Scribd
Upload
72 views

Automatic Light Controller

This document describes an automatic light controller circuit that uses a 7806 voltage regulator. The circuit utilizes the characteristic of the voltage regulator that the output voltage increases as the common terminal voltage increases. A transistor is used as a switch to control the connection of the common terminal to ground. A light dependent resistor (LDR) is connected to the transistor so that it acts as a switch based on the ambient light level, turning the light on at night and off during the day. The circuit provides automatic control of a light bulb based on the amount of light falling on the LDR.

Uploaded by

chakralabs
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
72 views

Automatic Light Controller

This document describes an automatic light controller circuit that uses a 7806 voltage regulator. The circuit utilizes the characteristic of the voltage regulator that the output voltage increases as the common terminal voltage increases. A transistor is used as a switch to control the connection of the common terminal to ground. A light dependent resistor (LDR) is connected to the transistor so that it acts as a switch based on the ambient light level, turning the light on at night and off during the day. The circuit provides automatic control of a light bulb based on the amount of light falling on the LDR.

Uploaded by

chakralabs
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

circuit

ideas
92 Apri l 2010 electroni cs for you www. e f y mA g . c o m
M.K. Chandra Mouleeswaran
autoMatiC light Controller
using 7806
S.C. DW
IVEDI
V
oltage regulator ICs (78xx se-
ries) provide a steady output
voltage, as against a widely
fuctuating input supply, when the
common terminal is grounded. Any
voltage about zero volt (ground) con-
nected in the common terminal is add-
ed to the output voltage. That means
the increase in the common terminal
voltage is refected at the output. On
the other hand, if the common terminal
is disconnected from the ground, the
full input voltage is available at the
output.
This characteristic is utilised in the
present circuit. When the common
terminal is connected to the ground,
the regulator output is equivalent to
the rated voltage, and as soon as the
terminal is disconnected from the
ground, the output increases up to the
input voltage.
The common terminal is control-
led by a transistor, which works as a
switch on the terminal. For automatic
control of light, a light-dependent re-
sistor (LDR1) is connected to the base
of the transistor. In this way, the volt-
age regulator is able to operate a light
bulb automatically as per the ambient
light.
To derive the power supply for
the circuit, the 50Hz, 230V AC mains
is stepped down by transformer X1
to deliver a secondary output of 12V,
250 mA. The secondary output of the
transformer is applied to a bridge rec-
tifer comprising diodes D1 through
D4, fltered by capacitor C1 and fed
to the input terminal of the regulator
(IC1).
The common terminal (pin 2) of IC1
is connected to the ground line of the
circuit through transistor BC557 (T1).
The transistor is biased by R2, R3, VR1
and LDR1. The grounding of IC1 is
controlled by transistor T1, while light
is sensed by LDR1. Using preset VR1,
you can adjust the light-sensing level
of transistor T1.
The output of IC1 is fed to the base
of transistor T2 (through resistor R4
and zener diode ZD1) and relay RL1.
LED1 connected across the positive
and ground supply lines acts as a
power-on indicator.
Normally, the resistance of LDR1
is low during daytime and high dur-
ing nighttime. During daytime, when
light falls on LDR1, pnp transistor T1
conducts. The common terminal of IC1
connects to the ground and IC1 outputs
6V. As a result, transistor T2 does not
conduct and the relay remains de-en-
ergised. The light bulb remains off as
the mains connection is not completed
through the relay contacts.
During nighttime, when no light
falls on LDR1, it offers a high resist-
ance at the base junction of transistor
T1. So the bias is greatly reduced and
T1 doesnt conduct. Effectively, this
removes the common terminal of IC1
from ground and it directs the full
input DC to the output. Transistor T2
conducts and the relay energises to
light up the bulb as mains connection
completes through the relay contacts.
As LDR1 is in parallel to VR1+R3
combination, it effectively applies
only half of the total resistance of
the network formed by R3, VR1 and
LDR1 to the junction at T1 in total
darkness. In bright light, it greatly
reduces the total effective resistance
at the junction.
The ci rcui t i s
simple and can be
assembled on a small
gener al - pur pos e
PCB. Use a heat-sink
for IC1. Make sure
that LDR1 and the
light bulb are well
separated.
The circuit can be
used for streetlights,
tubelights or any
other home electri-
cal lighting system
that needs to be au-
tomated.
Visit www.deekshith.in for more unique project ideas and circuits
http://www.deekshith.in/search/label/Projects :Visit for more unique project ideas and circuits
Get this
project done!
Get the Document + PPT + KIT
Are you interested in doing this project either as
your college (mini / major) project or as your
hobby? We can help you out. We can provide you
with all the documents including documentation,
PPT, etc that you need as a student to present
this project at your college.
Also, if you are in need of the hardware kit for
this project, we can provide it to you at a cheaper
cost and in little time.
Contact: http://deekshith.in/p/contact.html
Email: [email protected]
Facebook: http://facebook.com/deekshithallamaneni
Phone: +919441921293 (Local to Hyderabad, India)

Visit www.deekshith.in for more unique project ideas and circuits
http://www.deekshith.in/search/label/Projects :Visit for more unique project ideas and circuits

You might also like