DEPARTMENT OF MECHANICAL ENGINEERING
SRI KALAHASTHEESWARA INSTITUTE OF TECHNOLOGY
SRIKALAHASTHI 517640 CHITTOOR(DIST.) AP
Automatic Two
Wheeler SelfSideStand System
Under Guidance of
P.Dileep M Tech
Presented by
Aravindh.K
12381A0304
Mechanical-A
Outline
Abstract
Previous methods for indications of lifting side
stand
Introduction
Construction
Components
Assembly
Working
Conclusion
2
In now a days two wheelers plays a important role in
transport. Due to humans carelessness accidents
happening. In that most important is due to forget to hold
the side stand in two wheeler.
Abstract
In earlier days Buzzer method and next gear
pedal methods are used as a remedy for this. But two
methods are not efficient. In now a days people are most
of them want simple operation.
So, we designed fully automatic self side stand
method. Its most efficient compared to other, While we
switch on the bike. By self start method is used start this
vehicle. By using this method we can relieve this side
stand from its position easily.
Methods for indicating of lifting
sidestand
Buzzer method
Gear Pedal method
Indicator method
DISADVANTAGE:
-
BUZZER METHOD
Buzzer method is always so high noise
pollution from any one two wheeler vehicle user
GEAR PEDAL METHOD
Gear pedal method is the all two wheeler
are not suitable trouble shooting problem.
INDICATOR METHOD
Indicator method is the electric device so
any one problem cannot reuse.
Introduction
The following are the source of accidents which
occurs due to carelessness of driver
Not wearing of Helmets
Ignore to maintain the speed within the safe
limits
Forget to retrieve the side stand
The table shows the percentage of accidents which occurred due to all these
factors
S.NO
DURING
THE YEAR
REASON FOR
ACCIDENT
%OF
ACCIDENTS
1.
2002-08
Does not obey Traffic
rules
22%
2.
2002-15
Does not maintain
speed limit
38%
3.
2008-15
Forgetting to lift side
stand
36%
Construction
The construction of this system is simple and efficient. The arrangement and
position of components makes the system to function. Each and every
component has its own property and responsibility.
The power obtained from the chain drive is transmitted to the appropriate
component without power loss. The systematic design of system is made in order
to consume only very low amount of power initially for few seconds to retrieve
the stand. Then the power consumption does not occurs after retrieving the stand.
Construction of the proposed automatic sidestand system consists of four
major components.
COMPONENTS
1.Axle
2.Sprocket pinion
3.Lifting lever
4.Pushing lever
SSRS(Sprocket Side Stand
Retrieval System)
This method can used in all types of two-wheelers
(e.g.mopeds, geared, non-geared, hand geared bikes).
Based on the working principle of two-wheeler i.e. the
power is generated in the engine and it transmits power
to the pinion and makes it to rotate.
The pinion transmits power to the rear wheel pinion and
makes the vehicle to move.
This is the basic principle followed in all type of two-
wheelers, based on this automatic side stand system is
designed because this system works by getting power
from chain drive
AXLE
Axle is the metallic rod made up of mild steel. It connects the lifting
lever and sprocket centrally. The one end of axle is welded with sprocket
and other end with lifting lever and thus power is transmitted from sprocket
to lifting lever. The axle is held by a holder. The holder is welded with the
frame. The holder is used to prevent vibration and to provide support to the
axle. The holder has small metallic tube and a rectangular metal plate.
SPROCKET
Sprocket is the major component of this system because it is power transmitting
device. It gets power from the chain drive and makes this system to work. It is the device
which transmits the linear motion of meshing chain drive into rotary motion by means of
the tooth found on it. The sprocket with ball bearings is said to be FREE WHEEL. The
anti-clockwise motion of the chain imports clockwise motion of the sprocket, which will
rotate in the same direction thus will the lifting lever.
LIFTING LEVER
The lifting lever is the rectangular rod made of MS-rod, which consists of two lifting
leaves which is mounted with the edge of axle. The lifting leaves should be parallel
to the sprocket pinion. The lifting lever is composed of two metal rods, where both
are welded at either sides of the axle. The free ends of the lifting leaves is tapered
well. The ends are machined well for tapered shape for smooth engaging with
pushing lever. This smooth engagement leads to proper retrieving of side stand.
PUSHING LEVER
pushing lever is the component pivoted centrally to the side stand.
The pushing lever is metallic rectangular plate, whose bottom end is bended
in shape of C and top end is welded with a small piece of rectangular rod.
This small piece of rectangular rod. This small piece of rod is used for
getting lifted by the lifting lever. Since this rod engages (or) lays over
tapered edge of lifting lever, thus the retrieving occur smoothly.
Types of Existing side
stands
MANUAL STAND
STAND WITH INDICATORS
STANDS WITH SPRINGS
Disadvantages of existing
side-stands
Accident Prone
Maximum Fatigue
Only indicate the position
Invention
Automatic side-stand
Revolutionary product
Self-retracting
Human-Error Nullified
Realization not required
There are two types of assembly for the functioning of the Side stand
Assembly
retrieve system:
INCITER ASSEMBLY
2. RETRIEVER ASSEMBLY
Inciter Assembly
Inciter assembly consists of axle, sprocket, and lifting lever.
The Sprocket is mounted on the centre of the axle and the lifting lever
is welded at the front side of axle.
This inciter assembly is main assembly because it receives the power
from the chain and incites the retriever assembly to retrieve the side
stand because this inciter assembly is kept under the chain as such that
the sprocket attached centrally with the axle get engage with chain drive
.
Retriever Assembly
Retriever assembly consists of pushing lever and side stand.
The pushing lever is centrally pivoted with the side stand as the pushing
levers tapered end is at top side and clamp is at the bottom.
1.
working
Sprocket meshing
Lifting lever
rotates
Down bottom line
of chain
Rightward linear
motion
Pushing lever
pushes
C clamp forces
Clockwise
rotation of
Sprocket
Side Stand
retrieves
Conclusion
Automatic side stand system is definitely a good retrieve system. Since the
setup is compact it does not affect the performance of the vehicle. Because of
this, the power is obtained from the chain drive.
Definitely this system could be used in all types of two-wheelers
(Tvs -XL, all
front, back, hand geared) for retrieving the side stand, it will be major system to
control accidents due side stand problem and protect the careless rider.
These system can be implemented in all types of bikes by changing small
variation in size. Moreover, the cost of this system is also very low and so it will
not affect the economic level. While compare to other system this automatic
side stand system will be the life saver.
Future cant be predicted
But it can
be made
Thank you
