Scribd
Upload
715 views

Inspection and Testing 05

The document outlines an inspection and testing program for fire protection equipment. It recommends appointing qualified staff to regularly inspect, test, and maintain equipment according to set schedules to ensure reliability. A customized inspection report and regular testing of sprinkler systems, valves, pumps, detectors and other equipment is advised to detect any issues before an emergency occurs. Proper identification, record keeping and prompt repair of deficiencies found is important for an effective fire protection program.

Uploaded by

Nasrul Adli
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
715 views

Inspection and Testing 05

The document outlines an inspection and testing program for fire protection equipment. It recommends appointing qualified staff to regularly inspect, test, and maintain equipment according to set schedules to ensure reliability. A customized inspection report and regular testing of sprinkler systems, valves, pumps, detectors and other equipment is advised to detect any issues before an emergency occurs. Proper identification, record keeping and prompt repair of deficiencies found is important for an effective fire protection program.

Uploaded by

Nasrul Adli
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 12

State of Minnesota

Inspection and Testing Program


Fire Protection Equipment
I. Introduction
Emergencies seldom give warning before they strike. Thus, it is essential that fire protection
equipment be inspected, tested, and maintained to be certain it is operable at all times.
Management, therefore, should establish an effective equipment inspection program.
A. Statement of Problem
Fire protection equipment, like all other equipment, deteriorates with time. It is also
vulnerable to external influences such as corrosive environments, tampering, accidental
damage, and careless use. Further, since fire protection equipment is used infrequently,
it must be inspected and tested regularly to prove its reliability and operability. It is far
better to detect an unsatisfactory condition prior to an emergency than it is to discover it
during the emergency.
B. Action Plan
A fire protection equipment inspection is intended to determine equipment operability
and should be performed as outlined in this section. In order to set up an effective
program, management shall:
1.

Appoint a qualified individual to monitor the program and report to management.

2. Select and train individuals with appropriate mechanical aptitude to conduct the
inspections and tests of fire protection equipment.
3.

Initiate a complete survey of the facility's fire protection equipment for the purpose
of developing a customized inspection report form. Examples of forms are attached.

4.

Establish effective procedures for reviewing the inspection reports.

5.

Initiate prompt action to correct any noted deficiencies.

6.

Establish contacts with sprinkler contractors for periodic testing and emergency
maintenance of fire protection equipment.

S:\RISK\WP\Gay\Web Site RMD\Source Documents\FireProtectionTesting2_2005.doc

State of Minnesota
C. Background
Once the qualified persons are selected, it is important that they be properly trained.
This training should include the following features:
1. Review of existing protection equipment and its maintenance, operation, and
testing techniques, and familiarization with installed fire protection equipment.
2.

Making copies of manufacturers' instruction manuals and other data available in a


centralized training file.

II. Elements of an Effective Self-Inspection Program


A. Trained Staff Designated to Establish and Implement the Program
The responsibility for supervision of fire protection systems rests with the Facilities
Manager and designated personnel responsible for the equipment. Employees
responsible for system supervision should be familiar with fire protection equipment
and know how to operate equipment during an emergency (verify necessary sprinkler
control valves are open in the fire area, know how to start and maintain fire pumps,
etc.). If your facility has several sprinkler systems, it is important that an up-to-date
sketch be maintained showing the location of sprinkler control valves. Proper inspection
records should be maintained.
Alternate personnel should be available to make fire prevention inspections when the
designated individual is ill or on vacation. Local management should support prompt
repair of equipment when deficiencies are noted.
If maintenance staff is not available and the services of a contractor are to be used to
perform maintenance and tests, the contractor should furnish a written report. The report
should include completed self-inspection forms. An employee should accompany the
contractor during the test to become familiar with the equipment in the event equipment
must be operated during an emergency.
B. Locking Sprinkler Control Valves
All fire protection system control valves shall be locked in the open position. Locks and
chains should be sturdy and resistant to breakage, except by heavy bolt cutters.
Breakaway and combination locks shall not be used. Distribution of keys should be kept
to a minimum and keys should be restricted to only those directly responsible for
maintaining the fire protection systems.
C. Self-Inspection Forms
Since the number, type, and complexity of fire protection systems will vary depending
on the size of your facility, customized self-inspection forms are needed for sprinkler

S:\RISK\WP\Gay\Web Site RMD\Source Documents\FireProtectionTesting2_2005.doc

State of Minnesota
control valves, portable fire extinguishers, fire pumps, dry pipe valves, etc. Such forms
not only serve as a guide for conducting inspections, but also provide a method of
proper record keeping. The inspector should carry the form and use it as a checklist. It
should be filled in as rounds are made, not after the completion of an inspection. A
sample form is provided at the end of this section.
D. Marking and Identification of Equipment
Sprinkler control valves should be numbered for inspection and identification purposes.
The number listed on the valve should correspond with the number on the inspection
form and fire diagram.
Valves should be plainly marked with the direction to open. If not marked by the
manufacturer, a sign should be posted near the valve indicating direction to open. If
underground curb box valves are used, a T wrench should be provided near the valve
with a sign indicating location of the valve.
E. Frequency of Inspection
The frequency of inspection of fire protection equipment depends on numerous factors.
For example, dry pipe systems should be checked daily in the winter; but less frequent
checks would be acceptable in the summer. The recommended frequency for testing and
maintenance of critical sprinkler system components appears on the attached schedule.

S:\RISK\WP\Gay\Web Site RMD\Source Documents\FireProtectionTesting2_2005.doc

State of Minnesota

Fire Protection Testing and


Inspection Schedule
Valves

All fire protection control valves (OSY - PIV - Butterfly) shall be locked
and chained in the open position.
All valves shall be visually inspected on a monthly basis to show they are
open and are not blocked.
All valves shall be exercised. Manually close and manually reopen every
6 months. Lubricate as needed.

Fire Pump

All fire pumps shall be started weekly by drop of pressure and allowed to
run for five minutes before placing back in automatic position (churn test).
All fire pumps shall be tested annually with a full flow test measuring
waterflow and pressure. (Qualified sprinkler company should perform the
test). Test results should be kept on file for review.

Alarms:

The following testing frequency shall be used for alarms:


Waterflow
Valve Tamper

Low Air
Pump Running
Electric Power to Pump
(Electric Pump)
Detectors
(Smoke and Heat)

Quarterly
Quarterly
Quarterly
Weekly
Monthly
Annually

Dry Pipe Valves

All dry pipe valves shall be tripped annually, with test results kept on file
for review.

FM-200

Annual contractor service

Anti-Freeze
Concentration

Annual test

Outside Local
Waterflow Alarms

Quarterly

S:\RISK\WP\Gay\Web Site RMD\Source Documents\FireProtectionTesting2_2005.doc

State of Minnesota

Fire Protection Testing


and Inspection Schedule
Private Hydrant and
Underground Flush

Annual flush shall be performed.

Extinguishers

Visually check monthly each extinguisher to confirm they


are charged, in place, and not blocked.
Annual service by qualified extinguisher company.

Inside Hose Connections

Visually check monthly to confirm they are in place and not


blocked.

Automatic Sprinkler Systems

Contract with qualified sprinkler contractor for annual


service and testing program.

2-inch Drain Test

Quarterly test of 2-inch drain on all risers. Record both static


and residual pressures with valve completely open.
Note: Cold weather may dictate this test be postponed due to
creating icy conditions outside building near drainpipe.
However, test sheet must be noted that test was not
completed due to cold weather.

Hydrants

Monthly visual check for accessibility and condition.

S:\RISK\WP\Gay\Web Site RMD\Source Documents\FireProtectionTesting2_2005.doc

You might also like