0% found this document useful (0 votes)

244 views

Cell Broadcast

Uploaded by

Mehmet Gogebakan

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

244 views

Cell Broadcast

Uploaded by

Mehmet Gogebakan

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 73

BSC3153 Nokia GSM/EDGE BSS, Rel. BSS13, BSC and TCSM, Rel. S13, Product Documentation, v.

EC - SMS Cell Broadcast Handling

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

1 (73)

EC - SMS Cell Broadcast Handling

The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation. The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given as is and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document. Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL NOKIA SIEMENS NETWORKS BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA, THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT. This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws. The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG. Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only. Copyright Nokia Siemens Networks 2008. All rights reserved.

2 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

Contents

Contents
Contents 3 List of tables 4 List of figures 5 Summary of changes 7 EC - SMS CELL BROADCAST HANDLING 11 ECA CREATE MESSAGE WITH EDITOR 13 ECB CREATE/MODIFY MESSAGE TEXT PAGE BY PAGE 23 ECM MODIFY MESSAGE WITH EDITOR 37 ECR MODIFY MESSAGE PARAMETERS 41 ECS ACTIVATE MESSAGE 49 ECE DEACTIVATE MESSAGE 53 ECC DEACTIVATE BTS(S) 57 ECD DELETE MESSAGE(S) 59 ECP DISPLAY MESSAGE(S) 61 ECL DISPLAY BTS WORK LOAD 71

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

3 (73)

EC - SMS Cell Broadcast Handling

List of tables

4 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

List of figures

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

5 (73)

EC - SMS Cell Broadcast Handling

6 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

Summary of changes

Changes between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues.

Changes made between issues 14-0 and 13-0

The duplicate list of commands of the command group in section EC: SMS CELL BROADCAST HANDLING has been removed as part of general streamlining in the MML command reference documents.

Changes made between issues 13-0 and 12-0

ECB CREATE/MODIFY MESSAGE TEXT PAGE BY PAGE The value range of the parameter message index was extended to 8068 for BSCi/BSC2i and 15000 for BSC3i. MODIFY MESSAGE WITH EDITOR The value range of the parameter message index was extended to 8068 for BSCi/BSC2i and 15000 for BSC3i. MODIFY MESSAGE PARAMETERS The value range of the parameter message index was extended to 8068 for BSCi/BSC2i and 15000 for BSC3i. ACTIVATE MESSAGE The value range of the parameter message index was extended to 8068 for BSCi/BSC2i and 15000 for BSC3i. The value range of the parameter BTS identification was extended to 2000.

ECM

ECR

ECS

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

7 (73)

EC - SMS Cell Broadcast Handling

ECE

DEACTIVATE MESSAGE(S) The value range of the parameter message index was extended to 8068 for BSCi/BSC2i and 15000 for BSC3i. The value range of the parameter BTS identification was extended to 2000.

ECC

DEACTIVATE BTS(S) The value range of the parameter BTS identification was extended to 2000. DELETE MESSAGE(S) The value range of the parameter message index was extended to 8068 for BSCi/BSC2i and 15000 for BSC3i. DISPLAY MESSAGE(S) The value range of the parameter message index was extended to 8068 for BSCi/BSC2i and 15000 for BSC3i. The value range of the parameter BTS identification was extended to 2000.

ECD

ECP

ECL

DISPLAY BTS WORK LOAD The value range of the parameter BTS identification was extended to 2000.

Changes made between issues 12-0 and 11-0

ECA CREATE MESSAGE WITH EDITOR One execution printout was modified. One note was moved to another location. CREATE/MODIFY MESSAGE TEXT PAGE BY PAGE The value range of the parameter message index was extended to 5400. MODIFY MESSAGE WITH EDITOR The value range of the parameter message index was extended to 5400. One note on coding groups was removed. One execution printout was modified. MODIFY MESSAGE PARAMETERS The value range of the parameter message index was extended to 5400.

ECB

ECM

ECR

8 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

Summary of changes

ECS

ACTIVATE MESSAGE The value range of the parameter message index was extended to 5400. The value range of the parameter BTS identifier BTS was updated. DEACTIVATE MESSAGE(S) The value range of the parameter message index was extended to 5400. The value range of the parameter BTS identifier BTS was updated. DEACTIVATE BTS(S) The value range of the parameter BTS identifier BTS was updated. DELETE MESSAGE(S) The value range of the parameter message index was extended to 5400. DISPLAY MESSAGE(S) The value range of the parameter message index MI was extended to 8069. The value range of the parameter BTS identifier BTS was updated. DISPLAY BTS WORK LOAD The value range of the parameter BTS identifier BTS was updated.

ECE

ECC

ECD

ECP

ECL

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

9 (73)

EC - SMS Cell Broadcast Handling

10 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

EC - SMS CELL BROADCAST HANDLING

With this command group you manage cell broadcast messages. You can create, modify, activate, deactivate, delete, and display messages. Menu of the command group:
SMS CELL BROADCAST HANDLING COMMANDS ? A: B: M: R: S: E: C: D: P: L: Z; ..... ..... ..... ..... ..... ..... ..... ..... ..... ..... ..... ..... DISPLAY MENU CREATE MESSAGE WITH EDITOR CREATE/MODIFY MESSAGE TEXT PAGE BY PAGE MODIFY MESSAGE WITH EDITOR MODIFY MESSAGE PARAMETERS ACTIVATE MESSAGE DEACTIVATE MESSAGE (S) DEACTIVATE BTS (S) DELETE MESSAGE (S) DISPLAY MESSAGE (S) DISPLAY BTS WORK LOAD RETURN TO MAIN LEVEL

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

11 (73)

EC - SMS Cell Broadcast Handling

12 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECA CREATE MESSAGE WITH EDITOR

Function Parameters Syntax With the ECA command you create a new cell broadcast message. message identifier: message code: geographical scope: coding group, language identifier, message class, alphabet identifier: repetition rate;
ECA: <message identifier> : <message code> : <geographical scope> : <coding group> , (<language identifier> | <message class>, <alphabet identifier>): <repetition rate> ;

Parameter explanations

message identifier
The value range is from 0 to 999 for short messages of all types, and from 4096 to 4351 for cell broadcast data download to the SIM messages. The parameter is obligatory.

message code
The value range is from 0 to 1023. The value is used for differentiating between messages which have the same message identifier and thus share the same source and type. The parameter is obligatory.

geographical scope

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

13 (73)

EC - SMS Cell Broadcast Handling

The geographical scope indicates the geographical area over which the message code is unique as well as the display mode of the mobile. The parameter can have the following values:
1 2 3 4 ... ... ... ... CELL WIDE, DISPLAY MODE IMMEDIATE PLMN WIDE, DISPLAY MODE NORMAL LOCATION AREA WIDE, DISPLAY MODE NORMAL CELL WIDE, DISPLAY MODE NORMAL

The parameter is obligatory.

coding group
The coding group indicates the data coding scheme used to indicate the intended handling of the message at the MS, the alphabet/coding, and the language (when applicable). The coding groups of the cell broadcast data coding scheme are defined in 3GPP TS 23.038. If the message identifier is from 0 to 999, the parameter can have the following values:
1 ... GROUP 0000: DEFAULT ALPHABET, SELECT LANGUAGE 2 ... GROUP 0001: DEFAULT ALPHABET/UCS2 TEXT, MESSAGE PRECEDED BY LANGUAGE IDENTIFICATION 3 ... GROUP 0100: UNCOMPRESSED 8-BIT DATA OR DEFAULT ALPHABET/UCS2 TEXT, NO MESSAGE CLASS 4 ... GROUP 0101: UNCOMPRESSED 8-BIT DATA OR DEFAULT ALPHABET/UCS2 TEXT, WITH MESSAGE CLASS 5 ... GROUP 1111: 8-BIT DATA OR DEFAULT ALPHABET TEXT, MESSAGE CLASS

If the message identifier is in the range of 4096 to 4351, the parameter can have the following values:
4 ... GROUP 0101: UNCOMPRESSED 8-BIT DATA OR DEFAULT ALPHABET/UCS2 TEXT, WITH MESSAGE CLASS 5 ... GROUP 1111: 8-BIT DATA OR DEFAULT ALPHABET TEXT, MESSAGE CLASS

The parameter is obligatory.

14 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECA CREATE MESSAGE WITH EDITOR

Coding group 0000 is the recommended choice for the coding group because it is understood by all mobiles that can receive cell broadcast messages. Earlier releases' messages belong to this coding group. In this coding group, you can choose the language from a list of 13 languages, the alphabet is automatically the default 7-bit alphabet, and there are 93 characters per page in a message. Coding group 0001 is recommended when you want to define the language of the message, but the language is not among the 13 languages defined in the coding group 0000. In this coding group, the twoletter language identifier (defined in the ISO 639 standard) is written at the beginning of the message so that the first two letters are followed by <CR> = 0D H. You must also choose the alphabet used in the message. You can choose either the 7-bit default alphabet or the 16-bit UCS2 characters.

Note
The language identifier used in coding group 0001 must be written in lower case letters.

If you choose the default alphabet, you can write 90 characters on the first page of the message and 93 characters on the following pages of the message. Mobiles which have software complying with ETSI GSM phase 2 standards will display only the message text, not the language identifier. If you choose the UCS2 characters, you can write 40 characters on the first page of the message and 41 characters on the following pages of the message. Mobiles which have software complying with ETSI GSM phase 2 standards will display only the language identifier and the text is displayed as an apparently random string of characters.

Coding group 0100 is recommended when you want to send uncompressed 8-bit data or uncompressed text by using the default alphabet or UCS2 characters but you do not want to define the language used or the routing of the message in the receiving mobile. In this coding group, the maximum number of characters per page is 93 for default alphabet, 41 for UCS2 characters, and 82 for 8-bit data. Mobiles which have software complying with ETSI GSM phase 2 standards will be able to display only texts written with the default alphabet. Coding group 0101 is otherwise similar to coding group 0100 except that you can define the routing of the message in the receiving mobile. Mobiles which have software complying with ETSI GSM phase 2 standards will not be able to display messages belonging to this group.

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

15 (73)

EC - SMS Cell Broadcast Handling

Coding group 1111 is recommended when you want to send 8-bit data or messages written with the default alphabet and you do not want to define the language used. In this coding group, you can also define the routing of the message in the receiving mobile or leave the routing open. Mobiles which have software complying with ETSI GSM phase 2 standards will be able to display messages belonging to this group.
Chinese characters belong to the UCS2 character set. To be able to write, for example, Chinese characters you should use coding groups 0001, 0100, or 0101.

language identifier
GER ENG ITA FRE SPA DUT SWE DAN POR FIN NOR GRE TUR German English Italian French Spanish Dutch Swedish Danish Portuguese Finnish Norwegian Greek Turkish

The language identifier indicates the language of the short message. If the coding group is 0000, the parameter is obligatory. Otherwise this parameter will not be asked.

message class
The message class indicates where the mobile equipment (ME) will route the message. The ME user can override the defined default value of the routing. If the message identifier is from 0 to 999, the parameter can have the following values:

16 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECA CREATE MESSAGE WITH EDITOR

MC0 MC1 MC2 MC3

... ... ... ...

CLASS CLASS CLASS CLASS

0, 1, 2, 3,

DIRECT DISPLAY BY MS, NO MEMORY NEEDED DIRECT DISPLAY BY MS, MEMORY NEEDED SIM-SPECIFIC MESSAGE TE-SPECIFIC MESSAGE

In the above, the qualifier 'no memory needed' means that the MS will not store the received message in the ME or SIM. The qualifier 'memory needed', in contrast, means that the MS will store the received message in the ME or SIM. If the message identifier is from 4096 to 4351, the parameter can have only the following value:
MC2 ... CLASS 2, SIM-SPECIFIC MESSAGE

If the coding group is 0101 or 1111, the parameter is obligatory. Otherwise this parameter will not be asked.

alphabet identifier
The alphabet identifier indicates the character length used in the message coding. The default alphabet has 7 bits per character and it is defined in 3GPP TS 23.038. If the message identifier is in the range of 4096 to 4351 and the coding group is 1111, the parameter can have only the following value:
8BIT ... DATA

If the message identifier is in the range of 4096 to 4351 and the coding group is 0101, the parameter can have the following values:
8BIT ... DATA 16BIT ... DATA

If the message identifier is from 0 to 999, the following conditions apply: With coding group 0001 the parameter can have the following values:
7BIT ... DEFAULT ALPHABET 16BIT ... UCS2

With coding groups 0100 or 0101 the parameter can have the following values:
7BIT ... DEFAULT ALPHABET 8BIT ... DATA 16BIT ... UCS2

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

17 (73)

EC - SMS Cell Broadcast Handling

With coding group 1111 the parameter can have the following values:
7BIT 8BIT ... DEFAULT ALPHABET ... DATA

If the coding group is any of the above-mentioned coding groups, the parameter is obligatory. With coding group 0000 this parameter will not be asked.

repetition rate
The parameter indicates the repetition rate of the message. If the DRX option is in your software build, the value ranges from 1 to 9 and the values correspond to repetition rates of 4, 8, 15, 30, 60, 120, 241, 481, and 963 seconds (time rounded to the nearest second). Otherwise the value ranges from 0 to 9 and the values correspond to the repetition rates of 2, 4, 8, 15, 30, 60, 120, 241, 481, and 963 seconds. The parameter is obligatory. Examples 1. Create a message in which the message identifier is 100, message code is 20, geographical scope is location area wide, display mode is normal, coding group is 0000, and the language is English. The repetition rate of the message is 8. ZECA:100:20:3:1,ENG:3; 2. Create a message in which the message identifier is 34, message code is 10, geographical scope is cell wide, display mode is normal, coding group is 0001, and the used alphabet is UCS2 16-bit characters. The repetition rate of the message is 4. ZECA:34:10:4:2,16BIT:2:; 3. Create a message in which the message identifier is 234, message code is 20, geographical scope is location area wide, display mode is normal, coding group is 0101, message class is 2 (user-defined), and the alphabet is 8-bit user-defined characters. The repetition rate of the message is 8. ZECA:234:20:3:4,MC2,8BIT:3; 4. Create a message in which the message identifier is 4100, message code is 500, geographical scope is PLMN wide, display mode is normal, coding group is 1111, message class is 2 (no other option), and the used alphabet is UCS2 8-bit characters. The repetition rate of the message is 30. ZECA:4100:500:2:5,MC2,8BIT:4;

18 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECA CREATE MESSAGE WITH EDITOR

Additional information

To start a new line in the text that is displayed on the MS, you have to write two # characters into the text. These characters are then converted into <CR> by the MML. This is only possible when you are using the 7-bit default character set. All characters can be entered by using hexadecimal presentation. Hexadecimal presentation means that you write the hexadecimal code for the character that you want to be displayed by the ME. For 7- and 8-bit characters, the hexadecimal code is a two-figure number whereas the 16bit characters are represented by four numbers. When using the hexadecimal presentation in the text you write all numbers forming the character in question. For example, the dollar sign's ($) hexadecimal code is '2'. With 7- and 8-bit characters it is written in the text as +02 and with 16-bit characters as +0002. Correspondingly, if you want to write a + character into the text, you write two + characters which are then converted into one + character by the MML. This is only possible when you are using the 7-bit default alphabet. If you want to remove characters from the end of the text, you must go to the end of the text and change from overstrike mode to insert mode (ctrl A) and remove the text by using backspace. If the insert mode is not on when you do this, the text will be overwritten with the space character (20 H) and the message will consist of the remaining text and space characters. When using 16-bit characters (UCS2), all characters are written using the hexadecimal presentation. If you put keyboard characters in the text, the rest of the text will be illegible when displayed by ME.

Execution printouts

You can enter a new message to the edit space. The parameters of the message cannot be edited. If the parameters require editing you have to use the ECR command. The message index is given after the message has been stored. If you accept the message, the program displays the value of the message index. The execution printout of command example 1 is the following:

MESSAGE IDENTIFIER MESSAGE CODE GEOGRAPHICAL SCOPE CODING GROUP LANGUAGE REPETITION RATE

: 100 : 20 : LOCATION AREA WIDE, NORMAL : 0000 : ENGLISH : 8 1

MESSAGE IS STORED WITH MESSAGE INDEX

The execution printout of command example 2 is the following:

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

19 (73)

EC - SMS Cell Broadcast Handling

MESSAGE IDENTIFIER MESSAGE CODE GEOGRAPHICAL SCOPE CODING GROUP ALPHABET IDENTIFIER REPETITION RATE

: 34 : 10 : CELL WIDE, IMMEDIATE : 0001 : 16-BIT UCS2 CHARACTERS : 4 6

MESSAGE IS STORED WITH MESSAGE INDEX

The execution printout of command example 3 is the following:

MESSAGE IDENTIFIER MESSAGE CODE GEOGRAPHICAL SCOPE CODING GROUP MESSAGE CLASS ALPHABET IDENTIFIER REPETITION RATE : : : : : : : 234 20 LOCATION AREA WIDE, NORMAL 0101 2 8-BIT DATA/USER-DEFINED CHARACTERS 8 11

MESSAGE IS STORED WITH MESSAGE INDEX

The execution printout of command example 4 is the following:

MESSAGE IDENTIFIER MESSAGE CODE GEOGRAPHICAL SCOPE CODING GROUP MESSAGE CLASS ALPHABET IDENTIFIER REPETITION RATE : : : : : : : 4100 500 PLMN WIDE, NORMAL 1111 2 8-BIT DATA/USER-DEFINED CHARACTERS 30 11

MESSAGE IS STORED WITH MESSAGE INDEX

If you reject the message the program displays the following comment:
/*** INTERRUPT ***/

The MML exits the editor automatically when the editor's buffer is full (4185 characters). Note that the maximum length of the final message is 1395 characters. If the final message is longer than 1395, the rest of the characters are not stored:
/*** MAXIMUM LENGTH OF EDIT BUFFER HAS BEEN REACHED ***/

Semantic error messages Execution error messages

If an error occurs, the general semantic error messages of MML commands are output.

/* NOT ENOUGH SPACE FOR THE MESSAGE */

20 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECA CREATE MESSAGE WITH EDITOR

There is not enough space to store the short message.

/*** EXECUTION FAILED ***/ /*** TRY AGAIN ***/

The program cannot store the short message.

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

21 (73)

EC - SMS Cell Broadcast Handling

22 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECB CREATE/MODIFY MESSAGE TEXT PAGE BY PAGE

Function With the ECB command you create new cell broadcast messages when the ECA command cannot be used, and modify old cell broadcast messages when the ECM command cannot be used. message identifier: message code: geographical scope: coding group, language identifier, message class, alphabet identifier: repetition rate: message index: page;
ECB: < message identifier > : < message code > : < geographical scope > : < ( < < < coding group > , language identifier > | alphabet identifier > | message class > , < alphabet identifier > ) :

Parameters

Syntax

< repetition rate > : [ < message index > ] : < page > ;

Parameter explanations

message identifier
The value range is from 0 to 999 for short messages of all types, and from 4096 to 4351 for cell broadcast data download to the SIM messages. The parameter is obligatory.

message code

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

23 (73)

EC - SMS Cell Broadcast Handling

The value range is from 0 to 1023. The value is used for differentiating between messages which have the same message identifier and thus share the same source and type. The parameter is obligatory.

geographical scope
The geographical scope indicates the geographical area over which the message code is unique as well as the display mode of the mobile. The parameter can have the following values:
1 2 3 4 ... ... ... ... CELL WIDE, DISPLAY MODE IMMEDIATE PLMN WIDE, DISPLAY MODE NORMAL LOCATION AREA WIDE, DISPLAY MODE NORMAL CELL WIDE, DISPLAY MODE NORMAL

The parameter is obligatory.

24 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECB CREATE/MODIFY MESSAGE TEXT PAGE BY PAGE

The parameter is obligatory.

Coding group 0000 is the recommended choice for the coding group because it is understood by all mobiles that can receive cell broadcast messages. Earlier releases' messages belong to this coding group. In this coding group, you can choose the language from a list of 13 languages, the alphabet is automatically the default 7-bit alphabet, and there are 93 characters per page in a message. Coding group 0001 is recommended when you want to define the language of the message, but the language is not among the 13 languages defined in the coding group 0000. In this coding group, the twoletter language identifiers (which are defined in the ISO 639 standard) are written at the beginning of the message so that the first two letters are followed by <CR> = 0D H. You must also choose the alphabet used in the message. You can choose either the 7-bit default alphabet or the 16-bit UCS2 characters.

Note
The language identifier used in coding group 0001 must be written in lower case letters.

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

25 (73)

EC - SMS Cell Broadcast Handling

Coding group 0101 is otherwise similar to coding group 0100 except that you can define the routing of the message in the receiving mobile. Mobiles which have software complying with ETSI GSM phase 2 standards will not be able to display messages belonging to this group. Coding group 1111 is recommended when you want to send 8-bit data or messages written with the default alphabet and you do not want to define the language used. In this coding group, you can also define the routing of the message in the receiving mobile or leave the routing open. Mobiles which have software complying with ETSI GSM phase 2 standards will be able to display messages belonging to this group.
Chinese characters belong to the UCS2 character set. To be able to write, for example, Chinese characters you should use coding groups 0001, 0100, or 0101.

language identifier
GER ENG ITA FRE SPA DUT SWE DAN POR FIN NOR GRE TUR German English Italian French Spanish Dutch Swedish Danish Portuguese Finnish Norwegian Greek Turkish

The language identifier indicates the language of the short message. If the coding group is 0000, the parameter is obligatory. Otherwise this parameter will not be asked.

message class
The message class indicates where the mobile equipment (ME) will route the message. The ME user can override the defined default value of the routing.

26 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECB CREATE/MODIFY MESSAGE TEXT PAGE BY PAGE

If the message identifier is from 0 to 999, the parameter can have the following values:
MC0 MC1 MC2 MC3 ... ... ... ... CLASS CLASS CLASS CLASS 0, 1, 2, 3, DIRECT DISPLAY BY MS, NO MEMORY NEEDED DIRECT DISPLAY BY MS, MEMORY NEEDED SIM-SPECIFIC MESSAGE TE-SPECIFIC MESSAGE

In the above, the qualifier 'no memory needed' means that the MS will not store the received message in the ME or SIM. The qualifier 'memory needed', in contrast, means that the MS will store the received message in the ME or SIM. If the message identifier is in the range of 4096 to 4351, the parameter can have only the following value:
MC2 ... CLASS 2, SIM-SPECIFIC MESSAGE

If the coding group is 0101 or 1111, the parameter is obligatory. Otherwise this parameter will not be asked.

If the message identifier is in the range of 4096 to 4351 and the coding group is 0101, the parameter can have the following values:
8BIT ... DATA 16BIT ... DATA

If the message identifier is from 0 to 999, the following conditions apply: With coding group 0001 the parameter can have the following values:
7BIT ... DEFAULT ALPHABET 16BIT ... UCS2

With coding groups 0100 or 0101 the parameter can have the following values:

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

27 (73)

EC - SMS Cell Broadcast Handling

7BIT ... DEFAULT ALPHABET 8BIT ... DATA 16BIT ... UCS2

With coding group 1111 the parameter can have the following values:
7BIT 8BIT ... DEFAULT ALPHABET ... DATA

If the coding group is any of the above-mentioned coding groups, the parameter is obligatory. With coding group 0000 this parameter will not be asked.

message index
The value range is from 1 to 8068 for BSCi/BSC2i and from 1 to 15000 for BSC3i. If the message index is missing, a new message is created. Otherwise the index is used for finding the old message that will be modified.

page
A page parameter guide for characters with the 7-bit default alphabet:
/* IDENTIFY PAGE OF MESSAGE P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 .... .... .... .... .... .... .... .... .... .... .... .... .... PAGE PAGE PAGE PAGE PAGE PAGE PAGE PAGE PAGE PAGE PAGE PAGE PAGE NUMBER NUMBER NUMBER NUMBER NUMBER NUMBER NUMBER NUMBER NUMBER NUMBER NUMBER NUMBER NUMBER 1 2 3 4 5 6 7 8 9 10 11 12 13

28 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECB CREATE/MODIFY MESSAGE TEXT PAGE BY PAGE

P14 .... PAGE NUMBER 14 P15 .... PAGE NUMBER 15 ONE OF PAGES IS OBLIGATORY */

A page parameter guide for 8-bit characters:

/* IDENTIFY PAGE OF MESSAGE P1A P1B P1C P2A P2B P2C P3A P3B P3C P4A P4B P4C P5A P5B P5C P6A P6B P6C P7A P7B P7C P8A P8B P8C .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... FIRST PART OF PAGE 1 SECOND PART OF PAGE 1 THIRD PART OF PAGE 1 FIRST PART OF PAGE 2 SECOND PART OF PAGE 2 THIRD PART OF PAGE 2 FIRST PART OF PAGE 3 SECOND PART OF PAGE 3 THIRD PART OF PAGE 3 FIRST PART OF PAGE 4 SECOND PART OF PAGE 4 THIRD PART OF PAGE 4 FIRST PART OF PAGE 5 SECOND PART OF PAGE 5 THIRD PART OF PAGE 5 FIRST PART OF PAGE 6 SECOND PART OF PAGE 6 THIRD PART OF PAGE 6 FIRST PART OF PAGE 7 SECOND PART OF PAGE 7 THIRD PART OF PAGE 7 FIRST PART OF PAGE 8 SECOND PART OF PAGE 8 THIRD PART OF PAGE 8 P9A P9B P9C P10A P10B P10C P11A P11B P11C P12A P12B P12C P13A P13B P13C P14A P14B P14C P15A P15B P15C .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... FIRST PART OF PAGE 9 SECOND PART OF PAGE 9 THIRD PART OF PAGE 9 FIRST PART OF PAGE 10 SECOND PART OF PAGE 10 THIRD PART OF PAGE 10 FIRST PART OF PAGE 11 SECOND PART OF PAGE 11 THIRD PART OF PAGE 11 FIRST PART OF PAGE 12 SECOND PART OF PAGE 12 THIRD PART OF PAGE 12 FIRST PART OF PAGE 13 SECOND PART OF PAGE 13 THIRD PART OF PAGE 13 FIRST PART OF PAGE 14 SECOND PART OF PAGE 14 THIRD PART OF PAGE 14 FIRST PART OF PAGE 15 SECOND PART OF PAGE 15 THIRD PART OF PAGE 15

ONE OF PAGES IS OBLIGATORY

A page parameter guide for 16-bit characters:

/* IDENTIFY PAGE OF MESSAGE P1A P1B P2A P2B P3A P3B P4A P4B P5A P5B P6A P6B P7A P7B P8A .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... FIRST PART OF PAGE 1 SECOND PART OF PAGE 1 FIRST PART OF PAGE 2 SECOND PART OF PAGE 2 FIRST PART OF PAGE 3 SECOND PART OF PAGE 3 FIRST PART OF PAGE 4 SECOND PART OF PAGE 4 FIRST PART OF PAGE 5 SECOND PART OF PAGE 5 FIRST PART OF PAGE 6 SECOND PART OF PAGE 6 FIRST PART OF PAGE 7 SECOND PART OF PAGE 7 FIRST PART OF PAGE 8

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

29 (73)

EC - SMS Cell Broadcast Handling

P8B P9A P9B P10A P10B P11A P11B P12A P12B P13A P13B P14A P14B P15A P15B

.... .... .... .... .... .... .... .... .... .... .... .... .... .... ....

SECOND PART OF PAGE 8 FIRST PART OF PAGE 9 SECOND PART OF PAGE 9 FIRST PART OF PAGE 10 SECOND PART OF PAGE 10 FIRST PART OF PAGE 11 SECOND PART OF PAGE 11 FIRST PART OF PAGE 12 SECOND PART OF PAGE 12 FIRST PART OF PAGE 13 SECOND PART OF PAGE 13 FIRST PART OF PAGE 14 SECOND PART OF PAGE 14 FIRST PART OF PAGE 15 SECOND PART OF PAGE 15 */

ONE OF PAGES IS OBLIGATORY

The page indicates the page of the message that will be inserted or modified. If the page parameter is given but the text is missing, the page is filled with carriage returns. If 8-bit characters have been chosen, you can write 36 characters to the first and second parts of a page, and the remaining 10 characters to the third and last part of the page. An example of a page guide for 8-bit characters, first part:
/* ENTER TEXT OF FIRST PART OF PAGE x MAX NUMBER OF CHARACTERS: 36 8-BIT CHARACTERS (108 CHARACTERS) */

An example of a page guide for 8-bit characters, second part:

/* ENTER TEXT OF SECOND PART OF PAGE x MAX NUMBER OF CHARACTERS: 36 8-BIT CHARACTERS (108 CHARACTERS) */

An example of a page guide for 8-bit characters, third part:

/* ENTER TEXT OF THIRD PART OF PAGE x

MAX NUMBER OF CHARACTERS: 10 8-BIT CHARACTERS (27 CHARACTERS) */

30 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECB CREATE/MODIFY MESSAGE TEXT PAGE BY PAGE

If 16-bit characters have been chosen, you can write 22 characters to the first part of the page and the remaining 19 characters to the second and last part of the page. An example of a page guide for 16-bit characters, first part:
/* ENTER TEXT OF FIRST PART OF PAGE x MAX NUMBER OF CHARACTERS: 22 16-BIT CHARACTERS (110 CHARACTERS) */

An example of a page guide for 16-bit characters, second part:

/* ENTER TEXT OF SECOND PART OF PAGE x MAX NUMBER OF CHARACTERS: 19 16-BIT CHARACTERS (95 CHARACTERS) */

If 16-bit characters and coding group 0001 have been chosen, you can write to the first part of page 1 (P1A) the language identifier and 21 characters, and to the second and last part of page 1 (P1B) the remaining 19 characters. All other pages will be written as has been explained above. An example of a page guide for 16-bit characters, coding group 0001, first part of page 1:
/* ENTER TEXT OF FIRST PART OF PAGE 1 MAX NUMBER OF CHARACTERS: LANGUAGE IDENTIFIER (2 CHARACTERS) + 21 16-BIT CHARACTERS (105 CHARACTERS) */

An example of a page guide for 16-bit characters, second part:

/* ENTER TEXT OF SECOND PART OF PAGE 1 MAX NUMBER OF CHARACTERS: 19 16-BIT CHARACTERS (95 CHARACTERS) */

One of the pages is obligatory.

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

31 (73)

EC - SMS Cell Broadcast Handling

Examples

Create a message in which the message identifier is 100, message code is 20, geographical scope is location area wide, display mode is normal, coding group is 0000 and the language is English. The repetition rate of the message is 8. ZECB:100:20:3:1,ENG:3::P1=+00TEST##MESSAGE;

Create a message in which the message identifier is 34, message code is 10, geographical scope is cell wide, display mode is normal, coding group is 0001, and the used alphabet is UCS2 16-bit characters. The repetition rate of the message is 4. ZECB:34:10:4:2,16BIT:2:6:P1A=EN+004D+0045+0053 +0053+0041+0047+0045+0020+0057 +0052+0049+0054 +0045+004E+0020+0057+0049+0054+0048+0020+0055;

Add the rest of the first page's text to the message created in the previous example. ZECB:34:10:4:2,16BIT:2:6:P1B=+0043+0053+0032+002D +0043+0048+0041+0052+0041 +0043+0054+0045+0052 +0053+0020+0046+0055+004C+004C;

Add the second page of the message with message index 7 (that is, the message modified in the previous example). ZECB:34:10:4:2,16BIT:2:6:P2A=+0050+0041+0047+0045 +0020+0032+002E;

Create a message in which the message identifier is 50, message code is 10, geographical scope is location area wide, display mode is normal, coding group is 0100, and the used alphabet is UCS2 16bit characters. The repetition rate of the message is 4. ZECB:50:10:3:3,16BIT:2:9:P1A=+004D+0045+0053+0053 +0041+0047+0045+0020+0057 +0052+0049+0054+0045 +004E+0020+0057+0049+0054+0048+0020+0055+0043;

Add the rest of the first page's text to the message created in the previous example. ZECB:50:10:4:3,16BIT:2:9:P1B=+0053+0032+002D+0043 +0048+0041+0052+0041+0043 +0054+0045+0052+0053 +0020+0046+0055+004C+004C+002E;

Create a message in which the message identifier is 234, message code is 20, geographical scope is location area wide, display mode is normal, coding group is 0101, message class is 2 (user-defined), and the alphabet is 8-bit data or user-defined characters. The repetition rate of the message is 15.

32 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECB CREATE/MODIFY MESSAGE TEXT PAGE BY PAGE

ZECB:234:20:3:4,MC2,8BIT:4::P1A=+01+02+03+04+05+06 +07+08+09+0A+0B+0C+0D+0E +0F+10+11+12+13+14+15+16 +17+18+19+1A+1B+1C+1D+1E+1F+20+21+22+23+24; 8. Add the second part of the first page to the message created in the previous example. ZECB:234:20:3:4,MC2,8BIT:4::P1B=+25+26+27+28+29+2A +2B+2C+2D+2E+2F+30+31+32 +33+34+35+36+37+38+39+3A +3B+3C+3D+3E+3F+40+41+42+43+44+45+46+47+48; 9. Add the third part of the first page to the message modified in the previous example to make the first page full. ZECB:234:20:3:4,MC2,8BIT:4::P1C=+49+4A+4B+4C+4D+4E +4F+50+51; Additional information To start a new line in the text that is displayed on the MS, you have to write two # characters to that place in the text. These characters are then converted into <CR> by the MML program. This is only possible when you are using 7-bit default character set. All characters can be entered by using hexadecimal presentation. Hexadecimal presentation means that you write the hexadecimal code for the character you want to be displayed by the ME. For 7- and 8-bit characters, the hexadecimal code is a two-figure number whereas the 16bit characters are represented by four numbers. When using the hexadecimal presentation in the text you write all numbers forming the character in question. For example the dollar sign's ($) hexadecimal code is '2'. With 7- and 8-bit characters it will be written in the text as +02 and with 16-bit characters as +0002. Correspondingly, if you want to write a + character in the text, you write two + characters which are then converted into one + character by the MML program. This also is possible only with 7-bit characters. If you want to remove or add characters to the middle of the text, you have to change from overstrike mode to write mode (ctrl - A). When using 16-bit characters (UCS2), all characters are written using the hexadecimal presentation. If you put keyboard characters in the text, the rest of the text will be illegible when displayed by the ME.

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

33 (73)

EC - SMS Cell Broadcast Handling

Note
This command can only be used for creating and modifying message text, or inserting pages to the messages page by page. It is not possible to remove pages by using this command. If you want to change the message parameters, use the ECR command.

Execution printouts
MESSAGE IDENTIFIER MESSAGE CODE GEOGRAPHICAL SCOPE CODING GROUP LANGUAGE REPETITION RATE

The execution printout of command example 1 is the following:

: 100 : 20 : LOCATION AREA WIDE, NORMAL : 0000 : ENGLISH : 8 8

MESSAGE IS STORED WITH MESSAGE INDEX

The execution printout of command example 3 is the following:

MESSAGE IS STORED WITH MESSAGE INDEX 7

The execution printout of command example 4 is the following:

MESSAGE IS STORED WITH MESSAGE INDEX 11

The execution printout of command example 5 is the following:

MESSAGE IDENTIFIER MESSAGE CODE GEOGRAPHICAL SCOPE CODING GROUP ALPHABET IDENTIFIER REPETITION RATE : 50 : 10 : LOCATION AREA WIDE, NORMAL : 0100 : 16-BIT UCS2 CHARACTERS : 4 9

MESSAGE IS STORED WITH MESSAGE INDEX

The execution printout of command example 6 is the following:

MESSAGE IS STORED WITH MESSAGE INDEX 13

The execution printout of command example 7 is the following:

MESSAGE IDENTIFIER MESSAGE CODE GEOGRAPHICAL SCOPE CODING GROUP MESSAGE CLASS : 234 : 20 : LOCATION AREA WIDE, NORMAL : 1111 : 2

34 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECB CREATE/MODIFY MESSAGE TEXT PAGE BY PAGE

ALPHABET IDENTIFIER : 8-BIT DATA/USER-DEFINED CHARACTERS REPETITION RATE : 15 MESSAGE IS STORED WITH MESSAGE INDEX 1

The execution printout of command example 8 is the following:

MESSAGE IS STORED WITH MESSAGE INDEX 2

The execution printout of command example 9 is the following:

MESSAGE IS STORED WITH MESSAGE INDEX 3

Semantic error messages Execution error messages

If an error occurs, the general semantic error messages of MML commands are output.

/* CB MESSAGE NOT DEACTIVATED */

The short message has to be deactivated completely before modifying.

/*** CB MESSAGE NOT EXISTENT ***/

The program has not found the short message to be modified.

/*** NOT ENOUGH SPACE FOR THE MESSAGE ***/

There is not enough space to store the short message.

/*** ILLEGAL ALPHABET IDENTIFIER CHANGE IN MODIFICATION ***/

The given alphabet identifier is different from the one used in the previous storing of this particular message. This would most likely cause the text of the short message service cell broadcast (SMSCB) message to become distorted.
/*** ILLEGAL CODING GROUP CHANGE IN MODIFICATION ***/

The given coding group is different from the original coding group. This would cause the text of this 16-bit SMSCB message to become distorted. In practise this means that the message originally with coding group 0001 has been given either coding group 0100 or 0101, or the message originally with coding group 0100 or 0101 has been given the coding group 0001.
/*** EXECUTION FAILED ***/ /*** TRY AGAIN ***/

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

35 (73)

EC - SMS Cell Broadcast Handling

The program cannot store the short message.

36 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECM MODIFY MESSAGE WITH EDITOR

Function Parameters Syntax Parameter explanations With the ECM command you modify the text of an existing inactive cell broadcast message. message index;
ECM: <message index> ;

message index
The value range is from 1 to 8068 for BSCi/BSC2i and from 1 to 15000 for BSC3i. The message index value is used for finding the message to be edited. The parameter is obligatory.

Examples

Find message with message index 15 for editing. ZECM:15;

Find message with message index 1 for editing. ZECM:1;

Find message with message index 11 for editing. ZECM:11;

Additional information

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

37 (73)

EC - SMS Cell Broadcast Handling

hexadecimal presentation in the text you write all numbers forming the character in question. For example, the dollar sign's ($) hexadecimal code is '2'. With 7- and 8-bit characters it is written in the text as +02 and with 16-bit characters as +0002. Correspondingly, if you want to write a + character into the text, you write two + characters which are then converted into one + character by the MML. This is only possible when you are using the 7-bit default alphabet. If you want to remove characters from the end of the text, you must go to the end of the text and change from overstrike mode to insert mode (ctrl A) and remove the text by using backspace. If the insert mode is not on when you do this, the text will be overwritten with the space character (20 H) and the message will consist of the remaining text and space characters. When using 16-bit characters (UCS2), all characters are written using the hexadecimal presentation. If you put keyboard characters in the text, the rest of the text will be illegible when displayed by ME. Execution printouts
OLD MESSAGE INDEX MESSAGE IDENTIFIER MESSAGE CODE GEOGRAPHICAL SCOPE CODING GROUP LANGUAGE REPETITION RATE

The execution printout of command example 1 is the following:

: 15 : 100 : 20 : LOCATION AREA WIDE, NORMAL : 0000 : ENGLISH : 16 8

MESSAGE IS STORED WITH MESSAGE INDEX

The execution printout of command example 2 is the following:

OLD MESSAGE INDEX MESSAGE IDENTIFIER MESSAGE CODE GEOGRAPHICAL SCOPE CODING GROUP ALPHABET IDENTIFIER REPETITION RATE : 1 : 34 : 10 : CELL WIDE, IMMEDIATE : 0001 : 16-BIT UCS2 CHARACTERS : 8 10

MESSAGE IS STORED WITH MESSAGE INDEX

The execution printout of command example 3 is the following:

38 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECM MODIFY MESSAGE WITH EDITOR

OLD MESSAGE INDEX MESSAGE IDENTIFIER MESSAGE CODE GEOGRAPHICAL SCOPE CODING GROUP MESSAGE CLASS ALPHABET IDENTIFIER REPETITION RATE

: 11 : 234 : 20 : LOCATION AREA WIDE, NORMAL : 1111 : 2 : 8-BIT DATA/USER-DEFINED CHARACTERS : 16 18

MESSAGE IS STORED WITH MESSAGE INDEX

If you reject the message the program displays the following comment:
/*** INTERRUPT ***/

Semantic error messages Execution error messages

If an error occurs, the general semantic error messages of MML commands are output.

/* CB MESSAGE NOT DEACTIVATED */

The short message has to be deactivated completely before editing.

/*** CB MESSAGE NOT EXISTENT ***/

The program has not found the short message to be modified.

/*** NOT ENOUGH SPACE FOR THE MESSAGE ***/

There is not enough space to store the short message.

/*** EXECUTION FAILED ***/ /*** TRY AGAIN ***/

The program cannot store the short message.

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

39 (73)

EC - SMS Cell Broadcast Handling

40 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECR MODIFY MESSAGE PARAMETERS

Function Parameters With the ECR command you modify the parameters of an existing inactive cell broadcast message. message index: new message identifier: new message code: new geographical scope: new coding group, new language identifier, new message class, new alphabet identifier: new repetition rate;
ECR: < message index > : < new message identifier > : < new message code > : < new geographical scope > : < (< < < new new new new coding group > , language identifier > | alphabet identifier > | message class > , < new alphabet identifier >) :

Syntax

< new repetition rate > ;

Parameter explanations

message index
The value range is from 1 to 8068 for BSCi/BSC2i and from 1 to 15000 for BSC3i. The value indicates the message whose parameters are to be edited. The parameter is obligatory.

new message identifier

The value range is from 0 to 999 for short messages of all types, and from 4096 to 4351 for cell broadcast data download to the SIM messages. The parameter is obligatory.

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

41 (73)

EC - SMS Cell Broadcast Handling

new message code

The value range is from 0 to 1023. The value is used for differentiating between messages which have the same message identifier and thus share the same source and type. The parameter is obligatory.

new geographical scope

The parameter is obligatory.

new coding group

The coding group indicates the data coding scheme used to indicate the intended handling of the message at the MS, the alphabet/coding, and the language (when applicable). The coding groups of the cell broadcast data coding scheme are defined in 3GPP TS 23.038. If the message identifier is from 0 to 999, the parameter can have the following values:
1 ... GROUP 0000: DEFAULT ALPHABET, SELECT LANGUAGE 2 ... GROUP 0001: DEFAULT ALPHABET/UCS2 TEXT, MESSAGE PRECEDED BY LANGUAGE IDENTIFICATION 3 ... GROUP 0100: UNCOMPRESSED 8-BIT DATA OR DEFAULT ALPHABET/UCS2 TEXT, NO MESSAGE CLASS 4 ... GROUP 0101: UNCOMPRESSED 8-BIT DATA OR DEFAULT ALPHABET/UCS2 TEXT, WITH MESSAGE CLASS 5 ... GROUP 1111: 8-BIT DATA OR DEFAULT ALPHABET TEXT, MESSAGE CLASS

If the message identifier is in the range of 4096 to 4351, the parameter can have the following values:

42 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECR MODIFY MESSAGE PARAMETERS

4 ... GROUP 0101: UNCOMPRESSED 8-BIT DATA OR DEFAULT ALPHABET/UCS2 TEXT, WITH MESSAGE CLASS 5 ... GROUP 1111: 8-BIT DATA OR DEFAULT ALPHABET TEXT, MESSAGE CLASS

The parameter is obligatory.

Coding group 0000 is the recommended choice for the coding group because it is understood by all mobiles that can receive cell broadcast messages. Earlier releases' messages belong to this coding group. In this coding group, you can choose the language from a list of 13 languages, the alphabet is automatically the default 7-bit alphabet, and there are 93 characters per page in a message. Coding group 0001 is recommended when you want to define the language of the message, but the language is not among the 13 languages defined in the coding group 0000. In this coding group, the twoletter language identifiers (which are defined in the ISO 639 standard) are written at the beginning of the message so that the first two letters are followed by <CR> = 0D H. You must also choose the alphabet used in the message. You can choose either the 7-bit default alphabet or the 16-bit UCS2 characters.

Note
The language identifier used in coding group 0001 must be written in lower case letters.

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

43 (73)

EC - SMS Cell Broadcast Handling

group, the maximum number of characters per page is 93 for default alphabet, 41 for UCS2 characters, and 82 for 8-bit data. Mobiles which have software complying with ETSI GSM phase 2 standards will be able to display only texts written with the default alphabet.

new language identifier

GER ENG ITA FRE SPA DUT SWE DAN POR FIN NOR GRE TUR German English Italian French Spanish Dutch Swedish Danish Portuguese Finnish Norwegian Greek Turkish

The language identifier indicates the language of the short message. If the coding group is 0000, the parameter is obligatory. Otherwise this parameter will not be asked.

new message class

44 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECR MODIFY MESSAGE PARAMETERS

The message class indicates where the mobile equipment (ME) will route the message. The ME user can override the defined default value of the routing. If the message identifier is from 0 to 999, the parameter can have the following values:
MC0 MC1 MC2 MC3 ... ... ... ... CLASS CLASS CLASS CLASS 0, 1, 2, 3, DIRECT DISPLAY BY MS, NO MEMORY NEEDED DIRECT DISPLAY BY MS, MEMORY NEEDED SIM-SPECIFIC MESSAGE TE-SPECIFIC MESSAGE

In the above, the qualifier 'no memory needed' means that the MS will not store the received message in the ME or SIM. The qualifier 'memory needed', in contrast, means that the MS will store the received message in the ME or SIM. If the message identifier is in the range of 4096 to 4351, the parameter can only have the following value:
MC2 ... CLASS 2, SIM-SPECIFIC MESSAGE

If the coding group is 0101 or 1111, the parameter is obligatory. Otherwise this parameter will not be asked.

new alphabet identifier

The alphabet identifier indicates the character length used in the message coding. The default alphabet has 7 bits per character and it is defined in 3GPP TS 23.038. If the message identifier is in the range of 4096 to 4351 and the coding group is 1111, the parameter can only have the following value:
8BIT ... DATA

If the message identifier is in the range of 4096 to 4351 and the coding group is 0101, the parameter can have the following values:
8BIT ... DATA 16BIT ... DATA

If the message identifier is from 0 to 999, the following conditions apply: With coding group 0001 the parameter can have the following values:
7BIT ... DEFAULT ALPHABET 16BIT ... UCS2

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

45 (73)

EC - SMS Cell Broadcast Handling

With coding groups 0100 or 0101 the parameter can have the following values:
7BIT ... DEFAULT ALPHABET 8BIT ... DATA 16BIT ... UCS2

With coding group 1111 the parameter can have the following values:
7BIT 8BIT ... DEFAULT ALPHABET ... DATA

If the coding group is any of the above-mentioned coding groups, the parameter is obligatory. With coding group 0000 this parameter will not be asked.

new repetition rate

The parameter indicates the repetition rate of the message. If the DRX option is in your software build, the value ranges from 1 to 9 and the values correspond to repetition rates of 4, 8, 15, 30, 60, 120, 241, 481, and 963 seconds (time rounded to the nearest second). Otherwise the value ranges from 0 to 9 and the values correspond to the repetition rates of 2, 4, 8, 15, 30, 60, 120, 241, 481, and 963 seconds. The parameter is obligatory. Examples 1. Modify message with message index 11 into a message which has message identifier 34, message code 10, and whose geographical scope is location area wide, display mode is normal, coding group is 0001, and the used alphabet is UCS2 16-bit characters. The repetition rate of the message is 15. ZECR:11:34:10:3:2,16BIT:3; 2. Modify message with message index 8 into a message which has message identifier 999, message code 15, and whose geographical scope is cell wide, display mode is normal, coding group is 0000, and the language is Finnish. The repetition rate of the message is 8. ZECR:8:999:15:4:1,FIN:2:; Additional information There are some limitations to parameter modification. The program will NOT implement these limitations but you should be aware of them. Do not change the alphabet used for the message. If you change the alphabet, the text will either disappear or become totally unreadable.

46 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECR MODIFY MESSAGE PARAMETERS

Changing the coding group of the message is also a sensitive operation. You should first check if the new coding group will support the alphabet used in the message and if it does, you should be extra careful if the alphabet used is UCS2 (16 bit). This is because the text will disappear if you change the coding group from 0100 or 0101 to 0001, and vice versa. With UCS2, the only 'allowed' coding group changes are from 0100 to 0101 and from 0101 to 0100. Execution printouts The execution printout of command example 1 is the following:

THE MESSAGE IS STORED WITH A NEW MESSAGE INDEX 15

The parameters of the message are stored completely. Semantic error messages Execution error messages
/*** CB MESSAGE NOT DEACTIVATED ***/

If an error occurs, the general semantic error messages of MML commands are output.

The short message has to be deactivated completely before editing.

/*** CB MESSAGE NOT EXISTENT ***/

The program has not found the short message to be modified.

/*** NOT ENOUGH SPACE FOR THE MESSAGE ***/

There is not enough space to store the short message.

/*** ILLEGAL ALPHABET IDENTIFIER CHANGE IN MODIFICATION ***/

The given alphabet identifier is different from the one used in the previous storing of this particular message and would most likely cause the text of the SMSCB (short message service cell broadcast) message to become distorted.
/*** ILLEGAL CODING GROUP CHANGE IN MODIFICATION ***/

The given coding group is different from the original coding group and would cause the text of this 16-bit SMSCB message to become distorted. In other words, the message originally with coding group 0001 has been given either coding group 0100 or 0101, or the message originally with coding group 0100 or 0101 has been given coding group 0001.

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

47 (73)

EC - SMS Cell Broadcast Handling

/* EXECUTION FAILED / / TRY AGAIN */

The program cannot store the short message.

48 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECS ACTIVATE MESSAGE

Function Parameters Syntax With the ECS command you activate an existing message for broadcasting within a certain BTS or BTSs. message index: BTS identification, BTS name;
ESC: < message index > : ( BTS = < BTS identification >...| < all > | NAME= < BTS name >... ) ;

Parameter explanations

message index
The value range is from 1 to 8068 for BSCi/BSC2i and from 1 to 15000 for BSC3i. The value is used for finding the message to be activated. The parameter is obligatory.

BTS identification
BTS = decimal The value indicates the BTSs that are to be activated for the message. Possible values range from 1 to 2000 (with maximum configuration). Value 0 activates all BTSs for the message. The characters & and && can be used. If the parameter NAME is given, the parameter BTS cannot be specified.

BTS name
NAME = text string

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

49 (73)

EC - SMS Cell Broadcast Handling

The name identifies the base transceiver station. The name can contain 1 15 characters. Several names can be given at the same time by using the character &. If the parameter BTS is given, the parameter NAME cannot be specified. Examples 1. Activate message with message index 12 for BTSs CENTRUM1 and LONDON1. ZECS:12:NAME=CENTRUM1&LONDON1; 2. Activate message with message index 1045 for all BTSs. ZECS:1045:BTS=0; 3. Activate message with message index 15 for BTSs 40, 41, 42, 43, 44, 45, and 50. ZECS:15:BTS=40&&45&50; Additional information If the DRX option is switched on, the schedule messages consume a part of the capacity of the cell broadcast channel (CBCH). For that reason, certain combinations of the respective repetition rates of the activated cell broadcast messages are no longer possible. The activation will become valid in the next schedule period and this will cause a one-minute delay at the maximum. If several activations to the same BTS take place during the same delay time, all activations will become valid at the same time.

Note
In order to have the cell broadcast messages broadcast, the cell broadcast channel must be determined with the ER command class (see Transceiver Handling) and the short message service cell broadcast (SMSCB) facility switched on with the EQ command class (see Base Transceiver Station Handling in BSC).

Execution printouts

If no BTSs have been created, the execution printout of command example 2 is the following:

* NO BTS CREATED * COMMAND EXECUTED

If not all the possible BTSs have been created, the execution printout of command example 2 is the following:

50 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECS ACTIVATE MESSAGE

MESSAGE NO. BTS NO. BTS1 BTS2 BTS3 BTS- 10 BTS- 11 BTS- 12 BTS- 13 BTS- 14 BTS- 15 BTS- 16 BTS- 17 BTS- 40 BTS- 41 BTS- 43 BTS- 44 BTS- 45 BTS- 46 BTS- 47 BTS- 48 BTS- 49 BTS- 50

1045 ACTIVATION STATE OK MESSAGE ALREADY ACTIVATED CELL BROADCAST NOT SUPPORTED OK OK MESSAGE ALREADY ACTIVATED MESSAGE ALREADY ACTIVATED OK OK CELL BROADCAST NOT OPERATIONAL CELL BROADCAST NOT OPERATIONAL CELL BROADCAST NOT SUPPORTED MESSAGE ALREADY ACTIVATED TOTAL LOAD OF BTS EXCEEDS 100% ERROR IN ACTIVATION NO SYSTEM BUFFER AVAILABLE MESSAGE REFERENCE IS ALREADY USED MESSAGE REFERENCE IS ALREADY USED MESSAGE ALREADY ACTIVATED OK ACTIVE CB MESSAGE CAPACITY PER BTS EXCEEDED

BTS NAME MAKKYLA1 LEPPAVAARA1 LEPPAVAARA2 PITAJANMAKI HELSINKI2 HELSINKI3 HELSINKI5 HELSINKI6 HELSINKI7 HELSINKI8 HELSINKI9 MAKKYLA LEPPAVAARA PITAJANMAKI HELSINKI1 HELSINKI4 MAKKYLA2 MAKKYLA3 MAKKYLA4 MAKKYLA5 HELSINKI6

* REST OF THE BTS NOT CREATED * COMMAND EXECUTED

The text CELL BROADCAST NOT OPERATIONAL means that the BTS in question cannot send any cell broadcast messages due to a blocked CBCH TRX. The text CELL BROADCAST NOT SUPPORTED means that the cell broadcast facility is not switched on in the BTS in question. The text MESSAGE REFERENCE IS ALREADY USED means that there is already in the BSC memory an active message for this particular BTS having the same message identifier, message code, and geographical scope. The execution printout of command example 3 is the following:
MESSAGE NO. BTS NO. BTS 40 BTS- 41 BTS- 42 BTS- 43 BTS- 44 BTS- 45 15 ACTIVATION STATE OK MESSAGE ALREADY ACTIVATED BTS NOT EXISTENT TOTAL LOAD OF BTS EXCEEDS 100% ERROR IN ACTIVATION NO SYSTEM BUFFER AVAILABLE

BTS NAME MAKKYLA LEPPAVAARA PITAJANMAKI HELSINKI1 HELSINKI4

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

51 (73)

EC - SMS Cell Broadcast Handling

BTS-

HELSINKI6

ACTIVE CB MESSAGE CAPACITY PER BTS EXCEEDED

COMMAND EXECUTED

The STATE column shows the acknowledgement choices. Semantic error messages Execution error messages
/*** CB MESSAGE NOT EXISTENT ***/

If an error occurs, the general semantic error messages of MML commands are output.

The program has not found the message to be activated. See also Execution printouts.

52 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECE DEACTIVATE MESSAGE

Function Parameters Syntax With the ECE command you deactivate an existing message. After deactivation, the message is no longer broadcast within a BTS or BTSs. message index: BTS identification, BTS name;
ECE: < message index > : ( BTS = < BTS identification > ... | < all > | name= < BTS name > ... ) ;

Parameter explanations

message index
The value range is from 1 to 8068 for BSCi/BSC2i and from 1 to 15000 for BSC3i. The value is used for finding the message to be deactivated. The parameter is obligatory.

BTS identification
BTS = decimal The value indicates the BTSs where the message is to be deactivated. Possible values range from 1 to 2000 (with maximum configuration). Value 0 deactivates the message in all BTSs. The characters & and && can be used. If the parameter NAME is given, the parameter BTS cannot be specified.

BTS name
NAME = text string

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

53 (73)

EC - SMS Cell Broadcast Handling

The name identifies the base transceiver station. The name can contain 1 15 characters. Several names can be given at the same time by using the character &. If the parameter BTS is given, the parameter NAME cannot be specified. Examples 1. Deactivate message with message index 12 in BTS HELSINKI1 and KILO. ZECE:12:NAME=HELSINKI1&KILO; 2. Deactivate message with message index 1045 in all BTSs. ZECE:1045:BTS=0; 3. Deactivate message with message index 530 in BTSs 40, 41, 42, 45, and 50. ZECE:530:BTS=40&&42&45&50; Additional information The deactivation will become valid in the next schedule period and this will cause a one-minute delay at the maximum. If several deactivations to the same BTS take place during the same delay time, all deactivations will become valid at the same time. If no BTSs have been created, the execution printout of command example 2 is the following:

Execution printouts

* NO BTS CREATED * COMMAND EXECUTED

If not all the possible BTSs have been created, the execution printout of command example 2 is the following:
MESSAGE NO. BTS NO. BTS1 BTS2 BTS3 BTS- 10 BTS- 11 BTS- 12 BTS- 13 BTS- 14 BTS- 15 BTS- 16 BTS- 17 BTS- 40 BTS- 41 BTS- 43 BTS- 44 1045 DEACTIVATION STATE OK MESSAGE OK OK OK MESSAGE MESSAGE OK OK OK OK OK MESSAGE OK OK

BTS NAME MAKKYLA1 LEPPAVAARA1 LEPPAVAARA2 PITAJANMAKI HELSINKI2 HELSINKI3 HELSINKI5 HELSINKI6 HELSINKI7 HELSINKI8 HELSINKI9 MAKKYLA LEPPAVAARA PITAJANMAKI HELSINKI1

ALREADY DEACTIVATED

ALREADY DEACTIVATED ALREADY DEACTIVATED

ALREADY DEACTIVATED

54 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECE DEACTIVATE MESSAGE

BTSBTSBTSBTSBTSBTS-

45 46 47 48 49 50

HELSINKI4 MAKKYLA2 MAKKYLA3 MAKKYLA4 MAKKYLA5 HELSINKI6

NO SYSTEM BUFFER AVAILABLE OK OK MESSAGE ALREADY DEACTIVATED OK ERROR IN DEACTIVATION

* REST OF THE BTS NOT CREATED * COMMAND EXECUTED

The execution printout of command example 3 is the following:

MESSAGE NO. BTS NO. BTS- 40 BTS- 41 BTS- 42 BTS- 45 BTS- 50 530 DEACTIVATION STATE OK MESSAGE ALREADY DEACTIVATED BTS NOT EXISTENT NO SYSTEM BUFFER AVAILABLE ERROR IN DEACTIVATION

BTS NAME MAKKYLA LEPPAVAARA HELSINKI4 HELSINKI6

COMMAND EXECUTED

The STATE column shows the acknowledgement choices. Semantic error messages Execution error messages
/*** CB MESSAGE NOT EXISTENT ***/

If an error occurs, the general semantic error messages of MML commands are used.

The program has not found the message to be deactivated. See also Execution printouts.

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

55 (73)

EC - SMS Cell Broadcast Handling

56 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECC DEACTIVATE BTS(S)

Function Parameters Syntax With the ECC command you deactivate a BTS or BTSs. All active messages within that particular BTS or BTSs are deactivated. BTS identification, BTS name;
ECC: ( BTS = < BTS identification > ... | < all > | NAME = < BTS name > ... ) ;

Parameter explanations

BTS identification
BTS = decimal The value identifies the BTSs that are to be deactivated for short messages. Possible values range from 1 to 2000 (with maximum configuration). Value 0 deactivates all messages within all BTSs. The characters & and && can be used. If the parameter NAME is given, the parameter BTS cannot be specified.

BTS name
NAME = text string The name identifies the base transceiver station. The name can contain 1 to 15 characters. Several names can be given at the same time by using the character &. If the parameter BTS is given, the parameter NAME cannot be specified. Examples 1. Deactivate all messages within BTS KILO. ZECC:NAME=KILO;

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

57 (73)

EC - SMS Cell Broadcast Handling

Deactivate all messages within BTSs 17, 18, 19, 20, and 21. ZECC:BTS=17&&21;

Deactivate all messages in all BTSs. ZECC:BTS=0;

Additional information

The message is used for deactivating a BTS or BTSs. This means that all active messages within that particular BTS or BTSs are deactivated. The deactivation will become valid in the next schedule period and this will cause a one-minute delay at the maximum. The execution printout of command example 2 is the following:

Execution printouts

BTS DEACTIVATION: BTS NO. BTS- 17 BTS- 18 BTS- 19 BTS- 20 BTS- 21 BTS NAME ESPOO1 ESPOO2 ESPOO3 ESPOO4 STATE OK BTS ALREADY DEACTIVATED BTS NOT EXISTENT NO SYSTEM BUFFER AVAILABLE ERROR IN DEACTIVATION

COMMAND EXECUTED

The STATE column shows the acknowledgement choices. Semantic error messages Execution error messages If an error occurs, the general semantic error messages of MML commands are used. See Execution printouts.

58 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECD DELETE MESSAGE(S)

Function Parameters Syntax With the ECD command you delete an inactive message or messages. message index;
ECD: ( < message index > ... | < all > ) ;

Parameter explanations

message index
The value range is from 0 to 8068 for BSCi/BSC2i and from 0 to 15000 for BSC3i. The message index value is used for finding a message to be deleted. Value 0 deletes all deactivated messages within the BSC. The parameter is obligatory.

Examples

Delete message with message index 1045. ZECD:1045;

Delete messages with message indexes 401, 454, 455, and 456. ZECD:401&454&&456;

Delete all deactivated messages. ZECD:0;

Additional information Execution printouts

MESSAGE DELETE: MESSAGE INDEX 401

Deletion is not allowed if the message is activated. The execution printout of command example 2 is the following:

STATE OK

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

59 (73)

EC - SMS Cell Broadcast Handling

454 455 456 COMMAND EXECUTED

CB MESSAGE NOT DEACTIVATED COMPLETELY CB MESSAGE NOT EXISTENT ERROR IN DELETING

60 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECP DISPLAY MESSAGE(S)

Function Parameters Syntax With the ECP command you display a message or messages on the output device. BTS identification, BTS name, message index: display format;
ECP: [[ MI = < < [ BTS = < NAME = < message index > ... | all > def ] | BTS identification > | BTS name > ]] :

[ < SHORT > def | [ < LONG > | < HEX > ]] ;

Parameter explanations

message index
MI = decimal The value is used for finding the message to be displayed. The value range is from 0 to 8068 for BSCi/BSC2i and from 0 to 15000 for BSC3i. The default value 0 displays all messages within the BSC. If the parameter NAME or BTS is given, the parameter MI cannot be given.

BTS identification
BTS = decimal The value indicates the BTS whose active short messages are to be displayed. Possible values range from 1 to 2000 (with maximum configuration). If the parameter MI or NAME is given, the parameter BTS cannot be given.

BTS name

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

61 (73)

EC - SMS Cell Broadcast Handling

NAME = text string The name identifies the base transceiver station. The name can contain 1 to 15 characters. If the parameter MI or BTS is given, the parameter NAME cannot be given.

display format
SHORT LONG HEX Displays information on messages in a short format. Displays information on messages in a long format. Displays information on messages in a hexadecimal format.

The default value is SHORT. If the text is written with 8-bit or 16-bit characters, the message text is always displayed as hexadecimal code. Examples 1. Display messages 12 and 18 in a short format. ZECP:MI=12&18; 2. Display all active messages within BTS 49 in a long format. ZECP:BTS=49:LONG; 3. Display all active messages within BTS HELSINKI1 in a long format. ZECP:NAME=HELSINKI1:LONG; 4. Display message 18 in a hexadecimal format. ZECP:MI=18:HEX; 5. Display all messages in a short format. ZECP; Execution printouts The unknown characters are converted into full stops and all characters on the pages are displayed. If the alphabet is not the default 7-bit alphabet, all characters in the message are displayed in hexadecimal format. The abbreviations used in all the short format execution printout headers are the following:

62 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECP DISPLAY MESSAGE(S)

MSG INDEX MSG ID MSG CODE REP RATE M C LANG/ALPH

= = = = = =

message index message identifier message code repetition rate message class language or alphabet identifier

NO OF BC is an abbreviation that is only used in the short format of the execution printout header when all active messages in the BTS are displayed. It indicates the number of completed broadcasts, in other words, the number of times the message has been sent to the air. The execution printout of the commands ZECP;, ZECP:MI=0:SHORT;, and ZECP:MI=0; is the following:
ALL MESSAGES WITHIN THE BSC MSG INDEX 1 2 4 5 6 7 8 11 MSG MSG MESSAGE ID CODE INFORMATON 652 260 This is a test mes 115 574 en................ 403 41 This short message 401 716 03 11 22 33 44 55 900 927 05 11 22 33 44 55 169 1022 zh 0211 2233 4455 45 523 0D 0D 0D 0D 0D 0D 99 146 041A 10A0 10B0 10C0 REP GEOGRAPHICAL RATE SCOPE 4 4 4 963 963 4 4 30 CELL WIDE, IMM PLMN WIDE, NORM CELL WIDE, IMM LA WIDE, NORM CELL WIDE, NORM CELL WIDE, IMM CELL WIDE, IMM CELL WIDE, IMM CODING M GROUP C 0000 0001 0100 0100 1111 0001 1111 0101 3 1 1 LANG/ ALPH DAN 7BIT 7BIT 8BIT 8BIT 16BIT 8BIT 16BIT

COMMAND EXECUTED

If no cell broadcast messages are stored in the BSC memory, the execution printout of the commands ZECP;, ZECP:MI=0:SHORT;, and ZECP:MI=0; is the following:
ALL MESSAGES WITHIN THE BSC MSG INDEX MSG MSG MESSAGE ID CODE INFORMATON REP GEOGRAPHICAL RATE SCOPE CODING M GROUP C LANG/ ALPH

NO CELL BROADCAST MESSAGES EXIST COMMAND EXECUTED

The execution printout of the command ZECP:MI=0:LONG; is the following:

ALL MESSAGES WITHIN THE BSC MESSAGE INDEX MESSAGE IDENTIFIER MESSAGE CODE : : : 1 652 260

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

63 (73)

EC - SMS Cell Broadcast Handling

GEOGRAPHICAL SCOPE CODING GROUP LANGUAGE REPETITION RATE

: CELL WIDE, IMMEDIATE : 0000 : DANISH : 4

en............................................................................. ............................................................................... This short message is a test message with the first page empty except for the language info... MESSAGE INDEX MESSAGE IDENTIFIER MESSAGE CODE GEOGRAPHICAL SCOPE CODING GROUP ALPHABET IDENTIFIER REPETITION RATE : 4 : 403 : 41 : CELL WIDE, IMMEDIATE : 0101 : 7-BIT DEFAULT ALPHABET : 4

This short message is a test message........................................... .............. MESSAGE INDEX MESSAGE IDENTIFIER MESSAGE CODE GEOGRAPHICAL SCOPE CODING GROUP ALPHABET IDENTIFIER REPETITION RATE 03 45 0D 0D 11 54 0D 0D 22 28 0D 0D 33 7D 0D 0D 44 EE 0D 0D 55 43 0D 0D BB 42 0D 0D : 5 : 401 : 716 : LOCATION AREA WIDE, IMMEDIATE : 0100 : 8-BIT DATA/USER-DEFINED CHARACTERS : 4 CC 76 0D 0D DD 55 0D 0D EE C0 0D 0D FF 3B 0D 0D 12 0D 0D 0D 23 0D 0D 0D 34 0D 0D 0D 55 0D 0D 0D 66 0D 0D 0D 77 0D 0D 0D 88 0D 0D 0D 99 0D 0D 0D AA 0D 0D 0D BB 0D 0D 0D CC 0D 0D 0D DD 0D 0D 0D EE 0D 0D 0D FF 0D 0D 0D AE 0D 0D 0D

MESSAGE INDEX MESSAGE IDENTIFIER MESSAGE CODE GEOGRAPHICAL SCOPE CODING GROUP MESSAGE CLASS ALPHABET IDENTIFIER REPETITION RATE

: 6 : 900 : 927 : CELL WIDE, NORMAL : 1111 : 3 : 8-BIT DATA/USER-DEFINED CHARACTERS : 963

05 11 22 33 44 55 BB CC DD EE FF 12 23 34 55 66 77 88 99 AA BB CC DD EE FF 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D

64 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECP DISPLAY MESSAGE(S)

0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D 0D MESSAGE INDEX MESSAGE IDENTIFIER MESSAGE CODE GEOGRAPHICAL SCOPE CODING GROUP ALPHABET IDENTIFIER REPETITION RATE : 7 : 169 : 1022 : CELL WIDE, IMMEDIATE : 0001 : 16-BIT UCS2 CHARACTERS : 4

zh 0211 2233 4455 A0A0 B0B0 C0C0 D0D0 E0E0 F0F0 1020 2030 3040 3030 4040 5050 6060 7070 8080 9090 A0A0 B0B0 C0C0 D0D0 E0E0 F0F0 000D 000D 000D 000D 000D 000D 000D 000D 000D 000D 000D 000D 0D0D 0D0D 0D0D 0D0D 0D0D 0D0D 0D0D MESSAGE INDEX MESSAGE IDENTIFIER MESSAGE CODE GEOGRAPHICAL SCOPE CODING GROUP MESSAGE CLASS ALPHABET IDENTIFIER REPETITION RATE 0D 0D E2 0D 0D 0D E3 0D 0D 0D E4 0D 0D 0D E5 0D 0D 0D E6 0D 0D 0D E7 0D 0D 0D E8 0D : : : : : : : : 8 6045 523 CELL WIDE, IMMEDIATE 1111 CLASS 2, USER-DEFINED 8-BIT DATA/USER-DEFINED CHARACTERS 963 0D 0D E9 0D 0D 0D F1 0D 0D 0D F2 0D 0D 0D F3 0D 0D 0D F4 0D 0D 03 F5 0D 0D C7 F6 0D 0D C8 F7 0D 0D C9 F8 0D 0D D1 F9 0D 0D D2 0A 0D 0D D3 0B 0D 0D D4 0C 0D 0D D5 0D 0D 0D D6 0E 0D 0D D7 0D 0D 0D D8 0D 0D 0D D9 0D 0D 0D E1 0D 0D

MESSAGE INDEX MESSAGE IDENTIFIER MESSAGE CODE GEOGRAPHICAL SCOPE CODING GROUP MESSAGE CLASS ALPHABET IDENTIFIER REPETITION RATE 041A 30C0 50F0 80C0 A0F0 D0C0 00A0 1010 2070 4040 000D 10A0 30D0 60A0 80D0 B0A0 D0E0 00B0 1020 2080 4050 000D 10B0 30E0 60B0 80E0 B0B0 D0F0 00C0 1030 2090 4060 000D 10C0 30F0 60C0 80F0 B0C0 E0A0 00D0 1040 3010 4070 000D

: 11 : 99 : 146 : CELL WIDE, NORMAL : 0101 : 1 : 16-BIT UCS2 CHARACTERS : 30 10D0 40A0 60D0 90A0 B0D0 E0B0 00E0 1050 3020 4080 000D 10E0 40B0 60E0 90B0 B0E0 E0C0 00F0 1060 3030 4090 000D 10F0 40C0 60F0 90C0 B0F0 E0D0 0010 1070 3040 5010 000D 20A0 40D0 70A0 90D0 C0A0 E0E0 0020 1080 3050 5020 000D 20B0 40E0 70B0 90E0 C0B0 E0F0 0030 1090 3060 5030 000D 20C0 40F0 70C0 90F0 C0C0 F0A0 0040 2010 3070 5040 000D 20D0 50A0 70D0 A0A0 C0D0 F0B0 0050 2020 3080 5050 000D 20E0 50B0 70E0 A0B0 C0E0 F0C0 0060 2030 3090 5060 000D 020F 50C0 70F0 A0C0 C0F0 F0D0 0070 2040 4010 5070 000D 30A0 50D0 80A0 A0D0 D0A0 F0E0 0080 2050 4020 5080 000D 30B0 50E0 80B0 A0E0 D0B0 F0F0 0090 2060 4030 5090 000D

COMMAND EXECUTED

The execution printout of the command ZECP:MI=1&11:HEX; is the following:

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

65 (73)

EC - SMS Cell Broadcast Handling

CERTAIN MESSAGE (S) WITHIN THE BSC MESSAGE INDEX MESSAGE IDENTIFIER MESSAGE CODE GEOGRAPHICAL SCOPE CODING GROUP LANGUAGE REPETITION RATE 00000000 00000010 00000020 00000030 00000040 00000050 54 67 73 0D 0D 0D 68 65 61 0D 0D 0D 69 20 67 0D 0D 0D : 1 : 652 : 260 : CELL WIDE, IMMEDIATE : 0000 : DANISH : 4 73 69 65 0D 0D 0D 20 73 2E 0D 0D 0D 73 20 OD 0D 0D 0D 68 61 0D 0D 0D 0D 6F 20 0D 0D 0D 0D 72 74 0D 0D 0D 0D 74 65 0D 0D 0D 0D 20 73 0D 0D 0D 0D 6D 74 0D 0D 0D 0D 65 20 0D 0D 0D 0D 73 6D 0D 0D 0D 73 65 0D 0D 0D 61 73 0D 0D 0D This short messa ge is a test mes sage............ ................ ................ .............

MESSAGE INDEX MESSAGE IDENTIFIER MESSAGE CODE GEOGRAPHICAL SCOPE CODING GROUP MESSAGE CLASS ALPHABET IDENTIFIER REPETITION RATE 00000000 00000010 00000020 00000030 00000040 00000050 00000052 00000062 00000072 00000082 00000092 000000A2 000000A4 000000B4 000000C4 000000D4 000000E4 000000F4 000000F6 00000106 00000116 00000126 00000136 00000146 04 20 30 40 60 70 70 90 A0 B0 D0 E0 E0 00 00 10 20 20 30 30 40 50 00 00 1A B0 D0 F0 B0 D0 E0 A0 C0 E0 A0 D0 E0 A0 30 20 10 90 10 90 80 70 0D 0D 10 20 30 50 60 70 90 A0 B0 D0 E0 00 00 10 20 30 40 40 50 00

: 11 : 99 : 146 : CELL WIDE, NORMAL : 0101 : 1 : 16-BIT UCS2 CHARACTERS : 30 A0 C0 E0 A0 C0 F0 B0 D0 F0 B0 F0 B0 40 30 20 20 10 90 80 0D 10 20 30 50 60 80 90 A0 C0 D0 F0 00 00 10 20 30 40 50 50 00 B0 D0 F0 B0 D0 A0 C0 E0 A0 C0 A0 C0 50 40 30 30 20 10 90 0D 10 20 40 50 60 80 90 A0 C0 D0 F0 00 00 10 20 30 40 50 00 00 C0 E0 A0 C0 E0 B0 D0 F0 B0 E0 B0 D0 60 50 40 40 30 20 0D 0D 10 02 40 50 60 80 90 B0 C0 D0 F0 00 00 10 20 30 40 50 00 00 D0 0F B0 D0 F0 C0 E0 A0 C0 F0 C0 E0 70 60 50 50 40 30 0D 0D 10 30 40 50 70 80 90 B0 C0 E0 F0 00 00 10 20 30 40 50 00 00 E0 A0 C0 E0 A0 D0 F0 B0 D0 A0 D0 F0 80 70 60 60 50 40 0D 0D 10 30 40 50 70 80 A0 B0 C0 E0 F0 00 00 10 20 30 40 50 00 00 F0 B0 D0 F0 B0 E0 A0 C0 E0 B0 E0 10 90 80 70 70 60 50 0D 0D 20 30 40 60 70 80 A0 B0 C0 E0 F0 00 10 10 20 30 40 50 00 00 A0 C0 E0 A0 C0 F0 B0 D0 F0 C0 F0 20 10 90 80 80 70 60 0D 0D .............. . . . . ...0.0.0. 0.0.0.@.@.@.@.@. @.P.P.P.P.P.P.`. `.`.`.`.`.p.p.p. p. p.p............. ................ ................ ................ ................ .. ................ ............... [email protected].`.p...... . [email protected].`.p.... . 0 @ P ` p . . 0.0 000@0P0`0p0. 0.@.@ @0@@@P@`@p @[email protected] P0P@PPP` PpP.P........... ................

COMMAND EXECUTED

The execution printout of the commands ZECP:MI=4:SHORT;, and ZECP:MI=4; is the following:

66 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECP DISPLAY MESSAGE(S)

CERTAIN MESSAGE (S) WITHIN THE BSC MSG INDEX 4 MSG MSG MESSAGE ID CODE INFORMATION 403 41 This short message REP GEOGRAPHICAL RATE SCOPE 4 CELL WIDE, IMM CODING M GROUP C 0100 LANG/ ALPH 7BIT

COMMAND EXECUTED

The execution printout of the command ZECP:MI=4:LONG; is the following:

CERTAIN MESSAGE (S) WITHIN THE BSC MESSAGE INDEX MESSAGE IDENTIFIER MESSAGE CODE GEOGRAPHICAL SCOPE CODING GROUP ALPHABET IDENTIFIER REPETITION RATE : 4 : 403 : 41 : CELL WIDE, IMMEDIATE : 0101 : 7-BIT DEFAULT ALPHABET : 4

This short message is a test message........................................... .............. COMMAND EXECUTED

The execution printout of the commands ZECP:BTS=2; and ZECP: BTS=2:SHORT; is the following:
ALL ACTIVE MESSAGES WITHIN THE BTS-002 ESPOO2 MSG INDEX 6 7 11 MSG MSG MESSAGE ID CODE INFORMATON 900 927 05 11 22 33 44 55 169 1022 zh 0211 2233 4455 99 146 041A 10A0 10B0 10C0 REP GEOGRAPHICAL RATE SCOPE CODING M GROUP C 3 1 LANG/ NO OF ALPH BC 8BIT 26 16BIT 20014 16BIT 115

963 CELL WIDE, NORM 1111 4 CELL WIDE, IMM 0001 30 CELL WIDE, IMM 0101

COMMAND EXECUTED

The execution printout of the command ZECP:NAME=ESPOO2:LONG; is the following:

ALL ACTIVE MESSAGES WITHIN THE BTS-002 ESPOO2 MESSAGE INDEX MESSAGE IDENTIFIER MESSAGE CODE GEOGRAPHICAL SCOPE CODING GROUP MESSAGE CLASS ALPHABET IDENTIFIER REPETITION RATE : 6 : 900 : 927 : CELL WIDE, NORMAL : 1111 : 3 : 8-BIT DATA/USER-DEFINED CHARACTERS : 963

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

67 (73)

EC - SMS Cell Broadcast Handling

MESSAGE BROADCAST 26 TIMES 05 0D 0D 0D 11 0D 0D 0D 22 0D 0D 0D 33 0D 0D 0D 44 0D 0D 0D 55 0D 0D 0D BB 0D 0D 0D CC 0D 0D 0D DD 0D 0D 0D EE 0D 0D 0D FF 0D 0D 0D 12 0D 0D 0D 23 0D 0D 0D 34 0D 0D 0D 55 0D 0D 0D 66 0D 0D 0D 77 0D 0D 0D 88 0D 0D 0D 99 0D 0D 0D AA 0D 0D 0D BB 0D 0D 0D CC 0D 0D 0D DD 0D 0D 0D EE 0D 0D 0D FF 0D 0D 0D 0D 0D 0D 0D

MESSAGE INDEX MESSAGE IDENTIFIER MESSAGE CODE GEOGRAPHICAL SCOPE CODING GROUP ALPHABET IDENTIFIER REPETITION RATE

: 7 : 169 : 1022 : CELL WIDE, IMMEDIATE : 0001 : 16-BIT UCS2 CHARACTERS : 4

MESSAGE BROADCAST 20014 TIMES zh 0211 2233 4455 A0A0 B0B0 C0C0 D0D0 E0E0 F0F0 1020 2030 3040 3030 4040 5050 6060 7070 8080 9090 A0A0 B0B0 C0C0 D0D0 E0E0 F0F0 000D 000D 000D 000D 000D 000D 000D 000D 000D 000D 000D 000D 0D0D 0D0D 0D0D 0D0D 0D0D 0D0D 0D0D MESSAGE INDEX MESSAGE IDENTIFIER MESSAGE CODE GEOGRAPHICAL SCOPE CODING GROUP MESSAGE CLASS ALPHABET IDENTIFIER REPETITION RATE : 11 : 99 : 146 : CELL WIDE, NORMAL : 0101 : 1 : 16-BIT UCS2 CHARACTERS : 30

MESSAGE BROADCAST 115 TIMES 041A 30C0 50F0 80C0 A0F0 D0C0 00A0 1010 2070 4040 000D 10A0 30D0 60A0 80D0 B0A0 D0E0 00B0 1020 2080 4050 000D 10B0 30E0 60B0 80E0 B0B0 D0F0 00C0 1030 2090 4060 000D 10C0 30F0 60C0 80F0 B0C0 E0A0 00D0 1040 3010 4070 000D 10D0 40A0 60D0 90A0 B0D0 E0B0 00E0 1050 3020 4080 000D 10E0 40B0 60E0 90B0 B0E0 E0C0 00F0 1060 3030 4090 000D 10F0 40C0 60F0 90C0 B0F0 E0D0 0010 1070 3040 5010 000D 20A0 40D0 70A0 90D0 C0A0 E0E0 0020 1080 3050 5020 000D 20B0 40E0 70B0 90E0 C0B0 E0F0 0030 1090 3060 5030 000D 20C0 40F0 70C0 90F0 C0C0 F0A0 0040 2010 3070 5040 000D 20D0 50A0 70D0 A0A0 C0D0 F0B0 0050 2020 3080 5050 000D 20E0 50B0 70E0 A0B0 C0E0 F0C0 0060 2030 3090 5060 000D 020F 50C0 70F0 A0C0 C0F0 F0D0 0070 2040 4010 5070 000D 30A0 50D0 80A0 A0D0 D0A0 F0E0 0080 2050 4020 5080 000D 30B0 50E0 80B0 A0E0 D0B0 F0F0 0090 2060 4030 5090 000D

COMMAND EXECUTED

If there are no active cell broadcast messages in a certain BTS:

ALL ACTIVE MESSAGES WITHIN THE BTS-002 ESPOO2 NO ACTIVE MESSAGES WITHIN THE BTS COMMAND EXECUTED

68 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECP DISPLAY MESSAGE(S)

Semantic error messages Execution error messages

If an error occurs, the general semantic error messages of MML commands are output.

/*** CB MESSAGE NO.4

NOT EXISTENT ***/

The cell broadcast message does not exist.

/*** EXECUTION FAILED ***/ /*** TRY AGAIN ***/

The program cannot display the short message.

/*** BTS NOT EXISTENT ***/

The cell does not exist.

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

69 (73)

EC - SMS Cell Broadcast Handling

70 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECL DISPLAY BTS WORK LOAD

Function Parameters Syntax With the ECL command you display the workload of a BTS or BTSs. BTS identification, BTS name;
ECL: [ BTS = < BTS identification > ... | < all > def | NAME= < BTS name > ... ] ;

Parameter explanations

BTS identification
BTS = decimal The value indicates the BTSs whose workload is to be displayed. Possible values range from 1 to 2000 (with maximum configuration). The default value 0 displays workloads of all BTSs. The characters & and && can be used. If the parameter NAME is given, the parameter BTS cannot be given.

BTS name
NAME = text string The name identifies the base transceiver station. The name can contain 1 to 15 characters. Several names can be given at the same time by using the character &. If the parameter BTS is given, the parameter NAME cannot be given. Examples 1. Display the workload of BTS HELSINKI1. ZECL:NAME=HELSINKI1;

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

71 (73)

EC - SMS Cell Broadcast Handling

Display the workload of BTSs 91, 2, and 5. ZECL:BTS=91&2&5;

Display the workload of all BTSs. ZECL;

Execution printouts

The execution printout of command example 2 is the following:

WORK LOAD OF BTS (S) BTS NO. BTS 1 BTS2 BTS 5 BTS NAME ROVANIEMI OULU1 WORK LOAD (%) 50 100 BTS NOT EXISTENT

COMMAND EXECUTED

If no BTSs have been created, the execution printout of command example 3 is the following:
*** ALL BTS NOT EXISTENT *** COMMAND EXECUTED

If not all the possible BTSs have been created, the execution printout of command example 3 is the following:
WORK LOAD OF BTS (S) BTS NO. BTS 1 BTS 2 BTS 3 BTS- 10 BTS- 11 BTS- 12 BTS- 13 BTS- 14 BTS- 15 BTS- 16 BTS- 17 BTS- 40 BTS- 41 BTS- 43 BTS- 44 BTS- 45 BTS- 46 BTS- 47 BTS- 48 BTS- 49 BTS- 50 BTS- 91 BTS NAME MAKKYLA1 OULU LEPPAVAARA2 PITAJANMAKI HELSINKI2 HELSINKI3 HELSINKI5 HELSINKI6 HELSINKI7 HELSINKI8 HELSINKI9 MAKKYLA LEPPAVAARA PITAJANMAKI HELSINKI1 HELSINKI4 MAKKYLA2 MAKKYLA3 MAKKYLA4 MAKKYLA5 HELSINKI6 ROVANIEMI WORK LOAD (%) 25 100 90 74 12 00 00 10 07 30 38 100 98 00 65 60 50 55 10 23 40 50

72 (73)

# Nokia Siemens Networks

DN9813172 Issue 14-0 en 29/02/2008

ECL DISPLAY BTS WORK LOAD

* REST OF THE BTS NOT EXISTENT * COMMAND EXECUTED

Semantic error messages Execution error messages

If an error occurs, the general semantic error messages of MML commands are used.

/* EXECUTION FAILED / / TRY AGAIN */

The program cannot display the workload of a BTS or BTSs. If other errors occur, the general execution error messages of MML commands are used.

DN9813172 Issue 14-0 en 29/02/2008

# Nokia Siemens Networks

73 (73)

Data Acquisition from HD Vehicles Using J1939 CAN Bus
From Everand
Data Acquisition from HD Vehicles Using J1939 CAN Bus
Richard Walter
No ratings yet
Mobile Network Optimization: A Guide for 2G and 3G Mobile Network Optimization
From Everand
Mobile Network Optimization: A Guide for 2G and 3G Mobile Network Optimization
Emmanuel Usuah
3.5/5 (3)
SMS Flow
100% (2)
SMS Flow
89 pages
Indoor Radio Planning: A Practical Guide for 2G, 3G and 4G
From Everand
Indoor Radio Planning: A Practical Guide for 2G, 3G and 4G
Morten Tolstrup
5/5 (1)
Z-Wave Essentials
From Everand
Z-Wave Essentials
Christian Paetz
5/5 (1)
Fsec Ovp PDF
No ratings yet
Fsec Ovp PDF
8 pages
TS 3GBTS HW 0154 - I1
No ratings yet
TS 3GBTS HW 0154 - I1
6 pages
Nokia Wcdma Base Station Product Overview: Document Number/Version B6I 067208AE/3.0.0
No ratings yet
Nokia Wcdma Base Station Product Overview: Document Number/Version B6I 067208AE/3.0.0
38 pages
Flexi EDGE BTS Feature Description
No ratings yet
Flexi EDGE BTS Feature Description
81 pages
Module 01 - Introduction To EDGE PDF
100% (1)
Module 01 - Introduction To EDGE PDF
17 pages
11b BICC
No ratings yet
11b BICC
63 pages
NSN Appendix Abbreviations
No ratings yet
NSN Appendix Abbreviations
12 pages
Base Station Subsystem Essentials (S13) : CT2102EN13GLA00
No ratings yet
Base Station Subsystem Essentials (S13) : CT2102EN13GLA00
0 pages
(E) GPRS BSS Optimization - S12
No ratings yet
(E) GPRS BSS Optimization - S12
208 pages
Nokia 12 GSM Module: at Command Guide
No ratings yet
Nokia 12 GSM Module: at Command Guide
24 pages
FTM Parameters RU30
No ratings yet
FTM Parameters RU30
508 pages
TS BSC HW 0180 I2
No ratings yet
TS BSC HW 0180 I2
5 pages
Cellular Radio Network Management
No ratings yet
Cellular Radio Network Management
91 pages
BSC Timer Value and
No ratings yet
BSC Timer Value and
18 pages
Flexi WCDMA BTS Installation and Commissioning - WN6.0 - RU20
No ratings yet
Flexi WCDMA BTS Installation and Commissioning - WN6.0 - RU20
8 pages
TCSM3i Functionalities: BSC3119 Nokia BSC/TCSM, Rel. S12, Product Documentation, v.5
No ratings yet
TCSM3i Functionalities: BSC3119 Nokia BSC/TCSM, Rel. S12, Product Documentation, v.5
35 pages
Bts
No ratings yet
Bts
221 pages
Bsspar 150623050238 Lva1 App6892 PDF
No ratings yet
Bsspar 150623050238 Lva1 App6892 PDF
221 pages
GSM/EDGE BSS, Operating Documentation: BSC Transport Site Solution
No ratings yet
GSM/EDGE BSS, Operating Documentation: BSC Transport Site Solution
86 pages
Changes in WBTS3.3 Commissioning Parameters_v1
No ratings yet
Changes in WBTS3.3 Commissioning Parameters_v1
60 pages
BICC Slide
No ratings yet
BICC Slide
32 pages
05 RN2010EN13 BSSPAR1 S13 Chapter 05 Measurement Processing v1.1
No ratings yet
05 RN2010EN13 BSSPAR1 S13 Chapter 05 Measurement Processing v1.1
27 pages
Sigman TATA
No ratings yet
Sigman TATA
22 pages
Base Station Subsystem Essentials RG20 (BSS) : RN2812EN20GLA00
No ratings yet
Base Station Subsystem Essentials RG20 (BSS) : RN2812EN20GLA00
7 pages
02 - RN20022EN14GLN1 - EGPRS Network Audit PDF
No ratings yet
02 - RN20022EN14GLN1 - EGPRS Network Audit PDF
60 pages
Summary of Corrections and Enhancements
No ratings yet
Summary of Corrections and Enhancements
7 pages
2G SGSN RNW Parameters
No ratings yet
2G SGSN RNW Parameters
174 pages
Wip Ra57210-V-5g19b_le03_bearer Control
No ratings yet
Wip Ra57210-V-5g19b_le03_bearer Control
37 pages
GSM/EDGE BSS, Operating Documentation: BSC Transport Site Solution
No ratings yet
GSM/EDGE BSS, Operating Documentation: BSC Transport Site Solution
101 pages
Reference System Description: Packet Core System Paco 2.1, System Documentation
No ratings yet
Reference System Description: Packet Core System Paco 2.1, System Documentation
13 pages
SURPASS HiT7035 R4 2 Acceptance Test Manual
No ratings yet
SURPASS HiT7035 R4 2 Acceptance Test Manual
72 pages
SURPASS HiT7035 R4.2 Acceptance Test Manual
100% (1)
SURPASS HiT7035 R4.2 Acceptance Test Manual
72 pages
00 Ra2275en02gla00 RTC
No ratings yet
00 Ra2275en02gla00 RTC
6 pages
Flexi WCDMA BTS - Introduction
100% (1)
Flexi WCDMA BTS - Introduction
28 pages
De 34
No ratings yet
De 34
383 pages
MetroSoDe1 V 2 0
No ratings yet
MetroSoDe1 V 2 0
37 pages
Multipair Ethernet over DMT ver.2: ver, #2
From Everand
Multipair Ethernet over DMT ver.2: ver, #2
Ashlan Chidester
No ratings yet
dn0967192 0900d805808e9404
No ratings yet
dn0967192 0900d805808e9404
799 pages
Netmonitor Manual
No ratings yet
Netmonitor Manual
34 pages
GSM Architecture
No ratings yet
GSM Architecture
50 pages
Features For Optimization: RN2022-13N RANOP - Radio Network Optimization Principles
No ratings yet
Features For Optimization: RN2022-13N RANOP - Radio Network Optimization Principles
21 pages
3G NSN Terms Vocabulary
No ratings yet
3G NSN Terms Vocabulary
18 pages
00 - CN3138-01A Service Description
No ratings yet
00 - CN3138-01A Service Description
8 pages
Call Setup Example 1
No ratings yet
Call Setup Example 1
12 pages
NSN RG10 (BR) Systeme Overview
No ratings yet
NSN RG10 (BR) Systeme Overview
8 pages
Field Test Nokia
No ratings yet
Field Test Nokia
8 pages
Nokia EDGE - Evolution
No ratings yet
Nokia EDGE - Evolution
16 pages
RG10(BR) MP 3.0_BB_Change_Notes
No ratings yet
RG10(BR) MP 3.0_BB_Change_Notes
152 pages
3G Core Network MGW For MSS (U3B) Training Document
No ratings yet
3G Core Network MGW For MSS (U3B) Training Document
60 pages
Correct Maintenance - Cognex DataMan 8500
From Everand
Correct Maintenance - Cognex DataMan 8500
Unique Content
No ratings yet
Telecom Protocols: In-Depth Analysis: Telecom Titans: Building the Connected World, #7
From Everand
Telecom Protocols: In-Depth Analysis: Telecom Titans: Building the Connected World, #7
Jordan Grant
No ratings yet
Communication & Energy Wire & Cables World Summary: Market Values & Financials by Country
From Everand
Communication & Energy Wire & Cables World Summary: Market Values & Financials by Country
Editorial DataGroup
No ratings yet
Introduction to GSM: Second Edition
From Everand
Introduction to GSM: Second Edition
Guy Inchbald
No ratings yet
Advanced Modulation Techniques: Telecom Titans: Building the Connected World, #2
From Everand
Advanced Modulation Techniques: Telecom Titans: Building the Connected World, #2
Jordan Grant
No ratings yet
Automotive Computer Network Repair
From Everand
Automotive Computer Network Repair
Mandy Concepcion
4.5/5 (7)