Scribd
Upload
206 views

GPS Quick Installation Guide - 080710

This document provides installation instructions for an Accutime GPS module. It outlines the necessary equipment, describes how to physically install the GPS outdoor unit and antenna, and connect the indoor and outdoor units with cable. Key steps include mounting the antenna and surge protector bracket, connecting cables between antenna and indoor unit, grounding cables, and crimping the indoor cable connector.

Uploaded by

Agoes Azza
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
206 views

GPS Quick Installation Guide - 080710

This document provides installation instructions for an Accutime GPS module. It outlines the necessary equipment, describes how to physically install the GPS outdoor unit and antenna, and connect the indoor and outdoor units with cable. Key steps include mounting the antenna and surge protector bracket, connecting cables between antenna and indoor unit, grounding cables, and crimping the indoor cable connector.

Uploaded by

Agoes Azza
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Accutime GPS Module Quick Installation Guide

This Quick Installation Guide is intended for experienced installers. For more information refer to the relevant sections in the System Manual and the Base Transceiver Station Installation and Manual.

Preliminaries
Check that you have the following items available (all items should be ordered separately): GPS Adapter cable GPS ODU (GPS-OGR, Outdoor unit) Cable (IDU-ODU) - available in two lengths: 50m, 100m

GPS ODU Package Content


GPS ODU+antenna Pole mounting kit (including plastic pipe, bracket, 2 clamps, 4 M8 nuts, washers and spring washers, 1 x 1032 screw, washer and spring washer). Ant. GPS Surge Protection - (including 3 x 1032 screws, washers and spring washers) This installation guide

IDU-ODU Cable Package Content


Shielded Cat.5E Ethernet cable (crimped on one side only - 12-pin waterproof round female). This is a proprietary cable and must be ordered from the equipment supplier. 2 shielded RJ-45 connectors 1 RJ-45 plastic cover

Additional Equipment and Tools required for Installation


A grounding cable with appropriate terminations for connecting the indoor unit's ground terminal to the rack or to a ground connection. Installation tools WARNING: ONLY experienced installation professionals who are familiar with local building and safety codes and, wherever applicable, are licensed by the appropriate government regulatory authorities should install outdoor units and antennas. Failure to do so may void the product warranty and may expose the end user or Service Provider to legal and financial liabilities. The manufacturer and its resellers or distributors are not liable for injury, damage or regulation violations associated with the installation of outdoor units or antennas.

ODU Installation
GPS Antenna

Pipe

Bracket

Connector

Surge Protection cable 3. Figure 3 Use the supplied screws, washers and spring washers (2 x 1032) to assemble the surge protection cable onto the bracket (see Figure 3). Apply torque 2.1[N*m] (19.2 [lbs*in])

1.

Figure 1 Place the bracket on a flat surface and thread the supplied pipe through the bracket hole and into the GPS antenna (see Figure 1). Hand-tighten until snug. Do not over-tighten or use a tool.

2.

Figure 2 Make sure the connector (male) is on the open side of the bracket (see Figure 2).

-1P/N: 215041 July 2008

Accutime GPS Module Quick Installation Guide

4.

Figure 4 Use a 1032 screw, washer and spring washer to attach the surge protectors grounding cable to the bracket (see Figure 4). Apply torque 2.1[N*m] (19.2 [lbs*in]). Make sure that the female connector faces the antenna.

5.

Figure 5 Connect the surge protector cable (female connector) to the GPS antenna connector (male). Use the groove on the cable connector (indicated by an arrow) as a guide. It aligns with the tenon in the connector on the GPS side. Turn the locking ring on the cable connector clockwise to secure the connection. Do not over-tighten.

6.

Figure 6 Use the supplied clamps to assemble the GPS and bracket on a pole. Use the M8 nuts, washers and spring washers to lock the clamps to the bracket. Apply torque 9 [N*m] (80 [lbs*in]).

7.

8.

Figure 7 Connect the IDU-ODU cable. Use the groove on the cable connector (indicated by an arrow) as a guide. It aligns with the tenon in the connector on the surge protector side. Turn the locking ring on the cable connector clockwise to secure the connection. Do not overtighten. The bracket must be grounded. Use an appropriate grounding cable. You can use the same screw used for grounding the surge protector (in step 4 above).

Figure 8 Fix the cable onto the pole using a cable strip. 10. Route the cable to the location selected for the indoor equipment. Note: Follow the instructions detailed in the Preparing the Indoor-to-Outdoor GPS Cable (supplied with the Cat 5E GPS cable) to crimp the other side of the IDU-ODU cable. 9.

Figure 9 11. Connect the RJ-45 connector from the GPS cable to the RJ-45 jack of the adapter cable. 12. Connect the other end of the data cable (15-pin micro D-Type plug) to the GPS/SYNC IN connector located on the NPU panel. Tighten the two screws until the cable is held firmly.

-2P/N: 215041 July 2008

Accutime GPS Module Quick Installation Guide


Preparing the IDU-ODU Cable
Use a crimp tool for RJ-45 connectors to prepare the wires. Insert them into the appropriate pins and use the tool to crimp the connector. Make sure to do the following: Remove as small a length as possible of the external jacket. Verify that the external jacket is well inside the sealing cover when connected to the unit, to ensure good sealing. Pull back the shield drain wire before inserting the cable into the RJ-45 connector, to ensure a good connection with the connector's shield after crimping. For detailed instructions, refer to the Preparing the Indoor-to-Outdoor GPS Cable instructions, supplied with the Cat 5E GPS cable. The following diagram shows the required wire pair pin-to-pin connections, including the color codes used in cables supplied by the manufacturer.

Wire color Orange/white Orange Brown/white Brown Blue Blue/white Green Green/white

Pin 1 2 3 4 5 6 7 8

-3P/N: 215041 July 2008

You might also like