Scribd
Upload
24 views

Feedback Control Systems: Figure 8.1 A Transfer Function Example

This document introduces feedback control systems and transfer functions. It discusses how transfer functions can represent systems as a ratio of output to input using constants and differential operators. Transfer functions have a direct relationship to differential equations, with the homogeneous equation becoming the denominator and non-homogeneous solution becoming the numerator. Examples of first and second-order transfer functions are shown, relating them to common differential equations. The objectives are to represent systems with block diagrams, select controller parameters to meet design objectives, and understand transfer functions and feedback controllers.

Uploaded by

rao abdul hannan
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
24 views

Feedback Control Systems: Figure 8.1 A Transfer Function Example

This document introduces feedback control systems and transfer functions. It discusses how transfer functions can represent systems as a ratio of output to input using constants and differential operators. Transfer functions have a direct relationship to differential equations, with the homogeneous equation becoming the denominator and non-homogeneous solution becoming the numerator. Examples of first and second-order transfer functions are shown, relating them to common differential equations. The objectives are to represent systems with block diagrams, select controller parameters to meet design objectives, and understand transfer functions and feedback controllers.

Uploaded by

rao abdul hannan
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 2

8.

FEEDBACK CONTROL SYSTEMS


8.1 INTRODUCTION
Every engineered component has some function. A function can be described as a
transformation of inputs to outputs. For example it could be an amplifier that accepts a
signal
from a sensor and amplifies it. Or, consider a mechanical gear box with an input and
output shaft. A manual transmission has an input shaft from the motor and from the
shifter. When analyzing systems we will often use transfer functions that describe a
system
as a ratio of output to input.
8.2 TRANSFER FUNCTIONS
Transfer functions are used for equations with one input and one output variable.
An example of a transfer function is shown below in Figure 8.1. The general form calls
for
output over input on the left hand side. The right hand side is comprised of constants and
the ’D’ operator. In the example ’x’ is the output, while ’F’ is the input.
Figure 8.1 A transfer function example
Topics:
Objectives:
• To be able to represent a control system with block diagrams.
• To be able to select controller parameters to meet design objectives.
• Transfer functions, block diagrams and simplification
• Feedback controllers
• Control system design
output
input
---------------- = f(D)
The general form
x
F
--- 4 + D
D2 + 4D + 16
= ---------------------------------
An example
feedback control - 8.2
If both sides of the example were inverted then the output would become ’F’, and
the input ’x’. This ability to invert a transfer function is called reversibility. In reality
many systems are not reversible.
There is a direct relationship between transfer functions and differential equations.
This is shown for the second-order differential equation in Figure 8.2. The homogeneous
equation (the left hand side) ends up as the denominator of the transfer function. The
nonhomogeneous
solution ends up as the numerator of the expression.
Figure 8.2 The relationship between transfer functions and differential equations for a
mass-spring-damper example
The transfer function for a first-order differential equation is shown in Figure 8.3.
As before the homogeneous and non-homogeneous parts of the equation becomes the
denominator and the numerator of the transfer function.
x·· 2 nx ·  n
+ + 2x
f
M
= ----
xD2 2  nxD  n
2+ + x
f
M
= ----
x D2 2  nD  n
2( ++ ) f
M
= ----
x
f
--
1
M
 ----

D2 2  nD  n
2++
= -------------------------------------------
particular
homogeneous
 n

Natural frequency of system - Approximate frequency of
control system oscillations.
Damping factor of system - If < 1 then underdamped, and the system
will oscillate. If =1 critically damped. If < 1 overdamped, and never
any oscillation (more like a first-order system). As damping factor
approaches 0, the first peak becomes infinite in height.
feedback control - 8.3
Figure 8.3 A first-order system response
8.3 CONTROL

You might also like