Users Guide

Release 8.2

a u t o s h i p
Systems Corporation

Suite 312 611 Alexander Street Vancouver B C V6A 1E1 Canada

Tel (604) 254-4171 Fax (604) 254-5171 Internet www.autoship.com

Copyright 2003 Autoship Systems Corporation Windows is a trademark of Microsoft Corporation AutoCAD is a trademark of Autodesk, Inc.

Information contained in this document is subject to change without further notice. No part of this document may be reproduced or transmitted in any form, or by any means, electronic of mechanical, for any purpose, without the express permission of Autoship Systems Corporation. 2003 Autoship Systems Corporation. All right reserved. Windows is a trademark of Microsoft Corporation. AutoCAD is a trademark of Autodesk Inc. All other product names are trademarks, registered trademarks, or service marks of their respective owners. Autoship Systems Corporation cannot attest to the accuracy of this information. In addition, terms suspected of being trademarks, registered trademarks, or service marks have been appropriately capitalized. Use of a term in this book should not be regarded as a validity of any trademark, registered trademarks, or service mark. Autoship Systems Corporation Suite 312 611 Alexander Street Vancouver, B.C. V6A 1E1 Canada Tel: (604) 254-4171 Fax: (604) 254-5171 Internet: www.autoship.com

Table of Contents
Introduction
Introduction to Autoship 8.2 Whats New Contact Information 1 3 7

Installation Instructions
System Requirements Installation Instructions Hardware Locks 9 10 11

Getting Started
Starting and Exiting Autoship References and Help Resources Updating Autoship 15 15 19

Table of Contents

Tutorials
Introduction: Tutorial 1 Chine Hull Planing Boat:
Introduction to Autoships tools for constructing a model. How to use Autoships basic building blocks objects in creating and using simple curves and surfaces. How to create a hull using developable and ruled surfaces. How to create and fit a cylindrical transom. Attaching curve ends to points. Tangency at the end of curves. How to obtain offsets and hydrostatics.

21 23

Tutorial 2 Round Bilge Hull:

Continued introduction to Autoships tools for creating objects (curves and surfaces) and using them to form ships hull and deck. Two methods for forming a hull shape: extruding a surface from a midship section, and lofting a surface through given sections. Method to create and fit a deck.

55

Tutorial 3 Asymetric Hull Catamaran:

Design the outboard half of the hull by extrusion Generate the inboard half of the hull by modifying a mirrored copy of the outboard half Design the tunnel as an integration of several panels Fit a deck between a centerline and a deck edge curve Construct a pilot house using a ruled and a swept surface

95

ii

Table of Contents

Tutorial 4 Pocket Cruiser:

Design a small, heavy displacement cruising yacht. Tutorial 4 goes beyond basic hull lines and completes the superstructure as well. The shell is built up much as a real boat would be constructed: first, the hull is created; and then the transom, keel, deck and cabin are added.

121

Tutorial 5 Ro-Ro Carrier

Create a voluminous hull using a vertical panel running from bow to stern which joins the formed lower portion of the hull along a knuckle line. The hull also has a bulbous bow and a stern bulb. Compose hull using four surfaces, with bow and stern bulbs are added as separate objects.

135

Tutorial 6 Oil Rig

How Autoship generates accurate large-assembly models such as oil rigs. Creating an entire model using copy, mirror, and group features based on the simple geometry of one quarter of the structure. Create minimum number of necessary individual components then use symmetry of the design to complete the model.

151

Appendix Auto3D Module

165

iii

Introduction
Introduction to Autoship/Autoyacht 8.2
This chapter contains the following topics: Whats in this Guide Welcome to Autoship Systems Corporation Whats New in Autoship/Autoyacht 8.2 Contact Information for Technical Assistance Contact Information Head Office

Whats in This Guide?

The purpose of this guide is to assist users in installing, starting, running, and using Autoship/Autoyacht release 8.2 (for convenience, only the term Autoship will be used). Once the program is running, the fully online and context sensitive help system is the primary source of assistance and reference. This printed guide specifies the system requirements needed to run Autoship, gives instructions for installing and starting the program, and outlines the range of available online and printed help resources. The section entitled Tutorials contains six step-by-step exercises that introduce the basics of designing and modelling with Autoship. Users upgrading from previous versions of Autoship will want to review the Whats New section of this user guide and the sections Whats New in 8.1 and Whats New in 8.2 of online help; for
1

Introduction

more details on program changes and bug fixes, see the History.doc and Readme.doc files. Both this guide and the online help system (Autoship Help) cover all features within Autoship 8.2 Pro; for a list of differences between Autoship Pro, Autoship Standard, and Autoyacht versions, see the Introduction section of Autoship Help.

Welcome to Autoship Systems Corporation

Since its founding in 1980, Autoship Systems Corporation (ASC) has become the worlds leading PC software developer for the naval architecture and marine shipping industries. Our mission is to provide quality software solutions for the marine industry. Autoship Systems Corporation is the foremost supplier of marine design and construction programs worldwide, with over 1,700 installations in more than 50 countries and an international network of Autoship dealers. Our roots are in providing CAD/CAM products for the ship/boat design market, where ASC was the first to deliver a ship design tool on a PC platform, first to develop a Windows-based ship design tool, and was a leader in using the industry-standard Nurbs 3-D hull modeling tool. Recently ASC broadened its product lines and services, which now include onboard stability and stowage planning software for ship owners and marine cargo handlers. Autoship Systems success is derived from building upon continuous leading-edge innovation, unsurpassed quality, and a strong tradition of responding to our customers needs. This tradition of success is continued with the new functionality found in this latest release of the Autoship program.

Whats New in Version 8.0

Introduction
This chapter provides an outline of the functions, features, and tools that are new or modified in Autoship release 8.0. For detailed information on these topics, refer to the individual subjects in the online help system (see below). See also the History.doc and Readme.doc files (found in \Program Files\ASC\Autoship8 \Documents) for a listing of fixed bugs. To learn what features were added in Versions 8.1 and 8.2, consult the sections Whats New in 8.1 and Whats New in 8.2 in online help.

Autoship Help - The Online Help System

Autoship Help, provided with this release, is a fully online context sensitive help system integrated into the Autoship program. There are two main ways to access Autoship Help: 1. Run Autoship Help Click on the Help menu in Autoship, and then select Autoship Help. 2. Context Sensitive Help Point at the part of the screen that help is required for and press F1; or use the help buttons in the dialogue boxes: both will activate the help system, which will display the highest level of help contained for the desired topic. Navigate from there to more specific information using any of these methods: the system of links to related topics the Table of Contents, provided on the left of the help screen
3

Introduction

the Index tab at the top of help screen the Search tool tab at the top of the help screen

Changes in Autoship 8.0:

New Offset Report Format The format in which offset tables are presented in reports has been changed to be closer to naval architecture practice. ORC IMS Offsets Export The Offshore Racing Council International Measurement System offset file provides data on hull, keel and rudder for use in their Velocity Prediction Program (VPP). This file has the extension ".off", and is meant to be partnered with a ".dat" file generated by ORCs ORCEDIT.EXE program. Changes to Geometry File Export Important Note: These changes significantly alter the way the Autoship program behaves. Previously, Autoship made one Part (name "HULL", unless changed by user at a prompt) containing one Component (name C1). Now a separate component is created for each object in the selected group. Thus each surface, polyobject or group contained in the export group becomes a different component. Instant Hydrostatics Autoship 8.0 provides instant hydrostatics information through the small H button located in the bottom row of controls.

New in Autoship 8.0

Surface Edge Match to Curve The Attach Surface dialogue has been changed to support a new feature of the program. In addition to the old choices of "Attach to Surface" and "Attach to Curve", there is now a third option, "Match to Curve". Choosing this option, selecting a curve to match, entering a tolerance causes the program to match the selected surface edge to all or part of the curve. This feature has been added to compensate for the loss of ability to trim attached surfaces. Surface Blends There is a new tab in the Create Surface dialogue, labeled "Blend", providing the ability to produce fillets and chamfers. Grouping of Control/Edit Points It is now possible to select and move multiple edit and control points. Trimmed NURBS Surfaces Previous to this release, trimming a surface produced a polyobject, which could be regenerated but not edited. Now the trimming operation is performed directly on the NURBS surface. Further editing of the surface or trim curve(s) results in an immediate update of the trim. Surface Mesh Layout In previous releases surface mesh points were spaced equally in parameter space, with extra points at chines. This has been replaced with a system in which there is a mesh node at each knot, including chines, and the number of mesh points between knots depends on the degree of the section.
5

Introduction

DXF Output of Flattened Developable Surfaces This now brings up the DXF output dialogue which allows the user to select many of the same output options as for other objects. Cutting Surface-embedded Curves at Crossings In select mode, the bottom right tool icon, which was previously used only for trimming surfaces, now has two functions. Measurement Tool Next to the information button on the bottom row of controls is a small button labeled "M". Clicking on this control brings up a frame containing measurement information. Clicking on the "M" button again removes the measurement frame.

Contact Information

Contact Information
There are two main ways to contact Autoship Systems Corp.: Contact our technical support department for technical assistance. For other inquiries, contact our head office.

Technical Support:
Our technical support department is available for direct telephone inquiries on weekdays from 08:00 to 17:00 Pacific Standard Time. You can also fax or email questions at any time: Tel: Fax: Email: (+1) 604 254 4171 (Extension 104) (+1) 604 254 5171 [email protected]

Contacting Autoships Head Office:

If you would like more information about Autoship Systems Corporation and our products, please do not hesitate to contact us at: Telephone: Fax: Surface Mail: (+1) 604 254 4171 (Extension 102) (+1) 604 254 5171
Autoship Systems Corporation Suite 312, 611 Alexander Street Vancouver, BC, Canada V6A 1E1

Email: Sales Dept: Our web site:

[email protected] www.autoship.com

Introduction

Installation
This chapter contains sections that detail: system requirements necessary for running Autoship installation instructions hardware lock installation

System Requirements
The following table shows the minimum and recommended system requirements for running Autoship: Minimum CPU Intel processor, 100 MHz recommended minimum Recommended Intel processor 1 GHz or higher (for best results) 128 Mb (Windows 95) 256 Mb (Windows NT/2000/XP)

Memory

64 Mb (Windows 95) 128 Mb (Windows NT/2000/XP) 20 Mb 1024x768 resolution, 256 colors *

Free Hard Disk Space Graphics

1280x1024 resolution, True Color

Mouse Any Windows pointing device *Operation is possible at 256 colors, but for rendering to function correctly 32k colors or more are needed.
9

Installation

Program Installation
1. First, you need to install the hardware lock onto your system. Note: If you do not install the hardware lock, Autoship will run in test drive (or demo) mode and will not be able to save any files or print any reports (See Installing the Hardware Lock below for hardware lock installation details.). 2. Then, with Windows running: If you are installing from a CD, run Setup.exe found on the CD. If you are installing from floppy disks, run Setup.exe found on the Authorization disk. If you are installing from files on your hard drive, run Setup.exe on your hard drive.

3. Follow the instructions given by the install program. 4. When you get the message that installation is complete, respond by clicking OK. 5. After the installation is complete, you will see the Autoship icon on the screen. 6. To start Autoship, click on the appropriate icon or option from Start Programs Autoship.

10

Installation

Hardware Lock Installation

Description The hardware lock is a small electronic device that is connected to the parallel port of your computer. (Note: If you have a network hardware lock, only one lock is used for all computers on the network. See below for details.) You need the hardware lock in order for Autoship to run in normal operating mode. Otherwise, the program will only run in demo mode. Keep the lock in a safe place when not in use. As outlined in the Licensing Agreement, you are exclusively responsible for the hardware lock. You may be required to purchase an additional software license if the hardware lock is lost or stolen. Precautions Before beginning the installation, close all running programs. Only network locks may be daisy-chained. For a local station installation, a single lock may be configured for all the programs the user is authorized to use consult your dealer. Certain local printers may interfere with the operation of the lock. If this is the case, try a different printer driver, or install another parallel port.

11

Installation

Windows 95, Local Station

1. Connect the hardware lock to the parallel port. 2. If you had a printer connected to the same parallel port, connect the printer to the free end of the lock. 3. Install Autoship as discussed above.

Windows NT/2000/XP, Local Station

1. If the Autoship installation program detects a Windows NT Window 2000 or Windows XP operating system, you will be prompted: Would you like to copy the NT lock driver files to your computer? You must respond Yes, unless you have previously installed the NT lock driver (The NT lock driver is required so your NT operating system can communicate with the parallel port.). You will then be asked where you want to copy the NT lock driver files to. 2. Continue with the installation of Autoship as discussed above.

12

Installation

Hardware Lock Installation, Network System

If you have purchased a network lock, you will have received a separate floppy named Network Lock Driver. 1. Connect the network lock onto the parallel port on any one of the computers in your network. 2. The Network Lock Driver floppy contains 3 directories: \DOS (for Windows 3.11) \NW (for NetWare) \Win32 (for Windows 95 and Windows NT/2000/XP) Each directory contains a readme.txt file. Follow the directions appropriate for your operating system. 3. Install Autoship onto each station on your network from which it will be run, following the installation instructions above.

13

Installation

14

Getting Started
Introduction
This chapter contains sections that detail: Starting Autoship Using Autoship and accessing the context-sensitive Help system Exiting Autoship Upgrading Autoship

Starting and Exiting Autoship

To start Autoship, go to Start Programs Autoship and click on the Autoship 8.2 icon. To become familiar with the main screens, features, and organization of Autoship, point at any active window, dialogue, or feature on the screen and press F1. The highest-level of available Help information will appear for the feature you selected, and will contain links to more detailed information. To exit Autoship, go to File Exit. Be sure to save any changes made to your project files before closing down the program.

References and Help Resources

This section describes the help resources available to Autoship users. Autoship Help (the online help system) is the primary resource, and it can be accessed at any time.

15

Getting Started

How to Access Online Help:

Run Autoship Help Click on the Help menu in Autoship, and then select Autoship Help. Context Sensitive Help Point at the part of the screen that help is required for and press F1; or use the help buttons in the dialogue boxes: both will activate the help system, which will display the highest level of help contained for the desired topic. Navigate from there to more specific information using any of these methods: the system of links to related topics the Table of Contents, provided on the left of the help screen the Index tab at the top of help screen the Search tool tab at the top of the help screen

Types of Help Available:

Online Familiarization and Overview The onlne help section entitled Introduction to Autoship gives an overview of the software. Reviewing the table of contents will provide a good introduction to the functional organization of the Autoship program. Index and search utilities are also available within the Help system.

Program Reference: Context-Sensitive Help Autoship includes context sensitivity in the main screen (see How to Access Oneline Help above).

16

Getting Started

Detailed information on the softwares features, and how to use them, is available in the User Interface section of the help system. The help system can be accessed by using the Help Menu in the main screen menu bar, or by using context sensitive help (see How to Access Online Help above). The Basic Functions section in the Help system explains how to perform many of the basic operations involved in using Autoship.

Online Technical References The following technical and theoretical references are provided in the Help system: Basic Concepts Autoship as a surface modeler, Nurbs .vs. polygonal models. Technical Reference theoretical basis and detailed explanations of the functions performed on surface models by Autoship code.

Tutorials The tutorials in this guide are a series of increasingly challenging step-by-step projects that help develop the skills needed to use Autoship as a design tool. It is assumed that users are already familiar with the main screens and tools of the system, and know how to use the Help system to answer basic questions. Example tutorial files are found in \Program Files\ASC\Autoship8\Tutorials. Frequently Asked Questions Within the online help system is a list of the most frequently asked questions regarding the use of Autoship, with the answers provided by Autoship Systems Corporations technical support department.

17

Getting Started

Contact Information Technical Assistance Technical assistance is available as outlined in Contact Information on page 7. Further Training For advanced and complex projects, you should take an Autoship training course. Contact Autoship Systems, or your Autoship dealer for schedules and locations of upcoming courses, or for customised training.

Where to Find Help Resources

There is a complete range of Help resources available to assist users at all levels: Help Found Online The Autoship/AutoYacht Help Sytem General Familiarization and Overview Whats New in 8.1 and 8.2. These sections contain information about the program features added in releases 8.1 and 8.2, with links to the full documentation. Program Reference - context-sensitive online Help containing specific information on how to use Autoship tools, interface, features, and basic functions. Technical references help with the purpose, details, and theory behind key concepts and features in Autoship.

Help Found in Print This User Guide

18

Getting Started Installation and Familiarization information. Detailed Tutorials (in this User Guide).

Getting Started

Note that this guide is also available in .pdf format on your Autoship/Autoyacht program CD.

Autoship Systems Corporation Contacts and Technical Assistance Autoship System Corporations technical assistance via telephone, email, or fax. Autoship System Corporations instructional courses on the Autoship program.

Updating Autoship
When you update Autoship, the installation procedure is the same as for a new installation. All necessary program files are updated. No data you have saved will be adversely affected by updating the installation.

19

Getting Started

20

Tutorial 1

Tutorials
Introduction
This chapter takes you through six tutorials: Chined Hull Planing Boat; Round Bilge Hull; Asymmetric Hull Catamaran; Pocket Cruiser; Ro-Ro Carrier; and Oil Rig. Completed examples of these tutorial projects are found in \Program Files\ASC\Autoship\Tutorials. It is suggested that you first create a new folder to contain the tutorial projects you will construct (we suggest the filename MYTUTS). We recommend that Autoship Pro and Standard users do these tutorials in the order that they are presented, as the sophistication of the design methods increases accordingly. Autoyacht users should begin with tutorial one; however, because Autoyacht does not support developable surfaces, take care to create the bottom using a ruled surface. Tutorials 2,5, and 6 cannot be constructed in Autoyacht due to the size of the vessels. With Autoship there are always, generally, several ways to accomplish a given task. Often the best approach will be determined by the requirements of subsequent steps. In these tutorials, we have not attempted to show the only, or the best way to deal with a certain aspect of the model, but instead have undertaken to provide a broad base of approaches from which the knowledgable user can choose the one best suited for their particular circumstances.

21

Tutorials Note: When more information is required than is available in these tutorials, access Autoship Help through one of these three methods: press F1 and help will appear for the window, dialogue, or feature currently active on the screen use the Help menu in the Menu Bar use the Help buttons provided in the dialogues

22

Tutorial 1

Tutorial 1 - Chine Hull Planing Boat

3m

1.9m 10m Figure 1-1 Chine hull planing boat

1.1 Introduction Chine Hull Planing Boat

In Tutorial 1, you will: Design a deck edge Design a chine Design a centreline Create the bottom panel as a developable surface Create the side panel as a ruled surface Add a cylindrical transom Obtain offsets Obtain hydrostatics Tutorial 1 shows how to create a hull using developable and ruled surfaces and demonstrates how to create and fit a cylindrical transom. It also introduces the idea of attaching the end of a curve to a point and discusses the topic of tangency at the end of a curve. In addition, it shows how to obtain offsets and hydrostatics.1.2 Starting Out The model we've constructed, TUT1.PR3, is a very simple, little planing hull. You may want to review this model before continuing.

23

Tutorials To begin: 1. Select File-New. 2. Select Settings-Units, choose Meters and Tonnes, and click OK. 3. Select Settings-Preferences. 4. Click the Coordinate System button. 5. Click the Naval /Aircraft (US) radio button. This orients the coordinate system so that aft, starboard, and up are positive directions; while forward, port, and down are negative directions. 6. Click OK in the Coordinate System dialogue and click OK again in the Preferences dialogue. 7. Select File-Save. In the Project Info dialogue , under Name, type a descriptive message for the project (for example, 10m Planing Hull). Notice that under Details, 0 objects have been defined. Click OK. 8. In the Save Project dialogue box that appears, type MYTUT1.PR3 for the File Name. Save the project in your new directory called MYTUTS. 9. Click OK.

24

Tutorial 1

1.3 Designing a Deck Edge

This exercise introduces two concepts: I) working to reference points, and ii) curve colours. i) In some instances, you may want to have several curves end at the same location. Attaching the ends of the curves to a common point accomplishes this purpose. ii) Autoship provides the ability to assign colours to curves. In these tutorials, well adopt the convention that design curves will be yellow, construction curves will be blue and intersection curves will be purple. All other curves will remain red the default colour.

To create a Reference Point at the Forward End of the Deck: 1. Click on the Create Mode button, which places Autoship in Create mode. 2. Click the Create Point button. 3. In the Create Point dialogue, select the Free tab, type the following information, and click OK.

Field
Point Name Location

Entry
Deckfor L = A0.3; T = 0; V = 0.9

4. Hold down the Shift key and click on the Zoom Extents button to zoom out in all views. (See Figure 1-2.)

25

Tutorials

point Deckfor

Figure 1-2: The point Deckfor. Note that the x is the point Deckfor, while the + is its base point.

To create a curve to represent the deck edge from bow to stern: 1. Click the Create Mode button. 2. Click the Create Curve button. 3. Below Curve Name, click the red bar labelled Colour. In the AutoCAD Colour dialogue, under Standard Colours, select the yellow box and click OK. 4. In the Create Curve dialogue, select the Free tab, type the following information and click OK. Field
Curve Name Parameters End 1 End 2

Entry
Deck Edge Control Points = 5; Max Degree = 3 L = 1; T = 1.5; V = 0.8 L = 9; T = 1.5; V = 0.8

26

Tutorial 1 5. Hold down the Shift key and click on the Zoom Extents button. (See Figure 1-3.)

Figure 1-3: The curve Deck Edge To attach the forward end of curve Deck Edge to reference point Deckfor Curve: 1. With the curve Deck Edge selected, (check the Object display box at the top right of the screen) click the Edit Mode button. Ensure that you are working with control points rather than edit points: click the Control/Edit Points button and see the button change; for edit points, the points show on the curve in the button; for control points, they do not. On the main screen, control points are indicated by a circle at each vertex, edit points are indicated by a square. 2. Select the first vertex (vertex 0). Watch the Vert readout at the left of the screen to ensure vertex 0 is selected. 3. Click the Attach button. 4. In the Attach Curve dialogue, Under Action, pick Attach to Point, under Attach to point, select Deckfor and click OK. (See Figure 1-4.)
27

Tutorials

Figure 1-4: Attaching curve Deck Edge to point Deckfor Note: we could have attached End 1 of the curve Deck Edge to the point Deckfor in the Create Curve dialogue. However, we wanted this curve to have shape and if we had made the attachment in the dialogue then the curve would have been a straight line between Deckfor and the aft coordinates: 9a, 1.5, 0.8.

1.4 Creating the Chine Curve

We will create the chine in a multi-step process: first, we will create the point Chinefor to represent the forward-most point of the chine; then we will copy the deck edge; next we will move the copy to the correct position; and then we will attach the forward end of the chine curve to the point Chinefor; and finally, we will re-shape the Deck Edge and Chine curves.

28

Tutorial 1 To create a Reference Point for the forward end of the chine: 1. Click the Create Mode button. 2. Click the Create Point button. 3. In the Create Point dialogue, select the Free tab, type the following information, and click OK. (See Figure 1-5.) Field
Point Name Location

Entry
Chinefor L = 1; T =0; V = 0

Point Chinefor

Figure 1-5: Reference point at the forward end of the chine

29

Tutorials To copy the Deck Edge curve to use as the Chine: 1. Click the S Side button to better see the objects of interest. 2. Select the curve Deck Edge. 3. Hold down the Shift key and click on the Clone button to copy the Deck Edge curve. Note the new curve is yellow. 4. In the Copy dialogue , under Name for Copy change the name to Chine and click OK. To move the curve Chine: 1. Make sure that the curve Chine is selected. (If it isnt, press the Spacebar repeatedly until the Object display box at the top-right of the screen shows Chine.) 2. Right-click on the Move button. 3. In the Move Selection dialogue, for V enter 1.3 and click on OK. (See figure 1-6.)

Deck Edge curve

point Chinefor

Chine curve

Figure 1-6: Chine curve moved down

30

Tutorial 1 To attach the curve Chine to the point Chinefor: 1. Switch to Edit mode. 4. Select vertex 0 of the curve Chine, by clicking on that vertex. Watch the Vert readout at the left of the screen to ensure vertex 0 is selected. 5. Click the Attach button. 6. In the Attach Curve dialogue , Under Action, pick Attach to Point, under Attach to point, select Chinefor and click OK. To move the curve Chine inboard 0.3m: 1. Click the Top view button. 2. Switch to Select mode. 3. With the Chine curve selected, right-click on the Move button. In the Move Selection dialogue , for T enter P0.3 and click OK. (See Figure 1-7.) Note: since the forward end of the Chine is attached to Chinefor, the curve will change shape when it is moved.

Figure 1-7: Chine and Deck Edge curves

31

Tutorials To edit the Deck Edge Curve: 1. Select the curve Deck Edge. 2. Switch to Edit mode. 3. Ensure Control Point mode is selected. 4. Move vertex 1 to L = 1.5A and vertex 2 to L = 4A by selecting each point and using the arrow keys on the keyboard. Watch the readout at the left of the screen to ensure the correct coordinates are obtained. Press Return to anchor the vertex at the intended position. 5. Suppose the chine had to pass through the points L=2.25, T=.8 and L=4.8, T=1.175, heres an easy way to set that up: Right-click on the Edit mode button. The Curve Editor dialogue shows the positions of the edit points on the curve. Set point 1 to L=2.25, T=.8 and point 2 to L=4.8, T=1.175 and click Fit. Click the x in the top right to close the dialogue.

Figure 1-8: Deck Edge and Chine filled out 6. You may wish to switch to S Side view and edit the shape of the Chine curve by moving the vertices up or down.
32

Tutorial 1

1.5 Creating a Curve to Represent the Centreline

To create a curve: 1. Click the S Side view button. 2. Click the Create Mode button. 3. Click the Create Curve button. 4. In the Create Curve dialogue , select the Free tab, type the following information, and click OK. (See Figure 1-9.) Field
Curve Name End 1 End 2 Colour

Entry
Centreline L = 1; T = 0; V = -1 L = 9; T = 0; V = -1 Yellow

5. Following the method described previously, attach Vertex 0 of curve Centreline to the point Chinefor.

Figure 1-9: Centreline curve

33

Tutorials

1.6 Ensuring Fairness Along the Stem

This design calls for the stem section below the chine to fair smoothly into the straight stem section above the chine. Currently, the Centreline curve defines the stem below the chine and the straight stem is a line drawn from the forward end of the Deck Edge curve to the forward end of the Chine curve. In Autoship, the end of a curve lies at the same position as the end control point, and is tangent to a straight line drawn from the end control point to the next control point. Therefore, by re-positioning the second control point of the Centreline curve, we can ensure the stem section below the chine is tangent to the straight stem above the chine. To achieve this, the second control point could be located anywhere below the chine on the extension of the straight stem line. To position the vertex: 1. With the curve Centreline selected, and in S Side view, make sure you are in Control Point mode. 2. Select vertex 1. Note: We have calculated the intersection of the straight stem line with V = -1 (the current height of vertex 1) to be at L = 1.83A 3. Move the control point forward to L = 1.83A by clicking in the L coordinate box near the upper left of the screen, typing 1.83A and Enter. 4. Adjust the curvature of the fore foot by moving vertex 2 of the Centreline directly forward. (See Figure 1-10.) Tip: use the left-right arrow keys on the keyboard to avoid moving the vertex up or down.

34

Tutorial 1

vertex 2

vertex 1

Figure 1-10: Fairing the stem

1.7 Creating the Bottom as a Developable Surface

We will create the bottom panel as a developable surface. Developable surfaces are favoured when working with sheet material, such as aluminum or plywood, as the surface may be easily formed. In Autoship, a developable surface is created from two curves, however, as it is dependant upon those two curves it is only editable by editing the curves. A developable surface is updated after editing the curves by selecting the surface and clicking on the Edit Regenerate menu option. To create a developable surface: 1. Click the Create mode button. 2. Click the Create Surface button. 3. In the Create Surface dialogue, select the Develop tab, type the following information, and click OK: Note for Autoyacht Users: Autoyacht cannot create developable surfaces. If you are an Autoyacht user, click on the Ruled tab.
35

Tutorials Field
Surface Name Curves Tolerance Start Options End Options Spread fan Tips

Entry
Bottom Chine Centreline 0.0005 Straight Extrapolate Curvature Check

Note: Start Options governs the beginning edge of the surface (r = 0), End Options governs the ending edge (r = 1). Straight causes the edge of the surface to be a straight line between the ends of the two curves. Extrapolate Curvature creates the surface as if it extended beyond the end of the curves but truncates it at the ends of the curves, thus creating a curved edge. 4. Click the Mesh button to see the ruling lines. (See Figure 1-11.)

Figure 1-11: Bottom surface, profile view

36

Tutorial 1

1.8 Creating the Topsides as a Ruled Surface

Ruled and developable surfaces are similar, but not identical. Both surfaces are created by constructing a series of ruling lines between two curves. The rows of the surface are derived from the ruling lines. For a ruled surface, the ruling lines connect a given parameter value on one curve to the same parameter value on the other curve. The arrangement of the ruling lines on a developable surface depend on the relative shape of the two curves and are determined by extensive calculation. Since developable surfaces are merely sections of cones and cylinders linked together, the shape can be manufactured from sheet material with just simple straight-line bending. A ruled surface usually has compound curvature, which means the material must be plastically deformed to manufacture the shape. To create a ruled surface: 1. In Create mode, click the Create Surface button. 2. In the Create Surface dialogue, select the Rule tab, type the following information, and click OK. Field
Surface Name Curves

Entry
Topsides Deck Edge Chine

3. Click the Mesh button to see the ruling lines. (See Figure 112.)

37

Tutorials

Figure 1-12: Topside surface, profile view (note the visibility of the Bottom surface has been turned off)

1.9 Seeing the Results

1. Click the Mesh button to turn off the surface mesh. 2. Right-click on the Contours button to open the Contours dialogue . 3. Set stations, waterlines, and buttocks appropriate to your model and click OK. Tip: Click on the Stations radio button, set Station Spacing to 1, click on the Group button, set Last to 10 and Step to 1 and click on OK. Click on the Buttocks radio button, click on the Group button, set Last to 2 and Step to .5 and click on OK. Click on the Waterlines radio button, click on the Group button and click on OK. 4. Click the 4 View button. 5. With both surfaces selected, click the Contours button.

38

Tutorial 1

6. Experiment with modifying the lines by moving the two reference points Deckfor and Chinefor and editing the shape of the curve Chine to see how they affect the two surface panels. Remember to update each surface by selecting it and then clicking on Edit - Regenerate.

1.10 Adding Flair to the Topsides

In this exercise we will add another column of vertices to the Topside surface so that we can introduce some flair at the forward end. To add another column of control points and fair the shape: 1. Turn off the contours by clicking on the Contours button. 2. Select the surface Topsides, and in Edit mode, pick the upper column of control points. Note: The rows and columns of a surface may not be oriented the way you expect. For ruled and developed surfaces, the rows always match the curves used, thus the columns are oriented the opposite way. For columns, the Rows / Columns button should show vertical lines. 3. Click on the Add Row or Column button (make sure you are working with columns, not rows). 4. Insert a column at a proportion of .35. (This percentage works out well for the flair shape.) 5. In the top view, move the second vertex (Row 1, Col 1), and perhaps the third also, aft and inboard slightly. (See figure 113.)

39

Tutorials

Figure 1-13: Editing column 1 of Topside surface 6. View the results by turning on the contours. You will notice that the stations display as straight lines rather than curves. This is because the curvature and resolution of the surface Topsides are still at the low values that a ruled surface is created with. 7. Go to the Attributes dialogue (Edit Attributes menu) and, for the surface Topsides, set the CDeg to 2 and CRes to 20. Note: if you move the Col 1 vertex at the stem to develop curvature in the stem, you will destroy the smooth transition of the stem to the fairbody. If a curved stem is desired, you will have to calculate a new position for vertex 1 of the curve Centreline based on the relative positions of surface Topsides Col 1 and Col 2 vertices at the stem, move the vertex and then regenerate the Bottom surface. 8. Turn off contours and switch to Select mode to begin the next exercise.

40

Tutorial 1

1.11 Adding a Transom

This exercise introduces the Arc curve type. The arc will be extruded to form a cylindrical transom which will then moved into position and trimmed off at the hull. This transom will have a 4m radius and be raked aft 9 degrees. To create the 4m radius curve: 1. In Create Mode, click the Create Curve button. 2. In the Create Curve dialogue, select the Arc tab, type the following information, and click OK: (see figure 1-14.) Field
Name Plane Centre Angles Semi Axes Colour

Entry
Transom Shape
Top L = 0, T = 0, V = 0 Start = 0 End = 25 Circular checked Radius = 4 Blue

41

Tutorials Note: we estimated that an angle of 25 degrees would produce a curve slightly wider than the half-breadth of the hull.

Figure 1-14: Transom Shape curve

To create the transom surface: 1. In Create Mode, click the Create Surface button. 2. In the Create Surface dialogue, select the Extrude tab, type the following information, and click OK: (see figure 1-15.)

Field
Surface Name Curve Vector Column Mesh

Entry
Transom
Transom Shape

L = 0, T = 0, V = 2
Number = 2 Max Degree = 1

Note: we could have created the transom at the intended rake angle by specifying an L component for Vector. However, this would not have resulted in a true cylindrical surface.

3.
42

Click the S Side view button.

Tutorial 1

Figure 1-15: The Transom surface

To rotate the Transom surface: 1. Select the Transom surface. 2. Right-click on the Rotate button. 3. In the Rotate dialogue, type the following information and click OK: (See Figure 1-16.) Field
Axis Angle Centre

Entry
Transverse

9
L = 0, T = 0, V = 0

43

Tutorials

Figure 1-16: The Transom surface rotated

To reposition the Transom surface: 1. With the Transom surface selected, click the Move button. 2. Drag the Transom surface to a position at the aft of the vessel where it extends above the Topside surface and below the Bottom surface, and then release the mouse button.

44

Tutorial 1 Tip: Remember that the displacement of the object originates at its base point which in this case is at the origin. (See figures 1-17 and 1-18.)

Figure 1-17: Moving the Transom surface

Figure 1-18: The Transom surface repositioned

45

Tutorials

In order to trim the transom to the hull, we must obtain the curves describing the intersection of the Transom with both the Topside and Bottom, and then revise these curves to produce a single curve with which to trim the transom. To generate the intersection curves: 1. Select both the Transom surface and the Topsides surface. 2. Click the Surf-Surf Intersect button. 3. In the Surf-Surf Intersect dialogue, ensure that the correct surfaces - Topsides and Transom - are displayed, enter a meaningful tolerance, i.e. 0.0005m and click on OK. This process will generate two intersection curves one embedded on the Transom surface, the other embedded on the Topsides surface. We should rename them using more meaningful names. We will use a naming convention for intersection curves: the curve name will contain the two surface names separated by a -, the first surface name will be the surface the curve is embedded on. Thus Topsides Int1 should be renamed to Transom-Topsides and Transom Int1 should become Topsides-Transom. 4. Select Edit Attributes, to call up the Attributes dialogue. Click on the curves button within that dialogue. 5. Click on the name Topsides Int1 and then click on the Properties button. 6. Rename Topsides Int1 to Transom-Topsides. 7. Click the bar beside Colour, pick Purple and click OK 8. Click OK. 9. Similarly, rename Transom Int1 to Topsides-Transom and set its colour to purple, then click OK.
46

Tutorial 1 10. Select both the Transom surface and the Bottom surface. 11. Click the Surf-Surf Intersect button. 12. In the Surf-Surf Intersect dialogue, ensure the surfaces Bottom and Transom are selected, enter a meaningful tolerance, i.e. 0.0005m and click on OK. 13. Rename the curve Transom Int1 to Bottom-Transom and set its colour to purple. 14. Rename the curve Bottom Int1 to Transom-Bottom and set its colour to purple. To revise the intersection curves: 1. In the Attributes dialogue, with Curves selected, click on the None Visible button, and then click in the Vis. column for Transom-Bottom and Transom-Topsides to turn on their visibility. Click on OK. 2. At the main screen, click on the Show Surfaces button to turn off the visibility of surfaces. 3. Click on the Show Points button to turn off the visibility of points. 4. Switch to Front view. 5. Select the curve Transom-Bottom and switch to Edit mode. 6. Click on the Join Curves button. 7. In the Join Curves dialogue, under New Name rename the curve to Transom Trim, under Join Transom-Bottom + select the curve Transom-Topsides, un-check Keep Originals, set the colour to light blue and click on OK. In order to use the new curve Transom Trim to trim the Transom surface, it must be a closed curve. This means both ends of the curve must either contact a surface edge or be positioned at the same location. In the absence of a deck surface with which to obtain an intersection curve to trim off the top of the Transom surface, we
47

Tutorials will extend the top of the curve Transom Trim to the centreline edge of the surface. 8. Switch to Edit mode. 9. Click on the upper-most vertex. Ensure you have selected the end vertex by pressing the F4 key a few times and watching the Vert display at the left of the screen when the number does not change, the end vertex is selected. 10. Insert another vertex at the same location as the end vertex: press the F3 key once and then click on the Add Control Pt button. In the Insert dialogue, set Proportion to 1 and click on OK. 11. Press the F4 key to move to the new end vertex. 12. Move the new end vertex to the centreline: click in the T coordinate box at the upper left of the screen, type 0 and Enter. 13. If necessary, use the arrow keys on the keyboard to move the vertex up or down to cause the upper portion of the curve to be horizontal. 14. Switch to Select mode. (see figure 1-19)

48

Tutorial 1 Figure 1-19: Revised Transom Trim curve

To trim the Transom surface: 1. Turn on the visibility of surfaces by clicking on the Show Surfaces button. 2. Select the surface Transom. 3. Click on the Trim button. 4. In the Trim Surface Transom dialogue, under Available Curves select Transom Trim and click on OK. Answer Yes to the appropriate Keep this Domain ? prompt and No to the other. To trim the Topsides surface: 1. Click on the 4 View button. 2. Select the surface Topsides. 3. Click on the Trim Surface button. 4. In the Trim Surface Topsides dialogue, under Available Curves select Topsides-Transom and click on OK. Answer Yes to the appropriate Keep this Domain ? prompt and No to the other. To trim the Bottom surface: 5. Select the surface Bottom. 6. Click on the Trim Surface button. 7. In the Trim Surface Bottom dialogue, under Available Curves select Bottom-Transom and click on OK. Answer Yes to the appropriate Keep this Domain ? prompt and No to the other. 8. Create a group of the three surfaces:
49

Tutorials a. Select the three surfaces select one, and then while holding down the shift key, select the others you must click on the white outline of the surface. Note that the object box at the top of the screen displays Multiple Select. Select Arrange Group. In the New Group dialogue, enter a name for this group. For now, ignore the other settings in the dialogue.

b. c.

9. View the contours (Contours button). 10. View the rendering (View Render menu option) Note, the Para view must be visible for rendering to appear.

1.12 Generating Offsets

In Autoship, you can obtain offsets for both surfaces and curves. In this exercise, we will add the centreline, chine and deck edge curves to the group just created and then obtain offsets for the entire group. To add curves to the group: 1. With the group just created selected, click on the button showing Group in the top right corner of the screen to go the the Group Editor. 2. Add the Centreline curve: under Objects, click on the Curve radio button; from the pick list below that, select Centreline; click on the Add button. 3. Add the Chine and Deck Edge curves the same way and click on OK. To obtain an Offsets report: 1. Click on the Report - Create Offsets menu option. At the Offset Table dialogue, set a meaningful tolerance and click on OK.
50

Tutorial 1 2. The Report Editor will appear and show the offsets table. Note that the first three tables indicate station, buttock and waterline locations. The fourth table shows curves. The fifth table shows heights and the sixth table shows half-breadths at the currently defined stations, buttocks and waterlines.

When you are done viewing the report, click anywhere on the main screen, or click on the X button at the top right of the report editor to return to the main screen.

1.13 Obtaining Hydrostatics

Autoship offers two type of hydrostatics. The Instant Hydrostatics option displays hydrostatic values in a floating screen and is for use while fairing surfaces. The Report method produces a full hydrostatics report in the report editor. To obtain Instant Hydrostatics: 1. Click on the small H button at the left of the screen to open the Instant Hydrostatics window. 2. In the Instant Hydrostatic window that appears, click on the Group button. 3. In the Choose Hydrostatics Group dialogue that appears, select the group you last created and click on OK. (Note that you must actually click on the name.) 4. In the Instant Hydrostatic window, click on the Update button. Note: the Depth box shows the default depth value originally entered with the Project Info when setting up the project. This is the distance from the origin to the waterline. You can type a different value in the Depth box, or restore the default by clicking on the R button to the right of Depth. The Update button calculates the hydrostatics for this depth.
51

Tutorials Alternately, you can type in values for Mass and LCG and click on the S button to the right of Mass to have Autoship find the depth and trim corresponding to the given mass and LCG and then show the hydrostatics for that waterline. 5. Click on the small H button near the lower left of the screen to close the Instant Hydrostatics window.

To obtain a Hydrostatics Report 1. Select the group you last created. 2. Click on the Reports - Create - Hydrostatics menu option. 3. In the Hydro Parameters dialogue that appears, set the depth to -.4 and click on OK. 4. The Report Editor will open up and display the hydrostatics just calculated. Re-size the report window to full size by clicking in the middle box in the upper right corner. The scroll bar at the right can be used to shift the report up or down. 5. When finished, click on the Clear Report button (the x button) near the upper left corner and answer No at the save changes prompt. This will erase this report. Note: a new report is appeneded to the bottom of the existing report. Clearing the report ensures you will see the next report immediately upon opening the report editor. 6. Click on either the - button or the X button at the upper right to return to the Autoship main screen.

52

Tutorial 1

Figure 1-20: Chine hull planing boat

1.14 Summary
You have been shown how to create two types of surfacesthe developable and ruled surfacesand you have seen how these surfaces depend upon curves. You have also worked with embedded curves and have explored the uses of reference points for attachments. And you have also seen how to obtain offsets and hydrostatics.

53

Tutorials

54

Tutorial 2

Tutorial 2 Round Bilge Hull

28m

18m 240m

Figure 2-1: Round Bilge Hull

2.1 Introduction - Round Bilge Hull

The project in Tutorial 2 is a general cargo vessel of radius-bilge design. It also has a bulbous bow with thruster and a faired-in stern bulb. Tutorial 1 demonstrated how to create a hull using developable and ruled surfaces and how to create and fit a cylindrical transom. It also outlined various uses for curves, introduced the idea of attaching the end of a curve to a point and discussed the topic of tangency at the end of a curve. In addition, it demonstrated how to obtain offsets and hydrostatics. Tutorial 2 introduces additional methods of creating and refining curves and surfaces. It demonstrates two methods for forming a hull shape: by extruding a surface from a midship section and by lofting a surface through given sections; and one method to create and fit a deck. The learning objectives in Tutorial 2 are to:
55

Tutorials

Create a midship section with a radius bilge Generate a forebody shape as an surface extruded from the midship section Develop the bow rounding Work with shape and fairness Control flat of side Generate the aftbody shape as a surface lofted from curves Add a bow thruster by projecting a curve Add a bow thruster by surf-surf intersection Add a deck with camber and shear

The model we have constructed, TUT2.PR3, has the following particulars: overall length: 240m breadth: 28m depth: 18m bilge radius: 1m origin: under keel amidships You may want to review this model before continuing.

56

Tutorial 2

2.2 Starting Out

Create a new project: 1. Select File - New to prepare Autoship for a new project. 2. Select Settings - Units. Pick Meters and Tonnes, and click OK. 3. Select Settings - Preferences. 4. Click the Coordinate System button. 5. Pick Naval/Aircraft (US). This orients the coordinate system so that aft, starboard, and up are positive directions while forward, port, and down are negative directions. 6. Click OK in the Coordinate System dialogue box and click OK again in the Preferences dialogue box. 7. Select File - Save As. In the Save Project dialogue box that appears, type MYTUT2.PR3 for the File Name. Save the project in your new directory called MYTUTS. 8. In the Project Info dialogue box, under Name, type a descriptive message for the project, such as Tutorial 2. Note the Design Depth box at the bottom of the dialogue this is to provide a starting point for the Instant Hydrostatics calculations. Set Design Depth to 11. Click OK.

57

Tutorials

2.3 Creating the Midship Section

In this exercise you will learn how to create and form curves by creating a midbody curve and matching it to a circle. You will also learn how to create a surface by extruding the midbody curve forward to form the forward half of the hull. To form the Midbody Curve: 1. Click the Create Mode button. 2. Click the Create Curve button. 3. In the Create Curve dialogue box that appears, select the Free tab to create a free curve. 4. Type the following information and click OK when you have finished. Field
Curve Name Parameters End 1 End 2 Colour

Entry
Midship Curve Control Pts = 3 MaxDegree = 2 L = 0, T = 0, V = 0 L = 0, T = 14, V = 18 (the values of max beam and depth) Set to Yellow

Note: For this model, the longitudinal origin is at midships. We will create the midship curve at L = 0, thus positioning it at midships. This first step will also set up the basis for the models coordinate system. Your screen should look like Figure 2-2.

58

Tutorial 2

Figure 2-2: Midship Curve To form the basic hullshape at midships: 1. Click the Front view button at the left of the screen. 2. If the Midship Curve is not selected (when selected, the objects name appears in the Object box at the top, right of the screen) select it by pointing at it with the mouse and clicking the left mouse button. 3. Click the Edit Mode button. This places the program in Edit mode and displays the vertices that make up the curve. Ensure that you are working with control points rather than edit points. Click the Control/Edit Points button and see the button change. For edit points, the points show on the curve in the button; for control points, they do not. On the main screen, control points are indicated by a circle at each vertex, edit points are indicated by a square. 4. Select the middle vertex and drag it to max beam and to the baseline. Watch the LTV readout at the lower left of the screen. Release the mouse button when the vertex is at T = S14 and V = 0 and press Enter. See Figure 2-3.

59

Tutorials Tip: To position the vertex easily, switch to Grid Mode and set the Snap to 1: click the Grid button to turn Snap off and turn Grid on, increase snap by 10 times by pressing the + key or the up arrow at the right of the snap value, decrease with the - key or the down arrow.

Figure 2-3: Front view of Midship Curve Note: Select a point by clicking on it. Drag a vertex by pointing at the selected vertex, holding the left mouse button down, pulling the vertex to the intended position, then releasing the mouse button and pressing Enter. You can also move a vertex by selecting it, re-positioning the cursor with the arrow keys on the keyboard and then pressing Enter. 4. Make the middle vertex into a knuckle point: with the middle vertex selected, click the Toggle Corner button. Note that the vertex changes to green in color. To form a radius corner: 1. While still in Edit Mode, with the middle vertex selected, click the Radius Corner button.
60

Tutorial 2 2. In the Fillet dialogue box, specify a radius of 1.0, and click OK.

New knuckle vertices

Figure 2-4: Midship Curve with two new vertices as knuckles Note: This turns the selected corner vertex back into a regular vertex and adds two new vertices as knuckle points. (See Figure 2-4.) A surface extruded from this curve would have two knuckle lines (rows) along its entire length and so would be difficult to work with. We will remove the knuckle points while retaining the radius. To make a Bilge Circle template: 1. First, with the middle vertex selected, note the weight (W) value at the left. Normal vertices are set to 1. This vertex has been set to .707 by the radius routine. 2. Click the Create Mode button. 3. Click the Create Curve button. 4. In the Create Curve dialogue box that appears, select the Arc tab, type the following information and click OK when you are finished. (See Figure 2-5.)
61

Tutorials Field
Curve Name Plane Centre

Entry
Bilge Circle Front L=0 T = S13 V=1

Semi-Axes Angles

Circular = checked Radius = 1.0 Start = 0 End = 360

5. Zoom in on the Bilge Circle curve: click the zoom button, point above and to the left of the top of the curve, hold the mouse button down and drag a zoom box diagonally to below and to the right of the bottom of the curve and then release the mouse button 6. Go to Edit Attributes and set Midship Curve CRes to 150.

Figure 2-5: Bilge Circle Template To match the Midship Curve to the Bilge Circle Template:
62

Tutorial 2 1. Select Midship Curve. (Press the space-bar to scroll through the objects, watch the Object Box at the top, right of the screen.) 2. Switch to Edit Mode. 3. Make sure Control Points, not Edit points are selected. 4. Insert a new vertex after vertex 1: click on vertex 1. Look at the Vert display at the lower left of the screen to make sure you have the correct vertex. 5. Click the Add Control Pt button. 6. In the Insert dialogue box, select Refine and click OK. Refine inserts another vertex without chaning the shape of the curve. To form the Midship Shape: In order to avoid having longitudinal knuckles in the hull shape, we must remove the knuckle points in the Midship Curve. 1. Select vertex 1 and click the Corner button. 2. Select vertex 4 and click the Corner button. This turns the two knuckle points into regular points. 3. Use the arrow keys on the keyboard to move the lower points (vertices 1 and 2) transversely and the upper points (vertices 3 and 4) vertically until the bilge radius portion of the midship curve is the same shape as the template curve. You may have to adjust the snap value in order to move the vertex by small distances. (See Figure 2-6.) Remember to press Enter when you have finished positioning each vertex. Tip: Note that vertex 2 is .4142 outboard of the centre of the bildge radius. Set the snap value to .4142 and move vertex 1 inboard one snap and vertex 4 upwards one snap.

63

Tutorials

Vertex 4

Vertex 2 Vertex 3 Vertex 1

Vertex 0

Figure 2-6: Matching the Midship Curve to the template Note: Visualize straight-line segments between the vertices. The curve generated is tangent to these straight line segments and contacts the halfway point of the segment. The fillet operation creates an exact circular arc while the matching operation creates a parabolic approximation.

2.4 Generating the Forebody Surface

This exercise introduces the extrusion surface type. The extrusion method creates a surface by advancing a given curve along a straight path, thus sweeping out the surface. We will extrude the midship curve to create a surface that will become the forward part of the hull. To create the surface: 1. Click the Create Mode button. 2. Click the Create Surface button. 3. In the Create Surface dialogue box, select the Extrude tab, type the following information, and click OK:
64

Tutorial 2 Field
Surface Name Curve Vector Col Mesh

Entry
Foreship Midship Curve L=F120 (the entire forebody length from midship) Number = 3, Max Degree = 2

Note: This creates a surface with three columns, as specified, and six rows copied from the six vertices on Midship Curve. (See Figure 2-7.) 4. Click the Para view button. Rotate the view with the scroll bars at the right and bottom to get a good look at the surface. 5. Click the Edit Mode button.

Figure 2-7: The Foreship Surface

To close the Forward End (i.e. start to form the bow):

65

Tutorials 1. Ensure you are working with columns by clicking the Rows/Columns button, if necessary - rows appear as horizontal lines and columns as vertical lines. 2. Select the column at the forward end (furthest from the circle template): click its top control point. The readout at the left of the screen should display Row 5, Col 2. 3. Click the Isolate button to isolate only the forward-most column. 4. Click the Front view button. 5. Reposition the top control point (verterx 5) of the forwardmost column at the centreline by typing 0 in the T coordinate box in the coordinate boxes at the top left of the screen, and then hitting Enter. (See Figure 2-8.)
Vertex 5

Figure 2-8: Top vertex moved to centreline 8. With the topmost vertex selected, click the Straighten button and then click on the vertex at the baseline/centreline. This will move all the vertices in between the two vertices you selected to the centreline. (See Figure 2-9.)

66

Tutorial 2

Forward column

Figure 2-9: Forward column straightened 9. Click the Top view button to see the effect. (See Figure 2-10.)

Figure 2-10: Top view To form the Stem: 1. Click the S Side view button. (Make sure Foreship is still selected and you are in Edit Mode.)
67

Tutorials 2. Click the Control/Edit Points button to switch to Edit Point mode. 3. Zoom in on the forward end of Foreship. 4. Select the bottom vertex. Then, watch the Row display at the bottom of the screen and press the F4 key repeatedly to switch to the next vertex up the column. Note the position of each vertex, as several are in the same position. Press the F3 key to switch to the next vertex down the column. 5. Move the edit points longitudinally and vertically until you get the desired bow profile. You can drag the vertices with the mouse, or move them with the arrow keys on the keyboard. You may have to reduce the Snap value to have the vertex move by a small enough distance. Remember to press Enter after positioning each vertex. (See Figure 2-11.)

Figure 2-11: Side view 6. Ensure that the bottom of the bulb fairs smoothly into the flat bottom by switching to Control Point Mode and positioning the Row 0 and Row 1 vertices at V = 0. 7. Change back to displaying all columns by clicking the Isolate button.
68

Tutorial 2 8. Select File - Save and save your work so far.

2.5 Controlling Bow Rounding

In this exercise, we will round out the bow (in plan view) by adding another column of vertices and then use this column in conjunction with the column at the centreline to form the bow radius and also to ensure tangency across the centreline. To add a new column to the Stem: 1. Select the middle column (Col 1) by clicking on one of its vertices. (To do this, Foreship must be selected and you must be in Edit Mode with Isolate off.) 2. Click the Add Row or Column button. (Make sure you are working with columns, not rows.) Note: The Add Row/Column button is not activated when a vertex at the ending edge of a surface is selected (i.e. row 5.) You must be on any other vertex in the column to have the Add Row/Column button activated. 3. In the Insert dialogue box, select Proportional Interpolation and specify a proportion of 1 and click OK. (This places the control points of the new column at the same location as those of the next column - the column at centreline. You can see this by toggling between Control Point Mode and Edit Point Mode.) (See Figure 2-12.)

69

Tutorials

New column

Figure 2-12: New column added 4. With column 2 selected, click the Lock button. 5. In the Surface CP Locking dialogue box, select Relative to Next, check the Longitudinal and Vertical check boxes and click OK. Note that the vertices change to purple to indicate that they are locked - none of these vertices can be moved longitudinally or vertically - only transversely. Note: At its edges, a surface is tangent to the straight line drawn between the edge control point and the next point inside the surface. Having the vertices on the new column exactly outboard of the vertices on the centreline column forces the forward edge of the surface to meet the centreline at 90 degrees when viewed from above. To form the shape: 1. Click the 4 View button and then in the Front view window. 2. Switch to Edit Points Mode. 3. Click the Surface Mesh button. 4. Working only on the new column in the Front view, move the vertices away from the centreline to create the necessary rounding. Remember that these points are on the surface. Tangency is ensured across the bow because these points can only be moved transversely. See Figure 2-13.
70

Tutorial 2 5. Switch to Select mode to better see the result.

Figure 2-13: Creating bow rounding

2.6 Controlling Shape and Fairness

This exercise examines some of the functions and tools used for fairing. To fair the shape of Foreship: 1. Turn off Surface Mesh. 2. Switch to Edit mode. 3. Select the column ahead of the midship column (Col 1). 4. Click the Add Row or Column button. 5. In the Insert dialogue box that appears, select Proportional Interpolation and specify a proportion of 0.75. Click OK. 6. Select Settings - Contours. To help visualize the surface, we will now set some stations, waterlines and buttocks. 7. In the Contours dialogue box: Set stations as follows: check that Location of Sta.0 is set to 0 (midship) and Station Spacing is set at 1m. Click the Stations radio button, click Group, set Last to 120F, Step to
71

Tutorials 10 and click OK. This will create a group of stations from 120F to 0 at every 10m. Set buttocks: Click the Buttocks radio button, click the Group button, and set First to 0, Last to 12, and Step to 1, and then click OK. This creates buttocks from 0 to 12s at every metre. Set Waterlines at 0 to 12 at a Step of 1. When you are done, click OK. 8. Click the Contours button to make all contours visible. You can see all contours in all views by checking the setting Setting Preferences Display Contours in All Views. 9. In Front, S Side and Top views, fair the shape by modifying the control (or edit) points on the column you just inserted until you achieve the forward shape that you want. Tip: To maintain what will be the flat of side, do not move the vertices of columns 0 or 1 transversely or vertically.

Autoships fairing tools consist of the Porcupine Plot, the Curvature Window and Gaussian, Mean and Absolute Curvature. To get a porcupine plot, when viewing Edit points, click the Curvature/Normals button on the Display toolbar. It is best to use this feature with the Isolate button on. The porcupine plot displays the curvature of the row or column as a series of spines radiating from the row or column. The length of the spine indicates the relative curvature along the row or column. Note the setting Settings Invert Curvature Display which plots the spines as 1/curvature, thus showing the relative straightness along the row or column. The Curvature window is turned on and off from the View Curvature Window menu option. It plots the relative curvature along the row or column as a function of

72

Tutorial 2 row/column length. Vertex positions are shown as vertical tick marks. This window can be re-sized and moved. Gaussian Curvature, Mean Curvature and Absoloute Curvature are found under the View menu. A rendered image will appear in the Para view window. These options display the curvature as a color plot. Mean curvature shows the average of row curvature and column curvature and is best used for seeing the relative curvature across the surface. Gaussian Curvature is the product of row curvature and column curvature and is good for an indication of buildability the more white (flat or single curvature) appearing, the easier the surface is to construct. Note the setting Settings Preferences Curvature Display Color Compression Index which sets the scaling factor for curvature-to-visible-spectrum for the color plot. Refer to the on-line help for details about using these fairing tools. 9. To see the results of your work, click the Para view button and rotate to the desired view. Then Select View - Render to render the surface. (See Figure 2-14.)

Figure 2-14: Rendered view of the hull

73

Tutorials

2.7 Controlling Flat-of-Side

A flat-of-side for the foreship section is most easily accomplished with the aftmost three columns. In our model, Column 0 is located at midship, column 1 will become a knuckle line and so define the forward end of the flat-of-side, and column 2, further forward, will be used to ensure the curved side blends smoothly into the flat side. If the rows of control points passing through these three columns are always in a straight line then the surface will be tangent and fair at the knuckle column. To control Flat-of-Side: 1. Click View - Render to return to normal view, if necessary. 2. Click the S Side button. 3. Select the Foreship surface and switch to Edit Mode by double-clicking on the outline of surface Foreship. 4. Ensure that you are in Column mode and turn off Isolate, if necessary. 5. Select Column 1 and click the Toggle Corner button. 6. In Top and Side views, move the vertices longitudinally (but not transversely or vertically) until they are at the correct location to define the forward end, or tangency, of the flat-ofside. Do not worry about getting the locations exact you can move them again later. (See figure 2-15).

74

Tutorial 2

Column 1

Figure 2-15: Editing Column 1 to define the Flat of-Side. Note: To ensure the vertices move longitudinally only, use the arrow keys on the keyboard or turn on Ortho and drag the vertices. When using Ortho, also use Snap or Grid. Now we will add another column ahead of the knuckle column to ensure tangency across the knuckle column: 1. With Column 1 selected, click the Add button. 2. Specify a proportion of 0 and click OK. Remember, Add is not accessible if the end vertex of the column is selected. 3. Select the top vertex of column 2 and click the Isolate button. (This vertex is suprimposed on the top vertex of column 1. When you click on superimposed vertices, the one with the lowest number is selected. You may have to use the F3, F4 and F5, F6 keys to select the correct one.) 4. We are going to drag this entire column forward. To be sure we wont move it up or down, toggle on Ortho. 5. In Side view, drag the entire column forward by pointing at the top vertex in column 2 and, while holding the left mouse button down, move the cursor some distance forward, then hold down the Shift key and release the mouse button.
75

Tutorials Note: To ensure flatness and tangency, the rows of control points passing through column 0, 1 and 2 must form a straight line. This is easiest to arrange by making the rows run purely longitudinal - no change in T or V - in this region. 6. In Side, Top and Front view, arrange the points of column 2 and 3 to fair in the forward sections. Remember to not move column 2 vertices transversely or vertically. (Figure 2-16.)

Figure 2-16: Fairing the forward sections

2.8 Generating the Aftbody Shape

You could generate the aft body as you did the foreship. However, we suggest another method: a lofted surface. A lofted surface is generated from a set of curves by linking like-numbered parameter values on the curves. We will create the aft hull shape by lofting a surface between two curves: the midship curve and one we will create to describe the aft profile. Later, well add more columns to fill and form the shape. Creating an aft profile curve: 1. Click the Create Mode button.

76

Tutorial 2 2. Click the Create Curve button. 3. In the Create Curve dialogue box, select the Free tab, type the following and click OK: Field
Curve Name Parameters End 1 End 2 Colour

Entry
Stern Curve Control Points = 8; Max Degree = 2 the centreline-baseline at the aft end of the vessel (L=100A, T=0, V=0) the top of the transom at centreline (L=120A, T=0, V=U18) Yellow

5. Click the S Side button, go to Edit mode and click Grid. 6. Zoom in on the curve: click the zoom button, point above and to the left of the top of the curve, hold the mouse button down and drag a zoom box diagonally to below and to the right of the bottom of the curve and then release the button. 7. Drag the control points to form the aft profile. For tangency along the centreline, position vertex 1 at V=0. Be careful to not move the topmost or bottom-most points. Refer to Figure 2-17. 8. In Front view (or Back view) move vertices six and seven outboard to form the transom. Refer to Figure 2-17. Note: To form the shape easier, you may want to toggle the vertex at the bottom of the transom (vertex 5) to a corner.

77

Tutorials

Figure 2-17: Creating the Stern Curve To create the Aft Hull Surface: 1. Click the Create Mode button. 2. Click the Create Surface button. 3. In the Create Surface dialogue, name the surface Aftship and select the Loft tab. 4. Under Method, select the True Loft radial button. 5. In the Available Curves list box, click Midship Curve and then the Add button, and then Stern Curve and Add again. 6. Click OK. The Aftship surface has only two columns - the forward edge at Midship curve and the aft edge at Stern curve. Consequently, the highest that row Max Degree can be is 1 (maximum = the number of columns minus 1), so there is no curvature in the longitudinal direction. Also, these two columns are shaped the same as the curves they were derived from but are not connected to the curves in any way. To keep the shape of the columns the same as the curves, we must not move any of the vertices of these columns.

78

Tutorial 2 Note: If you set vertex 5 to be a corner then Aftship has a knuckle row (the diagonal line) corresponding to the corner. To add additional columns to the Aft Hull Surface: 1. Click the Edit Mode button. 2. In the S Side view, select the column at the forward end of the Aftship surface and click the Add button. (Make sure you are in Column mode, not Row mode and do not have the top vertex selected.) 3. Specify a proportion of 0 and Click OK to create another column at the same position as the forward column. 4. Click the Isolate button to work on the new column (Col 1) without interference from the column that was copied. (Check that Col 1 is selected.) 5. Select the top vertex and pull it straight aft to roughly where you want the flat-of-side to end and then hold down the Shift key and release the mouse button. Be careful to not move the vertex vertically: watch the cursor coordinates and compare the cursors vertical value to the vertexs vertical coordinate. The job will be easier if you turn on Ortho. 6. Click the Corner button to turn column 1 into a knuckle. This makes column 1 become the end of the flat of side. 7. In both S Side view and Top view, modify column 1 to form the aft end of the flat-of-side. Remember to move the vertices longitudinally only. 8. With Column 1 selected in Edit mode, click the Add button. 9. Specify a proportion of 0 and click OK. 10. Move the Column 2 vertices directly aft to ensure tangency at the flat of side. Dont move them transversly or vertically. In Top view the surface appears as straight lines (not curved). This is because the Row Max Degree is only 1. Well attend to that now. 11. Select Edit - Attributes.
79

Tutorials 12. In the Attributes dialogue box, set CDeg for Aftship to 3 and CRes to 20. Also, set RRes to 60 to allow better display of the surface shape. Click OK. 13. To help in fairing, go to Settings - Contours and add another group of stations from 0 to 120a at Step 10. 14. Turn on the contours by clicking on the Contours button. (See Figure 2-18.) The goal in fairing a surface is to get the rows and columns to flow as smooth lines. Start with the Control Points to be sure the basic mesh is smooth, then progress to smoothing out the Edit Points. Fine tune the vertex positions by looking at the Mean Curvature. If necessary, add another column or two ahead of the aftmost column to aid in fairing. You can also add more rows, however be aware that you might adversely affect the shape at midship.

Figure 2-18: Aftship Surface Because of the knuckle in the Stern Curve, the surface Aftship was created with a knuckle row. You may find it easier to fair the Aftship surface if you turn the knuckle row (Row 7) into a non-knuckle: select the row and click the Toggle Corner button. However, if you turn the knuckle off, you will notice the aft edge of the surface no longer follows the Stern Curve. The easy solution is to fair the surface and then turn the row into a knucle line again. You should
80

Tutorial 2 then make sure that the knuckle line is not causing an unwanted chine by positioning the knuckle vertex on a straight line between its neighbours. To do this, straighten the portion of the column which includes the two vertices on either side of the knuckle vertex: in column mode, click on the vertex below the knuckle vertex, then click the Straighten button and then on the vertex above the knuckle vertex. You should repeat the straightening operation in one other view to make sure the knuckle vertex lies on a straight line between its neighbours. (See figure 2-19.)

Knuckle vertex Straighten this section

Figure 2-19: Straightening across the knuckle line

2.9 Adding a Bow Thruster

This exercise demonstrates how to project a curve onto a surface and shows one possible use for a projected curve. We will create two curves a template curve and its projection onto the hull and then rule a surface between them to create the thruster. To create the template curve: 1. Click the Create Mode button and the Create Curve button. 2. Select the Arc tab, enter the following and click OK.

81

Tutorials Field
Curve Name Plane Centre Angles Semi Axes

Entry
Circle Side On the centreline, at an appropriate position for the bowthruster (we used: 108F, 0T and 3U) Start: 0; End: 360 Circular: Checked Radius: An appropriate radius, we used: 1.1 m

3. Change to S Side view and zoom in on the area around the forward part of Foreship. (See Figure 2-20.)

Figure 2-20: Circle curve If you would like to re-position the curve, do the following 1. ensure that the Circle curve is selected and click the Set Base Point button. 2. Click near the centre of the Circle curve. This will move the base point from 0,0,0 to the location just clicked on. 3. Click the Move button. 4. When you move the cursor into the view, you will see a rubber band originating from the curves base point.
82

Tutorial 2 Position the bilge circle at the new location and click the left mouse button. Note that the base point has moved also. Note: We moved the base point first to avoid confusion: because the rubber band originates from the base point and the base point was at the origin, then the base point would not have appeared in the current zoom, so the rubber band would have started from somewhere off the screen. The rubber band indicates the relative displacement of the curve the curve will move by this amount from its current location, not to the position indicated by the cursor. To project the Circle curve onto the hull surface: Projecting the Circle curve onto the hull surface produces a new curve that is embedded on the hull. An embedded curve will adapt itself to any changes in the host surface. 1. Switch to Para view. 2. In Create Mode, click the Create Curve button. 3. Select the Projected tab, enter the following and click OK: Field
Curve Name Projection Type Source Curve Host Acceptable Tolerance Colour

Entry
Thruster Curve Side Type 2 Circle Foreship 0.001 Light Blue

4. Zoom in on the forward end of the hull to see the result.

83

Tutorials Note: A type 1 projected curve is non-editable and can be altered only by editing the source curve. A type 2 projected curve is a separate, editable curve that is embedded on the surface. Either type can be updated to adapt to changes of the source curve by selecting the curve and clicking on Edit Regenerate Object.

Thruster Curve

Circle

Figure 2-21: Circle projected onto Foreship Surface Use Thruster Curve to cut the thruster opening in the hull: 1. Select the Foreship surface. 2. Click the Trim button. In the Trim Surface Foreship dialogue box, pick Thruster Curve and click OK. The program will show various trim options and prompt you with Keep this domain. Answer No to the option not wanted, and Yes to the option wanted. 4. Select Foreship and View - Render. (See Figure 2-22.)

84

Tutorial 2

Figure 2-22: Rendered trimmed Foreship surface To create the Tunnel as a Ruled Surface: 1. Turn off Render by selecting View - Render again. 2. In Create mode, click the Create Surface button. 3. Select the Rule tab. 4. In the Create Surface dialogue, type the following and click OK: Field
Surface Name Curves

Entry
Thruster Circle; Thruster Curve

5. Select View - Render to see the result. Note: If the surface Thruster appears as a tie, or hourglass, then you must change the direction of one of the curves and regenerate the surface. The direction of a curve is shown by a small arrow near the beginning of the curve when in Select mode. The arrows on both curves should point the same direction. To change the direction of a curve, select the
85

Tutorials curve, then in Edit mode click the Reverse Ends button. Then update the Thruster surface by selecting it and clicking on Edit Regenerate Object. Note that if you reverse the embedded curve used to trim the surface, you will have to re-do the trim operation. 6. In Select mode, select both the new Thruster surface and the Foreship surface. (Select one, and then while holding down the Shift key, select the other you must click on the outline of the surface.) Note that the object box at the top of the screen displays Multiple Select. 7. Select Arrange - Group. 8. In the New Group dialogue, change the name to Hull Fwd and click OK. Note the Make Comps Invisible checkbox. If checked, the visibility of the two surfaces will be turned off in the Attributes dialogue. 9. If it is not selected, select the new group Hull Fwd and select View-Render to see the result. (See Figure 2-23.)

Figure 2-23: Rendered Hull Fwd group

86

Tutorial 2

2.10 Adding a forward deck with Camber and Sheer

This exercise introduces the camber curve type, the sweep surface type and trimming one surface to another. Autoship can create parabolic camber curves, or you can design your own camber curve. In this exercise, we will use a parabolic curve. In its simplest form, a sweep surface advances one curve (the pattern curve) along another curve (the guide curve), thus sweeping out a surface. We will sweep a camber curve along a sheer at centreline curve to create the forward deck, obtain the intersection with the hull and then trim the deck at that intersection. 1. Turn off render by clicking on View Render, switch to Para view and click the Zoom Extents button. To create the parabolic Camber Curve (the pattern curve): 1. Click the Create Mode button and the Create Curve button. 2. Click the Camber tab. 3. Enter the following and click OK: Field
Curve Name Projection Dimensions

Entry
Deck Camber Front Half : radio button selected Breadth A value slightly larger than the vessels half-breadth, we used 14.1m Height: For a 1:50 camber, use .28

Colour

Bright Green

Look closely under the midship curve to see the Deck Camber curve it starts at 0,0,0.

87

Tutorials To create the sheer Curve (the guide curve): 1. Click the Create Mode button and the Create Curve button. 2. Click the Free tab. 3. Enter the following and click OK: Field
Curve Name Parameters End 1 End 2 Colour

Entry
Fwd Sheer at Centreline Control Points = 4; Max Degree = 3 L = 0, T = 0, V = U18 L = F120, T = 0, V =U18 Bright Green

4. If you wish to create some sheer in the deck, switch to Edit mode and S-Side view and move the aft three vertices downwards to form a smooth curve. To create the deck surface: 1. Click the Create Mode and Create Surface. 2. Click the Sweep tab. 3. Enter the following and click OK: Field
Surface Name Pattern Curves Guide Curves Options Foredeck In the upper box, pick Deck Camber In the upper box, pick Fwd Sheer at Centreline Parallel: Checked

Entry

Note: Parallel will maintain the original upright orientation of the camber curve as it sweeps out the surface, just as deck beams would be placed. If Parallel was not checked, the
88

Tutorial 2 relationship between the two curves would be maintained, thus, in order to keep perpendicular to the guide curve as the guide curve bends due to sheer, the pattern curve would rotate (in side view) as it was swept along the guide curve. 4. View the surface in 4-view to see the camber and sheer. It may help to turn on the Mesh. (See figure 2-24.)

Figure 2-24: The Foredeck surface To trim the deck surface: 1. Select Foredeck and Foreship. Note: If the Make Comps Invisible checkbox was checked when you created the group HullFwd, the visibility of the Foreship surface will be turned off so you will not be able to select it from the main screen. To turn on its visibility, go to the Attributes dialogue and check the Vis. column for the surface Foreship. 2. Click the Surf-Surf Intersect button. (If the button is greyed out, see Note above.) In the Surf-Surf Intersect dialogue box, make sure the two surfaces shown are Foredeck and Foreship, set the tolerance to 0.005m, set the colours of the curves to purple and click OK.
89

Tutorials This will create two curves which describe the intersection of the Foreship and Foredeck; one curve, Foreship Int1, is embedded on the Foreship surface, the other curve, Foredeck Int1, is embedded on the Foredeck surface. To avoid future confusion, we suggest you rename the curves using the following convention: rename SurfA Int1 to SurfB-SurfA, and SurfB Int1 to SurfA-SurfB, where the first name indicates the surface the curve is embedded on, the - is reserved to indicate an intersection curve, and the second-named surface is the surface intersected with. 3. Rename curve Foreship Int1 to Foredeck-Foreship: click Edit Attributes, click on the name Foreship Int1 and then click the Properties button. In the Curve Properties dialogue, under Name, type Foredeck-Foreship and click OK. 4. Similarly, rename Foredeck Int1 to Foreship-Foredeck. 5. Select the surface Foredeck. 6. Click the Trim Surface button. 7. In the Trim Surface Foredeck dialogue, select the curve Foredeck-Foreship and click OK. Answer Yes at the appropriate trim option and No to the others. 8. Select the surface Foreship. 9. Click the Trim Surface button. 10. In the Trim Foreship Surface dialogue, select both of the curves Foreship-Foredeck and Foreship-Thruster Curve and click OK. Answer Yes at the appropriate trim option shown and No to the others. (See figure 2-25.)

90

Tutorial 2

Figure 2-25: Trimmed Foreship and Foredeck

2.11 Adding an Aft Deck with Camber and Sheer

Use the same procedure to create the surface Aftdeck. In our example, we kept the Aft Sheer at Centreline curve horizontal.

2.12 Creating a group of the entire vessel

To create the group: 1. Select one of the surfaces you have created. 2. Click the Arrange Group menu option. 3. In the New Group dialogue, type the name Main and click OK. 4. With the group Main selected, click on the button now marked Group in the upper right-of-centre of the screen to open the Group Editor dialogue. 5. In the Group Editor dialogue, under Objects - Select, click the Surface radio button.

91

Tutorials 6. In the pick box directly below that, pick one of the other surfaces. 7. Click the Add button. The selected surface will be added to the object list. 8. Add the remaing three surfaces the same way. 9. Click in the Stbd + Port check box to have all the selected surfaces mirrored to the other side of the vessel. 10. Exit the Group Editor dialogue. 11. Switch to Para view and render the group. (See figure 226.)

Figure 2-26: Rendered group Main

92

Tutorial 2

2.13 Material Properties

In this section, we will work a little with material properties: 1. Select the group Main. 2. Click the Properties button (currently labelled Group at the top of the screen 3. In the Group Editor dialouge, in the list at left select the surface Aftdeck. 4. In the Material frame, click the Edit Material.. button. 5. In the Material dialogue, at the list at left pick Steel, under Effectiveness, pick Thin Shell, set Thick to 0.015 and click OK. 6. In the Material frame, click the Apply to All button. 7. Click OK. 8. With group Main selected, pick the Report Create Weights and Areas menu option. 9. Open the report window and view the results.

2.14 Summary
This completes the second tutorial. The first and second tutorials introduced various tools used for constructing a model, and described how to use the building blocks of the system objects by creating and using simple curves and surfaces. Tutorial three completes this introduction to hull design with Autoship. In tutorial three, hull design is accomplished using extrusion, mirroring surfaces, integrating panels, and by using ruled and swept surfaces.

93

Tutorials

94

Tutorial 3

Tutorial 3 - Asymmetric Hull Catamaran

3.0m

20m 3m Figure 3-1: Asymmetric Catamaran

12m

3.1 Introduction Asymmetric Hull Catamaran

In Tutorial 3 we show how to: Design the outboard half of the hull by extrusion Generate the inboard half of the hull by modifying a mirrored copy of the outboard half Design the tunnel as an integration of several panels Fit a deck between a centerline and a deck edge curve Construct a pilot house using a ruled and a swept surface

We have constructed this model as TUT3.PR3. You may want to review it before continuing.

95

Tutorials

3.2 Starting Out

To begin: 1. Select File - New. 2. Select Settings - Units. 3. In the Units dialogue, select Meters and Tonnes and click OK. 4. Select Settings - Preferences. 5. In the Preferences dialogue, click the Coordinate System button. 6. In the Coordinate System dialogue, click the Naval / Aircraft (US) radio button and click OK. 7. Click OK in the Preferences dialogue. 8. Click File Save As. 9. In the Save Project dialogue, save the project as TUT3 in the MYTUTS directory. 10. In the Project Info dialogue, type a description such as 20m Catamaran, and click OK.

3.3 Designing the Outboard Hull

The outboard half of the hull will be constructed by extruding a simple cross-section curve. To create the cross-section curve: 1. In Create Mode, click the Create Curve button. 2. In the Create Curve dialogue, type the following information, and click OK:

96

Tutorial 3 Field
Curve Name Tab Parameters End 1 End 2

Entry
Section Free Number = 4, Max. Degree = 2 L = 0; T = 1.6; V = 3 L = 0; T = 0; V = 0

3. Switch from Snap to Grid mode (value of 0.1) by clicking on the Snap button at the top left of the screen. Note: By using Grid instead of Snap, you can easily reposition vertices to rounded, or even value, co-ordinates. Snap causes the vertex to jump relative to its initial position. Grid jumps to an absolute position as defined by a grid with an interval equal to the Snap setting. 4. In Front view, add another vertex and use the Toggle Corner button to form a chine flat and then reposition the vertices to form the hull section at midship, as depicted in Figure 3-2.

Figure 3-2: Section Curve

97

Tutorials

3.4 (a) - Creating the Outboard Hull Surface

To create the outboard hull surface: 1. In Create Mode, select Create Surface. 2. In the Create Surface dialogue, type the following information, and click OK: Field
Name Tab Curve Vector Column Mesh

Entry
Hullout Extrude Section L: 20F Number: 4; MaxDegree: 3

3. Switch to Edit mode and Column mode, select the forward column, and then click the Isolate button. 4. In Front view, move the topmost vertex to the centreline: select vertex 0 click in the T cooridinate box at the top left of the screen, type 0 and hit Enter. 5. With the topmost vertex selected, click the Straighten button and then click on the lowest vertex to straighten all the vertices to the centerline. 6. In Side view, move the points longitudinally to give the desired bow profile. 7. In Side, Top and Front view, form the hull to achieve the shape you want for the outboard half of the hull. Try to set the top edge of the hull around midship at T = 1.6. We will be trimming off the top edge of the hull, so do not bother to shape it in profile. You should also position the forward-most vertices of both chines at the same location. (See Figure 33.) Note: We added another column forward to give us better control over the bow shape.
98

Tutorial 3

Figure 3-3: Outboard hull surface

3.4.(b) - Ensuring fairness at the forward-lower corner of the surface.

In Tutorial 2, special emphasis was placed on positioning the vertices at the forward end of the centreline curve to ensure that the stem below the chine blended smoothly into the stem above the chine. A similar situation exists on the surface Hullout at the corner where the forward edge meets the lower edge. Currently, this corner is at the aft end of the curved-forefoot. In order to make the forward edge transition smoothly into the bottom edge, we must position the corner vertex and its closest neighbouring vertices on the forward edge and bottom edge on a straight line. An easy method would be to position all three vertices at V = 0. However, we will outline a more general method. 1. With Hullout selected, in Edit mode, and Column mode, with Control Points selected, click on the vertex at the bottom column immediately aft of the stem column (Row 4, Col 3 in our model) and write down the L and V coordinates. (See figure 3-4.)

99

Tutorials 2. Click on the vertex at the bottom of the stem column (Row 4, Col 4 in our model) and write down the L coordinate. (See figure 3-4.) 3. Click on the next vertex above the bottom of the stem (Row 3, Col 4 in our model) and write down the L and V coordinates. (See figure 3-4.)

Row 3, Col 4

Row 4, Col 3

Row 4, Col 4

Figure 3-4: Control points at stem 4. Create a new curve using the Free tab. Set Control Pts to 3. For End 1, type in the first set of coordinates you wrote down. For End 2, type in the last set of coordinate you wrote down. 5. With the new curve selected, switch to Edit mode, and Edit Points, if necessary, and select the middle vertex. 6. Set the middle vertex to the L coordinate you wrote down for the corner of Hullout: click in the L coordinate box at the upper left of the screen to highlight the L value, type the new coordinate and hit Enter. 7. Straighten the entire curve: select one of the end vertices, click on the Straighten button and click on the vertex at the other end of the curve.

100

Tutorial 3 8. Copy the V coordinate of the middle vertex of the curve to the corner vertex of the Hullout surface: select the middle vertex, click in the V coordinate box, hold down the Ctrl key and press the C key (this copies the coordinate to the clipboard). Switch to Select mode, select the Hullout surface, switch to Edit mode and select the vertex at the corner where the forward edge meets the bottom edge (Row 4, Col 4). Click in the V coordinate box, hold down the Ctrl key and press the V key (this pastes the value from the clipboard) and hit Enter. 9. Go to the Attributes dialogue and turn off the visibility of the curve used for this straighten process. This effectively straightens the forward-lower corner of the surface Hullout. Note that if you move either of the three vertices used for the straightening operation, then you will have to re-do the straightening operation.

3.5 Generating the Inboard Hull Half

To have both sides of the hull match up properly at the centerline, we will copy the outboard half of the hull and then mirror it to create the inboard half, and then rework the inboard shape. To copy and mirror the outboard half of the hull: 1. In Select Mode, select Hullout. 2. Copy the outboard hull: hold down the Shift key and click the Clone (Shift Copy) button. 3. In the Copy dialogue, rename Copy of Hullout to Hullin and, click OK. 4. With Hullin selected, in Front view, click the Flip Horizontal button. 5. If both chines end at the same location at the stem, then in Edit mode and Row mode, select one of the knuckle lines (rows) and click the Delete Row or Column button to
101

Tutorials remove it. If you did not position the forward-most vertices of both chines at the same location, then you cannot delete either chine as it will change the profile of the stem. 6. To decrease the breadth of Hullin, use the scale function: In Select Mode, right-click the Scale button. Set the transverse scale to 0.875 and click OK. Tip: Before scaling Hullin, make sure that its Base Point is located at T = 0: with Hullin selected, in Select mode, rightclick on the Set Base Point button. Set the T value to 0, if it is not already. 7. Edit the shape as you see fit. Take care to not move any of the vertices at the centreline, otherwise the two halves of the hull will not match. (See Figure 3-5.) In order to have the same shape for the bow profile on Hullin as on Hullout, the distribution of vertices must be the same. This means the second vertex from the top must be a corner vertex and must not move from its original position. And since this vertex must be a corner vertex, then the entire row must be a knuckle row. If you do not want to have a chine at that row, then the columns must be straigtened across the corner vertices, as follows: 8. In Edit mode, switch to Column mode, click on the Isolate button and switch to Edit Points, if necessary. 9. Using the aftmost column as an example, in Front view, click on the vertex immediately above the chine vertex (the chine vertex is the green one), then click on the Straighten button, then click on the vertex immediately below the chine vertex. Repeat this straightening procedure in S Side view. 10. Repeat this procedure for the other columns. Straighening across the chine will effectively cause the chine to disappear. Note that if you edit the shape of the surface after straightening, you will have to re-do the straighten operation.

102

Tutorial 3

Figure 3-5: Mirrored inboard half of the hull

3.6 Designing a Tunnel and Fillet Panel

First, we will move the hull to its correct position. Next, we will create a tunnel by extruding a surface from a centerline curve. Then, we will construct a fillet panel between the tunnel and the inboard hull side using the Blend surface type.

3.6.(a) - Moving the Hull to its Correct Position

At this point, the hull centerline is at T = 0. It is to be moved to 4.0 starboard. 1. In Select mode, select both the surfaces Hullin and Hullout. 2. Right-click on the Move button. 3. In the Move dialogue, set the T value to 4 and click on OK. Now Hullin and Hullout are at centred at 4m to starboard while the boats centerline is at T=0.

103

Tutorials

3.6.(b) - Creating the Tunnel Surface

1. Create a new curve: Field
Curve Name Tab End 1 End 2

Entry
Tunnel Shape Free L=F20; T=0; V=U3.0 L=0; T=0; V=U1.9

2. Switch to S Side view and reshape the curve as indicated in figure 3-6.

Figure 3-6: Tunnel Shape curve

104

Tutorial 3 To create the surface Tunnel: 1. Create a new surface: (See Figure 3-7.) Field
Surface Name Tab Curve Vector

Entry
Tunnel Extrude Tunnel Shape L = 0; T = S4.0; V = 0

Figure 3-7:The Tunnel Surface,

To create a smooth corner between the Tunnel and Hullin, we will create a fillet panel using the Blend surface type. For this design, this fillet panel will have a 0.25m radius over most of its length but will taper to 0 at the forward end. Two surfaces to be blended must have congruent edges, such as at a chine or at a trimmed intersection. Therefore, to blend the Hullin and the Tunnel, we must first obtain the intersection of the Tunnel and Hullin surface and then trim the surfaces to the intersection.

105

Tutorials To obtain the intersection: 1. Switch to 4 View. 2. Select both the Tunnel and Hullin surfaces. 3. Click on the Surf-Surf Intersect button. 4. In the Surf-Surf dialogue, verify the surface names and click on OK. 5. In the Attributes dialogue, rename the curve Hullin Int1 to Tunnel-Hullin and Tunnel Int1 to Hullin-Tunnel. To trim the surfaces: 1. Select the Hullin surface 2. Click on the Trim Surface button. 3. In the Trim Surface Hullin dialogue, pick the curve HullinTunnel and click on OK. 4. Answer Yes to the appropriate Keep this Domain prompt and No to the rest. 5. Repeat steps 1 to 4 for the surface Tunnel. To create the fillet panel 1. Create a surface: Field
Surface Name Tab Surfaces Radii Variation

Entry
Fillet Blend Tunnel Hullin Cubic

106

Tutorial 3
Radii 1 = 0.25 2 = 0.25 3 = 0.25 4=0 Type Tolerance Fillet 0.001

2. The intersection of the two surfaces will be highlighted and you will be promted with Blend here? Answer Yes if the indicated path is correct. (See Figure 3-8.)

Figure 3-8: Fillet Panel A Blend surface operation creates one surface and two curves. The surface fits between the two curves, but is not joined to either of them. One of the curves is embedded on one surface and the other curve is embedded on the other surface. These curves can be used to trim the surfaces being filleted to the junction with the fillet panel. We will now re-trim the Tunnel surface at its junction with the Fillet and then re-trim the Hullin surface at its junction with the Fillet.

To re-trim the surfaces:

107

Tutorials 1. Select the Hullin surface. 2. Click on the Trim button. 3. In the Trim Surface Hullin dialogue, de-select the curve Hullin-Tunnel, select the curve Fillet 0 and click OK. (If you had selected the two surfaces in the reverse order when generating the Blend surface, then the curve embedded on Hullin would be named Fillet 1.) 4. Answer Yes to the appropriate Keep this Domain prompt and No to the rest. 5. Repeat this operation for the Tunnel surface. Note: If the surface trim does not seem to take effect, the likely cause is that the trimming curve is not closed. A closed curve means that either both ends of the curve contact an edge of the surface or the curve begins and ends the same location. If you encounter a case where the surface trim does not work, first check the location of each end of the trimming curve and, if necessary make adjustments to close the curve. 6. Save the project: click on File Save.

3.7 Adding an Upper Deck

The upper deck appears to be a relatively simple shape, however it has some complex restrictions. This surface will have three columns: an inboard one along the centreline, an outboard one along the surface Hullout, and a middle one exactly half way in between. To ensure tangency across the centreline, the vertices on the middle column must be positioned at the same height as the centreline column. To ensure proper control of the shape, the rows must be perfectly transverse. To ensure easy control of the shape, we must limit the number of rows to a manageable number, say five or six. We will employ a few tricks to accomplish this.

108

Tutorial 3 To create the Deck Edge curve: 1. Create a new curve: Field
Curve Name Tab Host End 1 End 2

Entry
Deck edge Embedded Surface radio button selected Hullout R = 0; c = 0 R = 0; c = 1

This will create a curve which runs diagonally across the surface. 2. In Edit mode, re-shape the curve to describe the deck edge. Make sure both ends of the curve contact an edge of the Hullout surface. (See Figure 3-9.)

Figure 3-9: Embedded curve on Hullout

To create a temporary curve: 1. Create a new curve by matching the Deck Edge:

109

Tutorials Field
Curve Name Tab Type Source Curve

Entry
Temp Match Free Deck Edge

Note: Copying an embedded curve produces another embedded curve. A Match curve does not have the restriction of being only embedded. 2. In S Side view, shape this curve to represent the profile of the deck centreline. Do not move the vertices longitudinally or transversely. You might find it advantageous to use the Porcupine plot to see the curvature: click on the Curvature button. Since this curve is so flat, try inverting the curvature by clicking on Setings Invert Curvature Display. This displays the relative straightness, rather than the relative curvature. (See Figure 3-10.)

Figure 3-10: The Temp curve

To create a Centreline curve:

110

Tutorial 3 1. Create a new curve by copying the Temp curve: with Temp selected, hold down the Shift key and click on the Clone (Shift Copy) button. In the Copy dialogue, name the new curve Centreline. 2. Move the entire curve to the centreline: with Centreline selected, click on the Scale button and for the T value type 0 and then hit Enter. You may wish to view the result by switching to Top view or 4 View. To create the Deck: 1. Create a new surface: Field
Name Tab Curves Column Mesh

Entry
Deck Rule Centerline Temp Number: 3 Max Degree: 2

2. Attach the outboard edge to the curve Deck Edge: switch to Edit mode, select the outboard column (Col 2), click on the Attach button and in the Attach Surface dialogue, under Action click on Attach to Curve and under Attach To select Deck Edge and then click on OK. (See figure 3-11.)

111

Tutorials

Figure 3-11: Deck Surface To clean up: 1. Detach the outboard edge of the deck: with Col 2 selected, click on the Detach button. 2. Delete the curve Temp: select the curve Temp, and click on the Delete button. 3. Trim the Hullout surface off at the Deck Edge curve: select the surface Hullout, click on the Trim Surface button, in the Trim Suface Hullout dialogue select the curve Deck Edge and click on OK. Answer Yes to the appropriate Keep This Domain prompt and No to the others. Notes: The shortcut to positioning the middle column exactly halfway between the edges is to hve the program insert it. The trick to setting the vertices on the middle column to the same height as the centreline column is to start with a surface in which the rows are transverse and horizontal. The best way to set up a surface in which the rows are transverse is to create a ruled surface between two curves that have the same number of vertices placed in identical longitudinal positions. The best way to obtain two curves with the same
112

Tutorial 3 number of vertices placed in identical longitudinal positions is to copy one to create the other. Because the Deck Edge curve is attached, a ruled surface generated from it would have hundreds of rows. A ruled surface generated from two free curves usually has only five or six rows. Often, attaching the edge of a surface to a curve disrupts the arrangement of the vertices on the edge being attached. Because the Deck surface was generated from a copy of the Deck Edge curve, attach the edge of Deck to Deck Edge did not distrupt the arrangement of the edge vertices.

3.8 Adding a Pilot House

We will create the house front and sides by ruling a surface between a curve embedded on the deck and a free curve some distance above the deck. The top will be created as a swept surface. To create the Housefront surface: 1. In Top view, create a new curve Field
Curve Name Tab Host Parameters End 1 End 2

Entry
Housebot Embedded Surface radio button selected Deck Number: 4; Max. Degree: 2 r = 0; c = 0 r = 1; c = 1

2. Modify this curve to represent the lower edge of your pilot house. (See figure 3-12.) To ensure tangency across the centreline, keep vertex 2 at the same longitudinal position as vertex 3 (the centreline vertex.)
113

Tutorials 3. Create another curve, Housetop Brow, as a free curve with 4 Control Pts and MaxDegree 2. Tip: for easy editing, set End 2 to a different L value than End 1. 4. In Top and S Side view, form Housetop Brow as the upper edge of the house side. (See Figure 3-12.)
Housetop Brow curve

Housebot curve

Figure 3-12: Housebot and Housetop Brow curves 5. Create the surface Housefront: (See Figure 3-16.) Field
Surface Name Tab Curves

Entry
Housefront Rule Housetop Brow Housebot

114

Tutorial 3

Figure 3-16: Housefront surface

115

Tutorials To create the Housetop surface: First, we will copy the Housetop Brow curve and reshape it to form the profile of the house top at the centreline. Next, we will create a new curve which describes the shape of the house top at the aft end. Finally, we will sweep this second curve between the Housebrow curve and the curve at centreline to produce the house top surface. 1. Copy the Housetop Brow curve: select Housetop Brow, hold down the Shift key and click on the Clone (Shift Copy) button. In the Copy dialogue, name the new curve Housetop Centre. 2. Set Housetop Centre to the centreline: right-click on the Scale button. In the Scale dialogue, set T to 0 and click on OK. 3. In S Side view, edit the heights of the vertices to form the profile at centreline. Do not move vertex 3, and try not to move the vertices longitudinally. 4. Switch to Front view. 5. Click on the Create mode button and then the Draw Curve button. 6. Click once at the aft end of the curve Housetop Centre. 7. Click at a position just above and inboard of the aft end of the curve Housetop Brow. Try to click at the same height as the where you clicked on Housetop Centre. 8. Click on the aft end of the curve Housetop Brow. 9. Right-click anywhere in the view window. 10. In the Curve Parameters dialogue, name the curve Housetop Shape, set Maximum Degree to 2, click on the Control Points radio button and click on OK. 11. If necessary, switch to Edit mode and modify the shape. (See figure 3-14.)
116

Tutorial 3

Housetop Shape curve

Figure 3-14: Housetop Shape Curve 12. Create a new surface: (See Figure 3-15.) Field
Surface Name Tab Pattern Curves Guide Curves Options

Entry
Housetop Sweep Housetop Shape Housetop Centre Housetop Brow Scaled: checked

117

Tutorials

Figure 3-15: Housetop surface

3.9 Starboard and Port Side

We will complete the catamaran by creating a group, Main, which contains all the surfaces we have created, and then set the group to mirror the assembly. 1. Create a group, Main, of the seven surfaces Hullout, Hullin, Tunnel, Fillet, Deck, Housefront, and Housetop: in Select mode, select as many of the surfaces as you can, then click on Arrange Group, in the New Group dialogue, set the name to Main and click OK. 2. With Main selected, click Edit-Attributes. 3. In the Attributes dialogue box, click the Group Editor button. 4. In the Group Editor dialogue box, include the remaining surfaces in the group: click on the Surface radio button, then select one of the remaining surfaces from the pick box, then click on the Add button. Repeat for the remaining surfaces. 5. Click on the Stbd + Port check box and click on OK. 6. Click on OK at the Attributes dialogue.
118

Tutorial 3 7. Save the project: click on File Save. 8. Render the group. (See Figure 3-16.)

Figure 3-16: Rendered catamaran

3.10 Summary
In Tutorials 1 to 3, you have been shown a number of ways to create and edit ships and boats. These tutorials are intended to be an introduction to Autoship. They do not describe the definitive methods for producing hulls. Using what you have learned in these tutorials, you should experiment with the program to develop the best methods for working with your particular type of vessel.

119

Tutorials

120

Tutorial 4

Tutorial 4 - Pocket Cruiser

4.75ft

5ft 24ft Figure 4-1: Pocket cruiser

4.1 Introduction Pocket Cruiser

In Tutorial 4, what we will design is a small, heavy displacement cruising yacht. This tutorial goes beyond the basic hull lines and completes the superstructure as well. The shell is built up much as a real boat would be constructed. First the hull is created, and then the transom, keel, deck, and cabin are added. You can add the mast, rigging, and sails later, but they are not included as part of this tutorial. The model we have constructed, TUT4.PR3, has these dimensions: Displacement: 4.0LT LOA: 24ft Beam: 9.5ft We suggest that you examine TUT4.PR3 before reading further.

121

Tutorials

4.2 Starting Out

To begin: 1. Select File - New. 2. Select Settings - Units and set the units to Feet and Pounds. 3. Select Settings - Preferences. 4. Click the Coordinate System button. 5. Click the Naval /Aircraft (US) radio button. 6. Click OK in the Coordinate System dialogue and click OK again in the Preferences dialogue. 7. Click on File Save As. Click OK. In the Save Project dialogue, type TUT4.PR3, and specify the MYTUTS directory to store this project in. In the Project Info dialogue field, type a descriptive message for the project and click on OK.

4.3 Creating the Hull

1. Create a new surface: Field
Name Tab Size Column Mesh Row Mesh

Entry
Hull Dimensions L = 24, T = 4.25, V = 5 Number: 4; MaxDegree: 3 Number: 4; MaxDegree: 2

Note: The number of rows and columns is based on previous experience. However, since you can easily add or delete rows or columns, you can start with fewer if you wish.

122

Tutorial 4

4.4 Shaping the Hull

To shape the bow: 1. Hold down the Shift key and click on the Zoom Extents button to zoom out in all four views. 2. With Hull selected, switch to Edit Mode and change to Column mode if necessary. 3. Select the top vertex on the bow column (Col 0), and click the Isolate button. 4. Set this vertex to the centreline: type 0 in the T coordinate box, and click Enter. 5. In Front view, straighten the whole column to the centreline: with the top vertex selected, click on the Straighten button and then click on the lowest vertex. 6. In S Side view, shape the bow profile by editing column 0 by eye. Its best to work with the control points. (See figure 4-2.) Tip: It is easiest to edit the shape of a row or column with Isolate on, but you may find it beneficial to toggle between Isolate and non-Isolate during the next few steps.

Figure 4-2: Editing the Bow Profile Note: in order to avoid a knuckle at the bottom of the stem in profile view, the vertices of Col 0/Row 1, Col 0/Row 0 and
123

Tutorials Col 1/Row 0 should all lie on a straight line. You can position them fairly close by eye, or draw a free, straight curve to use as a template, or use a hand calculator to find the exact position of one vertex based upon the postions of the other two. Refer to Tutorials 2 nd 3 for a further explanation. 7. Change to Rows, select Row 0 and form the fairbody shape. 8. Switch to Top view and shape the sheer line (Row 3, in our model.) 9. Switch to S Side view and shape Row 3 to get a pleasing sheer line. Experiment with using the Planar button to force the sheer into a plane: select the vertex on either Column 1 or 2 and click on the Planar button. The Planar routine calculates a plane based upon the positions of the two end vertices and the currently selected vertex and then adjusts the heights of the remaining surfaceedge vertices to lie on that plane. 10. Switch to Front view and re-shape column 3 to form the aft end of the hull. In steps 7, 8 and 9, you positioned the bottom and top vertices in profile, so you should not move them now. Note: we will be adding a transom as a separate surface, so the hull must extend aft of where the transom corner will be. Do not worry about the profile at the aft end of the hull. 11. Also in Front view, re-shape columns 1 and 2 to form the shape in the mid-body. (See figure 4-3.)

124

Tutorial 4

Figure 4-3: The Hull Surface

4.5 Instant Hydrostatics

4.5(a) Group
At this point, it is time to think about displacement. We will use the instant hydrostatics feature. This routine works only on a group, so we must create a group. To create a group: 1. With the Hull surface selected, in Select mode, click on the Arrange Group menu item. Rename the group to Main, un-check the Make Comps Invisible check box and click on OK.

4.5.(b) - Running Instant Hydrostatics

1. Click on the small H button near the lower left of the view window to open the Instant Hydrostatics window. 2. In the Instant Hydrostatics window, click on the Group button. 3. In the Choose Hydrostatics Group dialogue, select Main from the pick list and click on OK.
125

Tutorials 4. In the Instant Hydrostatics window, note the Depth display in the lower left corner. 5. Click on the Update button. Note: If the Invalid Parameters message appears, the likely cause is that the hull is not actually sitting in the water at the specified Depth. Set the Depth to a higher value and click on Update again. We are aiming for 4.0 LT displacement. It is not very likely that the displacement at the draft you have set is exactly 4.0 LT, however we can get Autoship to find the draft corresponding to 4.0 LT. 6. Near the bottom centre of the Instant Hydrostatics window, set the Mass to 4.0 and click on the S button. After a brief calculation, new results will appear. The Depth value now displayed is the amount you need to shift the hull vertically to hit the target displacement at the design waterline. 7. On the main screen, select the Hull surface. 8. Right-click on the Move button. In the Move Selection dialogue, set the V value to the opposite of that shown for Depth in the Instant Hydrostatics window, i.e. if Depth is U.041, set the V to D.041. Click on OK. 9. Click on the small H button to close the Instant Hydrostatics window. Note: If the value shown for Trim in the Instant Hydrostatics window is very large (> 1 degree) then it may take a few iterations of step 8 to hit the target draft.

4.6 Adding the Transom

We will create a cylindrical surface, Transom, by extruding a curve, Transom Shape. Then we will move the Transom to its correct position and intersect it with the Hull. The top of the transom will be defined by an embedded curve, Transom Top. The surface will them
126

Tutorial 4 be trimmed off at a combination of the curves Transom Top and Transom-Hull intersection. To create the cylinderical transom: 1. Create a new curve: Field
Name Tab Plane Semi-Axes Center Angles

Entry
Transom Shape Arc Top Circular check box checked Radius = 30 Somewhere 30 ft ahead of the transom 0 and 10

2. Create a new surface named Transom by extruding the Transom Shape curve upward by 5 feet. 3. Right-click the Rotate button. 4. In the dialogue box, specify a Transverse axis and an angle of 15, and then click OK. 5. In S Side view, move the transom so that it intersects the hull. You may find the transom easier to move if you reposition the base-point closer to the transom. 6. Select the Hull and Transom surfaces. 7. Click the Surf-Surf Intersect button, set the tolerance to 0.1 in. and click OK. 8. This generates two intersection curves: Transom Int1 (embedded on Hull) and Hull Int1 (embedded on Transom). Rename Transom Int1 to Hull-Transom, and Hull Int1 to Transom-Hull. 9. Trim Hull off at the intersection with the transom: select the Hull surface, click on the Trim Surface button, in the Trim Surface Hull dialogue, select the curve Hull-Transom and
127

Tutorials click on OK. Answer Yes at the appropriates Keep This Domain prompt and No to the others. We cannot yet trim the transom surface as we do not have a curve which completely describes where to trim the surface. To establish the top of the transom: 1. In Create mode, click the Create Point button. 2. In the Create Point dialogue, type the following information, and click OK: Field
Name Tab Host

Entry
Transom Corner Embedded Curve radio button selected Transom-Hull

3. Working in Front view, move the point Transom Corner to the top end of the curve Transom-Hull. Tip: pull the point up above the end of the curve and it will jump back to the end of the curve. 4. Create an embedded curve, Transom Top, embedded on the surface Transom and having 3 vertices. 5. Attach the outboard end of Transom Top to the point Transom Corner. 6. In Front view, edit Transom Top to the desired shape of the transom at deck level. You should position the middle control point at the same height as the vertex at centreline in order to maintain tangency across the centreline. (See Figure 4-4.)

128

Tutorial 4

Hull outline

Transom Top curve

Figure 4-4: Transom Top curve To trim off the excess transom: 1. In Edit mode, with the outboard vertex of Transom Top selected, click the Join Curves button. In the Join Curves dialogue, name the new curve Transom Trim, pick Transom-Hull and click on OK. 2. Select the surface Transom and click the Trim Surface button, in the Trim Surface Transom dialogue, select the curve Transom-Hull and click on OK. Answer Yes at the appropriates Keep This Domain prompt and No to the others.

4.7 The Keel

To create the keel, we will first layout the bottom of the keel with a free curve, then the top with a curve embedded in the hull, and finally create the keel as a ruled surface between these two curves.

129

Tutorials 1. Create a free curve, Keel Bottom, at V = -4, to establish a 4 ft draft. We specified 4 vertices and degree 2 and put the two ends at L = 22 and L = 9. 2. In Top view, edit the curve to the desired shape. You could have used a foil curve, but a true foil shape is not desirable for such a long keel. 3. Create an embedded curve, Keel Top, with 4 vertices and degree 2, embedded on the surface Hull, and edit it to the desired shape. 4. Create a ruled surface, Keel, between the curves Keel Top and Keel Bottom. If the surface is twisted (its outline looks like a bow tie), it is because the two curves run in opposite directions. To fix this, select one of the curves, go to edit mode and click on the Reverse Ends button. Then select the Keel surface and click on Edit Regenerate Object. 5. Add another column at the same location as the bottom column. 6. Select the bottom column, switch to Isolate and straighten the bottom column between the forward-most and aft-most vertices. Pick a vertex near the middle of the column and switch to Rows to check your work.

4.8 The Deck

We will construct the deck from edge curves. We already have Transom Top. We need to create Deck CL, Deck Fwd and Deck Edge. To create Deck CL: 1. Create a point, Deck at Bow, embedded on the surface Hull, and move it to the top of the stem.
130

Tutorial 4 2. Create a point, Transom Top at Center, embedded on the curve Transom Trim, and move it to the top of the transom at the centerline. 3. Create a new curve: Field
Name Tab End 1 End 2

Entry
Deck CL Free select: Deck at Bow check: Attach to point select: Transom Top at Center check: Attach to point

To create the curve Deck Fwd: 1. Create a free curve, Deck Fwd, as a degenerate curve: check the Degen. (Point) check box in the Create Curve dialogue. Note: A degenerate curve is a curve that is condensed to a single point - all of its vertices are forced to lie at a given point in space. 2. Attach Deck Fwd to the point Deck at Bow. To create the curve Deck Edge: Create a curve: Field
Name Tab Type Axis Parameter

Entry
Deck Edge Surf Row/Col Embedded Row 0 131

Tutorials
Host Surface Hull

To create the Deck surface: 1. Create a new surface: Field

Surface Name Tab Size Column Mesh Row Mesh

Entry
Deck Dimensions L = 24; T = 5; V = 0 Number: 3; MaxDegree: 2 Number: 3; MaxDegree: 2

2. Move it roughly into place. 3. Attach the four edges of the surface Deck to the following curves: Col 0 Deck Fwd Col 2 Transom Top Row 0 Deck CL Row 2 Deck Edge

Note that you may need to drag some of the vertices past the appropriate corners in order to pull the surface into the correct shape. This exercise has established a rather complex chain of dependencies. The hull depends on the transom and two curves embedded on it. The keel and the deck both depend on the hull. The keel also depends on the curve Bottom of Keel. To check what an object's dependents are, select the object and click on the Information (I) button on the lower left of the screen.

4.9 The Cabin

By now you should have a good feel for some of the things you can do with Autoship. By using the Information button and Attributes,
132

Tutorial 4 you should be able to figure out how the cabin was created in AS7TUT4.PR3.

4.10 Groups
Groups provide a way of putting together the parts for viewing, calculating weight and volume, and exporting to Autohydro and Autobuild. 1. Create a group, Main, which includes all the surfaces made in this tutorial. Render the Main group to see your vessel. 2. Mirror the Main Group by selecting Edit Attributes and in the Group Editor, click on the name Main, click Stbd + Port and then click OK. The result is a complete boat. 3. After creating the Main group, make a copy of this Group and call it Heeled 15. Then, with the group Heeled 15 selected, right-click the Rotate button. Type 15 degrees and click OK. The result is the boat heeled over 15 degrees. This lets you look at heeled waterlines and even see Heeled Buttocks! Try Quick Hydrostatics on this group. Remember to save your work.

4.11 Summary
This concludes Tutorial 4. If you have done all four tutorials, you have now seen many different ways to design a hull in Autoship. With a little practice, you should be able to design your own hull quickly and easily.

133

Tutorials

134

Tutorial 5

Tutorial 5 - Ro-Ro Carrier

13.5m

140m 12.1m Figure 5-1: Ro-Ro Hull

5.1 Introduction Ro-Ro Carrier

TUT5.PR3 is intended as a ro-ro vessel. To create a voluminous hull, this design features a vertical panel running from bow to stern which joins the formed lower portion of the hull along a knuckle line. The hull also has a bulbous bow and a stern bulb. Tutorial 5 shows one way to generate such a hull form. Take a look at the TUT5.PR3 file before continuing. The hull is composed of four surfaces and the bow and stern bulbs are added as separate surfaces. Remember that this tutorial is for guidance only, and that with experience and skill you will be able to develop more suitable design techniques for your own work.

135

Tutorials

5.2 Starting Out

To begin: 1. Create a New project. 2. Set units to Meters and Tonnes. 3. Select Settings - Preferences. 4. Click the Coordinate System button. 5. Click the Naval /Aircraft (US) radio button. 6. Save the file.

5.3 Midship Section

As in Tutorial 1, we will extrude a midship curve to generate the hull: 1. Create a Free curve, Midship Section, with 3 control points and degree 2, having End 1 at L = 55F, T = 12.1S, V = 6.3U and End 2 at L = 55F, T = 0, V = 0. 2. Select the middle control point and position it at V = 0 and about T = 10. Change it to a knuckle (Toggle Corner button), and then apply a fillet (Radius Corner button). We used a 3.0m fillet. (See figure 5-2.)

136

Tutorial 5

Figure 5-2: Midship Section Curve, Front View You could generate a hull surface by simply extruding this curve forward or aft from amidships. However, the resulting surface would have two knuckles or chines, one just above and one inboard of the vertex you used to generate the radius. To avoid this problem, we will copy the curve Midship Section and edit out the knuckles while using Midship Section as a template: 3. Copy the curve Midship Section to Midship: with the curve Midship Section selected, click on the Clone (Shift Copy) button, name the curve Midship. 4. Switch to Edit mode and in Front view zoom in on the bilge radius area. 5. Select vertex 1 and click on the Toggle Corner button. 6. Select vertex 3 and click on the Toggle Corner button. 7. Using the arrow keys on the keyboard, move vertex 3 inboard until the shape of the lower portion of the curve Midship roughly matches Midship Section. Try to keep track of how far the vertex is moved. 8. Using the arrow keys on the keyboard, move vertex 1 up by the same amount vertex 3 was moved inboard. Straighten the curve between vertex 0 and vertex 2.
137

Tutorials 9. Repeat steps 7 and 8 until the shape of the curve Midship matches the curve Midship Section. (See figure 5-3.)

Figure 5-3: Midship Curve, Front View

5.4 The Hull Forward

It is fairly common to design a shape using surfaces that fit to each other along their original, untrimmed edges. In order to ensure that the two edges match without gaps, there are special considerations that must be taken into account. One method of fitting the edges together is to use the Attach routine. However, this has two shortcomings: the two surface edges may wobble and leave minute gaps; and the attached edge definition is not supported in the IGES file type thus the fitted edges cannot be exported as an IGES file. Another method is to use the Match routine. This will match the surface edge to the object indicated within a set tolerance, but may also add extra vertices, thus making the surface more difficult to fair. The only way to absolutely guarantee that the two surface edges are identical is for the edges to be identical in degree of curvature, number of vertices and position of vertices. There are tricks to use to construct a shape from multiple surfaces that ensure that the edges match properly. We will experiment with them in the forward portion of the hull.

138

Tutorial 5 First, we will create the surface Hull Forward Upper as a ruled surface between two curves: Deck Edge Fwd and Knuckle Fwd. To create the curve Deck Edge Fwd: 1. Create a Free curve, Deck Edge Fwd, with 3 control points and degree 2, having End 1 at L = 55 F, T = 12.1S and V = 13.5 and End 2 at L = 137.5 F, T = 0 and V = 13.5. 2. In Top view, move vertex 1 to L = 137.5F and T = 12.1S. 3. Insert another vertex between vertex 1 and vertex 2 and move this vertex longitudinally to form the bow rounding. We suggest you keep the shape of this curve simple so that this edge-matching method will be easier to understand. (See figure 5-4.)

Figure 5-4: Deck Edge Fwd Curve, Top View To create the curve Knuckle Fwd: 1. Copy the curve Deck Edge Fwd, name the new curve Knuckle Fwd. 2. Move Knuckle Fwd downward 2m. 3. In S Side view, edit Knuckle Fwd to the desired shape. Adjust the vertices in the vertical direction only. You may find it advantageous to add a control point or two. Be sure that the vertex 0 is at L= F55, T = 12.1S, V = U6.3 and that vertex 1 is at T = 12.1S, V = U6.3 so that Knuckle Fwd connects with Midship. (See figure 5-5).
139

Tutorials

Figure 5-5: Knuckle Fwd Curve, S Side View To create the surface Hull Forward Upper: 1. Create a new surface, Hull Fwd Upper, by extruding the curve Knuckle Fwd upwards by 2m. 2. Attach the upper column of Hull Fwd Upper to the curve Deck Edge Fwd to position the top edge of the surface, and then undo the attachment. Note: Extruding the surface from the curve Knuckle Fwd ensures the bottom edge of the surface matches the curve Knuckle Fwd.

We will now create the surface Hull Fwd Lower by sweeping the curve Midship forwards along the curve Knuckle Fwd. This will create a surface that is identical at the aft end to the Midship Curve and identical at the top edge to both the curve Knuckle Fwd and bottom edge of the surface Hull Fwd Upper. The forward edge will be matched to a template curve, Stem.

To create the curve Stem:

140

Tutorial 5 1. Create a Free curve, Stem, with 5 control points and degree 2 having End 1 at L = 137.5 F, T = 0 and V = 11.5 and End 2 at L = 130F, T = 0 and V = 0. 2. Edit the shape as shown in figure 5-6.

Figure 5-6: Stem Curve, S Side View To create Hull Fwd Lower: 1. Create a Sweep surface, Hull Fwd Lower, for the Pattern Curve use Midship, for the Guide Curve use Knuckle Fwd and check the Parallel check box. 2. Zoom in on the forward end and drag the vertices of the forward-most column (col 4) into a close match to the curve Stem. You may find it easier with Isolate on. Be sure to position all the vertices at the centreline. 3. Use the Match feature to match the shape of column 4 to the curve Stem: click on the Attach button, in the Attach Surface dialogue, pick Match, specify the curve Midship and click on OK. Note: The Match operation works well in this instance because the columns of surface Hull Fwd Lower have five vertices and the curve Stem also has five vertices.

141

Tutorials 3. Use Straighten to move all the vertices of the bottom row to the centreline. Note that you will have to move the vertex on column 3 aft. 4. Edit the shape of column 2 and 3 to achieve the shape desired. Do not move the vertices in the top row or else the top edge will no longer match the curve Knuckle Fwd. Note: In Body view, the control points on columns 0 and 1 must be kept identical to ensure the forward portion of the hull will match up with the aft portion of the hull at midships. 5. If desired, add another row inboard of the row at centreline and convert it to a corner or knuckle row to define the flat bottom.

5.5 The Bow Bulb

We will create the bulbous bow as a separate surface and then trim it to the Hull Forward Lower surface.

To create the Bulb at the bow: 1. In Front view, Draw a curve, Bulb Section, to represent the sectional shape of the bulb. Use 3 vertices, degree 2 and make it approximately 4m high by 2m wide. Make sure the two end vertices are at T = 0 (Refer to Tutorial 3, Creating the Housetop Surface for instruction on how to Draw a curve) (See figure 5-7).

142

Tutorial 5

Figure 5-7: The Curve Bulb Section

2. Create a new surface, Bulb Fwd, by extruding the curve Bulb Shape longitudinally. We specified a length of 20m, 3 columns and degree 2. 3. Move the surface into position. 4. Close the forward end of the shape: add another column at the same location as the forward-most column and set all of its vertices to the same vertical coordinate. We uses 2.5. Make sure they are all at T = 0. 5. In S Side view, shape the top, bottom and forward edges by eye. Insert other columns as needed. The forward-most two columns define a smoothly closed shape. If you move any of the vertices on either of these column longitudinally you will distort the front end of the bulb. 6. In Top view, shape the middle row. 7. Ensure tangency across the top: add another row at the same position as the top-most row and move its vertices outboard a little. Use these vertices to alter the sectional shape.
143

Tutorials 8. Ensure tangency across the bottom: add another row at the same position as the bottom-most row and move its vertices outboard a little. Use these vertices to alter the sectional shape. Tip: Keep the aft-most vertex of this row at T = 0 to obtain a more usable intersection with the hull. To fit the Bulb: 1. Select both Hull Fwd Lower and Bulb Fwd. 2. Click the Surf-Surf Intersect button to generate the intersection curves. Note: You may find an additional set of intersection curves positioned along the centreline, or the intersection curves may extend along the centreline at the bottom. These portions are not needed, so they can be deleted. 3. Rename Bulb Int1 to Hull Fwd Lower-Bulb Fwd and Hull Forward Lower Int1 to Bulb Fwd-Hull Fwd Lower. 4. Select Bulb Fwd and click on the Trim Surface button. 5. In the Trim Surface Bulb Fwd dialogue, select the curve Bulb Fwd-Hull Forward Lower and click on OK. Answer Yes to the appropriate Keep this Domain prompt and No to the others. To create the trimmed Hull Forward Lower: 1. Using the same method as 3 and 4 above, trim Hull Forward Lower at the intersection with the Bulb. You may have to rework the aft end of the intersection curve to obtain a closed curve. 2. Select View-Render to see your work in perspective.

144

Tutorial 5

5.6 The Hull Aft

A similar procedure could be followed to design the stern section. However, we will introduce another method which can be used to build up the hull shape from curves while ensuring the different parts match where they join. In this method, the hull will be defined with a single surface, yet constructed from more than two curves.

To create the curve Deck Edge Aft: 1. Create a Free curve, Deck Edge Aft, with 3 control points and degree 2, having End 1 at L = 55 F, T = 12.1S and V = 13.5 and End 2 at L = 2.5 A, T = 12.1 and V = 13.5.

To create the curve Knuckle Aft: 1. Copy the curve Deck Edge Aft, name the new curve Knuckle Aft. 2. Move Knuckle Fwd downward 6m. 3. In S Side view, in Edit mode, click on the middle control point and add another control point using the Refine option. Edit Knuckle Aft to the desired shape. Adjust the vertices in the vertical direction only. Be sure that both the forward-most vertex and the next one aft is at V = U6.3 so that Knuckle Aft connects smoothly with Knuckle Fwd. (See figure 5-8).

145

Tutorials
Deck Edge Aft

Knuckle Aft

Knuckle Fwd

Figure 5-8: Deck Edge Aft and Knuckle Aft Curves To create the curve Knuckle Aft: 1. Create a Free curve, Centreline Aft, with 6 control points and degree 2, having End 1 at L = 55 F, T = 0 and V = 0 and End 2 at L = 2.5 A, T = 0 and V = 5. 2. Arrange the vertices as shown in figure 5-9.

Figure 5-9: Centreline Aft Curve To create the surface Hull Aft: 1. Create a Sweep surface, Hull Aft, using Midship as the Pattern Curve and Centreline Aft as the Guide Curve, check the Parallel checkbox.

146

Tutorial 5 You will notice that the surface is created below and to the port of the curve Centreline Aft. Remember that a Sweep surface sweeps the first end of the Pattern curve along the first Guide curve. In this case, the first end of the curve Midship is up at the knuckle line not at the baseline. In this case, there is an easy fix: 2. Select the curve Midship and go to Edit mode. 3. Click on the Reverse Ends button. 4. Select the surface Hull Aft. 5. Select the Edit Regenerate Object menu option. This will re-construct the surface in the originally intended manner. Now, we must form the surface. 6. Attach the upper edge of the surface to the curve Knuckle Aft: switch to Edit mode, select the upper-most row (Row 4), click on the Attach button, pick Attach to Curve, and for Attach to pick Knuckle Aft. 7. Move the aft-most two contol points of Row 3 downwards so that they lie below the curve Knuckle Aft. Try to position them so Row 3 is smooth. 8. In Front view, check each column of control points to make sure there are no bumps or hollows. Turn on the surface mesh and inspect it in each view to make sure it has a smooth flow. Now we continue to build the Hull Aft surface higher. 9. Add another row at the same position as the top-most row (Row 4): select Row 3, click the Add Row or Column button and for Proportion, input 1. 10. Select the new top-most row, (Row 5). You may find it easier to locate Row 5 by toggling to Edit points. 11. Detach Row 5 and then Attach it to the curve Deck Edge Aft.
147

Tutorials 12. Turn Row 4 into a corner: select Row 4 and click on the Toggle Corner button. This completes the Aft Hull surface. You have now seen two ways to construct a large surface from several curves, and assure that the overall shape is contiguous and smooth.

5.7 The Stern Bulb

We will create the stern bulb in three steps: 1. Define the lower profile of the stern bulb by creating a curve called Stern Bulb Profile in side view. See Figure 5-10.

Figure 5-10: Curve Stern Bulb Profile 2. Create a surface, Bulb Aft, as a type Rotate surface; pick Longitudinal for Axis and specify an angle of 180 for Rotation. Tip: move Stern Bulb Profiles base point to the height of the centreline of the bulb by default, the surface of rotation is be created by revolving the curve about its base point.

148

Tutorial 5 3. If the Bulb Aft is not already in the correct position, reposition it and then intersect it with Hull Aft. Remember to rename the intersection curves. 4. Trim both the Bulb Aft and Hull Aft.

5.7 Summary
This concludes Tutorial 5. Have a good look at the project to get an idea of how the groups are constructed. If you want to test the hydrostatics, the design draft is 5.4 m.

149

Tutorials

150

Tutorial 6

Tutorial 6 - Oil Rig

66m

28m

104m

Figure 6-1: Oil Rig

6.1 Introduction Oil Rig

Autoship can be used to create accurate models of large, complex structures which are not boats or ships. This oil rig is one such example. This model was created by constructing one quarter of the structure and then copying, mirroring, and grouping it to form the rest of the structure. In this way, you can create a model from a minimum number of individual components. This tutorial also shows how to export a complex structure to Autohydro. TUT6.PR3 and this tutorial show one way to construct a model for such a structure.

151

Tutorials

6.2 Starting Out

To begin: 1. Click on File New to initialize Autoship. 2. Set units to Meters and Tonnes. 3. Set the coordinate system to Naval /Aircraft (US). Our approach for the construction of this rig will be to create the elements needed for one quarter of the structure and then assemble them into a group. Then, by using copy and mirror operations upon the group, we will produce the entire model that will be used for visual purposes. Finally, we will re-assemble the basic elements to produce a different model of the same structure which can be exported to Autohydro.

6.3 Pontoon
First, we will create two curves, Midship and Waterline and then sweep Midship along Waterline to create a surface that represents the aft, forward one-eighth of one pontoon. Then, through a series of clone and mirror operations, we will create the aft half of one pontoon. To create the curve Midship: 1. Create a new curve, Midship, with 3 Control Pts and Max Degree 2 having End 1 at 0, 5, 0 and End 2 at 0, 0, 5. 2. Move the middle Control Point (not Edit Point) to 0, 5, 5, toggle it to a corner and then use the Radius Corner button to form a Radius of 1.0. To create the curve Waterline: 1. Create a new curve, Waterline, with 3 Control Pts and Max Degree 2 having End 1 at 0, 5, 0 and End 2 at 50, 0, 0. 2. Move the middle Control Point to 50, 5, 0 and then toggle it to a corner and then use the Radius Corner button to form a Radius of 5.0.
152

Tutorial 6

Figure 6-2: The Curves Midship and Waterline in Para View To create half of the upper aft portion of the pontoon: 1. Create a Sweep surface, Upper Surf, by sweeping the curve Midship along the curve Waterline. To create half of the lower aft portion of the pontoon: 1. With the surface Upper Surf selected, click on the Clone button. In the New Group dialogue, give the name Lower Clone. 2. Click in the S Side view window, if it is not the currently selected view. 3. With Lower Clone selected, click on the Flip Vertical button.

To create the other half of the aft portion of the pontoon:

153

Tutorials 1. Select both Upper Surf and Lower Clone and click on the Clone button. In the New Group dialogue, give the name Port Clone. 2. Click on the Front view window. 3. With Port Clone selected, click on the Flip Horizontal button. To create the half of the the pontoon: 1. Create a group, Pontoon Half, consisting of Upper Surf, Lower Clone and Port Clone. 2. Move Pontoon Half 33.0m to starboard. (Tip: right-click on the Move button.)

6.4 The Column

We will create one column and copy it to produce the others. The column will be constructed in two parts: the lower and the upper part. To create the cone (lower part): 1. Create a Rectangle type curve, Cone Bottom to represent the bottom of the cone. We set Plane to Top; Centre at 42.0, 0.0, 5.0, specified Square and a Height of 7.5. You can round the corners of the bottom curve if you like. 2. Apply a 0.5m radius at each corner. 3. Create an Arc type curve, Cone Top, to represent the top of the cone and the bottom of the cylinder. We set Plane to Top; Centre at 42.0, 0.0, 10.0, specified Circular and a Radius of 3.0. 4. In Top view, compare the arrows at the beginning of Cone Bottom and Cone Top to ensure that both curves start at the same relative location - aft or forward, and that both curves point the same way.
154

Tutorial 6 5. Create a Develop surface, Cone between Cone Bottom and Cone Top. To create the cylinder (upper part): 1. Create an Extrude surface, Cylinder, by extruding the curve Cone Top 18m vertically.

6.5 The Cross Beams and Diagonals

We will create one cross beam and one diagonal and copy them to produce the others. To create a cross beam: 1. Create an Arc curve, Cross Beam Template. We set Plane to Side; Centre at 42.0, 0.0, 7.5, specified Circular and a Radius of 2.0. 2. Create an Extrude surface, Cross Beam, by extruding the curve Cross Beam Template 33m to port. 3. Obtain the Surf-Surf intersection curves of Cross Beam and Cone and trim off Cross Beam at the intersection. To create a diagonal: 1. Create a curve, Diagonal Axis to represent the axis, or centreline of the diagonal tube. We set Control Pts to 2, Max Degree to 1, End 1 to 42.0, 0.0, 5.0 and End 2 to 42.0, P33.33, 28.23. Note: we will need to trim off the top of the Diagonal and so need to extend it past where it will be trimmed at L = 42.0, T = 33.0P, V = 28.0. In this case, we chose to extend the curve 10%, or T = 0 + (1.1 x 33.0P) = 33.33P and V = 5U + (1.1 x (28.0U 5.0U)) = 28.23U. (The 5U is the V at End 1.) 2. Create a Tube Sweep surface, Diagonal using the curve Diagonal Axis. We set Radius to 1.0.

155

Tutorials 3. Obtain the Surf-Surf intersection curves of Diagonal and Cross Beam. Note that Diagonal penetrates Cross Beam twice, so there will be more than one intersection curve generated. To avoid later confusion, delete the unnecessary curve(s). 4. Create a Dimensions type surface, Temp, with L = 6, T = -4 and V = -4, Column Mesh: Number 2, Max Degree 1; Row Mesh: Number 3, Max Degree 1. 5. Move Temp by 39.0A, 29.0P, 28.0U. Note: We want to move the centre of the surface (L = 3.0, T = P4.0, V = 0) to L = 42.0, T = P33.0, V = 28.0. Hence the displacement is L = (42.0 3.0) = 39.0, T = (P33.0 P4.0) = P29.0, V = (28.0 0) = 28.0. 6. Obtain the intersection of Temp and Diagonal and rename the curves. 7. Trim Diagonal off at the intersection with Cross Beam and the intersection with Temp. You may wish to delete the curve embedded on Temp and the surface Temp. To create multiples of the columns, cross beams and diagonals: 1. Create a group, Column & Bracing, which contains the surfaces Cone, Cylinder, Cross Beam and Diagonal. 2. Clone the group Column & Bracing, name it Column & Bracing 2 and move it 28.0m forward. 3. Move Column & Bracing 33.0m to starboard. Note that Column and Bracing 2 also moves, since it is a clone. (Refer to figure 6-3.)

156

Tutorial 6

Figure 6-3: Groups Column & Bracing and Column & Bracing 2 in Para View.

6.6 The Deck Assembly

The deck assembly includes two parts: the horizontal deck and the vertical surface, Deck Skirt. As with the pontoons, columns and braces, we will create one quarter of each structure and use that to produce to entire structure. To create the vertical surface Deck Skirt: 1. Create a curve, Deck Edge, using the Draw Curve option, that represents the outer edge of one quarter of the deck. (Once you have drawn the curve, click the right mouse button, name the curve Deck Edge, and set Maximum Degree to 1, and Method to Control Points. See the Autoship Reference Manual for more details.) Refer to figure 6-4.

157

Tutorials

Figure 6-4: The Curve Deck Edge in Top View 2. Toggle vertices 1,2, 3,4 and 5 into corners. 3. In the Attributes dialogue, set the degree to 2 and resolution to 40. 4. Apply a radius of 1.5m at vertices 2, 3 and 4. 5. Move the curve Deck Edge upwards 28.25m. 6. Create an Extrude surface, Deck Skirt, by extruding the curve Deck Edge downward by 3.0m. To create the horizontal surface deck: 1. Create a curve, Deck Template, having End 1 at 0, 0, 28 and End 2 at 60, 0, 28. 2. Create and Extrude type surface, Deck, by extruding Deck Template 50.0m to starboard. 3. Obtain the intersection of Deck with Deck Skirt and trim off Deck to that intersection. 4. Create a group, Deck Quarter, containing the trimmed surface Deck and the surface Deck Skirt.
158

Tutorial 6

6.7 Assembling One Quarter of the Rig

All the components needed to make up one-quarter of the rig have been created. We will now assemble the components into one quarter of the rig and copy and mirror the quarter to produce the entire rig. 1. Create a group, Quarter, containing the group Pontoon Half, Column & Bracing, Column & Bracing 2 and Deck Quarter. 2. Clone the group Quarter, and name the new group Quarter 2. 3. In the S Side view, with Quarter 2 selected, click on the Flip Horizontal button. 4. Make another group, Main, which contains Quarter and Quarter 2. 5. With Main selected, in the Group Editor dialogue, click on the Stbd + Port button. Your oil rig is complete!

6.8 Assembling an Autohydro model

Autohydro models are comprised of parts and components. A component simply describes an enclosed volume in space. A Part is composed of a component, or a set of components, and is assigned specific attributes, thereby creating a complex volume with specific behaviour. An important attribute is the side designation whether the part should exist only on the port side or the starboard side, or be mirrored across the centreline. Autoship exports a selected group to Autohydro as a single-part model, and each object contained in the group is exported as a component of the single part. Therefore, it is important that each object contained in the group defines a single, enclosed volume. Further, the side of the part will be determined by the group: If the Stbd + Port check box for the group is turned on, then the part will be a centreline part, otherwise it will be a starboard part.
159

Tutorials Consequently, we need to construct a different model in which each object contained in the export group describes a single volume. We could construct half of the model and have it mirrored across the centreline, but then we would not have access to the individual pontoons or columns in case we wished to fit tanks inside them. Instead, we will model each volume separately: our model will consist of separate components that describe: Each entire pontoon (2 components); Each vertical column (8 components); Each cross beam (4 components); Each diagonal (8 components);

We will not bother with the deck structure. Tip: To make it easier to visualize the following operations, we suggest you go to the Attributes dialogue and turn off the visibility of all groups except for Pontoon Half. To create the pontoon components: 1. Create a clone, Pontoon Half 2, of the group Pontoon Half and flip it to the other side of L = 0. 2. Create a group, Pontoon.S, which contains the group Pontoon Half and Pontoon Half 2. 3. Create a clone, Pontoon.P, of the group Pontoon.S, and flip it to the other side of T = 0. To create the column components: 1. Create a group, Column 1.S, containing the surface Cone and the surface Cylinder and move 33.0m to starboard. Move its base point to T = 0. 2. Create a clone, Column 2.S, of the group Column 1.S and move it 28.0m forward.

160

Tutorial 6 3. Create a clone, Column 3.S, of the group Column 2.S and move it 28.0m forward. 4. Create a clone, Column 4.S, of the group Column 3.S and move it 28.0m forward. 5. Create a clone, Column 1.P, of Column 1.S and flip it to the other side of the centerline. 6. Create a clone, Column 2.P, of Column 2.S and flip it to the other side of the centerline. 7. Create a clone, Column 3.P, of Column 3.S and flip it to the other side of the centerline. 8. Create a clone, Column 4.P, of Column 4.S and flip it to the other side of the centerline. To create the cross beam components: 1. Create a clone, Cross Beam Clone, of the surface Cross Beam and move it 33.0m to starboard. 2. Create a group, Cross Beam 1, of Cross Beam Clone and in the Group Editor, check the Stbd + Port checkbox. 3. Create a clone, Cross Beam 2, of Cross Beam 1 and move it 28.0m forward. 4. Create a clone, Cross Beam 3, of Cross Beam 2 and move it 28.0m forward. 5. Create a clone, Cross Beam 4, of Cross Beam 3 and move it 28.0m forward. To create the diagonal components: 1. Create a clone, Diagonal 1.S, of the surface Diagonal and move it 33.0m to starboard. Move its base point to T = 0. 2. Create a clone, Diagonal 2.S, of the group Diagonal 1.S and move it 28.0m forward.

161

Tutorials 3. Create a clone, Diagonal 3.S, of the group Diagonal 2.S and move it 28.0m forward. 4. Create a clone, Diagonal 4.S, of the group Diagonal 3.S and move it 28.0m forward. 5. Create a clone, Diagonal 1.P, of Diagonal 1.S and flip it to the other side of the centerline. 6. Create a clone, Diagonal 2.P, of Diagonal 2.S and flip it to the other side of the centerline. 7. Create a clone, Diagonal 3.P, of Diagonal 3.S and flip it to the other side of the centerline. 8. Create a clone, Diagonal 4.P, of Diagonal 4.S and flip it to the other side of the centerline. To create the export group: 1. Create a group, Autohydro, which contains all the groups/clones you have formed in this section except for Pontoon Half 2. Do not check the Stbd + Port checkbox. 2. With the group Autohydro selected, click on the File Export Autohydro menu option. 3. In the Export Autohydro file dialogue, give a name and indicate a directory to store the file in and click on OK. 4. At the prompt User Defined Sections?, click on No. 5. At the prompt Name for GF1 part, click on OK. 6. Start Modelmaker, load the file just written and experiment with the various views. Note: You may notice that some of the components are not defined with many sections. This is because you answered No to the prompt User Defined Sections. To improve the definition, in Autoship open the Contours dialogue and set up a series of stations that provides coverage over the entire length of the pontoons (~3m interval) while
162

Tutorial 6 being more dense around the columns, cross beams and diagonals and at the ends of the pontoons (~.3m interval).

6.9 Summary
This finishes tutorial 6 the last of the tutorials. You have now explored many of the important features of Autoship and have experimented with various different methods of constructing a model. You have probably realized by now that Autoship is a very powerful program and that there is a lot to learn. As with many things, the only way to learn Autoship is to work with it, and that will take time. One option to shorten the time is to take a training course. The best option, however, is to experiment and seek help when things go wrong. Good luck and have fun!

163

Tutorials

164

Auto3D Module

Appendix: Auto3D Module

Auto3D is a specialized module for working with Autoship DRA files created in the Autoship DOS version, or Autoyacht (DOS), as well as Autoship for Windows. You can perform the following functions: Rendering Auto3D shows solid (or shaded) views of models. You can also use it to produce a rotating slide show of your Autoship model. Auto3D generates output for plotters, either directly or to a file. Auto3D generates output to various CAD programs.

Plotter Output

CAD Output

Running Auto3D

165

Appendix

To run Auto3D, double-click on the Auto3D icon in the Autoship program group. The main display appears:

Figure 1: The Auto3D main display

166

Auto3D Module

The File Menu

The file menu is used for importing and exporting files, and to print files.

The File menu contains the following items:

Load File Append File Save DRA CAD Out Print Printer Setup Plot Plotter Setup Exit

Load an initial DRA file. Add another DRA file to the initial file. Save DRA file. Export the model to a variety of CAD formats. Print the model on the screen. Bring up the Windows Printer Setup dialog box. Bring up the Plotter Preview dialog box to set up for a plot. Bring up the Plotter Setup dialog box for configuring Auto3D for your plotter. Exit Auto3D.

To plot a view:
167

Appendix

Before plotting a view, select File-Plotter Setup and ensure the configuration settings are correct for your plotter. Then select File-Plot. In the Plotter Preview dialog box that appears, specify how the view is drawn. When all the settings are correct, click OK. To export to a CAD program:

Select File-CAD Out. In the CAD Exchange dialog box that appears, select the type of exchange and the destination to send the file to. If you just want a typical lines plan of Body, Plan and Profile, use the 2D exchange, with a file for each view, as it is the fastest and easiest method.

168

Auto3D Module

The Edit Menu

The Edit menu is used to copy views of the model or its parts to the clipboard for use in graphics programs. It is also used to scale the model or move the origin.

Copy Wireframe Copy the wire mesh view of the model into the clipboard, for use with graphics programs. Copy Hide Copy the wire mesh view into the clipboard, with the hidden lines removed, for use with graphics programs. Copy the rendered view of the model into the clipboard, for use with graphics programs. Scale the model longitudinally, transversely and/or vertically. Move the origin by a specified amount. (The numbers you specify are always added to the origin, so if you want to move the model forward, you must type in negative numbers.) Compress DRA files that become unmanageably large.

Copy Render Scale Move Origin

Compress

169

Appendix

The View Menu

The View menu is used to control the way the model is viewed, or rendered. Rendering produces a shaded image of your vessel. If the DRA file was created with Autoship for Windows, and if the surface mesh was turned on, then after you load it into Auto3D you can render it by selecting View-Render. The shading depends on the light source you selected with View-Light Source.

Light Source Hide Render

Set the direction of the light source for rendering. Toggle between showing and removing hidden lines. Generate a solid representation of the model.

170

Auto3D Module

The Settings Menu

The Settings menu sets user preferences.

Units Page Margins

Set the units being used for the model. Set up the page margins for the printed page and select the specific printer to use. Set the font style and point size Set the background colour for the screen. Select which colours will show in the drawing. Note that each line type is associated with one colour. For Body view only, specify where to switch from showing contours on one side of the centreline, to showing contours on the other side. Typically, the mid-point of the model.

Font Background Colours to Show

Switch Sides At

171

Appendix

Spin Setup

Create a slide show of 13 rotational views of your model. Specify the rotation angle and the length of time each view remains on the screen. Vary the distance from which you see the 3D view of the model. Scale the model to fit the plotter or printer.

Perspective View Callibrate Print/Plot

172

Auto3D Module

The Side Icon Box

The Side Icon Box contains tools for controlling the way your model appears and for manipulating your model.

Zoom-In No Zoom Mirror Perspective Spin 1View 4Views

Zoom in on areas within current view Return the view to its full extent. When selected, shows both sides of the model. Gives a perspective view of the model. If Spin Setup is defined, starts the slide show of your model. Show single view of model. Show four views of the model. Note: Double-clicking in 1 View changes to 4 Views. Double-clicking in 4 Views changes to 1 View.

Single View Select a view to show for single view.

Tilt

Shows the amount of tilt in the current view. (Use the bottom bar controls to tilt your model.)

173

Appendix

Rotate

Shows the amount of rotation in the current view. (Use the side bar controls to rotate.)

Wires/Faces Select whether to show wires or surface faces for the model. Note: Only models exported from Autoship for Windows with mesh selected will have faces enabled.

174