NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI

Garment Defect Analysis

of a Denim Trouser
Faculty Name : Ms. Girija Jha

UG-TECHNOLOGY, SEMESTER-IV

Indranil Saha (07)

 Index
Title Page
 Introduction 3
 Style Description 5
 Defect Analysis 7
o Various Probable Defects (including trim defects) 7

o Pre Production Defects 8

 Pattern Making Defects 8
 Spreading Defects 9
 Cutting Defects 9
o Production Defects 11

o Post Production Defects 15

 Defect Checklist in the Garment 18
o Production Defects 18
o Post Production Defects 20
 Introduction
For every industry or business, to get increased sales and better name amongst consumers and fellow companies it is important to
maintain a level of quality. In the garment industry quality control is practiced right from the initial stage of sourcing raw materials to the stage
of final finished garment. For textile and apparel industry product quality is calculated in terms of quality and standard of fibres, yarns, fabric
construction, color fastness, surface designs and the final finished garment products. However quality expectations for export are related to the
type of customer segments and the retail outlets. There are a number of factors on which quality fitness of garment industry is based such as –
performance, reliability, durability, visual and perceived quality of the garment. Quality needs to be defined in terms of a particular framework
of cost.
The national regulatory quality certification and international quality Programs like ISO 9000 series lay down the broad quality
parameters based on which companies maintain the export quality in the garment and apparel industry. Here some of main fabric properties
that are taken into consideration for garment manufacturing for export basis:

 Overall look of the garment.

 Right formation of the garment.
 Feel and fall of the garment.
 Physical properties.
 Color fastness of the garment.
 Finishing properties.
 Presentation of the final produced garment.

There are certain quality related problems in garment manufacturing that should not be over looked:
 Sewing defects - Like open seams, wrong stitching techniques used, same color garment, but usage of different color threads on the
garment, miss out of stitches in between, creasing of the garment, erroneous thread tension and raw edges are some sewing defects
that could occur so should be taken care of.

 Color effects - Color defects that could occur are – difference of the color of final produced garment to the sample shown, accessories
used are of wrong color combination and mismatching of dye amongst the pieces.
 Sizing defects - Wrong gradation of sizes, difference in measurement of a garment part from other, for example- sleeves of ‘XL’ size but
body of ‘L’ size. Such defects do not occur has to be seen too.

 Garment defects - During manufacturing process defects could occur like faulty zippers, irregular hemming, loose buttons, raw edges,
improper button holes, uneven parts, inappropriate trimming, and difference in fabric colors.
 Style Description
A stone-washed Denim Trouser
Front View Back View
Stone Washed Denim:
Stonewashed jeans are jeans that have been treated to produce a faded, worn appearance. This is usually accomplished either by washing the
jeans with pumice in a rotating drum, or also by using chemicals to create the appearance without the use of a rotating drum. Stonewashed
jeans were a popular fashion trend in the 1970s.In the 2000s stonewashed jeans were heavily distressed, with pre-made holes, frayed edges and
extensive fading caused by sandblasting.

Front Panel
 Waist Band
 Front Panel
 Zipper fly Panel
 Front Leg parts

Back Panel
 Waist Band
 Back Panel
 Back Leg Parts
 Defect Analysis
Various Probable Defects (including trim defects):
 Broken buttons
 Broken snaps
 Broken stitching
 Defective snaps
 Different shades within the same garment
 Dropped stitches
 Exposed notches
 Exposed raw edges
 Holes
 Inoperative zipper
 Loose / hanging sewing threads
 Misaligned buttons and holes
 Missing buttons
 Needle cuts / chews
 Open seams
 Pulled / loose yarn
 Stain
  Unfinished buttonhole
 Zipper too short

Pre production Defects

Pattern defects in garment:

Some parts of pattern are missing, probably because the marker did not include the correct number of parts.
Mixed parts, probably because the marker is not correctly labeled, resulting in a marriage of wrong sized parts.
Patterns not facing in correct direction on napped fabrics.
Not all patterns facing in same direction (either way) on a one-way fabric. Patterns not aligned with respect to the fabric
grain.

Poor line definition (e.g. too thick chalk; indistinctly printed line, perforated lay not powdered) leading to inaccurate cutting.
 Skimpy marking, caused by either the marker did not use the outside edge of the pattern; or the pattern was moved or
swung after partial marking to squeeze the pattern into a smaller space for economizing the fabric.

Marking back from miniature markers also can cause trouble unless the miniature marker making is in the hands of
experienced operators. Alternatively the full size pattern may be having worn out edges.

Generous marking, especially in combination with skimpy marking results in components being sewn together with puckering
and pleating.

When the marker is too wide, the garment parts at the edges of the lay get cut with bits missing.
Not enough knife clearance freedom. Wrong check matching, i.e. lines across the seam are not matching.
Wrong check boxing, i.e. checks are not showing a full or partial box across the seam.

Notches and drill marks omitted, indistinct or misplaced.

Spreading defects in garment:

 Not enough plies to cover quantity of garments required.

 Plies misaligned, resulting in garment parts getting cut with bits missing in some plies at the edge of the spread.

 Narrow fabric, causes garment parts at the edge of the lay getting cut with bits missing.
  Incorrect tension of plies, i.e. fabric spread too tight or too loose.

 This will result in parts not fitting in sewing, and finished garments not meeting size tolerances. Not all plies facing in correct
direction (whether 'one way' as with nap, or 'one way either way' as with some check designs). This happens when fabric is
not spread face down, face up, or face to face as required.

 Unacceptable damages in the garment parts. Parts not fully included owing to splicing errors.

 Spread distorted by the attraction or repulsion of plies caused by excessive static electricity.

 Plies are not spread accurately one above another for cutting. This results in mismatching checks.

Cutting defects in garment:

 Failure to follow the marker lines resulting in distorted garment parts.

 Top and bottom plies can be a different size if the straight knife is allowed to lean, or if a round knife is used on too high a
spread.

 Notches, which are misplaced too deep, too shallow, angled, omitted, or wrong type to suit fabric.

 Drill marks, which are misplaced, wrong drill to suit fabric, omitted, not perpendicular through the spread.

 Frayed edges, scorched or fused edges, caused by a faulty knife, not sharp enough, or rotating at too high a speed.

 Garment part damaged by careless use of knife, perhaps overrunning cutting previous piece. Marker incorrectly positioned
on top of spread.

 Garment parts have bits missing at edge of lay.

  If too tight or too loose then garment parts are distorted.

 Slits opened inaccurately or omitted.

Production Defects
Name of the Description Defect Picture Cause Remedy
defect
Broken Stitches Where the thread is Needle Cutting  Use a higher performance
being broken where one thread.
seam crosses another
seam (ex: bar tacks on  Use a larger diameter thread
top of waistband on operations where the
stitching) resulting in thread is being cut.
stitch failure.
  Make sure the proper stitch
balance is being used. (On a
chain stitch seam on denim,
normally a 60%/40%
relationship of Needle thread
to looper thread in the Seam
is maintained).

 Use needles with the correct

needle point.

 Change the needles at regular

intervals on operations where
the Needle Cuts are occurring
frequently.
Unraveling Seams This causes seam failure
unless the seam is Re
Generally occurs on
401 chain stitch  Use a high performance
stitched. seams where either thread that will minimize
the stitch has been broken stitches and skipped
broken or a skipped stitches;
stitch has occurred.
 Insure proper machine
maintenance and sewing
machine adjustments;

 Observe sewing
operators for correct material
handling techniques.
Re Stitched Seams Where there is a "splice"
on the stitch line. If this
1. Thread breaks or
thread run-out during  Use a better quality sewing
occurs on Topstitching, sewing; or thread. This may include
then the seam does not going to a higher
appear to be nice. 2. Cut or broken performance thread designed
stitches during a to minimize sewing
subsequent interruptions.
treatment of the
finished product (I.e.,
stone washing).
 Insure proper machine
maintenance and sewing
machine adjustments;
  Make sure sewing machines
are properly maintained and
adjusted for the fabric and
sewing operation.

 Observe sewing operators for

correct material handling
techniques.
Skipped Stitches Skips are usually found
where one seam crosses
Where the stitch
forming device  Use core spun thread.
another seam and most misses the needle
of the time occurs right
before or right after the
loop or the needle
misses the looper
 Use minimum thread
tension to get a balanced
heavy thickness. loop.
stitch.

 Use the ideal foot, feed

and plate that help to minimize
flagging.

 Training sewing
operators NOT to stop on the
thickness.

 Make sure the machine

is feeding properly without
stalling.

 Make sure the machine

is not back feeding.
Ragged / Inconsistent Where the edge of the  Make sure the sewing
Edge seam is either extremely machine knives are
"ragged" or "rolls" inside sharpened and changed
the stitch. often;

 The knives should be

adjusted properly in
relationship to the "stitch
tongue" on the needle plate
to obtain the proper seam
width or width bite.
Wavy Seams on
Stretch Denim
Where the seam does
not lay flay and is wavy
Due to the fabric
stretching as it was  Use minimum presser foot
sewn or during pressure
subsequent
laundering and
handling operations.
 Instruct sewing operators to
use proper handling
techniques and not stretch
the fabric as they are
making the seam.

 Where, available, use

differential feed to
compensate for the stretch
of the fabric.
Ropy Hem Where hem is not laying Usually caused by  Instruct the sewing operator
flat and is skewed in poor operator to make sure they get the
appearance handling. hem started correctly in the
folder before they start
sewing. Also, make sure
they don't hold back
excessively as the seam is
being sewn.

 Use minimum roller or

presser foot pressure.
Twisted Legs Is where the side seam Usually caused by  Instruct the sewing
twists around to the front poor operator operator to match the front and
of the pant and distorts handling. back properly so they come
the appearance of the out the same length.
jeans. Sometimes notches are used
to insure proper alignment.

 They should NOT trim

off the front or back with
scissors to make them come
out the same length.

 Make sure the cut parts

are of equal length coming to
the assembly operation.

 Check fabric quality and

cutting for proper skew.

 Make sure the sewing

machine is adjusted properly
for uniform feeding of the top
and bottom plies.
Disappearing Stitches Is where the thread  Shorter  Use a heavier thread
in Stretch Denim looks much smaller on stitch length size on topstitching.
seams sewn in the warp  Poor
direction than in the weft operator  Go to a longer stitch
direction of the fabric. handling length (from 8 to 6 spi).

 Make sure the thread

tensions are as loose as
possible so the thread sits on
top of the fabric rather than
burying in the fabric on
seams sewn in the warp.
 Post Production Defects
Name of Description Defect Picture Cause Remedy
the defect
Thread discoloration A common discoloration It is the thread picks  Use thread with proper
after Laundry would be the pick-up of a up the indigo dyes color fastness characteristics.
greenish or turquoise from the fabric giving
tint. the thread a 'dirty'  Correct PH level (too
appearance. low) and Water Temperature
(too low) during laundry.

 Use the proper

chemicals & laundry cycles.

 Use Denimcol PCC in

wash or similar additive.

 Do not overload washers

with too many garments at
one time.
Poor Colorfastness It changes to a different It is where the thread  Use thread with proper
after Laundry color altogether. does not wash down color fastness characteristics.
consistently in the
garment  Use threads from the
same thread supplier and do
not mix threads in a garment.

 Always do preproduction
testing on denim garments
using new colors to assure
that they will meet your
requirements.

 Make sure sewing

operators select thread by
type and color number and
do not just pick a thread off
the shelf because it looks
close in color.
Sagging or Rolling
Pockets
Where the pocket does
not lay flat and rolls over
 Improper
cutting of
 Make sure the sewing
after laundering. Pocket operators are not holding back
excessively when setting the
front pocket.
 Improper
folder
functioning  Make sure the hem is
formed properly and that
 Excessive excessive fabric is not being
holding put into the folder that will
back of cause the hem to roll over.
pocket by
the operator  Check to make sure
pocket is cut properly and that
pocket curve is not too deep.

 Use a reinforcement
tape on the inside of the
pocket that may help prevent
the front panel from stretching
along the bias where the front
pocket is set.

 The type and weight of

denim, along with the fabric
construction, may contribute to
this problem.
Broken Stitches (I) Where thread is being Chemical  Use a higher performance
compromised by the Degradation thread that has greater
chemicals used during resistance to chemical
laundering resulting in degradation.
loss or change of color
and seam failure.  It is recommended to go to
larger thread sizes when the
Denim Garments will be
subject to harsh chemical
washes.

 To achieve the best

laundering results make sure
that the water temperatures
and PH Levels are correct
and that the proper amounts
and sequence of chemical
dispersion are within
guidelines.

 Make sure the garments are

being rinsed properly to
neutralize the chemicals in
the fabric
.
 Monitor the drying process,
cycle times, and
temperatures to make sure
they are correct so that the
best possible garment quality
can be achieved.
Broken Stitches (II) Where thread on the
stitch line is broken
due to abrasion
during stone-  Use a higher performance
during stone-washing, washing, sand thread;
sand blasting, hand blasting, hand
sanding, etc. Broken sanding, etc.  Use a larger diameter thread
stitches must be repaired on operations where excessive
by re stitching over the abrasion is occurring.
top of the stitch-line.

 Make sure stitches are balance

properly, susceptible to
 abrasion.

 Monitor the Finishing Cycle for

compliance to specifications.

Defect Checklist in the garment

Production Defects
Name of the defects Present/Absent
Broken Stitches Absent
Unraveling Seams Absent
Re stitched Seams Present
Skipped Stitches Present

Ragged / Inconsistent Edge Present

Wavy Seams on Stretch Denim Present

Ropy Hem Absent

Twisted Legs Present
Disappearing Stitches in Stretch Denim Present

Post Production Defects

Name of the defect Present/Absent
Thread discoloration after Laundry Present

Poor Colorfastness after Laundry Absent

Sagging or Rolling Pockets Absent
Broken Stitches (I) Absent
Broken Stitches (II) Absent