Scribd
Upload
930 views

Automatic Street Light Controller

This document describes a dark sensitive automatic street light system that uses a light dependent resistor (LDR) sensor to automatically turn street lights on and off. The system detects darkness levels and uses a transistor switch to power the lights. When darkness rises above a certain threshold set by a potentiometer, the lights turn on, and when sunlight is detected again, the lights turn off. This automatic control can reduce energy costs compared to manual operation and timer-based systems.

Uploaded by

Asif Newaz Khan
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
930 views

Automatic Street Light Controller

This document describes a dark sensitive automatic street light system that uses a light dependent resistor (LDR) sensor to automatically turn street lights on and off. The system detects darkness levels and uses a transistor switch to power the lights. When darkness rises above a certain threshold set by a potentiometer, the lights turn on, and when sunlight is detected again, the lights turn off. This automatic control can reduce energy costs compared to manual operation and timer-based systems.

Uploaded by

Asif Newaz Khan
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 16

Dark Sensitive Automatic Street Light

1. Introduction

Automatic Street Light Control System is a simple and powerful concept, which uses transistor as a switch to switch ON and OFF the street light automatically. By using this system manual works are removed. It automatically switches ON lights when the sunlight goes below the visible region of our eyes. It automatically switches OFF lights under illumination by sunlight. This is done by a sensor called Light Dependant Resistor (LDR) which senses the light actually like our eyes. By using this system energy consumption is also reduced because now-adays the manually operated street lights are not switched off properly even the sunlight comes and also not switched on earlier before sunset. In sunny and rainy
2

days, ON time and OFF time differ significantly which is one of the major disadvantage of using timer circuits or manual operation. This project exploits the working of a transistor in saturation region and cut-off region to switch ON and switch OFF the lights at appropriate time with the help of an electromagnetically operated switch. Automatic Streetlight needs no manual operation of switching ON and OFF. The system itself detects whether there is need for light or not. When darkness rises to a certain value then automatically streetlight is switched ON and when there is other source of light, the street light gets OFF. The extent of darkness at which the street light to be switched on can also be tailored using the potentiometer provided in the circuit.

2. Principle

The automatic streetlight control system operates on 12 V DC supply. The automatic streetlight controller has a photoconductive device whose resistance changes proportional to the extent of illumination, which switches ON or OFF the LED with the use of transistor as a switch . Light dependent resistor, a photoconductive device has been used as the transducer to convert light energy into electrical energy. The central dogma of the circuit is that the change in voltage drop across the light dependent resistor on
4

illumination or darkness switches the transistor between cut-off region or saturation region and switches OFF or ON the LED.

3. Circuit Diagram

Circuit Diagram
The circuit diagram of automatic street light controller is given below:

4. Component

> 9v Battery with strip > Switch > L.D.R (Light Depending Resistance) > I.C NE555 with Base

> L.E.D (Light Emitting Diode) 3 to 6 pieces. > Variable Resistance of 47 Kilo ohms > P.C.B (Printed Circuit Board of 555)

7. Uses of this project

By employing this circuit, energy consumption can be reduced considerably as the light switches ON or OFF automatically in appropriate time. Moreover, errors which occur due to manual operation also can be eliminated
10

completely. The Automatic street light controller unit fabrication is cost-effective with good sensitivity and high reproducibility. Moreover, the construction of the circuit is also simple so that it can be done easily as it involves locally available components. The circuit is designed in such a way that the extent of darkness at which the light has to switch ON or OFF also can be tailored whenever it is needed. It can be used for other purposes like garden lighting, balcony lighting etc.,

11

8. Conclusion & Scope

12

Application 1:
The above circuit can be powered from a battery, which can be charged during day time by harvesting the solar energy through a solar cell as shown below:

Solar cell

Battery

Application 2:

13

The solar energy harvested from sunlight can be stored, inverted from DC voltage to AC voltage using sun tie converter. The AC voltage can be stepped up and given to the electric grid.

Photovoltaic array

The AC voltage from the electric grid can be stepped down, rectified and used for powering the circuit. Meanwhile, the street light can also be powered by the A.C. voltage, which is controlled by a relay switch connected to the switching part of
14

the circuit. The above mentioned strategy will enable us to harvest solar energy in an effective way for the operation of the circuit and for powering the street light also.

Solar Street light system with Automatic street light controller A Future perspective

15

16

You might also like