Scribd
Upload
383 views8 pages

Under Reamed Pile

This document provides design details for an under-reamed pile and pile cap. It specifies the pile will have one under-ream, a 0.4m diameter stem, 1m diameter under-ream, and 3.5m length. It requires 6 longitudinal bars of 12mm diameter spaced at 300mm. The pile is designed to support a maximum 200kN axial load, 30kN tension, and 30kN lateral load. The pile cap is also designed to support these loads from the single pile. Reinforcement details and checks are provided to verify the design meets code requirements.

Uploaded by

Rassal Karim
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
383 views8 pages

Under Reamed Pile

This document provides design details for an under-reamed pile and pile cap. It specifies the pile will have one under-ream, a 0.4m diameter stem, 1m diameter under-ream, and 3.5m length. It requires 6 longitudinal bars of 12mm diameter spaced at 300mm. The pile is designed to support a maximum 200kN axial load, 30kN tension, and 30kN lateral load. The pile cap is also designed to support these loads from the single pile. Reinforcement details and checks are provided to verify the design meets code requirements.

Uploaded by

Rassal Karim
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 8

DESIGN OF UNDER REAMED PILE

REFERENCE IS 2911 (Part III)-1980 & IS 456:2000


PROJECT NO.
CLIENT
Column Designation
SUPPORT REACTIONS
Fy
=
Maximum Axial Compressive Load
200 kN
Fy (-)
=
Maximum Tension
30 kN
Fx
=
Maximum Lateral Load in x direction
30 kN
Fz
=
Maximum Lateral Load in z direction
0 kN
Maximum Moment in x direction
Mx
=
0 kN
Maximum Moment in z direction
Mz
=
0 kN
CAST IN SITU PILE DETAILS (FROM TABLE 1, IS 2911 (Part III) -1980)
No. of under-reams
=
1
Diameter of stem
d
=
0.4 m
Diameter of under ream
Du
=
1m
Length of pile
L
=
3.5 m
Diameter of longitudinal reinforcement
,long
=
12 mm
Number of longitudinal reinforcements
N, long
=
6 nos.
,trans
=
Diameter of transverse reinforcement
6 mm
N, long
=
Spacing of transverse reinforcements
300 mm
Puc,safe
=
Safe axial load in compression
225 kN
Put,safe
=
Safe uplift load
137 kN
Pul,safe
=
Safe lateral load
33 kN
PILE GROUP
n, reqd
=
No. of piles required in each group
1
n
=
No. of piles given in each group
3
S
=
Spacing of piles in the goup
2m
REINFROCEMENT CHECK
INPUTS
Axial Load
Pu
=
200 kN
Moment in x direction
Mx
=
0 kNm
Moment in z direction
Mz
=
0 KNm
Lateral Load in x direction
Fx
=
30 kN
Lateral Load in z direction
Fz
=
0 kN
Maximum Tension
T
=
30 kN
Factored Axial Load
Puf
=
100 kN
Factored Moment in x direction
Mx'
=
0 kNm
Factored Moment in z direction
Mz'
=
0 KNm
Lateral Load in x direction
Fx'
=
15 kN
Lateral Load in y direction
Fz'
=
0 kN
Characteristic strength of concrete
fck
=
25 N/mm2
Characteristic strength of steel
fy
=
415 N/mm2
Column Dimensions
Length of the column
L
=
3500 mm

Diameter
Effective length ratio
Clear cover
Diameter of bar
Diameter of lateral ties
Effective cover
Effective length of column in x
Effective Length of column in y
Minimum eccentricity in x
Minimum eccentricity in y
Applied eccentricity in x
Applied eccentricity in y
Calculations
Factored Moment due to lateral load in x
Factored Moment due to lateral load in y
Factored Moment in x direction
Factored Moment in z direction
Total Moment in x direction
Total Moment in z direction
Resultant Uniaxial Moment
d'/D
Pu/(fckD2)
Mu/(fckD3)
p/fck
Percentage of reinforcement required
Area of reinforcement required
Number of bars required
Number of bars provided
Moment Capacity Calculations and check
Area of steel provided
Effective cover
p/fck
Pu/(fckD)
d'/D
Mux1/(fckD3)
Moment capacity in x direction
Moment capacity in y direction
Maximum Axial load capacity
Pu/Puz
n
(/1)^n + (/y1)
^n 1

D
k
dc

t
d'
lex
ley
ex,min
ey,min
ex
ey

=
=
=
=
=
=
=
=
=
=
=
=

Mfx
Mfz
Mx
Mz
Mux
Muy
Mu

=
=
=
=
=
=
=
=
=
=
=
=
=
=
=

p,reqd
Ast,reqd
Nr
Np

400 mm
1.2
50 mm
12 mm
8 mm
64.0 mm
4200 mm
4200 mm
20.00 mm
20.00 mm
525.00 mm
20.00 mm
52.5 kNm
0 kNm
0 kNm
0 KNm
52.5 kNm
0 kNm
60.38 kNm
0.16
0.025
0.038
0.03
0.75 %
942.4778 mm2
8 nos.
8 nos.

Ast
d'

=
904 mm2
=
64.00 mm
=
0.029
=
0.03
=
0.16
=
0.110
Mux1
=
176 kNm
Muy1
=
176 kNm
Values of Puz and n
Puz
=
1685.01 kN
=
0.06
=
1.000
Safety under biaxial loading
SAFE UNDER APPLIED LOAD

SAFE UNDER TENSION


Spacing of lateral ties

Sv

300 mm

INPUT
OUTPUT
CHECK

2000

Unfactored
Unfactored
Unfactored
Unfactored
Unfactored
Unfactored

on
on
on
on
on

single
single
single
single
single

Loads
Loads
Loads
Loads
Loads
Loads

pile
pile
pile
pile
pile

DIA OK

ok
ok

Refer SP16
OK

Puz=0.45fckAg+(0.75fy-0.45fck)Asc

Design of Pile Caps


REFERENCE IS 2911 (Part III)-1980 & IS 456:2000
PROJECT NO.
CLIENT
Column Designation
SUPPORT REACTIONS
Maximum Axial Compressive Load
Maximum Tension
Maximum Lateral Load in x direction
Maximum Lateral Load in z direction
Maximum Moment in x direction
Maximum Moment in z direction

Fy
Fy (-)
Fx
Fz
Mx
Mz

=
=
=
=
=
=

200 kN
30 kN
30 kN
0 kN
0 kN
0 kN

000

Unfactored
Unfactored
Unfactored
Unfactored
Unfactored
Unfactored

Loads
Loads
Loads
Loads
Loads
Loads

You might also like