qC
(500qF) OXIDIZING SERVICE IF PEEK ANTI-EXTRUSION RINGS
ARE USED WITH SPRING-LOADED SEAL RINGS.
5 USE TRIM 37H INSTEAD OF TRIM 37 FOR TEMPERATURES
ABOVE 210qC (410qF). REQUIRES ANTI-EXTRUSION RINGS AND
SPRING-LOADED SEAL RINGS FOR TEMPERATURES
ABOVE 232qC (450qF).
Figure 12. Typical Trim for All Valves Except Those with Cavitrol III, Whisper Trim III, or WhisperFlo Cages
13
Product Bulletin
51.1:ET
April 2011
ET Valve
LIQUID TEMPERATURE, qC
100 50
50
100
150
200 250 300
110
1600
100
1400
PRESSURE DROP, PSI
80
70
1000
60
800
50
76
600
40
76
30
400
20
200
PRESSURE DROP, BAR
90
1200
10
200
100
0
20
100
200
300
400 500
450 2
LIQUID TEMPERATURE, qF
600
WITH STEEL OR STAINLESS STEEL BODIES
NOTES:
1 DO NOT EXCEED THE MAXIMUM PRESSURE AND TEMPERATURE FOR THE PRESSURE RATING
OF THE BODY MATERIAL USED, EVEN THOUGH THE TRIM SHOWN MAY HAVE HIGHER CAPABILITIES.
2 TRIM 76 TEMPERATURE LIMITS CAN BE EXTENDED TO 316qC (600qF) FOR NON-OXIDIZING
SERVICE OR 260qC (500qF) FOR OXIDIZING SERVICE IF PEEK ANTI-EXTRUSION RINGS ARE USED WITH
SPRING-LOADED SEAL RINGS.
A6737/IL
Figure 13. Typical Trim for Cavitrol III Cage Constructions
FLUID TEMPERATURE, qC
FLUID TEMPERATURE, qC
0
50
100
150
200 250 300
300
110
1600
50
100
150
110
70
1000
60
800
301
301C
600
50
301
40
30
400
20
200
0
100
0
100 200 300 400 500
450 2
20
FLUID TEMPERATURE, qF
WITH CL600 WCC STEEL
OR WC9 CHROME MOLY BODY
600
90
1200
PRESSURE DROP, PSI
80
100
1400
PRESSURE DROP, BAR
1200
80
70
1000
60
312, 312C
800
50
312
600
40
30
400
20
10
200
10
0
200
500 400
325
100
100
200
300
FLUID TEMPERATURE, qF
WITH CL600
316 STAINLESS STEEL (CF8M) BODY
NOTES:
1 DO NOT EXCEED THE MAXIMUM PRESSURE AND TEMPERATURE FOR THE PRESSURE RATING OF THE
BODY MATERIAL USED, EVEN THOUGH THE TRIMS SHOWN MAY HAVE HIGHER CAPABILITIES.
2 TRIMS 301 AND 312 TEMPERATURE LIMITS CAN BE EXTENDED TO 316qC (600qF) FOR
NON-OXIDIZING SERVICE OR 260qC (500qF) FOR OXIDIZING SERVICE IF PEEK ANTI-EXTRUSION RINGS
ARE USED WITH SPRING-LOADED SEAL RINGS.
A6738/IL
Figure 14. Typical Trim for NPS 6 Fisher ET Valve with Whisper Trim III Cage
14
200 250 300
1600
90
PRESSURE DROP, PSI
100 50
100
1400
200
200
400 500
450 2
600
PRESSURE DROP, BAR
100 50
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 9. Materials and Temperature Limits for Other Parts
PART
MATERIAL
TEMPERATURE CAPABILITIES
_C
Minimum
Cast iron body
WCC body
LCC body
Body-to-bonnet
bolting. See table
18 for NACE
bolting materials
and temperature
CF8M
limits
(316 stainless steel)
body
Studs
Steel SA-193-B7
Nuts
Steel SA-194-2H
Studs
Steel SA-193-B7
Nuts
Steel SA-194-2H
Studs
Steel SA-193-B7 (std) (NACE [non-exposed
bolting])
48
- - -(5)
55
- - -(5)
Nuts
Steel SA-194-2H (std) (NACE [non-exposed
bolting])
46
- - -(5)
50
- - -(5)
Studs
304 stainless steel SA-320-B8
Nuts
304 stainless steel SA-194-8
- - -(5)
38
- - -(5)
100
Studs
316 stainless steel SA-193-B8M
(strain-hardened) or
316 stainless steel SA-193-B8M
Nuts
316 stainless steel SA-194-8M
29
20
450
20
- - -(5)
46
- - -(5)
50
- - -(5)
- - -(5)
PTFE
73
204
100
400
Fluoroelastomer(1)
18
204
400
Ethylene-propylene(2)
40
232
40
450
For use with air and
hydrocarbons
40
71
40
160
For use with other compatible
fluids
40
82
40
180
Nitrile(3)
For applications
using PEEK
Anti-Extrusion
Rings:
Spring-loaded
valve plug seal
232
Maximum
Steel SAE Grade 5
Backup ring
Spring-loaded
valve plug seal(7)
29
Minimum
Cap screws
Disk
2-piece valve plug
seal (standard for
NPS 1 thru 6
valves except
those with
Cavitrol III cage)
_F
Maximum
- - -(5)
- - -(5)
Seal ring
Carbon-filled PTFE
73
232
100
450
Backup
ring(4)
416 stainless steel
29
- - -(5)
20
- - -(5)
316 stainless steel
- - -(5)
- - -(5)
- - -(5)
- - -(5)
Retaining
ring(4)
302 stainless steel (N07750, NACE Std)
Seal ring
PTFE with N10276 spring
73
232
100
450
Backup
ring(4)
416 stainless steel
29
- - -(5)
20
- - -(5)
316 stainless steel
- - -(5)
Retaining
ring(4)
302 stainless steel
Seal ring
PTFE/graphite with N10276 spring
Anti-extrusion rings
PEEK (PolyEtherEtherKetone)
- - -(5)
316(6)
232
- - -(5)
- - -(5)
600(6)
450
- - -(5)
- - -(5)
Valve plug stem
S31600 (S20910, NACE Std.)
Load ring (NPS 8 ET valve only)
S17400 or
optional N06600 or N05500
- - -(5)
Cast iron
73
232
100
450
WCC steel
29
- - -(5)
20
- - -(5)
Restricted trim
adaptors
- - -(5)
316 stainless steel
- - -(5)
Seat ring, bonnet
and cage gaskets
FGM (standard)
- - -(5)
Spiral wound
gasket
N06600/graphite (FGM-standard)
PTFE-coated N04400
N04400/PTFE
316 stainless steel
Shim
Packing
- - -(5)
N04400
(temperatures
shown are material
temperature
capabilities)
See table 11 PTFE V-ring
for proper
PTFE/composition
bonnet
Graphite ribbon/filament
selection
- - -(5)
- - -(5)
- - -(5)
149
- - -(5)
- - -(5)
300
- - -(5)
73
149
- - -(5)
- - -(5)
40
73
- - -(5)
- - -(5)
100
300
- - -(5)
- - -(5)
232
40
450
232
100
450
- - -(5)
-continued-
15
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 9. Materials and Temperature Limits for Other Parts (continued)
TEMPERATURE CAPABILITIES
PART
_C
MATERIAL
Minimum
_F
Maximum
Minimum
Maximum
Packing flange, studs, and nuts when used with
standard bonnet
316 stainless steel
- - -(5)
- - -(5)
Metal packing box parts
316 or 17-4PH stainless steel depending
on part
- - -(5)
- - -(5)
Extension
bonnet bushing
Trims 1 & 4 416 stainless steel
Other trims 316 stainless steel
- - -(5)
29
- - -(5)
20
- - -(5)
- - -(5)
1. For high-temperature air, hydrocarbons, and certain other chemicals and solvents. Not for use with steam or ammonia. Not recommended for water above 82_C (180_F).
2. Has excellent moisture resistance to hot water and steam and may be used with most fire-resistant hydraulic oils, but cannot be used with petroleum-based fluids and other
hydrocarbons.
3. Cannot be used with fire-resistant hydraulic oils.
4. These parts not used with 137 mm (7 inch) ports or larger.
5. These materials not limiting factors.
6. This material may be used in temperatures up to 260_C (500_F) for oxidizing service.
7. Standard for NPS 8 valve regardless of cage and all NPS 1 thru 6 valves with Cavitrol III cages, optional in NPS 1 thru 6 valves with other than Cavitrol III cages.
Table 10. Fisher ET Valve Body/Trim Temperature Capabilities For All Valves Except Cavitrol III, NPS 6 ET with Whisper Trim III
Cage, and NPS 4, 6, and 8 ET with WhisperFlo Cage
BODY/BONNET(3)
MATERIALS
Cast iron
WCC steel
WC9 chrome moly steel
LCC steel
CF8M (316 stainless
steel)
MATERIAL TEMPERATURE CAPABILITY
TRIM
DESIGNATION
1, 3, 27, 29, or 57
37
37H
1
27
29
37
37H
57
1 or 3
27
29
37
37H
57
1
4
27
29
37
37H
57
27
28
29
_C
VALVE SIZE AND DESIGN
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
_F
Min
Max
Min
Max
29
29
210
29
29
29
29
210
29
29
29
29
29
210
29
29
46
46
46
46
210
29
198(4)
198(4)
198(4)
232
210
232
316(1)
316(1)
149(2)
210
316(1)
232
316(1)
316(1)
149(2)
210
316(1)
232
316(1)
210
316(1)
149(2)
210
316(1)
232
316(1)
149(2)
149(2)
20
20
410
20
20
20
20
410
20
20
20
20
20
410
20
20
50
50
50
50
410
20
325(4)
325(4)
325(4)
450
410
450
600(1)
600(1)
300(2)
410
600(1)
450
600(1)
600(1)
300(2)
410
600(1)
450
600(1)
410
600(1)
300(2)
410
600(1)
450
600(1)
300(2)
300(2)
1. Temperatures above 232_C (450_F) require PEEK anti-extrusion rings and spring-loaded seal ring. This option allows ET construction to be used up to 316_C (600_F) for
non-oxidizing service and 260_C (500_F) for oxidizing service.
2. Lubricating service allows usage to 232_C (450_F)
3. Same material also used for bottom flange, if required. Restricted trim and full-sized limits are the same.
4. May be used down to 254_C (425_F) if manufacturing process includes Charpy impact test.
16
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 11. Bonnet Selection Guidelines
BONNET STYLE
PACKING MATERIAL
IN-BODY PROCESS TEMPERATURE LIMITS(1)
_C
_F
Plain:
JStandard for all valve sizes through NPS 6 with
2-13/16 yoke boss diameter
JStandard for NPS 6 and 8 valves in cast iron and
WCC steel bonnet material with 3-9/16 yoke boss
diameter
PTFE V-ring
18 to 232
0 to 450
PTFE/Composition
18 to 232
0 to 450
Graphite ribbon/filament
0 to 316(2)
0 to 600(2)
Style 1 Cast Extension:
JStandard for NPS 8 valves in S31600 bonnet
material with 3-9/16 yoke boss diameter
PTFE V-ring
46 to 316(2)
50 to 600(2)
101 to 316(2)
150 to 600(2)
Style 2 Cast Extension:
JOptional for NPS 2 through 4 valve sizes with
2-13/16 inch yoke boss diameter
JOptional for NPS 6 and 8 valves with 3-9/16 yoke
boss diameter. Not available for NPS 8 valve in
S31600 bonnet material
PTFE/Composition
Graphite ribbon/filament
PTFE V-ring
PTFE/Composition
Graphite ribbon/filament
PTFE
For exceptional stem sealing capabilities. See
Bulletin 59.1:070, ENVIRO-SEAL Bellows Seal
Bonnets, for pressure/temperature ratings.
Graphite ULF
For exceptional stem sealing capabilities. See
Bulletin 59.1:070, ENVIRO-SEAL Bellows Seal
Bonnets, for pressure/temperature ratings.
ENVIRO-SEAL bellows seal bonnet
1. These in-body process temperatures assume an outside, ambient temperature of 21_C (70_F) and no insulation on the bonnet. When using any packing at low process temperatures,
a cast extension bonnet may have to be used to prevent packing damage which could result from the formation of valve stem frost. Material selection for trim and other components will
also be limiting factors.
2. Temperatures above 232_C (450_F) require PEEK anti-extrusion rings and spring-loaded seal ring.
Table 12. Maximum Flow Coefficients for Full-Sized Trim with
Equal Percentage Cage and Normal Flow Direction
Valve
Valve Size, NPS
Cv at Max. Valve Plug Travel
ET
1
1-1/2
2
2-1/2
3
4
6
8(1)
8(2)
17.2
35.8
59.7
99.4
136
224
394
567
819
EAT
1
2
3
4
6
1
2
3
4
6
18.5
48.1
149
152
336
19.0
47.2
148
156
328
1
1-1/2
2
2-1/2
3
4
17.2
35.8
59.7
99.4
136
224
with liner
without liner
ETR
1. With 51 mm (2 inch) travel.
2. With 76 mm (3 inch) travel.
17
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 13. Port Diameters and Valve Plug Travel
PORT
DIAMETER(1)
VALVE SIZE, NPS
ET or ETR
MAXIMUM VALVE
PLUG TRAVEL(1)
EAT
Full-Sized Trim
RestrictedCapacity Trim
Full-Sized Trim
RestrictedCapacity Trim
mm
Inch
mm
Inch
1
--1-1/2
---
1-1/2
2
--2-1/2
1
--2
---
2
-------
33.3
33.3
46.7
46.7
1.3125
1.3125
1.875
1.875
19.1
19.1
19.1
19.1
0.75
0.75
0.75
0.75
2
2-1/2
3
3
4
---
--3
4
4
6
---
58.7
73.0
87.3
2.3125
2.875
3.4375
29
38
38
1.125
1.5
1.5
---
---
6(2)
---
8(2)
---
---
---
---
111.1
4.375
51
177.8(3)
7(3)
51(3)
2(3)
136.5(4)
5.375(4)
76(4)
3(4)
51
76
203.2
---
1. For Cavitrol III trim, see table 15.
2. Not available in ETR valves.
3. Standard-travel cages.
4. Whisper Trim III cages
Table 14. Stem and Yoke Boss Diameters
VALVE SIZE, NPS
ET or ETR
STEM AND YOKE BOSS DIAMETERS
EAT
Standard
Stem
Optional
Yoke Boss
Stem
Yoke Boss
Full-Sized Trim
RestrictedCapacity Trim
Full-Sized Trim
RestrictedCapacity Trim
mm
Inch
mm
Inch
mm
Inch
mm
Inch
1
--1-1/2
---
1-1/2
2
--2-1/2
1
--2
---
2
-------
9.5
12.7
9.5
12.7
3/8
1/2
3/8
1/2
54
71
54
71
2-1/8
2-13/16
2-1/8
2-13/16
12.7
--12.7
---
1/2
--1/2
---
71
--71
---
2-13/16
--2-13/16
---
2
2-1/2
3
3
4
---
--3
4
4
6
---
12.7
12.7
12.7
1/2
1/2
1/2
71
71
71
2-13/16
2-13/16
2-13/16
19.1
19.1
19.1
3/4
3/4
3/4
90
90
90
3-9/16
3-9/16
3-9/16
---
---
12.7
1/2
71
2-13/16
19.1
3/4
90
3-9/16
25.4
127
6(1)
---
---
---
8(1)
---
---
---
25.4 or
31.8
1 or
1-1/4
127
1. Not available in ETR valves.
18
19.1
3/4
90
3-9/16
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 15. Port Diameters and Valve Plug Travel for Cavitrol III Cage
ET
VALVE SIZE, NPS
ONE-STAGE CAGE
Port Diameters
Valve Plug Travel(1)
TWO-STAGE CAGE
Port Diameters
Valve Plug Travel
mm
1
33.3
25
25.4
25
1-1/2
47.6
22
33.3
38
58.7
29
47.6
51
2-1/2
73.0
38
58.7
64
87.3
41
7.30
76
111.1
54
73.0
102
177.8
57
136.5
102
203.2
86
177.8
152
Inch
1
1.3125
1-1/2
1.875
0.875
1.3125
1.5
2.3125
1.125
1.875
2-1/2
2.875
1.5
2.3125
2.5
3.4375
1.625
2.875
4.375
2.125
2.875
2.25
5.375
3.375
1. The travel listed is the maximum travel that can be obtained for the given size. In situations where increased valve capacity is
not needed, standard ET valve travels should be utilized in selecting the actuator.
19
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 16. Port Diameters, Valve Plug Travel, Yoke Boss Diameters for TSO (Tight Shutoff) Trim
MAX TRAVEL
YOKE BOSS SIZE
PORT DIAMETER
UNBALANCE
AREA
Inch
mm
Inch
mm
Inch
mm
Inch
CV REDUCTION
AT 100%
TRAVEL(1)
76.2
90
127
3-9/16
5
73.0
2.875
68.3
2.6875
0%
0.098
CAV III 2Stage
102
90
127
3-9/16
5
73.0
2.875
68.3
2.6875
5%
0.098
EAT
NPS 4
Std
38.1
1.5
71.4
90
2-13/16
3-9/16
87.3
3.4375
82.6
3.25
6%
4%
0.118
EAT
NPS 6
Std
50.8
90
3-9/16
111
4.375
106
4.1875
4% (linear)
3% (equal percent)
0.154
VALVE
Nominal
TRIM
mm
ET
NPS 3
CAV III 2Stage
ET
NPS 4
Actual TSO
Inch2
1. This column lists the percent reduction of published maximum CV of the trim listed in the TRIM column.
FLUID TEMPERATURE, qC
FLUID TEMPERATURE, qC
0
50
100
150
200 250
100 50
110
1600
50
100
150
200 250 300
110
100
1400
70
1000
60
87C
800
50
600
40
400
30
20
200
85C
90
1200
PRESSURE DROP, PSI
80
PRESSURE DROP, BAR
1200
200
100
100
200
300
400
70
60
800
86
87
600
40
30
400
20
85
10
0
200
FLUID TEMPERATURE, qF
FOR STANDARD PTFE SEATING WITH
2 ALL BODY MATERIALS
100
100
200
300
400 500
450 4
FLUID TEMPERATURE, qF
600
FOR OPTIONAL METAL SEATING WITH
ALL BODY MATERIALS
3
TRIM 85 MAY BE USED UP TO 99 BAR (1440 PSI) WITH CLEAN DRY GAS. FOR
PROCESS FLUIDS OTHER THAN CLEAN DRY GAS, USE TRIM 85 ONLY UP TO
4 BAR (300 PSI).
21
TRIM 87 TEMPERATURE LIMITS CAN BE EXTENDED TO 316qC (600qF) FOR
NON-OXIDIZING SERVICE OR 260qC (500qF) FOR OXIDIZING SERVICE IF PEEK
ANTI-EXTRUSION RINGS ARE USED WITH SPRING-LOADED SEAL RINGS.
A6739-1/IL
Figure 15. Typical Trim for NACE MR0175 / ISO 15156 and MR0103 (Sour Service)
20
50
87
500
NOTES:
1 USE TRIM 87 INSTEAD OF TRIM 85 FOR NONLUBRICATING FLUIDS
SUCH AS SUPER-HEATED STEAM OR DRY GASES BETWEEN 149qC (300qF)
AND 232qC (450qF).
2 DO NOT EXCEED THE MAXIMUM PRESSURE AND TEMPERATURE FOR THE
PRESSURE RATING OF THE BODY MATERIAL USED, EVEN THOUGH THE TRIMS
SHOWN MAY HAVE HIGHER CAPABILITIES.
80
1000
200
10
100
1400
90
PRESSURE DROP, PSI
1600
PRESSURE DROP, BAR
100 50
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 17. Metal Trim Part Materials for Compatibility with NACE MR0175 / ISO 15156 and MR0103 (Sour Service) Specifications.
Environmental Restrictions Apply, Refer to Standard.
Trim
Designation(4)
85(5)
85C(2, 5)
86(5)
87
(Also used for
8-inch Whisper
Trim I)
87C(2)
(Also used
for 8-inch
Whisper Trim I)
Cage
Seat Ring
for Standard
Metal Seat
Construction
Optional Liner
for Metal Seat
(EAT only)
Disk Seat and
Retainer for
Optional
PTFE-Seat
Construction
S31600
S31600 with
electroless
nickel coating
(ENC)
S31600
S31600
---
S31600
S31600 with
electroless
nickel coating
(ENC)
---
---
S31600
S31600 with
seat hard faced
with CoCr-A
hardfacing alloy
S31600 with
electroless
nickel coating
(ENC)
R30006 (alloy 6)
---
---
S31600 with
electroless
nickel coating
(ENC)(3)
R30006 (alloy 6)
---
---
S31600 with
electroless
nickel coating
(ENC)(3)
---
---
S31600
Valve Plug
S31600 with
seat and guide
hard faced with
CoCr-A
hardfacing alloy
S31600 with
seat and guide
hard faced with
CoCr-A
hardfacing alloy
Valve Stem, Packing
Follower, Lantern
Ring, Packing Box
Ring, and Pin
Load
Ring(1)
S20910 (Valve Stem)
S31600 (All Other
Parts)
N05500
1. NPS 8 valve body only.
2. 85C and 87C are trims for PTFE-seat construction.
3. 8-inch Whisper Trim I cage is CB7CU-1, double H1150 (NACE) / ENC.
4. N07750 retaining ring is standard for spring-loaded seal ring construction.
5. Not for use with Whisper Trim I with 136 mm (5.375 inch) and larger ports.
Table 18. Bolting Materials and Temperature Limits for Bolting Compliance with NACE MR0175-2002, NACE MR0175/ISO 15156,
and NACE MR0103. Environmental restrictions may apply
VALVE BODY MATERIAL
TEMPERATURE CAPABILITIES
_C
BOLTING MATERIAL
_F
Min
Max
Min
Max
48(2)
427
55(2)
800
55(2)
800
Non-exposed bolting (Standard)
WCC and
CF8M
(316 SST)
Studs
Steel SA-193-B7
Nuts
Steel SA-194-2H
Exposed bolting (Optional)
May require derating of valve(1) when these body-to-bonnet bolting materials are used
WCC and
CF8M
Studs
Steel SA-193-B7M
Nuts
Steel SA-194-2HM
48(2)
427
1. Derating is not required for CL150 and 300 valves. Derating may be required for valves rated at CL600. Contact your Emerson Process Management sales office for assistance in
determining the derating of valves when these body-to-bonnet bolting materials are used.
2. 29_C (20_F) with WCC body material.
21
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 19. Fisher ET and ETR Dimensions
A
Pressure Rating, End Connection Style (1)
G (MAX)
VALVE
SIZE,
NPS
Scrd or
SW
CL125
FF or
CL150
RF
CL150
RTJ
CL250
RF or
CL300
RF
CL300
RTJ
1
1-1/2
2
210
251
286
184
222
254
197
235
267
197
235
267
210
248
282
210
251
286
210
251
289
160
200
230
2-1/2
3
4
6
8
-----------
276
298
353
451
543
292
311
365
464
556
292
317
368
473
568
308
333
384
489
584
311
337
394
508
610
314
340
397
511
613
290
310
350
480
600
1
1-1/2
2
8.25
9.88
11.25
7.25
8.75
10.00
7.75
9.25
10.50
7.75
9.25
10.50
8.25
9.75
11.12
8.25
9.88
11.25
8.25
9.88
11.38
2-1/2
3
4
6
8
-----------
10.88
11.75
13.88
17.75
21.38
11.38
12.25
14.38
18.25
21.88
11.50
12.50
14.50
18.62
22.38
12.12
13.12
15.12
19.25
23.00
12.25
13.25
15.50
20.00
24.00
12.38
13.38
15.62
20.12
24.12
BW or
CL600
RF
CL600
RTJ
PN16-40(2) PN63-100(2)
ET
ETR
230
260
300
60
71
78
119
116
133
340
380
430
550
650
90
97
129
140
191
159
168
192
-----
2.38
2.81
3.06
4.69
4.56
5.25
3.56
3.81
5.06
5.51
7.50
6.25
6.62
7.56
-----
mm
Inch
See
mm
above
See
mm
above
1. End connection style abbreviations: BW - Buttwelding, FF - Flat Faced, Scrd - Screwed, SW - Socketweld, RF - Raised Face, RTJ - Ring Type Joint
2. Valves which meet EN 1092 flange standards and have EN face-to-face dimensions are available only from Europe (EN 558-1). Valves which meet EN 1092 flange standards but
not EN face-to-face standards are available in the US. Consult your Emerson Process Management sales office.
MATCH LINE
FOR
ACTUATOR
MATCH LINE
FOR
ACTUATOR
NOTES:
A
1 B+
2
2. FOR DIMENSIONS OF
VALVES WITH OTHER END
CONNECTIONS, CONSULT
YOUR EMERSON SALES
OFFICE.
AR4967a
A09253 / IL
1
B
ET CONTROL VALVE
NOTES:
A
1 B+
2
2. FOR DIMENSIONS OF
VALVES WITH OTHER END
CONNECTIONS, CONSULT
YOUR EMERSON SALES
OFFICE.
10A7397B
A09262 / IL
1
B
ETR CONTROL VALVE
Figure 16. Fisher ET and ETR Dimensions (also see tables 19, 20, and 21)
22
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 20. Fisher ET and ETR Dimensions
D FOR PLAIN BONNET
ET Except
with Cavitrol III Two-Stage Cage
Stem Diameter, mm
VALVE
SIZE,
NPS
ET
with Cavitrol III Two-Stage Cage
Stem Diameter, mm
ETR
Stem Diameter, mm
9.5
12.7
19.1
25.4 or 31.8
9.5
12.7
19.1
25.4 or 31.8
9.5
12.7
19.1
1
1-1/2
2
2-1/2
3
127
124
-------
149
146
165
187
191
----162
184
187
-----------
--155
-------
184
177
201
229
260
----198
226
256
-----------
113
122
-------
124
133
148
157
167
----140
152
159
4
6(1)
6(2)
8
---------
221
-------
217
251
312
375(3)
238
270
330
426
---------
311
-------
308
336
--511
354
380
--560
198
191
--------------------Stem Diameter, Inch
Stem Diameter, Inch
Stem Diameter, Inch
3/8
1/2
3/4
1 or 1-1/4
3/8
1/2
3/4
1 or 1-1/4
3/8
1/2
3/4
1
1-1/2
2
2-1/2
3
5.00
4.88
-------
5.88
5.75
6.50
7.38
7.50
----6.38
7.25
7.38
-----------
--6.09
-------
7.25
6.97
7.91
9.03
10.22
----7.78
8.91
10.09
-----------
4.44
4.81
-------
4.88
5.25
5.81
6.31
6.56
----5.50
6.00
6.25
4
6(1)
6(2)
8
---------
8.69
-------
8.56
9.88
12.26
14.75(3)
9.38
10.62
13.00
16.75
---------
12.25
-------
12.12
13.22
--20.12
13.94
14.97
--22.06
---------
7.81
-------
7.50
-------
1. All except Whisper Trim III and WhisperFlo cages.
2. Whisper Trim III and WhisperFlo cages.
3. Available only in cast iron or WCC steel for the stem diameter with plain bonnet.
Table 21. Fisher ET and ETR Dimensions
D FOR EXTENSION AND ENVIRO-SEAL BELLOWS SEAL BONNETS
(ET ONLY, EXCEPT WITH CAVITROL III CAGE)
VALVE
SIZE,
NPS
Style 1 Ext. Bonnet
ENVIRO-SEAL Bellows Seal
Bonnet
Stem diameter
Style 2 Ext. Bonnet
Stem Diameter
Stem Diameter
mm
9.5
12.7
19.1
25.4 or 31.8
9.5
12.7
19.1
9.5
12.7
19.1
1
1-1/2
2
2-1/2
3
213
210
-------
251
248
267
289
292
----272
294
297
-----------
303
300
-------
319
316
465
492
495
--------487
320
317
-------
----384
--517
--------517
4
6(1)
6(2)
8
---------
322
-------
327
357
418
421
370
402
462
450
---------
526
-------
518
543
604
621
---------
541
-------
--573
--703
3/8
1/2
3/4
1 or 1-1/4
3/8
1/2
3/4
3/8
1/2
3/4
1
1-1/2
2
2-1/2
3
8.38
8.25
-------
9.88
9.75
10.50
11.38
11.50
----10.69
11.56
11.69
-----------
11.94
11.81
-------
12.56
12.44
18.31
19.38
19.50
--------19.19
12.62
12.50
-------
----15.12
--20.38
--------20.38
4
6(1)
6(2)
8
---------
12.69
-------
12.88
14.06
16.44
16.56
14.56
15.81
18.19
17.75
---------
20.69
-------
20.38
21.38
23.76
24.44
---------
21.31
-------
--22.56
--27.69
Inch
1. Standard-travel cages.
2. Whisper Trim III and WhisperFlo cages.
23
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 22. Fisher EAT Dimensions(1)
VALVE
SIZE,
NPS
Table 23. Fisher EAT Dimensions
AA
CL150
RF
RTJ
CL300
RF
RTJ
DD
CL600
BW, SW or RF
RTJ
mm
1
2
3
4
6
92
127
149
176
225
98
133
156
183
232
98
133
159
184
237
105
141
167
197
244
105
143
168
197
254
105
144
170
198
256
4.12
5.62
6.62
7.75
10.00
4.12
5.69
6.69
7.81
10.0
6
Inch
1
2
3
4
6
3.62
5.00
5.88
6.94
8.88
3.88
5.25
6.12
7.19
9.12
3.88
5.25
6.25
7.25
9.31
4.12
5.56
6.56
7.56
9.62
1. End connection style abbreviations: BW - Buttwelding, FF - Flat Faced,
Scrd - Screwed, SW - Socketweld, RF - Raised Face, RTJ - Ring Type Joint.
VALVE
SIZE,
NPS
1
2
3
4
6
Plain Bonnet
Style 1 Extension
Bonnet
Stem Diameter, mm
Stem Diameter,
mm
9.5
12.7
19.1
25.4 or
38.1
9.5
12.7
19.1
111
98
-------
133
121
149
140
144
----146
137
141
--------187
197
184
-------
253
223
251
241
246
----256
246
251
Stem Diameter, In.
1
2
3
4
6
Stem Diameter, In.
3/8
1/2
3/4
1 or 1-1/4
3/8
1/2
3/4
4.38
3.88
-------
5.25
4.75
5.88
5.50
5.69
----5.75
5.38
5.56
--------7.38
7.75
7.25
-------
9.95
8.75
9.88
9.50
9.69
----10.06
9.69
9.88
MATCH LINE
FOR
ACTUATOR
Table 24. Fisher EAT Dimensions
DD
DD
NOTE:
FOR DIMENSIONS OF
VALVES WITH PN (OR
OTHER) END CON
NECTIONS, CONSULT
YOUR EMERSON SALES
OFFICE.
AA
VALVE
SIZE,
NPS
1
2
3
4
6
Style 2 Extension
Bonnet
Stem Diameter, mm
Stem Diameter, mm
9.5
12.7
19.1
9.5
12.7
19.1
291
278
-------
305
291
454
445
449
------437
441
305
292
-------
------467
465
-----------
Stem Diameter, In.
AA
A09272
Figure 17. Fisher EAT Dimensions (also see tables 22, 23,
and 24)
24
1
2
3
4
6
ENVIRO-SEAL
Bellows Seal Bonnet
Stem Diameter, In.
3/8
1/2
3/4
3/8
1/2
3/4
11.44
10.94
-------
12.00
11.44
17.88
17.50
17.69
------17.19
17.38
12.00
11.50
-------
------18.38
18.31
-----------
Product Bulletin
51.1:ET
April 2011
ET Valve
Ordering Information
a. Minimum flowing drop
Inlet pressure and temperature must always be
limited by the applicable ASME
pressure/temperature rating. Pressure drop
information for various trim material combinations is
provided in figures 12, 13, and 15. The maximum
allowable pressure drop for the application must not
exceed the lowest value indicated for the
combination of materials selected.
b. Normal flowing drop
c. Maximum flowing drop
d. Maximum at shutoff
7. Flow rates:
a. Minimum controlled flow
When ordering, specify:
b. Normal flow
Application Information
1. Type of application:
c. Maximum flow
8. Maximum permissible noise level, if critical
a. Throttling or on-off
9. Shutoff classification required
b. Reducing or relief
10. Valve stem diameter and bonnet type (plain,
extension, or ENVIRO-SEAL bellows seal bonnet)
2. Controlled fluid (include chemical analysis of fluid
if possible)
3. Specific gravity of controlled fluid
4. Fluid temperature
5. Inlet pressures:
a. Minimum
11. Line size and schedule
Valve Information
To determine what valve ordering information is
needed, refer to the specifications. Review the
description for each specification and in the
referenced tables; write down your choice whenever
there is a selection to be made. Always specify the
valve design letter designation.
b. Normal
c. Maximum
6. Pressure drops:
Actuator and Accessory Information
Refer to the specific actuator and accessory bulletins
for required ordering information.
25
Product Bulletin
51.1:ET
April 2011
ET Valve
Coefficients
Table 25. Fisher EAT, Quick Opening Cage, With Liner
Quick Opening
Characteristic
With Liner
Valve
Size, NPS
Port Diameter
Maximum
Travel(1)
mm
Inches
mm
Inches
33.3
0.3125
19
0.75
47.6
1.875
19
0.75
2
33.3
1.3125
(4)
(4)
73.0
2.875
19
38
0.75
1.5
3
47.6
1.875
(4)
(4)
87.3
3.4375
19
38
0.75
1.5
4
58.7
2.3125
(4)
(4)
111.1
4.375
29
51
1.125
6
73.0
2.875
(4)
(4)
38
1.5
Flow
Coefficient
Coeffs.
for 6
mm
(0.25 in)
Travel(2)
Cv
Kv
Valve OpeningPercent of Total Travel
FL(3)
10
20
30
40
50
60
70
80
90
100
14.2
5.14
9.24
13.1
16.2
18.8
20.9
22.4
23.4
24.0
24.0
0.90
12.3
4.45
7.99
11.3
14.0
16.3
18.1
19.4
20.2
20.8
20.8
---
XT
0.800
0.629 0.703 0.761 0.809 0.775 0.713 0.677 0.652 0.630 0.630
Cv
29.4
8.77
17.1
26.2
36.1
45.4
53.4
59.3
63.6
67.3
70.7
0.76
14.8
22.7
31.2
39.3
46.2
51.3
55.0
58.2
61.2
---
Kv
25.4
7.59
XT
0.573
0.480 0.513 0.568 0.570 0.577 0.589 0.628 0.618 0.656 0.656
Cv
17.3
5.91
10.1
15.1
21.7
29.4
37.3
43.7
48.5
52.4
55.2
0.60
5.11
8.74
13.1
18.8
25.4
32.3
37.8
42.0
45.3
47.7
---
---
Kv
15.0
XT
0.543
0.404 0.584 0.570 0.522 0.478 0.431 0.396 0.370 0.344 0.326
Cv
30.6
24.2
47.2
77.8
108
133
148
159
171
181
183
0.76
40.8
67.3
93.4
115
128
138
148
157
158
---
---
Kv
26.5
20.9
XT
0.540
0.517 0.534 0.504 0.545 0.582 0.636 0.651 0.616 0.575 0.569
Cv
29.8
7.96
15.5
25.7
37.4
49.0
61.2
72.5
83.1
92.8
102
0.60
13.4
22.2
32.4
42.4
52.9
62.7
71.9
80.3
88.2
---
---
Kv
25.8
6.89
XT
0.576
0.549 0.624 0.603 0.541 0.525 0.482 0.452 0.422 0.391 0.349
Cv
37.1
22.3
46.3
77.1
117
155
180
197
212
230
235
0.72
40.0
66.7
101
134
156
170
183
199
203
---
---
Kv
32.1
19.3
XT
0.580
0.616 0.547 0.537 0.531 0.529 0.575 0.629 0.635 0.609 0.620
Cv
31.4
14.4
28.3
46.1
66.7
87.5
107
124
138
149
160
0.61
24.5
39.9
57.7
75.7
92.6
107
119
129
138
---
---
Kv
27.2
12.5
XT
0.548
0.509 0.533 0.505 0.486 0.482 0.465 0.443 0.416 0.387 0.354
Cv
50.0
39.8
84.0
150
219
279
332
379
420
435
435
0.71
72.7
130
189
241
287
328
363
376
376
---
---
Kv
43.3
34.4
XT
0.578
0.597 0.599 0.577 0.581 0.581 0.578 0.565 0.527 0.533 0.533
Cv
38.7
23.9
47.1
74.9
109
142
174
201
219
244
248
0.59
40.7
64.8
94.3
123
151
174
189
211
215
---
Kv
33.5
20.7
XT
0.353
0.353 0.353 0.353 0.353 0.356 0.352 0.353 0.352 0.353 0.354
1. When using 655-EAT as a control valve for on-off service, the maximum travel for sizing purposes is 19 mm (0.75 inch).
2. When sizing self-operated regulators, use coefficients listed for 6 mm (0.25 inch) travel.
3. At 100% travel.
4. Restricted trim.
26
---
---
---
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 26. Fisher EAT, Quick Opening Cage, Without Liner
Quick Opening
Characteristic
Without Liner
Valve
Size,
NPS
Port Diameter
mm
33.3
47.6
Inches
0.3125
1.875
Maximum
Travel(1)
mm
19
19
Inches
0.75
0.75
2
33.3
1.3125
(4)
(4)
73.0
2.875
19
38
0.75
1.5
3
47.6
1.875
(4)
(4)
87.3
3.4375
19
38
0.75
1.5
4
58.7
2.3125
(4)
(4)
111.1
4.375
29
51
1.125
6
73.0
2.875
(4)
(4)
38
1.5
Flow
Coefficient
Coeffs. for
6 mm
(0.25 in)
Travel(2)
10
20
30
40
50
60
70
80
90
100
Cv
14.8
5.07
9.36
13.6
16.8
19.2
20.9
22.2
23.1
23.6
23.7
0.87
Kv
12.8
4.39
8.10
11.8
14.5
16.6
18.1
19.2
20.0
20.4
20.5
---
XT
0.757
0.638 0.753 0.753 0.766 0.736 0.703 0.670 0.650 0.640 0.636
Cv
28.0
8.06
15.7
24.9
34.3
43.1
51.0
57.1
61.4
64.6
67.2
0.87
13.6
21.5
29.7
37.3
44.1
49.4
53.1
55.9
58.1
---
Valve OpeningPercent of Total Travel
FL(3)
---
Kv
24.2
6.97
XT
0.629
0.531 0.621 0.623 0.631 0.641 0.638 0.656 0.676 0.686 0.682
Cv
17.2
6.02
10.4
15.4
20.9
27.1
33.7
38.5
41.7
44.2
45.6
0.71
9.00
13.3
18.1
23.4
29.2
33.3
36.1
38.2
39.4
---
---
Kv
14.9
5.21
XT
0.573
0.470 0.541 0.570 0.575 0.563 0.526 0.510 0.492 0.476 0.470
Cv
39.2
23.4
47.9
78.7
108
128
142
153
163
171
171
0.81
41.4
68.1
93.4
111
123
132
141
148
148
---
---
Kv
33.9
20.2
XT
0.576
0.588 0.573 0.534 0.573 0.635 0.662 0.654 0.626 0.600 0.605
Cv
29.1
8.27
15.9
25.6
36.0
46.8
56.4
64.6
72.1
79.3
86.1
0.72
13.8
22.1
31.1
40.5
48.8
55.9
62.4
68.6
74.5
---
---
Kv
25.2
7.15
XT
0.609
0.488 0.603 0.610 0.594 0.575 0.574 0.569 0.561 0.530 0.490
Cv
39.0
23.9
48.2
80.3
118
151
178
195
209
223
223
0.76
41.7
69.5
102
131
154
169
181
193
193
---
---
Kv
33.7
20.7
XT
0.562
0.588 0.566 0.554 0.556 0.580 0.610 0.659 0.669 0.644 0.650
Cv
30.9
13.6
27.0
43.9
62.5
80.6
96.0
109
120
127
133
0.73
11.8
23.4
38.0
54.1
69.7
83.0
94.3
104
110
115
---
---
Kv
26.7
XT
0.608
0.593 0.614 0.582 0.578 0.587 0.590 0.576 0.547 0.533 0.513
Cv
45.8
37.6
79.6
142
207
265
311
351
383
398
398
0.76
68.9
123
179
229
269
304
331
344
344
---
---
Kv
39.6
32.5
XT
0.652
0.680 0.652 0.639 0.639 0.655 0.686 0.683 0.666 0.657 0.667
Cv
35.4
21.8
43.1
71.5
103
130
154
173
188
198
206
0.74
37.3
61.8
89.1
112
133
150
163
171
178
---
Kv
30.6
18.9
XT
0.671
0.624 0.650 0.652 0.618 0.659 0.659 0.646 0.620 0.595 0.568
---
---
1. When using 655-EAT as a control valve for on-off service, the maximum travel for sizing purposes is 19 mm (0.75 inch).
2. When sizing self-operated regulators, use coefficients listed for 6 mm (0.25 inch) travel.
3. At 100% travel.
4. Restricted trim.
27
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 27. Fisher EAT, Linear Cage, With Liner
With Liner - Flow Down
Valve
Size,
NPS
1
Port Diameter
Maximum
Travel
mm
Inches
mm
Inches
33.3
1.3125
19
0.75
47.6
1.875
19
0.75
2
33.3
1.3125
(2)
(2)
73.0
2.875
19
38
0.75
1.5
3
47.6
1.875
(2)
(2)
87.3
3.4375
19
38
0.75
1.5
4
58.7
2.3125
(2)
(2)
111.1
4.375
29
51
1.125
6
73.0
2.875
(2)
(2)
1. At 100% travel.
2. Restricted trim.
28
38
1.5
Linear
Characteristic
Flow
Coefficient
10
20
30
40
50
60
70
80
90
100
Cv
2.71
5.17
8.14
10.7
13.0
15.2
17.2
19.1
20.7
22.0
0.90
Kv
2.34
4.47
7.04
9.26
11.2
13.1
14.9
16.5
17.9
19.0
---
XT
0.632
0.692
0.719
0.772
0.786
0.777
0.755
0.722
0.682
0.634
---
Cv
3.77
6.94
11.3
16.1
21.0
26.7
33.1
40.1
46.8
53.8
0.82
---
Valve OpeningPercent of Total Travel
FL(1)
Kv
3.26
6.00
9.77
13.9
18.2
23.1
28.6
34.7
40.5
46.5
XT
0.665
0.675
0.663
0.642
0.627
0.616
0.617
0.607
0.633
0.661
---
Cv
2.95
5.49
8.65
12.1
15.7
19.3
23.4
29.7
35.7
41.0
0.66
---
Kv
2.55
4.75
7.48
10.5
13.6
16.7
20.2
25.7
30.9
35.5
XT
0.474
0.592
0.587
0.581
0.579
0.584
0.564
0.487
0.451
0.426
---
Cv
10.3
24.0
38.8
54.3
69.8
86.5
102
124
141
155
0.80
---
Kv
8.91
20.8
33.6
47.0
60.4
74.8
88.2
107
122
134
XT
0.630
0.623
0.618
0.598
0.599
0.591
0.619
0.603
0.614
0.614
---
Cv
3.37
6.45
10.6
15.3
19.8
25.3
32.2
40.1
48.4
58.1
0.74
---
Kv
2.92
5.58
9.17
13.2
17.1
21.9
27.9
34.7
41.9
50.3
XT
0.630
0.682
0.693
0.665
0.663
0.637
0.600
0.588
0.569
0.548
---
Cv
12.7
31.6
54.1
77.8
103
128
149
171
191
208
0.78
---
Kv
11.0
27.3
46.8
67.3
89.1
111
129
148
165
180
XT
0.677
0.638
0.596
0.590
0.552
0.548
0.573
0.594
0.613
0.627
---
Cv
6.70
15.3
25.2
37.0
50.2
64.5
79.4
94.6
110
124
0.66
---
Kv
5.80
13.2
21.8
32.0
43.4
55.8
68.7
81.8
95.2
107
XT
0.705
0.590
0.596
0.573
0.536
0.509
0.493
0.490
0.471
0.445
---
Cv
25.4
53.6
83.0
113
146
179
218
263
309
350
0.78
---
Kv
22.0
46.4
71.8
97.7
126
155
189
227
267
303
XT
0.670
0.666
0.666
0.659
0.631
0.627
0.623
0.624
0.630
0.617
---
Cv
10.6
25.2
41.1
57.7
76.1
94.8
116
139
168
195
0.67
Kv
9.17
21.8
35.6
49.9
65.8
82.0
100
120
145
169
---
XT
0.445
0.443
0.448
0.445
0.445
0.445
0.443
0.448
0.442
0.444
---
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 28. Fisher EAT, Linear Cage, Without Liner
Without Liner - Flow Down
Port
Diameter
Maximum
Travel
Valve
Size,
NPS
mm
Inches
mm
Inches
33.3
1.3125
19
0.75
47.6
1.875
19
0.75
2
33.3
1.3125
(2)
(2)
73.0
2.875
19
38
0.75
1.5
3
47.6
1.875
(2)
(2)
87.3
3.4375
19
38
0.75
1.5
4
58.7
2.3125
(2)
(2)
111.1
4.375
29
51
1.125
6
73.0
2.875
(2)
(2)
38
1.5
Linear
Characteristic
Flow
Coefficient
10
20
30
Cv
2.90
5.78
Kv
2.51
5.00
XT
0.778
Cv
3.68
Valve OpeningPercent of Total Travel
FL(1)
40
50
60
70
80
90
100
8.85
11.6
13.9
16.0
18.0
19.7
21.2
22.3
0.89
7.66
10.0
12.0
13.8
15.6
17.0
18.3
19.3
---
0.704
0.699
0.736
0.745
0.747
0.730
0.699
0.664
0.624
---
6.98
11.3
15.9
20.8
26.4
32.7
39.2
45.7
52.5
0.84
---
Kv
3.18
6.04
9.77
13.8
18.0
22.8
28.3
33.9
39.5
45.4
XT
0.676
0.667
0.684
0.666
0.624
0.627
0.632
0.625
0.655
0.679
---
Cv
3.01
5.45
8.95
12.5
15.9
19.1
23.3
28.4
33.2
37.6
0.73
---
Kv
2.60
4.71
7.74
10.8
13.8
16.5
20.2
24.6
28.7
32.5
XT
0.790
0.768
0.661
0.618
0.608
0.611
0.582
0.545
0.535
0.516
---
Cv
10.9
25.1
41.3
58.4
75.7
93.9
112
128
143
153
0.83
---
Kv
9.43
21.7
35.7
50.5
65.5
81.2
96.9
111
124
132
XT
0.736
0.638
0.591
0.548
0.538
0.532
0.543
0.583
0.619
0.631
---
Cv
3.61
6.92
11.1
15.5
20.6
26.4
33.2
41.4
50.1
60.2
0.78
---
Kv
3.12
5.99
9.60
13.4
17.8
22.8
28.7
35.8
43.3
52.1
XT
0.623
0.721
0.694
0.684
0.663
0.630
0.602
0.570
0.568
0.546
---
Cv
14.0
33.8
56.3
80.2
104
127
148
169
185
201
0.81
---
Kv
12.1
29.2
48.7
69.4
90.0
110
128
146
160
174
XT
0.640
0.638
0.611
0.588
0.570
0.568
0.593
0.622
0.660
0.664
---
Cv
7.02
15.7
25.7
36.9
48.6
60.9
72.9
84.6
97.2
108
0.76
---
Kv
6.07
13.6
22.2
31.9
42.0
52.7
63.1
73.2
84.1
93.4
XT
0.712
0.626
0.625
0.597
0.587
0.577
0.590
0.604
0.580
0.566
---
Cv
24.2
51.2
81.8
109
140
171
208
256
300
341
0.78
---
Kv
20.9
44.3
70.8
94.3
121
148
180
221
260
295
XT
0.643
0.697
0.666
0.693
0.672
0.668
0.684
0.663
0.668
0.662
---
Cv
10.2
22.8
36.6
52.1
68.0
84.5
102
124
147
168
0.74
Kv
8.82
19.7
31.7
45.1
58.8
73.1
88.2
107
127
145
---
XT
0.592
0.651
0.661
0.635
0.619
0.619
0.615
0.584
0.568
0.556
---
1. At 100% travel.
2. Restricted trim.
29
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 29. Fisher EAT, Equal Percentage Cage, With Liner
With Liner - Flow Down
Port
Diameter
Maximum
Travel
Valve
Size,
NPS
mm
Inches
mm
Inches
33.3
1.3125
19
0.75
47.6
1.875
19
0.75
2
33.3
1.3125
(2)
(2)
73.0
2.875
19
38
0.75
1.5
3
47.6
1.875
(2)
(2)
87.3
3.4375
19
38
0.75
1.5
4
58.7
2.3125
(2)
(2)
111.1
4.375
29
51
1.125
6
73.0
2.875
(2)
(2)
1. At 100% travel.
2. Restricted trim.
30
38
1.5
Equal Percentage
Characteristic
Flow
Coefficient
Valve OpeningPercent of Total Travel
10
20
30
40
50
60
70
Cv
1.02
1.49
2.07
2.70
3.92
5.68
Kv
0.882
1.29
1.79
2.34
3.39
4.91
XT
0.902
0.902
0.820
0.740
0.741
Cv
1.44
2.38
3.54
5.10
7.60
FL(1)
80
90
100
8.18
11.7
15.5
18.5
0.93
7.08
10.1
13.4
16.0
---
0.737
0.738
0.734
0.742
0.739
---
11.6
18.1
26.9
37.8
48.1
0.83
---
Kv
1.25
2.06
3.06
4.41
6.57
10.0
15.7
23.3
32.7
41.6
XT
0.619
0.649
0.671
0.678
0.666
0.639
0.574
0.578
0.578
0.576
---
Cv
0.792
1.28
1.84
2.56
3.78
5.66
8.64
13.3
19.9
27.6
0.75
---
Kv
0.685
1.11
1.59
2.21
3.27
4.90
7.47
11.5
17.2
23.9
XT
0.648
0.654
0.682
0.659
0.683
0.661
0.592
0.534
0.479
0.468
---
Cv
4.38
7.99
12.1
16.5
24.2
36.5
56.6
85.9
116
151
0.78
---
Kv
3.79
6.91
10.5
14.3
20.9
31.6
49.0
74.3
100
131
XT
0.783
0.746
0.680
0.652
0.620
0.588
0.551
0.525
0.553
0.550
---
Cv
1.31
2.28
3.48
5.05
7.58
11.9
18.2
26.7
38.4
50.5
0.78
---
Kv
1.13
1.97
3.01
4.37
6.56
10.3
15.7
23.1
33.2
43.7
XT
0.804
0.758
0.719
0.725
0.696
0.634
0.637
0.611
0.561
0.530
---
Cv
2.31
0.470
7.45
11.3
17.8
28.7
47.9
77.5
112
152
0.81
---
Kv
2.00
0.41
6.44
9.77
15.4
24.8
41.4
67.0
96.9
131
XT
0.780
0.780
0.791
0.726
0.652
0.630
0.565
0.546
0.549
0.545
---
Cv
2.24
3.67
5.44
7.81
11.7
17.9
27.6
41.9
62.6
86.3
0.73
---
Kv
1.94
3.17
4.71
6.76
10.1
15.5
23.9
36.2
54.1
74.6
XT
0.630
0.668
0.662
0.672
0.659
0.610
0.593
0.574
0.500
0.456
---
Cv
5.54
11.0
18.1
30.9
51.7
84.3
136
205
276
336
0.74
---
Kv
4.79
9.52
15.7
26.7
44.7
72.9
118
177
239
291
XT
0.727
0.684
0.657
0.624
0.599
0.585
0.590
0.587
0.573
0.576
---
Cv
1.32
3.73
7.20
11.1
17.5
27.6
43.4
67.8
102
147
0.74
Kv
1.14
3.23
6.23
9.60
15.1
23.9
37.5
58.6
88.2
127
---
XT
0.455
0.458
0.454
0.457
0.453
0.454
0.454
0.455
0.454
0.454
---
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 30. Fisher EAT, Equal Percentage Cage, Without Liner
Without Liner - Flow Down
Port
Diameter
Maximum
Travel
Valve
Size,
NPS
mm
Inches
mm
Inches
33.3
1.3125
19
0.75
47.6
1.875
19
0.75
2
33.3
1.3125
(2)
(2)
73.0
2.875
19
38
0.75
1.5
3
47.6
1.875
(2)
(2)
87.3
3.4375
19
38
0.75
1.5
4
58.7
2.3125
(2)
(2)
111.1
4.375
29
51
1.125
6
73.0
2.875
(2)
(2)
38
1.5
Flow
Coefficient
Equal Percentage
Characteristic
Valve OpeningPercent of Total Travel
FL(1)
10
20
30
40
50
60
70
80
90
100
Cv
1.08
1.62
2.20
2.96
4.18
6.04
8.74
12.5
16.5
19.0
0.91
Kv
0.934
1.40
1.90
2.56
3.62
5.22
7.56
10.8
14.3
16.4
---
XT
0.912
0.860
0.808
0.771
0.742
0.706
0.693
0.699
0.697
0.694
---
Cv
1.67
2.60
3.82
5.43
7.79
12.2
18.9
27.4
37.8
47.2
0.85
---
Kv
1.44
2.25
3.30
4.70
6.74
10.6
16.3
23.7
32.7
40.8
XT
0.680
0.690
0.702
0.725
0.707
0.619
0.622
0.621
0.619
0.623
---
Cv
1.11
1.55
2.05
2.87
4.07
5.95
8.84
13.4
19.6
26.8
0.79
---
Kv
0.960
1.34
1.77
2.48
3.52
5.15
7.65
11.6
17.0
23.2
XT
0.938
0.899
0.848
0.789
0.761
0.692
0.636
0.568
0.519
0.507
---
Cv
4.59
8.29
12.0
16.9
25.0
37.7
57.3
85.1
121
148
0.80
---
Kv
3.97
7.17
10.4
14.6
21.6
32.6
49.6
73.6
105
128
XT
0.779
0.744
0.715
0.684
0.630
0.582
0.583
0.579
0.578
0.580
---
Cv
1.56
2.51
3.68
5.40
7.65
11.7
18.2
27.0
37.3
47.8
0.84
---
Kv
1.35
2.17
3.18
4.67
6.62
10.1
15.7
23.4
32.3
41.3
XT
0.834
0.807
0.768
0.718
0.756
0.723
0.679
0.627
0.615
0.615
---
Cv
2.51
5.10
8.03
12.0
18.7
30.7
47.4
80.3
116
156
0.81
---
Kv
2.17
4.41
6.95
10.4
16.2
26.6
41.0
69.5
100
135
XT
0.890
0.770
0.744
0.701
0..696
0.637
0.668
0.572
0.566
0.565
---
Cv
2.33
3.56
5.64
8.18
11.9
18.0
28.2
42.6
62.2
81.8
0.79
---
Kv
2.02
3.08
4.88
7.08
10.3
15.6
24.4
36.8
53.8
70.8
XT
0.753
0.846
0.702
0.666
0.682
0.656
0.619
0.609
0.559
0.530
---
Cv
5.51
10.9
17.9
30.2
50.5
82.0
133
200
269
328
0.78
---
Kv
4.77
9.43
15.5
26.1
43.7
70.9
115
173
233
284
XT
0.705
0.701
0.663
0.646
0.612
0.604
0.606
0.605
0.596
0.604
---
Cv
4.00
7.63
11.1
15.0
23.3
35.0
53.3
79.6
112
144
0.78
Kv
3.46
6.60
9.60
13.0
20.2
30.3
46.1
68.9
96.9
125
---
XT
0.670
0.698
0.725
0.731
0.637
0.629
0.599
0.597
0.573
0.571
---
1. At 100% travel.
2. Restricted trim.
31
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 31. Fisher EAT, Whisper Trim I Cage
Whisper Trim I - Flow Up
Valve
Size,
NPS
1
32
Port
Diameter
mm
33.3
47.6
73.0
87.3
111.1
Inches
1.3125
1.875
2.875
3.4375
4.375
Maximum
Travel
mm
19
19
38
38
51
Inches
0.75
0.75
1.5
1.5
Linear
Characteristic
Flow
Coefficient
10
20
30
40
50
60
70
80
90
100
Cv
2.17
5.30
8.44
11.8
14.7
16.6
19.5
21.5
23.1
24.1
Valve OpeningPercent of Total Travel
Kv
1.88
4.58
7.30
10.2
12.7
14.4
16.9
18.6
20.0
20.8
XT
0.390
0.406
0.424
0.454
0.456
0.490
0.490
0.506
0.526
0.536
Cv
4.98
11.0
19.7
27.9
34.5
40.6
45.7
50.1
53.7
55.9
Kv
4.31
9.52
17.0
24.1
29.8
35.1
39.5
43.3
46.5
48.4
XT
0.670
0.633
0.403
0.330
0.322
0.327
0.343
0.359
0.372
0.386
Cv
12.4
30.4
48.3
67.6
84.2
95.2
112
123
132
138
Kv
10.7
26.3
41.8
58.5
72.8
82.3
96.9
106
114
119
XT
0.307
0.303
0.330
0.329
0.332
0.331
0.361
0.360
0.360
0.375
Cv
16.7
42.9
67.5
91.2
113
133
152
168
182
194
Kv
14.4
37.1
58.4
78.9
97.7
115
131
145
157
168
XT
0.738
0.411
0.378
0.331
0.323
0.342
0.354
0.370
0.391
0.400
Cv
28.8
70.4
112
157
195
220
260
285
310
320
Kv
24.9
60.9
96.9
136
169
190
225
247
268
277
XT
0.303
0.331
0.361
0.330
0.330
0.360
0.360
0.390
0.391
0.403
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 32. Fisher ET, CL125-600, Quick Opening Cage
Quick Opening
Characteristic
Quick Opening
Port
Diameter
Maximum
Travel(1)
Valve
Size,
NPS
mm
Inches
mm
Inches
33.3
1.3125
19
0.75
47.6
1.875
19
0.75
1-1/2
33.3
1.3125
(4)
(4)
58.7
2.3125
19
29
0.75
1.125
2
33.3
1.3125
(4)
(4)
73.0
2.875
19
38
0.75
1.5
2-1/2
47.6
1.875
(4)
(4)
87.3
3.4375
19
38
0.75
1.5
3
58.7
2.3125
(4)
(4)
29
1.125
10
20
30
40
50
60
70
80
90
100
Cv
Coeffs
for 6 mm
(0.25 In)
Travel(2)
14.7
4.86
9.39
13.4
16.9
18.9
20.3
21.1
21.8
21.9
22.1
0.81
Kv
12.7
4.20
8.12
11.6
14.6
16.3
17.6
18.3
18.9
18.9
19.1
---
XT
0.703
0.556 0.744 0.724 0.666 0.626 0.584 0.566 0.549 0.554 0.556
Cv
22.6
7.79
14.4
20.5
26.8
32.0
36.6
39.4
41.3
42.7
44.0
0.79
12.5
17.7
23.2
27.7
31.7
34.1
35.7
36.9
Flow
Coefficient
Valve OpeningPercent of Total Travel
FL(3)
---
Kv
19.5
6.74
38.1
---
XT
0.679
0.494 0.641 0.682 0.680 0.686 0.661 0.649 0.638 0.616 0.597
---
Fd
---
0.22
0.28
0.32
0.34
0.35
0.36
0.36
0.36
0.36
0.36
---
Cv
16.2
5.05
9.99
14.7
20.0
24.0
25.7
26.2
27.4
28.6
29.9
0.88
8.64
12.7
17.3
20.8
22.2
22.7
23.7
24.7
25.9
---
Kv
14.0
4.37
XT
0.942
0.803 0.904 0.946 0.872 0.838 0.849 0.874 0.832 0.795 0.756
Cv
29.7
13.4
26.8
39.9
51.3
62.9
70.6
73.7
75.6
76.8
77.6
0.77
11.6
23.2
34.5
44.4
54.4
61.1
63.8
65.4
66.4
67.1
---
0.605 0.695 0.737 0.761 0.703 0.658 0.641 0.635 0.626 0.623
---
---
Kv
25.7
XT
0.773
Fd
---
0.24
0.30
0.33
0.35
0.36
0.36
0.36
0.36
0.36
0.36
---
Cv
16.7
4.80
9.58
14.9
20.2
25.7
29.3
31.2
31.2
31.2
31.2
0.87
8.29
12.9
17.5
22.2
25.3
27.0
27.0
27.0
27.0
---
Kv
14.4
4.15
XT
0.705
0.578 0.733 0.695 0.698 0.666 0.689 0.735 0.791 0.805 0.805
Cv
33.4
20.9
39.6
58.8
74.2
84.9
97.0
103
106
108
109
0.81
34.3
50.9
64.2
73.4
83.9
89.1
91.7
93.4
---
Kv
28.9
18.1
94.3
---
XT
0.635
0.601 0.684 0.738 0.767 0.744 0.689 0.669 0.658 0.660 0.652
---
Fd
---
0.25
0.31
0.34
0.35
0.36
0.36
0.36
0.36
0.36
0.35
---
Cv
25.3
7.83
15.2
22.8
31.0
40.0
48.3
54.9
60.3
66.4
71.2
0.86
13.1
19.7
26.8
34.6
41.8
47.5
52.2
57.4
61.6
---
Kv
21.9
6.77
XT
0.642
0.498 0.618 0.627 0.636 0.640 0.669 0.725 0.758 0.737 0.710
Cv
43.6
27.2
52.2
77.9
99.5
124
140
149
154
158
161
0.77
45.2
67.4
86.1
107
121
129
133
137
139
---
---
Kv
37.7
23.5
XT
0.635
0.626 0.671 0.745 0.796 0.703 0.657 0.619 0.602 0.591 0.577
Fd
---
0.22
0.29
0.32
0.34
0.35
0.36
0.36
0.36
0.36
0.36
---
Cv
35.2
15.9
31.7
47.2
60.7
74.4
83.6
87.3
89.5
91.0
91.9
0.86
27.4
40.8
52.5
64.4
72.3
75.5
77.4
78.7
---
Kv
30.4
13.8
79.5
---
XT
0.852
0.718 0.837 0.889 0.905 0.842 0.784 0.763 0.760 0.744 0.744
---
-continued-
33
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 32. Fisher ET, CL125-600, Quick Opening Cage (continued)
Valve
Size,
NPS
Port
Diameter
mm
111.1
Inches
4.375
Maximum
Travel(1)
mm
51
Inches
4
73.0
2.875
(4)
(4)
177.8
38
51
1.5
111.1
4.375
(4)
(4)
203.2
203.2
51
51
76
10
20
30
40
50
60
70
80
90
100
Cv
Coeffs
for 6 mm
(0.25 In)
Travel(2)
45.9
37.7
75.0
125
163
193
220
238
247
251
251
0.79
Kv
39.7
32.6
64.9
108
141
167
190
206
214
217
217
---
XT
0.607
0.623 0.689 0.733 0.764 0.762 0.723 0.689 0.669 0.683 0.694
Fd
---
0.22
0.27
0.29
0.31
0.31
0.31
0.31
0.31
0.31
0.30
---
Cv
39.8
25.0
47.2
70.1
88.5
101
116
123
127
129
130
0.89
40.8
60.6
76.6
87.4
100
106
110
112
112
---
Flow
Coefficient
Valve OpeningPercent of Total Travel
---
Kv
34.4
21.6
XT
0.841
0.707 0.879 0.948 0.989 0.956 0.875 0.851 0.834 0.840 0.834
Cv
92.0
73.6
150
232
306
353
389
416
441
451
460
0.82
130
201
265
305
336
360
381
390
398
---
---
Kv
79.6
63.7
XT
0.660
0.664 0.651 0.667 0.694 0.722 0.742 0.728 0.723 0.719 0.710
Fd
---
0.17
0.22
0.25
0.26
0.27
0.28
0.28
0.28
0.28
0.28
---
Cv
64.9
52.3
101
150
199
247
284
310
329
345
358
0.87
87.4
130
172
214
246
268
285
298
310
---
Kv
56.1
45.2
XT
0.758
0.774 0.763 0.771 0.778 0.763 0.761 0.717 0.699 0.707 0.691
Cv
108
290
389
480
554
615
658
705
744
0.87
163
251
336
415
479
532
569
610
644
---
Kv
93.4
69.5
0.653
0.670 0.628 0.679 0.731 0.766 0.806 0.829 0.859 0.863 0.866
Cv
108
Kv
93.4
0.653
Fd
---
---
188
XT
XT
---
80.3
---
135
291
434
551
639
706
759
807
841
863
0.85
117
252
375
477
553
611
657
698
727
746
---
0.643 0.699 0.757 0.807 0.838 0.861 0.857 0.841 0.838 0.827
---
0.19
---
0.24
0.26
0.27
0.28
1. When using 655-ET as a control valve for on-off service, the maximum travel for sizing purposes is 19 mm (0.75 inch).
2. When using self-operated regulators, use coefficients listed for 6 mm (0.25 inch) travel.
3. At 100% travel.
4. Restricted trim.
Notes: The coefficients shown on this page are also appropriate
for ETR.
34
FL(3)
0.28
0.28
0.28
0.28
0.27
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 33. Fisher ET, CL125-600, Linear Cage
Linear
Linear
Characteristic
Port
Diameter
Maximum
Travel(2)
Valve
Size,
NPS
mm
Inches
mm
Inches
33.3
1.3125
19
0.75
47.6
1.875
19
0.75
1-1/2
33.3
1.3125
(3)
(3)
58.7
2.3125
19
29
0.75
1.125
2
33.3
1.3125
(3)
(3)
73.0
2.875
19
38
0.75
1.5
2-1/2
47.6
1.875
(3)
(3)
87.3
3.4375
19
38
0.75
1.5
3
58.7
2.3125
(3)
(3)
111.1
4.375
29
51
1.125
4
73.0
2.875
(3)
(3)
38
1.5
Flow
Coefficient
10
20
30
40
50
60
70
80
90
100
Cv
3.21
5.50
8.18
10.9
13.2
15.0
16.9
18.6
19.9
20.6
0.84
Kv
2.78
4.76
7.08
9.43
11.4
13.0
14.6
16.1
17.2
17.8
---
XT
0.340
0.644
0.494
0.509
0.532
0.580
0.610
0.629
0.628
0.636
---
Cv
4.23
7.84
11.8
15.8
20.4
25.3
30.3
34.7
37.2
39.2
0.82
Valve OpeningPercent of Total Travel
FL(1)
Kv
3.66
6.78
10.2
13.7
17.6
21.9
26.2
30.0
32.2
33.9
---
XT
0.656
0.709
0.758
0.799
0.738
0.729
0.708
0.686
0.683
0.656
---
Fd
0.30
0.37
0.41
0.44
0.44
0.41
0.38
0.35
0.34
0.34
---
Cv
2.92
5.70
9.05
12.5
15.6
18.5
21.1
23.9
26.8
29.2
0.91
---
Kv
2.53
4.93
7.83
10.8
13.5
16.0
18.3
20.7
23.2
25.3
XT
0.690
0.651
0.633
0.634
0.650
0.666
0.708
0.718
0.737
0.733
---
Cv
7.87
16.0
24.9
33.4
42.1
51.8
62.0
68.1
70.6
72.9
0.77
Kv
6.81
13.8
21.5
28.9
36.4
44.8
53.6
58.9
61.1
63.1
---
XT
0.641
0.720
0.728
0.767
0.793
0.754
0.683
0.658
0.652
0.638
---
Fd
0.30
0.35
0.36
0.37
0.37
0.36
0.35
0.35
0.34
0.33
---
Cv
3.53
6.36
9.92
13.3
16.5
19.7
22.7
25.6
29.3
33.3
0.87
---
Kv
3.05
5.50
8.58
11.5
14.3
17.0
19.6
22.1
25.3
28.8
XT
0.456
0.529
0.549
0.582
0.611
0.633
0.671
0.723
0.727
0.694
---
Cv
9.34
21.6
35.5
49.5
62.7
74.1
83.6
93.5
102
108
0.81
Kv
8.08
18.7
30.7
42.8
54.2
64.1
72.3
80.9
88.2
93.4
---
XT
0.680
0.660
0.644
0.669
0.674
0.706
0.716
0.687
0.658
0.641
---
Fd
0.27
0.33
0.35
0.36
0.35
0.34
0.32
0.29
0.27
0.27
---
Cv
4.10
8.09
12.3
16.7
21.1
26.8
33.7
41.3
49.2
57.0
0.84
---
Kv
3.55
7.00
10.6
14.4
18.3
23.2
29.2
35.7
42.6
49.3
XT
0.668
0.646
0.684
0.688
0.698
0.694
0.678
0.668
0.669
0.666
---
Cv
14.5
32.9
52.1
70.4
88.5
105
118
133
142
148
0.82
Kv
12.5
28.5
45.1
60.9
76.6
90.8
102
115
123
128
---
XT
0.671
0.699
0.697
0.720
0.733
0.718
0.707
0.650
0.630
0.620
---
Fd
0.26
0.32
0.35
0.36
0.36
0.36
0.36
0.28
0.29
0.30
---
Cv
8.06
16.9
26.7
37.5
49.0
61.4
73.8
85.3
94.7
102
0.85
---
Kv
6.97
14.6
23.1
32.4
42.4
53.1
63.8
73.8
81.9
88.2
XT
0.592
0.614
0.662
0.672
0.674
0.676
0.694
0.722
0.736
0.732
---
Cv
23.3
50.3
78.1
105
127
152
181
203
223
236
0.82
Kv
20.2
43.5
67.6
90.8
110
131
157
176
193
204
---
XT
0.691
0.714
0.720
0.731
0.764
0.757
0.748
0.762
0.732
0.688
---
Fd
0.31
0.36
0.38
0.38
0.37
0.35
0.32
0.30
0.27
0.28
---
Cv
9.77
22.6
37.2
51.8
65.7
77.5
87.5
97.9
107
113
0.84
Kv
8.45
19.5
32.2
44.8
56.8
67.0
75.7
84.7
92.6
97.7
---
XT
0.926
0.899
0.873
0.904
0.919
0.962
0.972
0.937
0.891
0.872
---
-continued-
35
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 33. Fisher ET, CL125-600, Linear Cage (continued)
Valve
Size,
NPS
Port
Diameter
mm
177.8
Inches
Maximum
Travel(2)
mm
51
Inches
8(2)
111.1
4.375
(3)
(3)
203.2
203.2
51
51
76
Flow
Coefficient
10
Cv
Kv
Valve OpeningPercent of Total Travel
FL(1)
20
30
40
50
60
70
80
90
100
46.3
107
171
228
279
327
367
402
420
433
0.84
40.0
92.6
148
197
241
283
317
348
363
375
---
XT
0.656
0.727
0.744
0.781
0.803
0.800
0.784
0.758
0.755
0.740
---
Fd
0.21
0.26
0.29
0.30
0.31
0.31
0.31
0.28
0.28
0.28
---
Cv
16.7
38.6
65.4
93.7
123
156
194
244
290
322
0.88
---
Kv
14.4
33.4
56.6
81.1
106
135
168
211
251
279
XT
0.762
0.698
0.675
0.684
0.681
0.660
0.676
0.657
0.685
0.703
---
Cv
60.2
129
206
285
363
444
526
581
640
688
0.87
---
Kv
52.1
112
178
247
314
384
455
503
554
595
XT
0.704
0.721
0.657
0.651
0.683
0.713
0.740
0.801
0.821
0.839
---
Cv
91.4
207
325
440
550
639
711
760
795
846
0.87
Kv
79.1
179
281
381
476
553
615
657
688
732
---
XT
0.651
0.624
0.677
0.746
0.786
0.803
0.823
0.836
0.843
0.807
---
Fd
0.23
0.28
0.30
0.31
0.31
0.31
0.31
0.31
0.31
0.31
---
1. At 100% travel.
2. If coefficients listed above for the 8-inch linear cage with 51 mm (2-inch) travel are not sufficient for your application, consider using the quick opening cage. The 8-inch quick opening
cage with 51 mm (2-inch) travel has approximately a linear characteristic.
3. Restricted trim.
Notes: The coefficients shown on this page are also appropriate
for ETR.
36
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 34. Fisher ET, CL125-600, Equal Percentage Cage, Flow Down
Equal Percentage
Equal Percentage
Port
Diameter
Characteristic
Maximum
Travel
Valve
Size,
NPS
mm
Inches
mm
Inches
33.3
1.3125
19
0.75
47.6
1.875
19
0.75
1-1/2
33.3
1.3125
(2)
(2)
58.7
2.3125
19
29
0.75
1.125
2
33.3
1.3125
(2)
(2)
73.0
2.875
19
38
0.75
1.5
2-1/2
47.6
1.875
(2)
(2)
87.3
3.4375
19
38
0.75
1.5
3
58.7
2.3125
(2)
(2)
111.1
4.375
29
51
1.125
4
73.0
2.875
(2)
(2)
38
1.5
Flow
Coefficient
10
20
30
40
50
60
70
80
90
100
Cv
0.783
1.54
2.20
2.89
4.21
5.76
7.83
10.9
14.1
17.2
0.88
Kv
0.677
1.33
1.90
2.50
3.64
4.98
6.77
9.43
12.2
14.9
---
XT
0.766
0.614
0.587
0.667
0.672
0.687
0.743
0.760
0.733
0.667
---
Cv
1.52
2.63
3.87
5.41
7.45
11.2
17.4
24.5
30.8
35.8
0.84
Valve OpeningPercent of Total Travel
FL(1)
Kv
1.31
2.27
3.35
4.68
6.44
9.69
15.1
21.2
26.6
31.0
---
XT
0.780
0.735
0.716
0.715
0.738
0.727
0.690
0.685
0.685
0.679
---
Fd
0.64
0.63
0.63
0.64
0.46
0.45
0.30
0.31
0.35
0.38
---
Cv
1.12
1.56
2.22
3.10
4.27
6.17
9.01
13.1
18.2
23.1
0.91
---
Kv
0.969
1.35
1.92
2.68
3.69
5.34
7.79
11.3
15.7
20.0
XT
0.821
0.864
0.820
0.703
0.721
0.679
0.665
0.639
0.650
0.700
---
Cv
1.66
2.93
4.66
6.98
10.8
16.5
25.4
37.3
50.7
59.7
0.85
Kv
1.44
2.53
4.03
6.04
9.34
14.3
22.0
32.3
43.9
51.6
---
XT
0.827
0.834
0.774
0.727
0.687
0.684
0.702
0.736
0.686
0.687
---
Fd
0.41
0.50
0.53
0.58
0.37
0.32
0.27
0.26
0.29
0.31
---
Cv
0.923
1.42
2.09
2.84
4.11
5.83
8.58
12.8
18.5
24.3
0.88
---
Kv
0.798
1.23
1.81
2.46
3.56
5.04
7.42
11.1
16.0
21.0
XT
0.775
0.744
0.742
0.707
0.715
0.714
0.714
0.641
0.621
0.649
---
Cv
3.43
7.13
10.8
15.1
22.4
33.7
49.2
71.1
89.5
99.4
0.84
Kv
2.97
6.17
9.34
13.1
19.4
29.2
42.6
61.5
77.4
86.0
---
XT
0.778
0.702
0.678
0.677
0.658
0.654
0.661
0.665
0.661
0.660
---
Fd
0.45
0.49
0.49
0.47
0.35
0.32
0.30
0.24
0.25
0.27
---
Cv
1.57
2.57
3.82
5.44
7.64
11.5
18.2
26.7
35.1
43.9
0.89
---
Kv
1.36
2.22
3.30
4.71
6.61
9.95
15.7
23.1
30.4
38.0
XT
0.801
0.756
0.713
0.677
0.648
0.672
0.628
0.635
0.706
0.710
---
Cv
4.32
7.53
10.9
17.1
27.2
43.5
66.0
97.0
120
136
0.82
Kv
3.74
6.51
9.43
14.8
23.5
37.6
57.1
83.9
104
118
---
XT
0.774
0.706
0.682
0.635
0.616
0.602
0.663
0.693
0.670
0.675
---
Fd
0.52
0.63
0.68
0.39
0.36
0.29
0.26
0.28
0.30
0.32
---
Cv
1.75
3.11
4.77
7.07
10.7
17.0
27.9
41.5
58.0
70.7
0.87
---
Kv
1.51
2.69
4.13
6.12
9.26
14.7
24.1
35.9
50.2
61.2
XT
0.944
0.840
0.803
0.757
0.735
0.642
0.531
0.613
0.629
0.702
---
Cv
5.85
11.6
18.3
30.2
49.7
79.7
125
171
205
224
0.82
Kv
5.06
10.0
15.8
26.1
43.0
68.9
108
148
177
194
---
XT
0.731
0.650
0.643
0.645
0.632
0.625
0.672
0.742
0.737
0.716
---
Fd
0.45
0.42
0.40
0.33
0.30
0.28
0.23
0.24
0.26
0.28
---
Cv
3.82
7.65
11.4
16.9
25.5
38.2
60.5
85.7
105
112
0.89
Kv
3.30
6.62
9.86
14.6
22.1
33.0
52.3
74.1
90.8
96.9
---
XT
0.746
0.700
0.694
0.669
0.640
0.627
0.591
0.644
0.735
0.813
---
-continued-
37
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 34. Fisher ET, CL125-600, Equal Percentage Cage, Flow Down (continued)
Valve
Size,
NPS
Port
Diameter
mm
177.8
Inches
Maximum
Travel
mm
51
Inches
111.1
4.375
(2)
(2)
203.2
203.2
51
51
76
Flow
Coefficient
10
20
30
40
Cv
12.9
25.8
43.3
Kv
11.2
22.3
37.5
XT
0.688
0.680
Fd
0.39
Cv
5.40
Valve OpeningPercent of Total Travel
60
70
80
90
100
67.4
104
162
239
316
368
394
0.85
58.3
90.0
140
207
273
318
341
---
0.682
0.709
0.700
0.720
0.736
0.744
0.780
0.778
---
0.44
0.47
0.33
0.29
0.22
0.22
0.24
0.25
0.26
---
10.1
15.8
26.7
45.2
71.2
111
169
232
274
0.88
---
Kv
4.67
8.74
13.7
23.1
39.1
61.6
96.0
146
201
237
XT
0.834
0.834
0.735
0.654
0.626
0.613
0.614
0.610
0.629
0.695
---
Cv
18.5
38.0
58.4
86.7
130
189
268
371
476
567
0.85
---
Kv
16.0
32.9
50.5
75.0
112
163
232
321
412
490
XT
0.727
0.623
0.600
0.588
0.580
0.587
0.599
0.611
0.671
0.724
---
Cv
27.0
58.1
105
188
307
478
605
695
761
818
0.86
Kv
23.4
50.3
90.8
163
266
413
523
601
658
708
---
XT
0.644
0.654
0.636
0.611
0.643
0.615
0.725
0.809
0.804
0.807
---
Fd
0.28
0.26
0.23
0.20
0.17
0.22
0.24
0.25
0.25
0.26
---
1. At 100% travel.
2. Restricted trim.
Notes: The coefficients shown on this page are also appropriate
for ETR.
38
FL(1)
50
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 35. Fisher ET, CL125-600, Whisper Trim I Cage, Flow Up
Linear
Characteristic
Whisper Trim I
Valve
Size,
NPS(1)
1
Port
Diameter
mm
33.3
47.6
Inches
1.3125
1.875
Maximum
Travel
mm
19
19
Inches
0.75
0.75
1-1/2
33.3
1.3125
(2)
(2)
58.7
2.3125
19
29
0.75
1.125
2
33.3
1.3125
(2)
(2)
73.0
2.875
19
38
0.75
1.5
2-1/2
47.6
1.875
(2)
(2)
87.3
3.4375
19
38
0.75
1.5
3
58.7
2.3125
(2)
(2)
111.1
4.375
29
51
1.125
73.0
2.875
(2)
(2)
177.8
203.2
38
51
1.5
76
(3,4)
(3,4)
8
29
(5)
(5)
Flow
Coefficient
10
20
30
40
50
60
70
80
90
100
Cv
3.28
7.39
12.0
14.2
14.9
15.3
15.7
16.0
16.4
16.8
Valve OpeningPercent of Total Travel
Kv
2.84
6.39
10.4
12.3
12.9
13.2
13.6
13.8
14.2
14.5
XT
0.581
0.605
0.617
0.644
0.764
0.790
0.809
0.813
0.795
0.768
Cv
2.62
7.42
13.9
20.8
23.2
24.2
24.9
25.4
26.1
26.7
Kv
2.27
6.42
12.0
18.0
20.1
20.9
21.5
22.0
22.6
23.1
XT
0.892
0.766
0.632
0.498
0.614
0.771
0.876
0.919
0.901
0.894
Cv
3.12
7.36
13.0
18.5
20.7
21.4
21.8
23.1
23.9
25.2
Kv
2.70
6.37
11.2
16.0
17.9
18.5
18.9
20.0
20.7
21.8
XT
0.559
0.605
0.460
0.383
0.472
0.622
0.768
0.823
0.874
0.857
Cv
7.30
19.2
34.6
42.2
45.5
47.0
47.1
47.2
47.2
48.0
Kv
6.31
16.6
29.9
36.5
39.4
40.7
40.7
40.8
40.8
41.5
XT
0.604
0.467
0.318
0.387
0.526
0.689
0.843
0.899
0.940
0.938
Cv
2.86
6.79
11.7
18.4
23.6
27.9
30.9
33.5
35.3
36.7
Kv
2.47
5.87
10.1
15.9
20.4
24.1
26.7
29.0
30.5
31.7
XT
0.672
0.755
0.547
0.386
0.358
0.377
0.398
0.431
0.470
0.483
Cv
12.2
32.6
49.7
54.4
55.9
59.8
64.0
67.7
71.4
74.0
Kv
10.6
28.2
43.0
47.1
48.4
51.7
55.4
58.6
61.8
64.0
XT
0.748
0.428
0.414
0.589
0.792
0.877
0.857
0.792
0.712
0.719
Cv
3.11
8.31
14.9
22.4
29.9
36.0
41.6
46.4
50.5
53.6
Kv
2.69
7.19
12.9
19.4
25.9
31.1
36.0
40.1
43.7
46.4
XT
0.603
0.761
0.596
0.467
0.397
0.395
0.398
0.411
0.427
0.439
Cv
16.5
40.3
70.8
88.0
92.1
90.7
90.3
92.6
95.6
99.1
Kv
14.3
34.9
61.2
76.1
79.7
78.5
78.1
80.1
82.7
85.7
XT
0.685
0.471
0.331
0.378
0.532
0.753
0.929
0.983
0.968
0.923
Cv
8.15
19.1
33.2
47.6
60.8
72.1
81.8
90.1
97.4
103
Kv
7.05
16.5
28.7
41.2
52.6
62.4
70.8
77.9
84.3
89.1
XT
0.720
0.660
0.500
0.439
0.406
0.412
0.437
0.472
0.504
0.510
Cv
33.9
76.6
117
135
137
137
141
149
157
169
Kv
29.3
66.3
101
117
119
119
122
129
136
146
XT
0.607
0.385
0.352
0.467
0.682
0.887
0.977
0.958
0.921
0.811
Cv
13.6
32.5
54.3
75.5
94.6
112
127
141
153
160
Kv
11.8
28.1
47.0
65.3
81.8
96.9
110
122
132
138
XT
0.674
0.481
0.374
0.344
0.345
0.354
0.370
0.385
0.407
0.428
Cv
55.8
125
196
245
270
286
297
308
323
338
Kv
48.3
108
170
212
234
247
257
266
279
292
XT
0.294
0.323
0.286
0.322
0.406
0.494
0.579
0.644
0.673
0.662
Cv
100
226
337
436
502
581
641
655
659
681
Kv
86.5
195
292
377
434
503
554
567
570
589
XT
0.456
0.490
0.470
0.427
0.452
0.468
0.521
0.624
0.703
0.701
Cv
142
303
428
542
611
652
669
689
700
726
Kv
123
262
370
469
529
564
579
596
606
628
XT
0.549
0.450
0.436
0.441
0.513
0.624
0.707
0.709
0.729
0.718
1. NPS 6 valve with restricted Whisper Trim not available. Use EW valve where this trim is desired.
2. Restricted trim.
3. Travel limited to 70 mm (2.75 inches) with Class IV ET valve plug.
4. Travel limited to 64 mm (2.5 inches) with anti-extrusion ring or ET-C valve plug.
5. Travel limited to 95 mm (3.75 inches) with anti-extrusion ring or ET-C valve plug.
Notes: The coefficients shown on this page are also appropriate for ETR.
39
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 36. Fisher ET, CL125-600, Whisper Trim III Cage, Flow Up
Linear
Characteristic(2)
Whisper Trim III
Valve
Size,
NPS
Port
Diameter
mm
Inches
Maximum
Travel
mm
Inches
Flow
Coefficient
Minimum(3)
Cv
4.67
68.2
Kv
4.04
59.0
Valve OpeningPercent of Total Travel
20
30
XT(1)
40
50
60
70
80
90
100
92.0
129
163
196
228
257
279
295
0.714
79.6
112
141
170
197
222
241
255
---
A3 DP/P10.6
6
136.5
5.375
76
B3 DP/P10.75
6
136.5
5.375
76
Cv
4.67
38.2
66.9
94.5
120
144
167
190
211
228
0.473
Kv
4.04
33.0
57.9
81.7
104
125
144
164
183
197
---
C3 DP/P10.85
6
136.5
5.375
76
Cv
4.67
28.0
41.3
55.3
69.3
83.0
97.0
110
124
138
0.563
Kv
4.04
24.2
35.7
47.8
59.9
71.8
83.9
95.2
107
119
---
Cv
4.67
6.67
9.50
19.9
31.4
46.0
61.0
75.7
89.7
104
0.563
Kv
4.04
5.77
8.22
17.2
27.2
39.8
52.8
65.5
77.6
90.0
---
D3 DP/P10.99
6
136.5
5.375
76
1. This column lists XT factors for Whisper Trim III cages at 100% travel.
2. Level D exhibits an equal percentage characteristic for the first 38 mm (1.5 inches) of travel, then linear characteristic.
3. This coefficient is minimum rather than 10% open. Valves should not be required to throttle at less than the specified minimum coefficient for an extended periodof time. Erosion
damage to the valve may result.
Notes: The coefficients shown on this page are also appropriate
for ETR.
40
Product Bulletin
51.1:ET
April 2011
ET Valve
Table 37. Fisher ET, Cavitrol III Cage
CL600 - Flow Down
Valve
Size,
NPS
Port
Diameter
mm Inches
Linear
Characteristic
Minimum
Throttling
Cv(1)
Inches
Total Travel
mm
Flow
Coefficient
10
Cv
0.25
Kv
0.216
Cv
0.59
Valve OpeningPercent of Total Travel
20
30
40
50
60
0.48
2.36
5.04
7.36
0.415
2.04
4.36
6.37
0.72
2.54
6.03
9.32
FL(3)
70
80
90
100
9.47
11.2
13.1
14.6
15.5
8.19
9.69
11.3
12.6
13.4
---
12.8
15.6
18.2
20.8
22.5
0.93
One Stage
1
1-1/2
2
2-1/2
3
4
6
8
33.3 1.3125 25.4
47.6
1.875
22.2
58.7 2.3125 28.6
73.0
2.875 38.1(2)
1
0.875
1.125
1.5
87.3 3.4375 41.3(2) 1.625
111.1 4.375 54.0(2) 2.125
177.8
203.2
7
8
57.2
85.7
2.25
3.375
1.9
2.5
3.9
4.2
4.6
5.2
10
15
0.90
Kv
0.510
0.623
2.20
5.22
8.06
11.1
13.5
15.7
18.0
19.5
---
Cv
0.84
1.49
6.68
12.3
17.3
22.1
26.7
30.9
34.4
36.1
0.93
Kv
0.727
1.29
5.78
10.6
15.0
19.1
23.1
26.7
29.8
31.2
---
Cv
0.84
6.83
16.2
25.0
33.0
41.2
48.8
55.5
61.7
64.4
0.91
Kv
0.727
5.91
14.0
21.6
28.5
35.6
42.2
48.0
53.4
55.7
---
Cv
1.65
10.8
22.3
34.3
45.3
55.5
64.7
72.7
80.0
86.7
0.89
Kv
1.43
9.34
19.3
29.7
39.2
48.0
56.0
62.9
69.2
75.0
---
Cv
3.47
22.7
43.3
63.4
81.8
100
116
131
144
151
0.90
Kv
3.00
19.6
37.5
54.8
70.8
86.5
100
113
125
131
---
Cv
4.6
30.0
65.3
99.7
134
165
195
219
241
259
0.91
Kv
4.0
25.9
56.5
86.2
116
143
169
189
208
224
---
Cv
16.2
70.2
124
176
227
276
324
370
412
439
0.94
Kv
14.0
60.7
107
152
196
239
280
320
356
380
--0.98
Two Stage
1
1-1/2
2
2-1/2
3
4
6
8
25.4
33.3 1.3125
47.6
1.875
58.7 2.3125
73.0
73.0
2.875
2.875
136.5 5.375
177.8
25
38
51
64
76
102
102
152
1
1.5
2
2.5
3
4
4
6
0.28
0.44
0.92
1.10
1.20
1.90
3.00
7.00
Cv
0.11
0.41
1.08
1.75
2.43
3.10
3.78
4.45
5.12
5.80
Kv
0.095
0.355
0.934
1.51
2.10
2.68
3.27
3.85
4.43
5.02
---
Cv
0.22
1.20
2.23
3.26
4.29
5.31
6.355
7.37
8.40
9.40
0.98
Kv
0.19
1.04
1.93
2.82
3.71
4.59
5.50
6.38
7.27
8.13
---
Cv
0.80
3.05
5.29
7.56
9.83
12.1
14.3
16.5
18.8
21.0
0.98
Kv
0.692
2.64
4.58
6.54
8.50
10.5
12.4
14.3
16.3
18.2
---
Cv
1.75
5.25
8.71
12.2
15.6
19.1
22.6
26.1
29.6
33.0
0.98
Kv
1.51
4.54
7.53
10.6
13.5
16.5
19.5
22.6
25.6
28.5
---
Cv
3.14
8.23
13.3
18.5
23.5
28.7
33.8
38.9
44.0
49.0
0.98
Kv
2.72
7.12
11.5
16.0
20.3
24.8
29.2
33.6
38.1
42.4
---
Cv
2.83
11.2
19.4
27.4
35.5
43.2
50.5
57.1
63.2
69.0
0.98
Kv
2.45
9.69
16.8
23.7
30.7
37.4
43.7
49.4
54.7
59.7
---
Cv
6.05
22.5
38.0
53.7
69.4
85.2
100
115
130
144
0.98
Kv
5.23
19.5
32.9
46.5
60.0
73.7
86.5
99.5
112
125
---
Cv
19.8
47.5
74.5
101
129
156
184
211
238
265
0.98
229
---
Kv
17.1
41.1
64.4
87.4
112
135
159
183
206
1. Valves should not be required to throttle at a Cv less than the specified minimum Cv for an extended period of time. Erosion damage to the valve seats may result.
2. Less than fully available travel.
3. At 100% travel.
41
Product Bulletin
51.1:ET
April 2011
ET Valve
Specifications
Flange, if used: J Cast iron, J WCC carbon
steel, or J LCC carbon steel, J WC9 chrome
moly steel, J CF8M (cast 316 stainless steel), or
J other materials upon request
Valve Plug, Cage, and Metal Seating Parts:
All Valves Except Those with Cavitrol III or
Whisper Trim III Cages: See table 5.
Valves with Cavitrol III Cages: See table 6.
Valves with Whisper Trim III Cages: See table 8.
Valves with WhisperFlo Cages: See table 7.
Bellows Seal Assembly: J 316L stainless steel
or J N04400
All Other Parts: See table 9
Available Configurations
ET: Single-port, globe-style control valve with
cage guiding, balanced valve plug, and
push-down-to-close valve plug action (figures 1
and 2)
EAT: Angle version of ET control valve, used to
facilitate piping or in applications where a
self-draining valve is desired (figure 3)
ETR: Same as ET control valve except with
push-down-to-open valve plug action (figure 4)
Valve Sizes and End Connection Styles
Flanged raisedface per EN 10921/B and see
table 1
Material Temperature Capabilities(2)
Body/Trim Combinations:.
All Valves Except Those with Cavitrol III or
Whisper Trim III Cages: See figure 12.
Valves with Cavitrol III Cages: See table 6.
Valves with Whisper Trim III Cages: See table 8.
Valves with WhisperFlo Cages: See table 7.
Bolting For NACE MR0175 / ISO 15156 and
MR0103: See table 18.
Bonnets: See table 11.
All Other Parts: See table 9
Maximum Inlet Pressures and Temperatures(1,2)
As listed below, unless limited by maximum
pressure drop or material temperature capabilities
Valves with Cast Iron Bodies.
Flanged: Consistent with CL125B or 250B per
ASME B16.1
Valves with Steel and Stainless Steel Bodies.
Flanged: Consistent with CL150, 300, and 600(3)
per ASME B16.34
Screwed or Welding: Consistent with flanged
CL600 per ASME B16.34
Flow Characteristics
Standard Cages: J Quick-opening, J linear, or
J equal percentage
Whisper Trim, WhisperFlo, and Cavitrol
Cages: Linear
Maximum Pressure Drops(2)
Same as maximum inlet pressure for specific
construction defined above, except where further
limited as follows:
All Valves Except Those with Cavitrol III,
Whisper Trim III, and WhisperFlo Cages: See
figure 12.
Valves with Cavitrol III Cages: See figure 13.
Valves with Whisper Trim III Cages: See figure
14 except where further limited by the following
max 'P/P1 ratios(4) 0.60 for level A3 cage,
0.75 for level B3 cage, 0.85 for level C3 cage, or
0.99 for level D3 cage
Valves for NACE MR0175 / ISO 15156 and
MR0103:
See figure 15.
Shutoff Classifications Per ANSI/FCI 70-2
and IEC 60534-4
Flow Directions
ET.
Standard Cage: Normally down
Whisper Trim and WhisperFlo Cages: Always up
Cavitrol Cage: Always down
EAT.
Standard Cage with Liner for Metal Seat:
Normally down
Standard Cage without Liner: Flow up or down
Whisper Trim and WhisperFlo Cages: Always up
ETR.
Standard Cage: Normally up
Whisper Trim Cage: Always down
Flow Coefficients and Noise Level Prediction
Class IV, V, or VI. See tables 2, 3, or 4
See table 12 and Catalog 12
For Whisper Trim III cage flow coefficients (other
than NPS 6 valves), contact your Emerson
Process Managementt sales office
Construction Materials
Body, Bonnet, and Bonnet Spacer or Bottom
- continued -
42
Product Bulletin
51.1:ET
April 2011
ET Valve
Specifications (continued)
Port Diameters and Maximum Valve Plug Travels
See tables 13 and 15
Yoke Boss and Stem Diameters
See table 14
Typical Bonnet Styles
See table 11
Packing Arrangements
Standard Material: Single PTFE V-ring
Optional Materials: See table 9.
ENVIRO-SEAL Packing Systems: See figures
10 and 11.
ENVIRO-SEAL Packing Systems in vacuum
service: Standard ENVIRO-SEAL packing
systems can be used in vacuum service with
packing rings in standard orientation. Do not
reverse the ENVIRO-SEAL PTFE packing rings.
Also, see Bulletin 59.1:061, ENVIRO-SEAL
Packing Systems for Sliding-Stem Valves
Approximate Weights
NPS 1: 14 kg (30 lb)
NPS 1-1/2: 20 kg (45 lb)
NPS 2: 39 kg (85 lb)
NPS 2-1/2: 45 kg (100 lb)
NPS 3: 57 kg (125 lb)
NPS 4: 77 kg (170 lb)
NPS 6: 159 kg (350 lb)
NPS 8: 408 kg (900 lb)
Additional Options
J Lubricator, J lubricator/isolating valve,
J drilled and tapped connection in extension
bonnet for leak-off service, J body drain plug,
J style 3 fabricated extension bonnet made on
order to a specific length for cryogenic service,
J style NS bonnet for seismic service
requirements, J packings suitable for nuclear
service, J Class V shutoff for ET above 232_C
(450_F) using PEEK anti-extrusion rings
1. EN (or other) ratings and end connections can usually be supplied; consult your Emerson Process Management sales office.
2. The pressure or temperature limits in this bulletin, and any applicable code limitations, should not be exceeded.
3. Certain bonnet bolting material selections may require a CL600 easy-e valve assembly to be derated. Contact your Emerson Process Management sales office for more information.
4. Limitation based on excessive noise increase if max 'P/P1 ratio for a given cage level is exceeded.
43
Product Bulletin
ET Valve
51.1:ET
April 2011
ENVIRO-SEAL Packing System Specifications
Applicable Stem Diameters
J 9.5 mm (3/8 inches), J 12.7 mm (1/2 inches),
J 19.1 mm (3/4 inches), J 25.4 mm (1 inch), and
J 31.8 mm (1-1/4 inches) diameter valve stems
Maximum Pressure/Temperature Limits(1)
To Meet the EPA Fugitive Emission Standard
of 100 PPM(2).
For ENVIRO-SEAL PTFE and ENVIRO-SEAL
Duplex packing systems: full CL300 up to 232_C
(450_F)
For ENVIRO-SEAL Graphite ULF packing: 104
bar (1500 psig) at 316_C (600_F)
Construction Materials
PTFE Packing Systems.
Packing Ring and Lower Wiper: PTFE V-ring(3).
Male and Female Adaptor Rings: Carbon-filled
PTFE V-ring
Graphite ULF Packing Systems: Graphite rings
Duplex Packing Systems:.
Male and Female Adaptor Rings: Carbon-filled
PTFE V-ring
Guide Bushings: Carbon graphite
Packing Rings: Graphite composite
Packing Washer: PTFE
Anti-Extrusion Washer: Filled PTFE (not
required for Graphite ULF or duplex packing)
Lantern Ring: S31600 (316 stainless steel) (not
required for Graphite ULF packing)
Packing Box Flange: S31600
Spring: J 17-7PH stainless steel or J N06600
Packing Follower: S31600 lined with
carbon-filled PTFE
Packing Box Studs: Strain-hardened 316
stainless steel
Packing Box Nuts: 316 stainless steel SA194
Grade 8M
1. Refer to the valve specifications in this bulletin for pressure/temperature limits of valve parts. Do not exceed the pressure/temperature rating of the valve. Do not exceed any applicable code
or standard limitation.
2. The Environmental Protection Agency (EPA) has set a limit of 100 parts per million (ppm) for fugitive emissions from a valve in selected VOC (Volatile Organic Compound) services.
3. In vacuum service, it is not necessary to reverse the ENVIRO-SEAL PTFE packing rings.
Note
Neither Emerson, Emerson Process
Management, nor any of their affiliated
entities assumes responsibility for the
selection, use, or maintenance of any
product. Responsibility for the
selection, use, and maintenance of any
product remains with the purchaser
and end user.
Fisher, Cavitrol, easy-e, ENVIRO-SEAL, Whisper Trim, and WhisperFlo are marks owned by one of the companies in the Emerson Process
Management business division of Emerson Electric Co. Emerson Process Management, Emerson, and the Emerson logo are trademarks and
service marks of Emerson Electric Co. All other marks are the property of their respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they
are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or
applicability. All sales are governed by our terms and conditions, which are available upon request. We reserve the right to modify or improve the
designs or specifications of such products at any time without notice. Neither Emerson, Emerson Process Management, nor any of their affiliated
entities assumes responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use, and maintenance of
any product remains solely with the purchaser and end user.
Emerson Process Management
Marshalltown, Iowa 50158 USA
Sorocaba, 18087 Brazil
Chatham, Kent ME4 4QZ UK
Dubai, United Arab Emirates
Singapore 128461 Singapore
www.Fisher.com
EFisher
44
Controls International LLC 1983, 2011; All Rights Reserved
You might also like
- FANSCRIPT: Acceleracers: Return To Hot Wheels City - Part 1/2No ratings yetFANSCRIPT: Acceleracers: Return To Hot Wheels City - Part 1/249 pages
- Product Bulletin Fisher Et Eat Etr Sliding Stem Control Valves en 122398No ratings yetProduct Bulletin Fisher Et Eat Etr Sliding Stem Control Valves en 12239828 pages
- Fisher ET, EAT, and ETR Sliding - Stem Control Valves: ET Valve Product BulletinNo ratings yetFisher ET, EAT, and ETR Sliding - Stem Control Valves: ET Valve Product Bulletin28 pages
- Product Bulletin Fisher Et Eat Etr Sliding Stem Control Valves en 122398No ratings yetProduct Bulletin Fisher Et Eat Etr Sliding Stem Control Valves en 12239828 pages
- Design ET, EAT, and ETR Sliding-Stem Control ValvesNo ratings yetDesign ET, EAT, and ETR Sliding-Stem Control Valves28 pages
- Fisher EW Series (EWD - EWS - EWT) Sliding-Stem Control Valves Through NPS 12x8No ratings yetFisher EW Series (EWD - EWS - EWT) Sliding-Stem Control Valves Through NPS 12x8229 pages
- Fisher Easy e ED Universal Globe Valve Sliding Stem Valves Data SheetNo ratings yetFisher Easy e ED Universal Globe Valve Sliding Stem Valves Data Sheet24 pages
- Fisherr ES and EAS Sliding-Stem Control Valves: ES Valve Product BulletinNo ratings yetFisherr ES and EAS Sliding-Stem Control Valves: ES Valve Product Bulletin20 pages
- PCC Technova: Series "CPL" Cylindrical ValvesNo ratings yetPCC Technova: Series "CPL" Cylindrical Valves5 pages
- Fisher ET and EAT Easy-E Valves CL125 Through CL600 PDFNo ratings yetFisher ET and EAT Easy-E Valves CL125 Through CL600 PDF48 pages
- KLINGER Ballostar KHA 3 Pieces Ball Valve DN 10 - 150: Edition 2011No ratings yetKLINGER Ballostar KHA 3 Pieces Ball Valve DN 10 - 150: Edition 201136 pages
- Product Bulletin Fisher Es Eas Sliding Stem Control Valves en 122406No ratings yetProduct Bulletin Fisher Es Eas Sliding Stem Control Valves en 12240624 pages
- Type 8532 High-Performance Butterfly Valve: Bulletin 51.6:8532No ratings yetType 8532 High-Performance Butterfly Valve: Bulletin 51.6:853212 pages
- Check-Trol: Isolation Flow Control FlangeNo ratings yetCheck-Trol: Isolation Flow Control Flange2 pages
- Flanged Safety Relief Valves - Spring Loaded: Type 447 PTFE-lined Packed Lever H4 Closed Bonnet Bellows DesignNo ratings yetFlanged Safety Relief Valves - Spring Loaded: Type 447 PTFE-lined Packed Lever H4 Closed Bonnet Bellows Design9 pages
- 3 Piece Tube Bore Ball Valves, / "-4": High Purity ApplicationsNo ratings yet3 Piece Tube Bore Ball Valves, / "-4": High Purity Applications4 pages
- Contemporary Anaesthetic Equipments.: An Aid for Healthcare Professionals.From EverandContemporary Anaesthetic Equipments.: An Aid for Healthcare Professionals.No ratings yet
- Gasturbine sgt5 8000h H Klasse Performance PDFNo ratings yetGasturbine sgt5 8000h H Klasse Performance PDF10 pages
- Thermal Efficiency of Combined Cycle Power Plant: June 2018No ratings yetThermal Efficiency of Combined Cycle Power Plant: June 20187 pages
- Performance Evaluation of Combined Heat and Power PDFNo ratings yetPerformance Evaluation of Combined Heat and Power PDF9 pages
- Analysis On Closed-Loop Control System of Class F Gas TurbineNo ratings yetAnalysis On Closed-Loop Control System of Class F Gas Turbine7 pages
- Assignment 4 - Simultaneous Equations - SolutionNo ratings yetAssignment 4 - Simultaneous Equations - Solution2 pages
- MC44 - Inventory Turnover (1) - SAP Mental NotesNo ratings yetMC44 - Inventory Turnover (1) - SAP Mental Notes6 pages
- Owners Manual Comp Shock KTM 125 390 RC DukeNo ratings yetOwners Manual Comp Shock KTM 125 390 RC Duke8 pages
- 12 Metzger, Clinical Pathology Interpretation in Geriatric Veterinary Patients 2012No ratings yet12 Metzger, Clinical Pathology Interpretation in Geriatric Veterinary Patients 201215 pages
- Enable Tax To Calculate On Invoices Originating in Oracle R12 ProjectsNo ratings yetEnable Tax To Calculate On Invoices Originating in Oracle R12 Projects23 pages
- Laser Acupuncture and Auriculotherapy in Postu - 2011 - Journal of Acupuncture ANo ratings yetLaser Acupuncture and Auriculotherapy in Postu - 2011 - Journal of Acupuncture A6 pages
- Evergreen Workbook Answers of With The Photographer Treasure Chest A Collection of Short Stories - Shout To Learn - The Ori100% (1)Evergreen Workbook Answers of With The Photographer Treasure Chest A Collection of Short Stories - Shout To Learn - The Ori1 page
- Strata Control - Metalliferous - October 2023No ratings yetStrata Control - Metalliferous - October 20238 pages
- 3 - SPE-20720-MS - Inflow Performance Relationships For Solution-Gas-Drive PDFNo ratings yet3 - SPE-20720-MS - Inflow Performance Relationships For Solution-Gas-Drive PDF8 pages
- Regency Tables Sinks 600s32424xc Specsheet 2No ratings yetRegency Tables Sinks 600s32424xc Specsheet 22 pages
- 2A5 Linear Programming - Simplex Method - Maximization CaseNo ratings yet2A5 Linear Programming - Simplex Method - Maximization Case16 pages
- The Indian Community School Kuwait First Mid Term Examination - 2022 - 2023 Class - Xi - Mathematics - Answer KeyNo ratings yetThe Indian Community School Kuwait First Mid Term Examination - 2022 - 2023 Class - Xi - Mathematics - Answer Key1 page
- OD5432 Snowplow Manufacturing Industry ReportNo ratings yetOD5432 Snowplow Manufacturing Industry Report32 pages
- PCB-Based Capacitive Touch Sensing With MSP430No ratings yetPCB-Based Capacitive Touch Sensing With MSP43025 pages
- Improved Cryptanalysis of The Block Cipher KASUMINo ratings yetImproved Cryptanalysis of The Block Cipher KASUMI2 pages
- Unitronics Software VisiLogic HMI DisplaysNo ratings yetUnitronics Software VisiLogic HMI Displays101 pages
