Induction Generator

An induction generator produces electricity when its rotor is spun faster than its synchronous speed by a prime mover like a turbine. It operates similar to an induction motor but with the rotor moving faster than the rotating magnetic field, causing current to be induced in the stator coils and power to be generated. An external source is needed to provide excitation current for the stator flux. Induction generators are useful for applications with variable speed like wind turbines due to their simple and rugged design requiring no brushes or commutators. They can be connected to the electric grid or operate standalone using a capacitor bank to provide reactive power excitation.

Uploaded by

AmarjeetRanjan

Available Formats

Download as DOCX, PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

73 views

Induction Generator

Uploaded by

AmarjeetRanjan

Available Formats

Download as DOCX, PDF, TXT or read online on Scribd

You are on page 1/ 5

Induction generator

From Wikipedia, the free encyclopedia

An induction generator or asynchronous generator is a type of AC electrical generator that uses
the principles of induction motors to produce power. Induction generators operate by
mechanically turning their rotor faster than the synchronous speed. A regular AC asynchronous
motor usually can be used as a generator, without any internal modifications. Induction
generators are useful in applications such as mini hydro power plants, wind turbines, or in
reducing high-pressure gas streams to lower pressure, because they can recover energy with
relatively simple controls.
An induction generator must be excited with a leading voltage. This is usually done by
connection to an electrical grid; sometimes, however, they are self-excited by using phase
correcting capacitors. Because of this, induction generators cannot usually "black start" a deenergized distribution system.

Contents

1 Principle of operation
o 1.1 Excitation
o 1.2 Active power
o 1.3 Required capacitance
o 1.4 Torque vs. slip

2 Grid and stand-alone connections

3 Use of induction generators

4 Example application

5 See also

6 References

7 External links

Principle of operation

Induction generators and motors produce electrical power when their rotor is turned faster than
the synchronous speed. For a typical four-pole motor (two pairs of poles on stator) operating on a
60 Hz electrical grid, the synchronous speed is 1800 rotations per minute. The same four-pole
motor operating on a 50 Hz grid will have a synchronous speed of 1500 RPM. The motor
normally turns slightly slower than the synchronous speed; the difference between synchronous
and operating speed is called "slip" and is usually expressed as per cent of the synchronous
speed. For example, a motor operating at 1450 RPM that has a synchronous speed of 1500 RPM
is runnign at a slip of +3.3%.
In normal motor operation, stator flux rotation is faster than the rotor rotation. This causes the
stator flux to induce rotor currents, which create a rotor flux with magnetic polarity opposite to
stator. In this way, the rotor is dragged along behind stator flux, with the currents in the rotor
induced at the slip frequency.
In generator operation, a prime mover (turbine, engine) drives the rotor above the synchronous
speed (negative slip). The stator flux still induces currents in the rotor, but since the opposing
rotor flux is now cutting the stator coils, an active current is produced in stator coils and the
motor now operates as a generator, sending power back to the electrical grid.

Excitation

Equivalent circuit of induction generator

An induction machine requires externally supplied armature current; it cannot start on its own as
a generator. Because the rotor field always lags behind the stator field, the induction machine
always "consumes" reactive power, regardless of whether it is operating as a generator or a
motor.
A source of excitation current for magnetizing flux (reactive power) for the stator is still
required, to induce rotor current. This can be supplied from the electrical grid or, once it starts
producing power, from the generator itself. The rotating magnetic flux from the stator induces
currents in the rotor, which also produces a magnetic field. If the rotor turns slower than the rate
of the rotating flux, the machine acts like an induction motor. If the rotor is turned faster, it acts
like a generator, producing power.

Active power

Active power delivered to the line is proportional to slip above the synchronous speed. Full rated
power of the generator is reached at very small slip values (motor dependent, typically 3%). At
synchronous speed of 1800 rpm, generator will produce no power. When the driving speed is
increased to 1860 rpm, full output power is produced. If the prime mover is unable to produce
enough power to fully drive the generator, speed will remain somewhere between 1800 and 1860
rpm range.

Required capacitance
A capacitor bank must supply reactive power to the motor when used in stand-alone mode.The
reactive power supplied should be equal or greater than the reactive power that the machine
normally draws when operating as a motor. Terminal voltage will increase with capacitance, but
is limited by iron saturation.

Torque vs. slip

The basic fundamental of induction generators is the conversion between mechanical energy to
electrical energy. This requires a higher shaft rotating speed than the synchronous speed. An
external torque is required to be applied to the rotor, which generates electric power. However,
indefinitely increasing torque doesn't lead to an indefinite increase in power generation. The
rotating magnetic field torque excited from the armature works to counter the motion of the rotor
and prevent overspeed because of induced motion in the opposite direction. As the speed of the
motor increases the counter torque reaches a max value of torque (breakdown torque) that it can
operate until before the operating conditions become unstable. Ideally, induction generators work
best in the stable region between the no-load condition and maximum torque region.

Grid and stand-alone connections

Typical connections when used as a standalone generator

In induction generators, the reactive power required to establish the air gap magnetic flux is
provided by capacitor bank connected to the machine in case of stand alone system and in case
of grid connection it draws reactive power from the grid to maintain its air gap flux. For a grid
connected system, frequency and voltage at the machine will be dictated by the electric grid,
since it is very small compared to the whole system. For stand-alone systems, frequency and
voltage are complex function of machine parameters, capacitance used for excitation, and load
value and type.

Induction generator in grid connected operation

Use of induction generators

Induction generators are often used in wind turbines and some micro hydro installations due to
their ability to produce useful power at varying rotor speeds. Induction generators are
mechanically and electrically simpler than other generator types. They are also more rugged,
requiring no brushes or commutators.
Induction generators are particularly suitable for wind generating stations as in this case speed is
always a variable factor. Unlike synchronous motors, induction generators are load-dependent
and cannot be used alone for grid frequency control.

Example application
We must use 10 hp, 1760 r/min, 440 V, 3 phase induction motor as an asynchronous generator.
Full-load current of the motor is 10 A and full-load power factor is 0.8.
Required capacitance per phase if capacitors are connected in delta:
Apparent power S = 3 E I = 1.73 * 440 * 10 = 7612 VA
Active power P = S cos = 7612 * 0.8 = 6090 W
Reactive power Q =

= 4567 VAR

For machine to run as an asynchronous generator, capacitor bank must supply minimum 4567 / 3
phases = 1523 VAR per phase. Voltage per capacitor is 440 V because capacitors are connected
in delta.
Capacitive current Ic = Q/E = 1523/440 = 3.46 A
Capacitive reactance per phase Xc = E/I = 127
Minimum capacitance per phase:
C = 1 / (2**f*Xc) = 1 / (2 * 3.141 * 60 * 127) = 21 microfarads.
If load also absorbs reactive power, capacitor bank must be increased in size to compensate.

Prime mover speed should be used to generate frequency of 60 Hz:

Typically, slip should be similar to full-load value when machine is running as motor, but
negative (generator operation):
if Ns= 1800 we can choose N=Ns+40 rpm
Required prime mover speed N = 1800 + 40 = 1840 rpm.