Scribd
Upload
242 views

Plate

This document provides information and calculations for circular, annular, and rectangular plates under various loading conditions. It includes material properties, plate dimensions, load values, and results of the plate stress and deflection calculations. The maximum stresses, deflections, and minimum safety factors are reported for each plate configuration.

Uploaded by

Adnan Rana
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
242 views

Plate

This document provides information and calculations for circular, annular, and rectangular plates under various loading conditions. It includes material properties, plate dimensions, load values, and results of the plate stress and deflection calculations. The maximum stresses, deflections, and minimum safety factors are reported for each plate configuration.

Uploaded by

Adnan Rana
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Plates i ii ? 1.

0 Selection of material and units setting


Imperial (lbf, in, HP.) Structural steel EC 3, EN 10025; Fe 360 / Sy=34100 psi

Calculation without errors. Informace o projektu Project information Input section

1.1 Calculation units 1.2 Material 1.3 Modulus of elasticity 1.4 Modulus of shearing 1.5 Poissons ratio 1.6 Temperature coefficient of expansion 1.7 Specific mass 1.8 Yield strength 1.9 Requested safety coefficient 2.0 Circular plates E G Ro

30457770 11714527 0.30 6.50 490.06 34083.70 3.00

[psi] [psi] [in/in/F*e-6] [lb/feet^3] [psi]

y
SF

2.1 Loading and mounting type 2.2 Plate thickness 2.3 Outer radius 2.4 Radial location of loading 2.5 Total applied force 2.6 Load per unit area 2.7 Uniform temperature differential 2.8 Plate weight

01. Force load on circle, outer edge simply supported

t a ro W
Force

0.200 20.000 5.000 100.00 224.80943 20.000 71.28 -0.07869 2542.87 13.40 0.000 -0.07869 0.0000 16.95 16.95 0.00 2542.87 2542.87 13.40 ya=0; Mra=0

[in] [in] [in] [lbf] [lbf] [F] [lb] [in] [psi]


Deflection

Q dT m yc (ymax)

2.9 Run values calculation (graph) 2.10 Maximum deflection 2.11 Maximum stress 2.12 Minimum safety coefficient 2.13 Values in point 2.14 Deflection 2.15 Radial slope of plate 2.16 Radial bending moment 2.17 Tangential bending moment 2.18 Shear force 2.19 Radial bending stress 2.20 Tangential bending stress 2.21 Safety coefficient 2.22 Boundary values

max
SFmin r [in] y

<0...20> [in] [deg] [lbf*in/in] [lbf*in/in] [lbf/in] [psi] [psi] 0 -0.02 0 -0.04 -0.06 -0.08 -0.1 y [in] x [in] 5 10 15 20 25

Mr Mt Q

r t
SF

3.0

Annular circular plates

3.1 Loading and mounting type 3.2 Plate thickness 3.3 Outer radius 3.4 Inner radius for annular plate 3.5 Radial location of loading 3.6 Total applied force 3.7 Load per unit area 3.8 Uniform temperature differential 3.9 Plate weight

01. Force load on circle, outer edge simply supported, inner edge free

t a b ro W
Pressure

0.200 10.000 6.000 7.000 100.00 10.00000 20.000 11.40 -0.01783 2395.45 14.23 6.000 -0.01783 0.2704 0.00 15.97 0.00 0.00 2395.45 14.23

[in] [in] [in] [in] [lbf] [lb/in^2] [F] [lb] [in] [psi]
Deflection

q dT m ymax

3.10 Run values calculation (graph) 3.11 Maximum deflection 3.12 Maximum stress 3.13 Minimum safety coefficient 3.14 Values in point 3.15 Deflection 3.16 Radial slope of plate 3.17 Radial bending moment 3.18 Tangential bending moment 3.19 Shear force 3.20 Radial bending stress 3.21 Tangential bending stress 3.22 Safety coefficient 3.23 Boundary values 4.0 Rectangular plates
01. Uniform pressure q over entire plate, all edges simply supported

max
SFmin r [in] y

<6...10> [in] [deg] [lbf*in/in] [lbf/in] [psi] [psi] -0.02 y [in] x [in] 0 0 2 4 6 8 10 12

Mr Mt Q

[lbf*in/in] -0.005 -0.01 -0.015

r t
SF

Mrb = 0; Qb = 0; ya = 0; Mra = 0

4.1 Loading and mounting type 4.2 Plate thickness 4.3 Long edge 4.4 Short edge 4.5 Radial location of loading 4.6 Total applied force 4.7 Load per unit area 4.8 Plate weight 4.9 Maximum deflection 4.10 Maximum stress 4.11 Safety coefficient

t a b ro W
Pressure

0.200 10.000 10.000 2.000 100.00 10.00000 5.67 -0.01822 7185.00 4.74

[in] [in] [in] [in] [lbf] [lb/in^2] [lb] [in] [psi]

q m ymax

max
SF

5.0

Circular plates producing large deflection


01. Uniform pressure q over entire plate, fixed and held

5.1 Loading and mounting type 5.2 Plate thickness 5.3 Outer radius 5.4 Total applied force 5.5 Load per unit area 5.6 Plate weight 5.7 Maximum deflection 5.8 Stress in the plate centre 5.9 Stress in the plate boundary 5.10 Stress in the plate boundary 5.11 Minimum safety coefficient 6.0 6.1 Mounting and loading type 6.2 Plate thickness 6.3 Long edge 6.4 Short edge 6.5 Load per unit area 6.6 Plate weight 6.7 Maximum deflection 6.8 Diaphragm stress

t a W
Pressure

0.200 20.000 224.809 1.00000 71.28 -0.09934 5060.40 7014.53 2104.51 4.86

[in] [in] [lbf] [lb/in^2] [lb] [in] [psi] [psi] [psi] Move values from pragraph [2.0]

q m ymax

(c) (r) (t)


SFmin

Rectangular plates producing large deflection


01. Held, not fixed, at center of plate (a/b = 1), (Uniform pressure q over entire plate)

t a b
Pressure

0.200 10.000 10.000 10.00000 5.67 -0.01412 1400.00 7600.00 4.48

[in] [in] [in] [lb/in^2] [lb] [in] [psi] [psi] Move values from paragraph [4.0]

q m ymax

6.9 Bending + diaphragm stress (sum) 6.10 Safety coefficient

d sum
SF

You might also like