Scribd
Upload
229 views13 pages

How To Export Gerber Files From Altium

The document provides instructions for exporting Gerber files from Altium Designer 6 to match the PCB production requirements of Olimex. It details setting minimum clearance, routing width, plane connect, and plane clearance values to 8-10 mills in the design rules. It also recommends using hatched copper pours instead of solid areas. After completing the design and running a design rule check, the instructions describe exporting Gerber files for layers and drill drawings with the correct settings and precision in the fabrication outputs menu.

Uploaded by

Fernando Magalhães Araujo
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
229 views13 pages

How To Export Gerber Files From Altium

The document provides instructions for exporting Gerber files from Altium Designer 6 to match the PCB production requirements of Olimex. It details setting minimum clearance, routing width, plane connect, and plane clearance values to 8-10 mills in the design rules. It also recommends using hatched copper pours instead of solid areas. After completing the design and running a design rule check, the instructions describe exporting Gerber files for layers and drill drawings with the correct settings and precision in the fabrication outputs menu.

Uploaded by

Fernando Magalhães Araujo
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 13

How to export Gerber files from Altium Designer 6 ( Protel) matching Olimex PCB production

Design Setup from Altium

1. Clearance Setup
Before routing and placing anything be sure to setup clearance to minimum 10mill (Olimex can handle a minimum of 8mill but I had problems even though a setting of 10 mill has solving the problems.) This setting can be set in the menu: Design |Rules

Change this to 10mill as shown by the blue arrow

Version 1.0 Olimex 2007

2. Routing Width
Be sure to use minimum 8 mill setting for the Routing Width. This can also be changed in the menu: Design |Rules

3. Plane Connect
Go to menu: Design |Rules and choose the setting for Plane | PlaneConnect Also here be sure to use minimum 8 mill.

Version 1.0 Olimex 2007

4. Plane Clearance
Go to menu: Design |Rules and choose the setting for Plane | PlaneCleance Also here be sure to use minimum 8 mill.

5. Using Polygon Pour


When using a copper surface (Polygon Pours) also remember to use minimum of 8 mills here

NOTE !

The pour needs to be Hatched (made by Tracks and Arcs) instead of a solid copper area.

Remember to set Track Width, Grid Size, Minimum Primitive Length also to minimum 8 mill. A setting of 10 mill works every time !

Version 1.0 Olimex 2007

6. Design Rule Check


After finishing the design and before generating the Gerber files you should run a Design Rule check. This check will use the setting and distances that you have already set up in the previous items following this tutorial.

Go to the menu: Tools | Design Rule Check.

Run the check and go no further with gerber files if errors are found. Read the errors if any correct them until no further errors are found.

Version 1.0 Olimex 2007

7. Gerber Export
To make the Gerber files to the menu: Files | Fabrication Outputs and choose Gerber Files

You will now see 5 pages in the following dialog box

Version 1.0 Olimex 2007

General Setting
In the General Setting set the precision to 2:4 (0,1 mill resolution)

Version 1.0 Olimex 2007

Layers Setting
Include the layers that you want to export by marking these

Drill Drawing Setting


Mark both layers for Drill Drawing Plots

Version 1.0 Olimex 2007

Aperture Setting
Be sure to mark Embedded apertures (RS274X)

Advanced Setting
Be sure to set the Leading/Trailing Zeroes to: Keep leading and trailing zeroes and the Position on Film to: Reference to absolute origin

Version 1.0 Olimex 2007

Now press the button OK to go further on.

8. CAMtasticx.Cam file
A new page called CAMtasticx.Cam will now arrive showing your PCB.

Version 1.0 Olimex 2007

Go selecting menu: File | Export | Gerber

In the dialog box be sure to set these settings

Version 1.0 Olimex 2007

Finally Press OK and you can select where to put your gerber files for each layer.

9. Now exporing exporting your drill settings


Go back to your design PcbDoc file by pressing the Design page in top of your window

Go to the menu: File | Fabrication Outputs and choose NC Drill Files!

Version 1.0 Olimex 2007

Setup the following showed by the blue arrows

Press OK and the following dialog box will be shown

Again press the button OK And another CAM page with all your drillings will be shown. From within this new page Go to the menu: File | Export and choose Gerber Version 1.0 Olimex 2007

Now we are near the end A new dialog box will be shown:

Check that this has been selected. Finally press OK save this gerber file and your are ready to email them to Olimex

Version 1.0 Olimex 2007

You might also like