Scribd
Upload
589 views

Self Balancing Robot

This document describes the design and operation of a self-balancing two-wheeled robot. It contains inertial sensors like a gyroscope and accelerometer to measure tilt. A microcontroller uses these sensor readings along with a balancing algorithm to determine if the motor needs to rotate clockwise or counterclockwise to counteract any tilt via a reaction wheel. The key parts are the inertial sensors, microcontroller, and actuator motor/wheel. The microcontroller integrates the gyroscope data and uses proportional and derivative terms to calculate the motor torque needed to balance the robot vertically.

Uploaded by

MuhammadHaris
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
589 views

Self Balancing Robot

This document describes the design and operation of a self-balancing two-wheeled robot. It contains inertial sensors like a gyroscope and accelerometer to measure tilt. A microcontroller uses these sensor readings along with a balancing algorithm to determine if the motor needs to rotate clockwise or counterclockwise to counteract any tilt via a reaction wheel. The key parts are the inertial sensors, microcontroller, and actuator motor/wheel. The microcontroller integrates the gyroscope data and uses proportional and derivative terms to calculate the motor torque needed to balance the robot vertically.

Uploaded by

MuhammadHaris
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Self Balancing Robot

Two wheeled balancing robot is a classic engineering problem


based on inverted pendulum and is much like trying to balance a
broom on the tip of your finger.
The word balance means the inverted pendulum is in equilibrium
state, which its position is like standing upright 90 degrees.
However, the system itself is not balance, which means it keeps
falling off, away from the vertical axis. Therefore, a gyro chip is
needed to provide the angle position of the inverted pendulum or
robot base and input into the microcontroller, which the program in
itself is a balancing algorithm. The microcontroller will then provide
a type of feedback signal through PWM control to the H-bridge
circuit to turn the motor clockwise or anticlockwise, thus balancing
the robot.
The basic idea for a two-wheeled dynamically balancing robot is
pretty simple: move the actuator in a direction to counter the
direction of fall. In practice this requires two feedback sensors: a tilt
or angle sensor to measure the tilt of the robot with respect to
gravity, an accelerometer to calibrate the gyro thus minimizing the
drift. Two terms are used to balance the robot. These are 1) the tilt
angle and 2) its first derivative, the angle velocity. These two
measurements are summed and fed back to the actuator which
produces the counter torque required to balance the robot.
The robot can be classified into the following parts:
Inertial sensors
Logical processing unit
Actuator

INERTIAL SENSOR UNIT:

The inertial sensors used here are:


GWS Piezo Rate Gyro
Freescale 1-axis accelerometer
A gyroscope, made from a spinning wheel, is the classical method
for achieving a vertical reference. Unfortunately they are large and
clumsy, which is not suitable for Gyros small design. Thanks to
advances in micro-electro-mechanical systems (MEMS), the
gyroscope has been reduced to an incredibly small package. By
measuring this induced vibration you can tell which way it is
rotating and how fast. This is known as a piezoelectric rate
gyroscope and Gyro uses one to help achieve a vertical reference.

LOGICAL PROCESSING UNIT:

The processing unit used is Atmel ATMega16, 8-bit microcontroller


unit which is a versatile EEPROM. It has four I/O ports, onboard
ADC and two PWM outputs. It can be programmed easily with
minimum hardware requirements which make it extremely popular
in robotics applications. Here it performs the following functions:
ADC conversion of outputs of Rate Gyro and Accelerometer
Processing the input signals
Periodic recalibration of gyro
Display of angle & other data.
Control of actuator unit

ALGORITHM
The algorithm for the controller is as follows:
Step1:
Initialize the values of rate gyro bias and accelerometer bias for
zero value of & .
Step2:
Measure the value of voltage of gyro and accelerometer outputs
and store those values as and Ax.
Step3:
Integrate the rate gyro reading by: t = t-1 + *t
Differentiate the rate gyro reading by: t = ( t t-1 )/ t t in
each case is assumed to be constant and is equal to the cycle
time.
Step4:
Calculate the raw angle and gravity angle and compute the error
value.
Step5:
Update the raw angle by:
stabilized = raw angle + K2 (gravity angle - raw angle)
K2 is taken as .2

Step6:
Calculate the torque required to restore:
= K3 * sin
for small angles:
= K3 *
Step7:
Obtain the direction of rotation of the reaction wheel:
If < 0 ; counterclockwise
If > 0 ; clockwise
Step8:
Send the output to the DC motor attached to the reaction wheel.
Step9:
Repeat steps (2-8)

ACTUATOR UNIT

As the robot tilts, we require to apply a restoring force to return the


robot to vertical position.A reaction wheel pendulum model is
followed for the balancing purpose.The components used are:
High torque 12V DC motor
A metallic reaction wheel
1f ,15V capacitor

PARTS REQUIRED:
Wheels
AtMega 16
Rate gyro & accelerometer
DC Gear Motor
Simple DC Motor
9V Battery
Balancing Wheel
Flywheel

You might also like