CCENT Notes Part 4 Wide-Area Networks

Ref : CCENT/CCNA ICND1 Official Exam Certification Guide, Second Edition by Wendell Odom

It is highly recommended that you read at least once the above study guide to make full use of this notes, it is expected that there may be minor errors in this notes, please always refer the study guide for accurate information.

(Jojo Jacob - CCENT)

TABLE OF CONTENTS
Chapter 16 WAN Concepts..............................................................................................3 Chapter 17 WAN Configuration.....................................................................................15

Chapter 16 WAN Concepts

WAN Technologies Voice calls with PCM (Pulse Code Modulation) codec in use consumes 64 Kbps through the digital part of the PSTN (when using links like T1 and T3s inside the Telco) Analog Modems A Telephone converts sound waves into analog electrical signals, a modem converts a stream of binary digits on a computer to into representative analog electrical signal. The modems modulates and de-modulates the analog signals at the sending and receiving ends. Modems create an asynchronous circuit, but a leased line creates a synchronous circuit with CSU/DSUs synchronizing the speeds. Analog Modems basically uses the dial-up technology and max. speed is around 100 kbps.. Digital Subscriber Line (DSL) Comparison between DSL and Modem Some of the key features of DSL service DSL allows analog voice signals, and digital data signals to be sent over the same local loop wiring at the same time The local loop must be connected some thing besides the traditional voice switch at the local CO, in this case a device called DSL Access Multiplexer (DSLAM). DSL allows for a concurrent voice call to be up at the same time as the data connection Unlike modems, the DSL data component is always on, in other words you dont have to signal or dial a phone number to set up a data circuit.

DSL Connection from Home to an ISPTypical topology and devices used for DSL

TELCO - CO

IP Network Owned by ISP

HOME

` Ethernet Digital Signal > 4000 Hz IP Traffic Split to ISP Router Local Loop DSLAM

DSL Router / Modem

DTMF Tones, Analog Voice, 0 4000 Hz

Analog Voice Split to Voice Switch PSTN

Voice Switch w/PCM

Telephone wall jack in uses RJ-11 connectors. RJ11 is a physical interface often used for terminating telephone wires. It is probably the most familiar of the registered jacks, being used for single line POTS telephone jacks in most homes across the world. RJ14 is similar, but for two lines, and RJ25 is for three lines. RJ61 is a similar registered jack for four lines. The telephone line cord and its plug are more often a true RJ11 with only two conductors. Phone generates analog signals at the rate of 0 4000 Hz, and the DSL modem uses frequencies higher than 4000 Hz, so that the phone and the DSL signals interfere very much, still need to use a filter. The DSLAM directs (multiplexes) the analog voice signals frequency range between 0 Hz and 4000 Hz, to a voice switch.

Two views of an RJ25 6P6C crimp-on style connector. . RJ11 is a physical interface often used for terminating telephone wires. It is probably the most familiar of the registered jacks, being used for single line POTS telephone jacks in

BS6312 431A plug; colloquially, a British Telecom plug. Used in NZ.

DSL Types Symetric DSL means that link speed in both directions is the same, and Asymetric means more download speed as compared to a relatively low upload speed. Acronym ADSL CDSL (G.lite) VDSL SDSL HDSL IDSL Spelled Out Asymetric DSL Consumer DSL Very-high-data-rate DSL Symmetric DSL High-data-rate DSL ISDN DSL Type Asymmetric Asymmetric Asymmetric Symmetric Symmetric Symmetric

Factors that affect speed of DSL line. The speed of a DSL line can vary based on many factors, including The distance between the CO and the consumer (the longer the distance, the slower the speed) The quality of the local loop cabling (the worse the wiring, the slower the speed) The type of DSL (each standard has different maximum theoretical speed) The DSLAM used in the CO, (older equipment may not have, recent improvements that allow for faster speeds, on lower grade local loops)

Theoretical maximum speed of an ADSL line on local loop is 10 Mbps (8.192 Mbps). Most ISPs quote it as 1.5 Mbps downstream, 384 kbps upstream. ADSL support local loops upto 18,000 feets, 5 Kms.

CABLE Internet
CABLE Company Facitlity

HOME

SATELITE

` Ethernet Cable Modem F-connectors HEAD END Spiter TV

ISP Router

The equipment at the Head End splits the channels used for internet over to an ISP Router. Comparison of Analog, DSL and Cable ModemComparison points for Internet Access Technologies Analog Modem DSL Cable Modem Transport Telco Local loop Telco Local loop CATV Cable Supports symmetric Speeds Yes Yes No Supports asymmetric speed Yes Yes Yes Typical practical speed Upto 100kbps 1.5 Mbps 3 6 Mpbs downstream downstream Allows concurrent voice and No Yes Yes data Always-on Internet Service No Yes Yes Local loop distance issue No Yes No Throughput degrades under No No Yes higher loads

ATM Packet Switching Service ATM supports much higher physical link speed compared to Frame relay, especially when using specification called Synchronous Optical Network (SONET). ATM does not forward frames as in Frame relay, but it forwards Cells. ATM cells are always fixed 53 bytes in length. 48 bytes of payload (data) and 5 byte header. ATM header contains two fields that act like Data link connection identifier (DLCI) in frame relay, by identifying each VC (Virtual Channel) , these two fields are called, Virtual Path Identifier (VPI) and Virtual Channel Identifier (VCI). When a router need to convert an Ethernet frame into an ATM cell, it creates the ATM cells by splitting the data link frame into 48 bytes segments, each segment is placed in a cell with 5 byte header. The other end router does the reassembly of ATM cells to Ethernet frames. The whole process of segmenting frame into cells and reassembling them is called segmentation and reassembly (SAR). Circuit Switching : is the physical ability to send or receive data and voice across two end points. Packet Switching : The device interpret the bits, and decides forwarding decisions based on some type of address fields in the header. Comparison of circuit switching and packet switching. Features Circuit switching Service implemented as OSI Layer 1 Point-to-Point (two devices) or more Point-to-Point Packet switching 2 Multi point (more than two)

IP Services for Internet Access

Besides basic routing, the access router needs to perform three additional important functions, assigning addresses, learning routes, and translate address. (NAT).

Internet access equipments separate devices.

` PC1 Fast Ethernet Interfaces Fa0/0 Fa0/1 R1 Cable Modem IP Addresses are in same subnet ` PC2 DSL Router / Modem

CATV Cable

ISP/Internet

ISP1

Address assignment on Internet Access Routers. Factors that impact the IP Addresses used by internet access routers. The internet access router (R1) has two interfaces, one facing the internet, and other facing the devices at that site, the router needs IP addresses on each of these interface, the IP addresses are chooses as per the following rules The internet facing interfaces need one public IP address so that the routers in the internet knows how to route packet to the access router The ISP typically assigns that public (globally routable) ip address dynamically using DHCP. The local PCs typically needs to dynamically learn IP addresses using DHCP, so the access router acts as a DHCP server for the local hosts. The router needs a statically configured ip address on the local subnet, using a private network number

The local LAN subnet will use ip address in private network number.

DHCP Client and Server Function in an Access Router

R1 as DHCP Server R1 as DHCP Client

` PC1

192.168.1.101/24 GW 192.168.1.1 DNS 198.133.219.2 DHCP Server 64.100.1.1/30 GW 64.100.1.2 DNS 198.133.219.2 ISP/Internet R1 64.100.1.2 ISP1

192.168.1.1

` PC2

192.168.1.102/24 GW 192.168.1.1 DNS 198.133.219.2

ISPs DNS Server 198.133.219.2

Access router is part of the Integrated DLS/Cable Modem. And is a customer located equipment. Access router R1 needs a statically configured IP address on its local LAN facing interface, a DHCP server function enabled on that interface, and DHCP client function enabled on its internet facing interface. Routing for the Interface Access Router The access router creates a default route with its default gateway(ISP router interface) as its next-hop router. The default gateway settings on the locals PCs, along with the default route on the access router allows PCs to send packets that reach internet. However the traffic from internet to local PCs are incomplete, as the internet routes will never have a route for the private ip address for hosts PC1 and PC2, this problem is solved by NAT and PAT.

10

NAT and PAT NAT : Network Address Translation PAT : Port Address Translation ISP try to conserve public IP address by assigning only minimum (one) public IP address to each access router, not to each local hosts connected to it. A key concept of PAT : there is no important difference between some number of TCP connections from different hosts, versus the same number of TCP connections from the same hosts. Three connections from three PCs

64.100.1.1 Port 1024 64.100.1.1 PC 64.100.1.2 PC 64.100.1.3 Port 1033 64.100.1.3 PC 64.100.1.2 Port 1024 Internet 128.107.1.1 Port 80 Server 128.107.1.1 128.107.1.1 Port 80 128.107.1.1 Port 80

Three connections from ONE PC

64.100.1.1 Port 1024 128.107.1.1 Port 80 64.100.1.1 Port 1025 Internet PC 64.100.1.1 Port 1026 128.107.1.1 Port 80 Server 128.107.1.1

64.100.1.1

128.107.1.1 Port 80

The top part of the figure shows a network with three different hosts connecting to a web server using TCP. The bottom part shows three TCP connection from a single host. All six connection connect to Server 128.107.1.1 port 80. In each of these cases the server is

11

able to differentiate between each connection, because each has a unique combination of IP address and port number. PAT allows the local hosts to use private ip addresses, while the access router uses a single public ip address. PAT takes advantage of the fact that a sever does not care if it has one connection each to three different hosts, or three connections to a single host ip address. PAT translates the local hosts private IP address to the access routers public ip address, also to tell which ip packet needs to be sent back which local hosts, router keeps track of both ip address and TCP/UDP port number. Shows how PAT translates IP Addresses in an Internet Access Router.

1 SA 192.168.1.101 S.Port : 1024 2 SA 64.100.1.1 S.Port : 1024 PC1 64.100.1.1 R1 4 DA 192.168.1.101 D.Port : 1024 Server 128.107.1.1

3 DA 64.100.1.1 D.Port : 1024

NAT Translation Table Inside Local Inside Global 192.168.1.101:1024 64 .100.1.1 : 1024 192.168.1.102:1024 64 .100.1.1 : 1025

The numbered steps in the figure follow the logic. 1. PC1 sends a packet to server 128.107.1.1 and as per PC1s default gateway setting send the packet to access router R1. 2. R1 performs PAT, based on the on the routers NAT translation table, changing the local hosts private ip address to routers public ip address, R1 then forwards the packet based on its default route 3. When the server replies to the packet sent from PC1, server sends the packet to router R1s address, with a destination port 1024. Internet routers know how to forward the packet to R1, because it uses a public ip address.

12

4. R1 changes the destination ip address and port based on the NAT table, switching destination ip address/port from 64.100.1.1 : 1024 to 192.168.1.101 : 1024 and R1 knows the route to reach 192.168.1.101 because this address is in subnet connected to R1. NAT uses the following key terms Inside Host : Refers to a host inside the enterprises network Inside Local : Refers to an IP address in an IP header, with that address representing a local host as the packet passes over the local enterprise network. In this case 192.168.1.101 and 102 are inside local IP addresses, and packets at step 1, and 4 in the above figure shows inside local ip addresses. Inside Global : Refers to an IP address in an IP header, with that address representing a local host, as the packet passes over the global internet. In this case, 64.100.1.1 is the one inside global IP address, and the packets in step 2 and 3 in the above figure show inside global ip addresses. Inside Interface : The router interface connected to the same LAN as the inside hosts Outside Interface: The router interface connected to the internet Definitions. ADSL : Asymmetric Digital Subscriber Line, one of many DSL technologies, ADSL is designed to deliver more bandwidth downstream, than upstream. Asymmetric : A feature of many internet access technologies including DSL, cable and modems, in which downstream transmission rate is higher than the upstream transmission rate. ATM : Asynchronous Transfer Mode, The international standard for cell relay, in which multiple service types, such as voice, video and data, are conveyed in fixed length, 53 byte cells. Fixed length cells allow cell processing to occur in hardware, thereby reducing transit delays. DSL : Digital Subscriber Line, Public network technology that delivers high bandwidth over conventional telco local loop copper wiring at limited distance. Typically used as an internet access technology, connecting use to an ISP. Inside Global : For packets send to and from host that resides in the trusted part of a network that uses NAT, a term referring to the IP address used in the headers of that packets, when those packets traverse the global (public) internet.

13

Inside Local : For packets sent to and from hosts that reside in the trusted part of a network that uses NAT, a term referring to the IP addresses used in the headers of those packets when they traverse enterprises (private) part of the network. Modem : Modulator demodulator. A device that converts between digital and analog signals so that a computer can send data to another computer using analog telephone lines. NAT : Network Address Translation. A mechanism for reducing the need for globally unique (public) IP addresses. NAT allows an organization with addresses that are not globally unique to connect to the internet by translating those addresses into public addresses, in the globally routable address space. PAT : Port Address Translation. A NAT feature in which one Inside Global IP address supports over 65,000 concurrent TCP and UDP connections. PSTN : Public Switched Telephone Network, A general term referring to variety of telephone networks and services in place worldwide. Some times called POTS, or Plain Old Telephone Service. Symmetric : A feature of many internet access technologies in which downstream transmission rate is same as the upstream transmission rate.

14

Chapter 17 WAN Configuration

Configuring Point-to-Point WAN Configuring HDLC No layer 1 or Layer 2 commands are required for a routers Ethernet or serial interface, by default assumes Ethernet and HDCL as the data link layer protocols respectively. Only command that is required is to configure ip address on the interface, and a no shutdown command if the interface is administratively down. Optional and required configuration steps for a serial link between two routers.Configuration steps on a serial link.. Step 1. Configure Interface IP address using ip address interface subcommand Step 2. The following tasks are required only when the specifically listed conditions are true. a. if an encapsulation protocol interface subcommand lists a protocol besides HDLC already exists on the interface, use encapsulation HDLC interface subcommand to enable HDLC b. if the interface status is administratively down, enable the interface using the no shutdown interface sub command c. if the serial link is a back to back serial link in a lab, configure the clocking rate using the clock rate speed interface sub command, but only on the one router with the DCE cable attached, (show controllers serial number, command) Step 3. The following steps are optional, and have no impact on whether the link works and passes IP traffic. a. configure the link speed using the bandwidth speed-in-kbps interface subcommand b. configure the description text subcommand on the interface for documentation purposes Configure PPP To migrate from a working HDLC link (default) to a working PPP link, the only command needed is an encapsulation ppp command on each of the two routers serial interfaces. 15

Configuring and Troubleshooting Internet Access Routers Internet Access Routers : Configuration Steps Step 1. Establish IP connectivity, plan and configure from CLI, IP address on the local LAN, so that PC on the LAN can ping the routers LAN interface. Step 2 : Install and access SDM (Cisco Router and Security Device Manager) , install SDM on the router, and access the routers SDM interface using the PC that can ping routers ip address Step 3. Configure DHCP and PAT. Use SDM to configure both DHCP client services and PAT services on the router Step 4. Plan for DHCP services, plan the IP address to be assigned by the router to the hosts on the local LAN, along with the DNS ip address, Domain name, and default gateway settings that the router will advertise Step 5. Configure DHCP Server, Use SDM to configure DHCP server features on the router Step 1. Establish IP Connectivity IP Address details planned and configured on the local LAN for an internet access router. a. Choose any private IP network number (generally a class c 192.168.1.1 network) b. choose a mask that allows for enough hosts (typically the default mask is fine) c. choose the router ip address from the network number

` PC1 Fast Ethernet Interfaces Fa0/0 Fa0/1 R1 Cable Modem IP Addresses are in same subnet ` PC2 DSL Router / Modem ISP1

CATV Cable

ISP/Internet

16

Step 2. Install and Access SDM Installation and accessing SDM from a host requires ip connectivity between host and the router, and additional steps and configuration as per the SDM installation manuals. Step 3 Configuring DHCP and PAT Pleas refer to page 549 through to 554 for SDM configuration wizards . which asks for the user inputs and configures the router DHCP client and PAT features. Step 4. Plan for DHCP services The following lists outlines the key items that you need to gather before you configure the router as a DHCP server, the first two items related to planning on the local LAN, and the last two items are values learned from the ISP, that just needs to be passed on to the hosts in the local LAN. 1. Recall the private network number and the mask used on the local LAN, and choose a subset of that network, that can be assigned to hosts using DHCP 2. Make a note of the routers ip address in that network, this address will be the local hosts default gateway 3. Find the DNS server ip address learned by the router using DHCP client services, use the show dhcp server exec command, the router will then be able to inform the DNS sever ip address to the hosts in the local LAN 4. Find the domain name, again with the show dhcp server exec command Step 4. Configure DHCP server Pleas refer to page 556 and 557 for SDM DHCP server configuration wizards . which asks for the user inputs DHCP pool and DHCP setting learned in the previous steps.

17

Internet Access Router Verification Steps to perform basic verification of the installation of the access routers.common items to check when troubleshooting access router installation Step 1. Go to a PC on the local LAN and open a web page, if it works fine, then the access router configurations worked, otherwise go to step 2. Step 2. Try the ipconfig/all , command prompt command to verify the host has the correct IP address, dhcp settings, DNS setting as per the configured DHCP server configurations on the router, otherwise try ipconfig/release and ipconfig/renew commands to lease a new ip address. Step 3. Check the cabling and inside interface and outside interface as per the PAT configurations Step 4. Test the PAT functionality by generating traffic from a local pc to a host in the network EXEC commands on the access router for configuration verification Show ip dhcp binding lists ip addresses assigned on the local lan Show ip nat translation lists the NAT translation table entries Clear ip nat translation * - clears the NAT translation table entries Please refer to page 558 for a output listing of the above commands Definitions Cisco Router and Security Device Manager : Administrative web based interface on a router, that allows for configuration and monitoring of a router, including the configuration of DHCP, and NAT/PAT. Please refer to page540 for the Chapter 17 WAN configuration quiz.

18