ProNest

Nesting Software | 2012

Installation and Quick Start Guide

COPYRIGHTS
2012 Hypertherm, Inc. All rights reserved.
Information in this document is subject to change without notice.
The software described in this document is furnished under a license agreement or
nondisclosure agreement. The software may be used or copied only in accordance with
the terms of those agreements. No part of this publication may be reproduced, stored
in a retrieval system, or transmitted in any form or any means electronic or
mechanical, including photocopying and recording for any purpose other than the
purchasers personal use without the written permission of Hypertherm, Inc.
Hypertherm CAM Solutions
22 West Main Street
Lockport, NY 14094
U.S.A.
www.HyperthermCAM.com
TRADEMARKS
Hypertherm and ProNest are trademarks of Hypertherm, Inc. and may be registered in
the United States and/or other countries. Microsoft, Windows, and Internet Explorer are
registered trademarks of Microsoft Corporation in the United States and/or other
countries. Adobe and Adobe Reader are either registered trademarks or trademarks of
Adobe Systems Incorporated in the United States and/or other countries. HASP is a
registered trademark of Aladdin Knowledge Systems Ltd. in the United States and/or
other countries.

Rev-01/12.

ProNest Installation and Quick Start Guide

In this guide
Installation and Setup .......................................................................................... 2
System requirements....................................................................................... 2
Installing ProNest ............................................................................................ 2
Licensing ........................................................................................................ 3
Machine setup files .......................................................................................... 3
ProNest Quick Start Guide ..................................................................................... 4
Opening and closing ProNest ............................................................................ 4
Main ProNest window ....................................................................................... 5
Starting a new job ........................................................................................... 6
Adding parts to your part list ............................................................................ 7
Automatic and interactive nesting ................................................................... 10
Modifying the nest ......................................................................................... 11
Creating clusters of parts ............................................................................... 13
Moving and rotating selected parts .................................................................. 14
Creating a new nest ...................................................................................... 15
Deleting a nest ............................................................................................. 16
Cut simulation .............................................................................................. 17
Saving and opening jobs ................................................................................ 18
Output ......................................................................................................... 19
Reports ........................................................................................................ 19
Contacting Us .................................................................................................... 20
Index ............................................................................................................... 22
This guide performs two functions. The first half is an installation guide, which explains
the installation, licensing and setup of ProNest.
The second half of the guide is called ProNest Quick Start Guide. The purpose of the
quick start guide is to walk you through many of the important tasks in ProNest. By
following the steps presented in this guide, you will get a basic understanding of how to
use ProNest.

ProNest Quick Start Guide

Installation and Setup

System requirements
Software

Windows XP (with Service Pack 3 or later), Windows Vista (SP2 or later), Windows
7 (SP1), or later

Microsoft Internet Explorer 6.0 or later

Microsoft Excel*

Hardware

1 GHz processor or faster (3 GHz recommended)

Vista: 1 GB RAM (2 GB recommended)

XP: 512 MB RAM (1 GB recommended)

VGA display with at least 256 colors and a resolution of 1024 x 768

700 MB available disk space

* Microsoft Excel 2000 or later is recommended for editing ProNest settings

spreadsheets (.xls). If Microsoft Excel is not available, a similar spreadsheet application
can be used.

Installing ProNest
Important:

Do not plug the HASP hardware key (

have installed ProNest.

) into your computer until after you

Before installing ProNest, be sure that you have logged in as the system
administrator. Otherwise, ProNest cannot install properly.

To install ProNest:
1

Close all programs.

Insert the CD labeled ProNest into your CD/DVD drive. If Autorun is enabled on
your system, the installation starts automatically and you can skip steps 3 and 4.

From the Start menu, select Run.

Type D:\setup (substitute the appropriate letter of your CD/DVD drive for D).

Follow the instructions on the screen to complete the installation.

ProNest Quick Start Guide

Licensing
Your copy of ProNest came with a removable HASP hardware key (
). This security
key contains your license information and must be plugged in for ProNest to work.
Important: Be sure to keep your HASP key in a safe place. If lost or stolen, a
replacement fee will be required.

Local license
If you have a local ProNest license (ProNest will be used on only one PC at a time):

After installing ProNest, simply plug the HASP key into your computers USB
port.
ProNest can now be run on your PC, as long as the HASP key remains plugged
in.

Network license
If you have purchased a network license, you will need to designate a computer as the
network license server. The network license server will use your HASP key to manage
the allocation of licenses for all ProNest clients.
Note that the network license server is not required to have ProNest installed on it.

Setting up the network license server

If the network license server will have ProNest installed on it, simply install ProNest and
then plug your HASP key into the USB port of that PC. Your network license will be
ready for use.
If the network license server will not have ProNest installed on it, you should install and
run the stand-alone License Manager utility on that PC.
To install License Manager:
1

Close all programs.

Insert the CD labeled ProNest into the CD/DVD drive of the network license server.

Browse to D:\Utilities (substitute the appropriate letter of your CD/DVD drive for
D).

Double-click LicenseMgrSetup.exe.

Follow the on-screen instructions to complete the installation.

Once installation is complete, plug your HASP key into the USB port of the network
license server. Your network license will be ready for use.

Machine setup files

Once ProNest has been installed, you should confirm that the proper machine setup
files (.pnca) are also installed on your computer. This will ensure that ProNest can
create correct NC code for your specific cutting machine.
If you did not receive a PNCA machine setup, please contact your regional Hypertherm
office to obtain one that matches your machine's hardware configuration.

ProNest Quick Start Guide

ProNest Quick Start Guide

The ProNest Quick Start Guide is designed to familiarize you with ProNest and help you get
started with the application. By following this guide, you will get a good understanding of
the basic functions of ProNest.
This guide will walk you through the following tasks:

Opening, saving, and starting new jobs

Adding parts to your part list

Nesting (interactive and automatic)

Cut simulation

Generating output and reports

Opening and closing ProNest

After you install the program, the ProNest icon is displayed on your desktop.
To open ProNest:
From your desktop, double-click the ProNest icon.
OR
From the Start menu, point to All Programs, then Hypertherm CAM, then
ProNest 2012 Nesting Software, and then click ProNest 2012.
To close ProNest:
Click the Close button (

) in the upper-right corner of the main ProNest window.

OR
On the File menu, select Exit ProNest.

ProNest Quick Start Guide

Main ProNest window

When you launch ProNest, the main window will appear. It is divided into three
sections:

Menus and toolbars

Task panes (Part List, Separations, and Color Legend)

Nesting area

The top section of the main window contains the main menu (File, Edit, View) and
several toolbars. These menus and toolbars will be used throughout this guide to
perform specific tasks. The status bar along the bottom of the main window is also
considered part of the menus and toolbars.
The left-hand side of the main window is occupied by task panes: the Part List,
Separations, and the Color Legend. When ProNest is started normally, the Part List will
not contain any parts.
The remaining area of the main window is devoted to nesting. In the nesting area will
be the image of an empty nest. On startup, ProNest will automatically select a machine
(settings file) and open a new job. The empty nest displayed will have the dimensions
of the machines default plate.
Note: Discussion of ProNest settings is beyond the scope of this guide. For more
information about ProNest settings, consult the ProNest Help, which can be
opened from the Help menu in the main ProNest window.

ProNest Quick Start Guide

Starting a new job

When ProNest is started, a new job is automatically created for you. For the purposes
of this guide, we will discard this job and create a new one.
To create a new job:
1

On the File menu, select New.

The New Job dialog will appear.

Type My first job in the Description box.

Select Demo Plasma Machine from the Use this machine combo box.

Click OK.

Note: When you click OK to create a new job, the Edit Part List window will
automatically appear. Adding parts to your part list will usually be the first step
after creating a new job. For now, close this window.
To close the Edit Part List window:
In the upper-right corner of the window, click Return to Nesting.
Closing the Edit Part List window will cause ProNest to return to the main window.
Notice that the Part List is still empty. The status bar at the bottom of the screen will
indicate the name of the current machine. The machine displayed here contains all the
settings that are used for the current job. The machine displayed in the status bar will
match with the machine you selected in the New Job dialog.
At this point, we are ready to add parts to our part list.

ProNest Quick Start Guide

Adding parts to your part list

This section of the guide will show how to add parts to your part list. Editing of the jobs
part list is done in the Edit Part List window.
To open the Edit Part List window:
On the Job menu, click Edit Part List.
The Edit Part List window will open.
Like the main window, the Edit Part List window has menus and toolbars along the top
and a status bar along the bottom. The rest of the window is split into four sections:

The upper-left contains ProNest part sources. Each part source appears as a
different tab. The CAD tab is a standard part source. Other tabs will also appear
here, depending on which modules you have purchased. This guide will focus only
on using the CAD source.
The lower-left contains the jobs part list. All parts that have been added will appear
here.
The upper-right contains the Preview pane. The currently selected part is displayed
here. If the selected part is from one of the part sources, then this preview is
showing a pre-processed view of the selected part file. If the selected part is in the
part list, then the preview displays the part exactly as it would nest on a plate.
The lower-right contains the Properties pane. Properties for the currently selected
part are displayed here. When the selected part is from one of the part sources, the
part properties reflect the values that will be used to add the part. Changing these
values will affect any subsequent parts that are added to the part list. If the selected
part is from the part list, however, the properties reflect the actual properties of the
part. Changing these values directly affects the selected part.

Sample CAD files

During installation of ProNest, sample CAD (.dxf) files were placed in one of the
following locations, based on the version of Microsoft Windows that is installed on your
PC.
Windows Vista or 7:
C:\ProgramData\Hypertherm CAM\ProNest 2012\Examples
Windows XP:
C:\Documents and Settings\All Users\Application Data\Hypertherm
CAM\ProNest 2012\Examples
This guide will use these files to help showcase the features of ProNest. Feel free to use
these files as you learn ProNest.

To select a CAD part:

1

Select the CAD tab in the Part Sources section.

ProNest Quick Start Guide

The CAD tab works like Windows Explorer, allowing you to browse the folders and
files on your system. Use the Look in box to help navigate. By default, the Files of
type box will be set to AutoCAD files (*.dwg;*.dxf). The selection in this box will
filter the contents of the current folder, only showing the files that match.
2

In the CAD tab, make sure that the Examples folder is currently selected.

Find and click MF2.DXF once to select it.

When selected, the name of the part will appear highlighted. The Preview tool window
will display the selected CAD file and the Properties tool window will display the
properties that will be used to add the part.
Important: The CAD files installed into the Examples folder were drawn using specific
layer names. Each layer name defines a different attribute such as
profiles for cutting, scribing, punching, or dimension information. Using
the properties for a selected CAD part, you can match each CAD layer
with a machine process. Using layers in this way allows ProNest to
distinguish between the different aspects of a drawing when the part is
added. When adding parts, assigning layers to the proper machine
processes is critical to correct output.

To modify CAD Layer information prior to adding a part:

1

With MF2.DXF selected, click on the CAD Import tab in the Properties tool
window.
In the CAD Layers section, the following process-layer mappings will already exist:
Process
Cut - [Plasma]
Scribe - [Scribe-P]

CAD Layer
0;CUT
SCRIBE

Also notice that the preview color used for each process is displayed to the left of
the process name.
2

Click on the word SCRIBE in the right column and then click the down-arrow.

This will display a list of the CAD layers found in the selected part and in the
machine settings for Scribe-P. In the illustration above, the layers found for
MF2.DXF are 0, CUT, PUNCH, and SCRIBE. Notice that each of these layer names

ProNest Quick Start Guide

has a small image of a part next to it ( ). This image indicates that the layer was
found in the part. Other layer names may appear simply because they have been
assigned to the process as a default layer mapping. Default layer mappings are
defined in your machine settings. In the illustration above, the SCRIBE, 2, and Mark
layers have been specified in the default layer mapping setting for Scribe-P. These
layer names have a small settings image next to it ( ). When MF2.DXF is first
selected, SCRIBE is the only layer mapped to the Scribe-P process because it is the
only layer name that is found both in the part and in the machine settings for
Scribe-P.
3

Clear the SCRIBE check box (but do not click OK or Cancel).

Notice that as you clear the SCRIBE check box, the blue scribe lines in the preview
disappear. This means that if you were to click OK and then add the part, the
information on the parts SCRIBE layer would not be imported into ProNest. By not
mapping a layer name to a process, you are instructing ProNest to ignore the
contents of that layer. Also notice that you cannot select 2 or Mark because neither
layer was found in the part.

Select the SCRIBE check box and click OK.

Prior to adding a part to the part list, it is common to edit the property values in the
Nesting and CAD Import tabs. Typically, you will need to change the quantity and
material for the part (although these can be changed after the part is added).
To add MF2.DXF to the part list (be sure that MF2.DXF is selected):
1

In the Properties tool window, select the Nesting tab.

Change the value for Required to 5.

In the Standard toolbar at the top of the window, click Add Part.
MF2.DXF will be added to the Part List in the lower-left.

To add BLADE.DXF to the part list:

1

In the CAD tab, select BLADE.DXF.

In the Properties tool window, select the Nesting tab.

Change the value for Required to 12.

On the Edit menu, click Add Part.

BLADE.DXF will be added to the Part List in the lower-left.

Tip: There are several ways to add parts from the CAD source.
In addition to using the menu and toolbars, you can:
Double-click a part
Drag a part from the CAD source down into the Part List.
Similar to Windows Explorer, you can select multiple part files and add them.
To select a range of parts, select the first part and then hold SHIFT as you
select the last part in the range. You can also hold CTRL as you individually
select multiple parts in the list.
Now that you have a simple part list developed, return to the main window.
To close the Edit Part List window:
In the upper-right corner of the window, click Return to Nesting.

ProNest Quick Start Guide

Automatic and interactive nesting

At this point you have learned how to start a new job and then how to add parts to
your part list. With a couple of parts in the Part List and an empty nest in the nesting
area, you are now ready for nesting.
Parts can be nested in two different ways:

Interactive nesting: Parts are added one at a time from the Part List. Nested parts
are positioned manually by moving and rotating them.
Automatic nesting: ProNest calculates the position of all parts in the Part List and
nests them. Usually, all quantities in the part list will be nested when automatic
nesting is complete.

To interactively add parts to the nest:

Drag a part from the Part List onto the nest.
OR
Double-click a part in the Part List.
To automatically add parts to the nest:
Click the green

Start AutoNest button in the Nest toolbar.

OR
Click the yellow

Start AutoNest button in the Nest toolbar.

Note: The Start AutoNest button: Yellow vs. Green

The yellow AutoNest button is slightly different from the green button.
The yellow button opens the AutoNest Setup dialog. Using this dialog, you can
make last-minute changes to things like:
The selected nesting strategy
Where automatic nesting should begin (first, current, or new nest)
The types and sizes of plates to use
When the settings in the AutoNest Setup dialog are ready, click OK to begin
automatic nesting.
The green button will simply go ahead and begin automatic nesting using the last
settings specified in the AutoNest Setup dialog. In effect, clicking the green
button is equivalent to opening the AutoNest Setup dialog and clicking OK.

10

ProNest Quick Start Guide

Modifying the nest

Once you have added parts to the nest, you are free to modify the nest in any way. You
can delete parts from the nest, add more parts, rotate and move parts around, and
perform more advanced functions such as clustering. This section of the guide will
showcase several ways of working with parts on a nest.

Selecting parts
Nested parts cannot be moved or rotated until they are selected.
To select a single part:
Click anywhere inside the part.
To select all parts on the nest:
On the Edit menu, click Select All.
To select multiple parts:
Hold SHIFT as you select each part.
To area-select multiple parts:
Right-click and drag a rectangular area to surround the parts that should be
selected. As you drag, the selection area will be drawn as a box with dotted lines.
Tip: The direction of an area-select drag changes how parts are selected. If the
selection area is created by dragging to the right, then parts will be selected only
if they are fully contained by the selection area. If the selection area is created by
dragging to the left, then parts will be selected if they are fully contained by
selection area or if they come in contact with the border of the selection area.
When a part (or group of parts) is selected, it will turn blue and will be surrounded by a
selection box.

The selection box surrounds the entire selection and features bump and rotate handles.
These handles provide specialized ways to move and rotate the selection. See the
section called Moving and rotating selected parts for more information about using
the selection box handles.

Unselecting parts
When parts are selected, they are not truly nested. It is more correct to think of
selected parts as a floating group of parts. To nest a selection, unselect it.
To unselect all parts:
Click anywhere in the nesting area that is not inside any part.
OR
On the Edit menu, click Unselect All.

11

ProNest Quick Start Guide

To remove a single part from the selection:
Hold SHIFT and select the part you want to unselect.
All other parts in the selection will remain selected.
Note: As you select and unselect nested parts, you may have noticed changes in the
Part List. Sometimes the reported nested quantity appears like this:
2 of 5 nested [1]
This means that 2 out of 5 parts are nested and that 1 part is selected. If the
selected part were then unselected, the quantities would appear like this:
3 of 5 nested

Removing a part from the nest

A nested part can be removed from the nest, returning it to the part list. This causes
the parts available quantity to rise as its nested quantity decreases.
To remove a selected part from the nest:
Press DELETE.
OR
Drag the part from the nesting area into the Part List tool window.
OR
On the Edit menu, click Delete.

12

ProNest Quick Start Guide

Creating clusters of parts

Two or more parts can be grouped together into a cluster. A cluster maintains the
orientation of its parts with respect to each other while allowing you to work with the
cluster as if it were a single part. This is typically used when parts are arranged in a
way that is generally useful. Clustering a group of parts makes the cluster available in
the part list as a Custom Part. The custom part can then be used as if it were a
regular part.
To create a cluster:
1

Select two adjacent parts on the nest.

On the Part menu, click Cluster.

If this is your first cluster, then the Part List tool window should now contain a part
called Custom Part 1. The thumbnail image for this part will show that the part is
made from the two parts currently selected on the nest.

Note: Notice that the two selected (and clustered) parts on the nest act as if they are a
single part. If you unselect them and then click on either part they both become
selected. If you drag one of the parts, they both move together. Clustered parts
will act like a single part until they are unclustered.
To uncluster parts:
1

Select parts on the nest that are clustered.

On the Part menu, click Uncluster.

The parts are now independent from each other. One part can be selected without
the other becoming selected. This does not, however, remove the cluster from the
part list (the part called Custom Part 1).

13

ProNest Quick Start Guide

Moving and rotating selected parts

Once parts are selected, they can be moved and rotated into any position.
To move a selected part:
Drag a part from one location on the nest to another.

Using the bump handles

Parts can be moved in a variety of ways using the bump handles. Bump handles ( )
are located on the sides of the selection box. As you point to each bump handle, the
pointer will change to an arrow indicating the bump direction.

Normal bump: Click a bump handle. This moves a part until it comes in contact
with either another part or the plate edge and will leave the part a normal
separation distance from other parts or from the plate edge.
Nudge: While holding SHIFT, click a bump handle. The part will move a small
distance in the specified direction. The distance is defined on the Nesting page of
your settings.
Zero separation bump: While holding CTRL, click a bump handle. This works
similarly to normal bump except that it will leave the part in contact with the other
part or with the plate edge (with no separation). This is useful if you intend to cut
common lines

Tip: You can also use the arrow keys to bump parts. Pressing the UP ARROW key, for
example, acts just like clicking the top bump handle. Like the bump handles, the
arrow keys can be combined with SHIFT and CTRL to perform nudges and zero
separation bumps.

Using the rotate handles

Rotate handles ( ) are located in the corners of the selection box. As you point to
each of these handles, the pointer will change to indicate a specific rotate function.

Free rotate (upper-right): Drag this handle to rotate the part freely.
Incremental rotate (upper-left): Click this handle to rotate the part counterclockwise by a fixed amount (defined on the Nesting page of your settings).
Rotate to next 90 (lower-left): Click this handle to rotate the part counterclockwise to the next 90 rotation. 90 rotations are all based on the parts neutral
orientation (not its current rotation).
Rotate long side (lower-right): Click this handle to rotate the part counterclockwise to the next 90 rotation for the parts longest side. A right-triangle part
would rotate to positions that place its hypotenuse at 90, 180, 270, and 360
orientations.

14

ProNest Quick Start Guide

Creating a new nest

With ProNest you can manage exactly which nests are used. If you dont like a
particular nest, you can delete it. If you need another nest, you can create one and
begin nesting on it.
To create a new nest:
1

On the Nest menu, click New Nest.

The New Nest Setup dialog will appear.

At this point, a custom rectangular plate will already be selected. To specify the
dimension of your new plate, you can either type values in the Length and Width
boxes or you can select a standard plate size from the box directly above Length.
2

Type 150 in the Length box.

Type 50 in the Width box.

Notice that the preview updates as you change the plate dimensions.

Click OK.
ProNest will create the new nest and make it current. You should now see your new
(and empty) nest in the main window.

15

ProNest Quick Start Guide

Deleting a nest
Deleting a nest will place all of its parts back in the part list, adjusting their quantities
appropriately.
To delete the current nest:
On the Nest menu, select Delete Nest.
To delete all nests in the job:
On the Nest menu, select Delete All Nests.
Note: ProNest always has a current nest even if you delete all nests or if you delete
the only nest in the job. If you delete the last remaining nest in the job (referred
to as Nest 1 of 1), the end result will be similar to selecting all the parts on this
nest and then deleting them. Similarly, if you delete all nests, the end result will
be similar to deleting every nest past the first nest and then clearing the first
nest.

16

ProNest Quick Start Guide

Cut simulation
Before generating output, it is often convenient to see how a nest will be cut. Cut
simulation presents an animation that approximates how a nest would be cut by your
machine. ProNest allows simple control over the simulation, similar to playing a movie.
To view cut simulation for the current nest:
On the Nest menu, select Cut Simulation.
When you enter cut simulation, the parts on the nest will be drawn in the Uncut
color from the Color Legend tool window. Also, the Cut Simulation toolbar will
appear.

To play the simulation:

On the Cut Simulation toolbar, click the Play button.
When cut simulation starts, a small image of a cutting head will appear at the
initialization point of the nest. The cutting head will then move around the nest,
cutting, scribing, and punching the nest in the same order as CNC output would
instruct the machine.
To pause the simulation:
On the Cut Simulation toolbar, click the Pause button.
To stop the simulation:
On the Cut Simulation toolbar, click the Stop button.
To quit cut simulation and return to normal nesting:
On the Cut Simulation toolbar, click Close.
Tips:
The speed of the cut simulation can be controlled by moving the Speed slider.
Move the slider to the left for a slower simulation. Move the slider to the right for
a faster simulation.
You can skip ahead (or back) by clicking on any profile in the nest.

17

ProNest Quick Start Guide

Saving and opening jobs

Often you will want to save your work so you can return to it at a later time. The exact
state of your job (including your settings) can be saved in a job file. ProNest jobs have
an .nif file extension.
To save a job:
1

On the File menu, click Save As.

The Save As dialog will appear.

Browse to the appropriate folder for your job.

In the File name box, type the name for your job file.

Click Save.
The current job will be saved with the name you specified.

To open a job:
1

On the File menu, click Open.

The Open dialog will appear. Use this dialog to browse to the folder containing the
job you want to open.

Select the job file you want to open.

Click Open.

Tip: On the right-hand side of the Open dialog is a box containing job information.
Displayed in this box is the jobs description (if any), the machine settings that
were saved in it, date created, date modified, and the version of ProNest last used
to save the job.
When a job is opened, ProNest will first load a fresh copy of settings from the
machine shown in the job information box. Then, as it opens the job, it may or
may not restore the settings that were saved in it.
Below the job information box is a check box called Restore settings from job.
Select this check box to restore the settings that were saved in the job. This tells
ProNest to completely restore settings to what they were when the job was saved.
Clear this check box to open the job and use the machine settings as they are.
This is typically done when you have edited your machine settings and want to reoutput a job using those new settings.

18

ProNest Quick Start Guide

Output
Ultimately, the purpose of any ProNest job is to create correct output for your machine
controller. When a job is ready for this step, CNC output can be created.
To create CNC output for the current job:
1

On the File menu, select Output CNC.

The CNC Output dialog will open. Use this dialog to select the file name for the
output file.

In the File name box, type a name for your output file.
ProNest will assign a unique file name to each nest in your job, based on the file
name that you entered.

Click Output.
ProNest will create a CNC file for each nest in your job. These CNC files would then
be sent to your machine controller.

Important: ProNest is typically not ready to produce valid output code immediately
after installation. The proper machine setup files (PNCA) must be installed
before correct NC output can be created. For help with setup issues,
contact Technical Support.

Reports
At any time you can view and print reports for your current job. There are several
standard reports to choose from in the Reports dialog.
To open the Reports dialog:
On the File menu, click Reports.
The Reports dialog will open, showing a list of reports that are available.
To preview a particular report:
1

Select the check box for the report you want to preview.

Click Preview.

19

ProNest Installation and Quick Start Guide

Contacting Us
Address:

Hypertherm CAM Solutions

22 West Main Street
Lockport, NY 14094
U.S.A.

Telephone:

+1 (716) 434-3755

Fax:

+1 (716) 434-3711

World Wide Web:

www.hyperthermCAM.com

Email:

[email protected]

Office hours:

Monday to Friday
8:00 A.M. to 5:00 P.M. Eastern Time

Technical Support
Hypertherm CAM Solutions is committed to providing you with the best overall product
experience. This includes intuitive technical products and flexible options to fit your
support needs. Our products are designed with superior quality and ease of use in
mind, but we understand that issues do arise from time to time that need the backing
of our support resources.
For current hours of operation, details about all support offerings, and a knowledge
base, please visit our website:
www.hyperthermCAM.com/support

Sales
Contact your account representative for information about the latest
Hypertherm products, the Software Subscription program, upgrade options and prices,
and more. If you have a technical question or problem, please contact Technical
Support.

20

ProNest Installation and Quick Start Guide

Locations
America

Asia

Hypertherm CAM Solutions

22 West Main Street
Lockport, NY 14094 USA
+1 (716) 434-3755 Tel
+1 (716) 434-3711 Fax
[email protected]

Hypertherm (Shanghai) Trading Co.,

Ltd.
Unit A, 5th Floor, Careri Building
432 West Huai Hai Road
Shanghai 200052, PR China
86-21 5258 3330 /1 Tel
86-21 5258 3332 Fax
[email protected]
Hypertherm (S) Pte Ltd.
82 Genting Lane
Media Centre Annexe Block #A01-01
Singapore 349567
+65 6841 2489 Tel
+65 6841 2490 Fax
[email protected]

Europe
Hypertherm Europe B.V.
Vaartveld 9
4704 SE
Roosendaal
The Netherlands
+31 (0) 165 596907 Tel
+31 (0) 165 5969801 Fax
[email protected]

Hypertherm Japan Ltd.

801 Samty Will Building
2-40 MNiyahara 1-Chrom
Yodogawa-ku
Osaka, 532-0003, Japan
+81 (6) 6225 1183 Tel
+81 (6) 6225 1184 Fax
[email protected]

Latin America
Hypertherm Mxico, S.A de C.V.
Av. Toluca No. 444, Anexo 1
Col. Olivar de los Padres
Del. lvaro Obregn
D.F. C.P. 01780, Mexico
+52 55 5681 8109 Tel
+52 55 5683 2127 Fax
[email protected]

Hypertherm Korea Branch

#3904 Centum Leaders Mark B/D
1514 Woo-Dong
Haeundae Gu
Busan, Korea 612-889
+82-51-747-0358 Tel
+82-51-701-0358 Fax
[email protected]

Hypertherm Brasil Ltda.

Rua Brs Cubas
231 Jardim Maia
CEP 07115-030
Guarulhos, SP - Brasil
+55 11 2409 2636 Tel
+55 11 2408 0462 Fax
[email protected]

Hypertherm (India) Thermal

Cutting Pvt. Ltd.
New No. 83, Old No. 52
Bazullah Road, T. Nagar
Chennai, Tamil Nadu
India 600 017
South/East: +91 99 4068 1650 Tel
North/West: +91 99 5844 4984 Tel
+91 (0) 44 2834 5362 Fax
[email protected]

21

ProNest Installation and Quick Start Guide

Index
L

A
Licensing
local, 3
network, 3

Adding parts. See Part List

Automatic nesting, 10
AutoNest Setup dialog, 10

Manual nesting. See Interactive nesting

Modifying the nest, 11

Bump, 14
Bump handles, 11, 14

C
Nest
creating new, 15
deleting, 16
modifying, 11
Nesting
automatic, 10
interactive, 10
New Job dialog, 6
New Nest Setup dialog, 15
Nudge, 14

CAD files
adding to the part list, 9
browsing for, 8
layer information, 8
sample files, 7
selecting, 7
CAD Import
layer information, 8
properties, 9
Closing ProNest, 4
Clusters, 13
CNC Output, 19
Contacting Hypertherm CAM Solutions, 20
Sales, 20
Technical Support, 20
Cut simulation, 17

O
Opening ProNest, 4
Output. See CNC Output

Part List
adding parts, 79
toolbar, 6
Parts
area select, 11
cluster, 13
removing, 12
selecting, 11
unselecting, 11
ProNest
closing, 4
installing, 2
opening, 4
user manual, location of, 5
ProNest Job
information, 18
opening, 18
restore settings from, 18
saving, 18
starting new, 6
ProNest Licensing, 3
ProNest main window, 5

Deleting parts, 12

E
Edit Part List window
closing, 9
layout, 7
opening, 7

H
Hypertherm CAM Solutions
contacting, 20
Sales, 20
Technical Support, 20

I
Installing ProNest, 2
Interactive nesting, 10

Job. See ProNest Job

Removing parts, 12

22

ProNest Installation and Quick Start Guide

Simulation. See Cut simulation
Start AutoNest button, 10
yellow vs. green, 10
System requirements, 2

Reports, 19
Restore settings from job, 18
Rotate
free, 14
incremental, 14
long side, 14
to next 90, 14
Rotate handles, 11, 14

T
Technical Support, 20

Selecting parts, 11
Selection box, 11

Unselecting parts, 11

23

Hypertherm and ProNest are trademarks of Hypertherm, Inc.

and may be registered in the UnitedStates and/orother countries.
For more information, contact your authorized Hypertherm dealer
or visit www.hyperthermCAM.com.
2012 Hypertherm, Inc. All rights reserved.
PNGDE-0001-NA