Scribd
Upload
3K views

Ansys Code For RCC

The document provides code for modeling reinforced concrete in ANSYS. It includes commands for defining the concrete material properties using solid65 elements, rebar material properties using link180 elements, and tying the nodes between the elements. It also includes preprocessor commands to select the relevant elements and tie the nodes, and postprocessor commands to view results like crack patterns.

Uploaded by

Anvar Va
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
3K views

Ansys Code For RCC

The document provides code for modeling reinforced concrete in ANSYS. It includes commands for defining the concrete material properties using solid65 elements, rebar material properties using link180 elements, and tying the nodes between the elements. It also includes preprocessor commands to select the relevant elements and tie the nodes, and postprocessor commands to view results like crack patterns.

Uploaded by

Anvar Va
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 10

ANSYS Reinforced Concrete Beam (RC BEAM) - Static Structural by DrDalyO

CONCRETE COMMANDS:
ET,MATID,SOLID65
R,MATID,0,0,0,0,0,0
RMORE,0,0,0,0,0
MP,EX,MATID,29250
MP,PRXY,MATID,0.2
MPTEMP,MATID,0
TB,CONCR,MATID,1,9
TBTEMP,22
TBDATA,1,0.3,0.8,1.5,25
TB,MISO,MATID,1,35,0
TBTEMP,22
TBPT,,0.0001,2.925
TBPT,,0.0002,5.7
TBPT,,0.0003,8.325
TBPT,,0.0004,10.8
TBPT,,0.0005,13.125
TBPT,,0.0006,15.3
TBPT,,0.0007,17.325
TBPT,,0.0008,19.2
TBPT,,0.0009,20.925
TBPT,,0.001,22.5
TBPT,,0.0011,23.925
TBPT,,0.0012,25.2
TBPT,,0.0013,26.325
TBPT,,0.0014,27.3
TBPT,,0.0015,28.125
TBPT,,0.0016,28.8
TBPT,,0.0017,29.325
TBPT,,0.0018,29.7
TBPT,,0.0019,29.925
TBPT,,0.002,30
TBPT,,0.0021,30
TBPT,,0.0022,30
TBPT,,0.0023,30
TBPT,,0.0024,30
TBPT,,0.0025,30
TBPT,,0.0026,30
TBPT,,0.0027,30
TBPT,,0.0028,30
TBPT,,0.0029,30
TBPT,,0.003,30
TBPT,,0.0031,30
TBPT,,0.0032,30
TBPT,,0.0033,30
TBPT,,0.0034,30
TBPT,,0.0035,30

REBAR COMMANDS:
ET,MATID,LINK180
MPDATA,EX,MATID,,2e5
MPDATA,PRXY,MATID,,0.3
TB,BISO,MATID,1,2
TBDATA,,460,2100
R,MATID,12,,0

FRP COMMANDS:
ET,MATID,SOLID45
MPDATA,EX,MATID,,2e5
MPDATA,EY,MATID,,2e5
MPDATA,EZ,MATID,,2e5
MPDATA,PRXY,MATID,,0.3
MPDATA,PRXZ,MATID,,0.3
MPDATA,PRYZ,MATID,,0.3
MPDATA,GXY,MATID,,2e5
MPDATA,GXZ,MATID,,2e5
MPDATA,GYZ,MATID,,2e5
TB,BISO,MATID,1,2
TBDATA,,460,2100
R,MATID,12,,0

PRE PROCESSOR COMMANDS:


/PREP7
ESEL,S,ENAME,,65
ESEL,A,ENAME,,180
ALLSEL,BELOW,ELEM
CEINTF,0.001,
ALLSEL,ALL
/SOLU
OUTRES,ALL,ALL

POST PROCESSOR COMMANDS:


/SHOW,png
/ANG,1,
/VIEW,1,0,0,0 !Use these values to change the view
/DEVICE,VECTOR,ON
SET,Last !Outputs final result set
PLCRACK

Please subscribe!!
By DrDalyo
https://www.youtube.com/user/drdalyo

for displaying only concrete structure


/PREP7
ESEL,S,ENAME,,65
/PREP7
ESEL,A,ENAME,,180
plnsol,u,sum
/PREP7
ESEL,S,ENAME,,65
ESEL,A,ENAME,,180

Respected All,
Thank you very much for your replies.
As Mr.Peter Barrett said I modelled my concrete beam with solid65
element and reinforcements with link180 elements and asssigned these
following properties in ansys workbench.
"
ET,MATID,SOLID65
R,MATID,0,0,0,0,0,0
RMORE,0,0,0,0,0
MP,EX,MATID,24267.688
MP,NUXY,MATID,0.2

TB,MISO,MATID,1
TBTEMP,22
TBPT,DEFI,0.0002219,5.3845
TBPT,DEFI,0.001083,19.9843
TBPT,DEFI,0.00174,23.8956
TBPT,DEFI,0.002219,24.4764

TB,CONCR,MATID,1,9
TBTEMP,22
TBDATA,1,0.3,1,3.081,19.9391
and for reinforcements as
ET,matid,LINK180
MPDATA,EX,matid,,2e5
MPDATA,PRXY,matid,,0.3
TB,BISO,matid,1,2
TBDATA,,355,2100,,,,
R,matid,71.252, ,0

and then I combined the nodes of the link elements and solid65 using
these commands

/PREP7
ESEL,S,ENAME,,65
ESEL,A,ENAME,,180
ALLSEL,BELOW,ELEM
CEINTF,0.00001,
ALLSEL,ALL
/SOLU

and I applied a displacement of 20mm. I got a converged solution. But


as I need to see the crack patterns , I transfered the DS.DAT from WB
to ansys mechanical APDL. I can see the element solutions, But unable
to see the cracks at each step.Could you please tell me How I could
solve this problem and view the cracks at different stages.
Thank you very much for your help.

Regards
Rukmani Ganesan
Bauhaus-Universitt Weimar
Natural Hazards and Risks in Structural Engineeing
Tel.: +49(0)176/55446995
E-Mail: [email protected]
[email protected]

FINAL CODES
CONCRETE COMMANDS:
ET,MATID,SOLID65
TB,CONCR,MATID,1,9
TBTEMP,22
TBDATA,1,0.3,0.8,1.5,25

REBAR COMMANDS:
ET,MATID,LINK180

PRE PROCESSOR COMMANDS:


/PREP7
ESEL,S,ENAME,,65
ESEL,A,ENAME,,180
ALLSEL,BELOW,ELEM
CEINTF,0.001,
ALLSEL,ALL
/SOLU
OUTRES,ALL,ALL

POST PROCESSOR COMMANDS:


/SHOW,png
/ANG,1,
/VIEW,1,0,0,0 !Use these values to change the view
/DEVICE,VECTOR,ON
SET,Last !Outputs final result set
PLCRACK

selecting concrete and warp

/PREP7

ESEL,S,ENAME,,45, 65

Modelling of RC beam with Ansys WorkBench (Alaa Elsisi)


Concrete Command
ET,matid,SOLID65

MPDATA,EX,matid,,2e4
MPDATA,PRXY,matid,,0.25
TB,CONC,matid,1,9,
TBTEMP,0
TBDATA,,0.2,0.8,3,30,,
TBDATA,,,,,,,

R,matid, , , , , , ,
RMORE, , , , , , ,
RMORE, ,
Steel Command
ET,matid,LINK180
MPDATA,EX,matid,,2e5
MPDATA,PRXY,matid,,0.3
TB,BISO,matid,1,2,
TBDATA,,350,2000,,,,
R,matid,200, ,0

Solution Commands

/PREP7
ESEL,S,ENAME,,65
ESEL,A,ENAME,,180
ALLSEL,BELOW,ELEM
CPINTF,ALL,0.00001,
ALLSEL,ALL
/SOLU

TB,MISO,MATID,1,5,0
TBTEMP,22
TBPT,,0.0003,7.5
TBPT,,0.00054,12.68
TBPT,,0.00124,22.39
TBPT,,0.00184,24.91
TBPT,,0.00237,25

TBDATA,,0.3,0.5,0.38,38,0,0
TBDATA,,0,0,0.3,,,

VALID.
concrete
ET,MATID,SOLID65
R,MATID,0,0,0,0,0,0
RMORE,0,0,0,0,0
MP,EX,MATID,30000
MP,PRXY,MATID,0.15
MPTEMP,MATID,22
TB,CONCR,MATID,1,9
TBTEMP,22
TBDATA,,0.3,0.5,3.8,38,0,0
TBDATA,,0,0,0.3,,,
TB,MISO,MATID,1,9,0
TBTEMP,22
TBPT,,0.0004,12
TBPT,,0.00095,25
TBPT,,0.00127,30
TBPT,,0.0015,33
TBPT,,0.0017,35
TBPT,,0.0020,37
TBPT,,0.00233,38
TBPT,,0.0025,38
TBPT,,0.003,38

steel
ET,MATID,LINK8
TB,BISO,MATID,1,2
TBDATA,,240,10000
R,MATID,50.24,,0
steel 2
ET,MATID,LINK8
TB,BISO,MATID,1,2
TBDATA,,360,10000
R,MATID,78.5,,0

preprocessor
/PREP7
ESEL,S,ENAME,,65
ESEL,A,ENAME,,8
ALLSEL,BELOW,ELEM
CEINTF,0.001,
ALLSEL,ALL
/SOLU
OUTRES,ALL,ALL

post processing
/SHOW,png
/ANG,1,
/VIEW,1,0,0,0 !Use these values to change the view
/DEVICE,VECTOR,ON
SET,Last !Outputs final result set

PLCRACK

You might also like