Scribd
Upload
46K views

Notes To Study For Physics Paper 6

The document provides guidance on preparing for a physics exam, including summarizing the key topics to study: general physics, thermal physics, waves, magnetism, and atomic physics. It also lists important safety precautions to follow when conducting physics experiments in the laboratory, such as not touching live wires, using gloves and safety equipment, and preventing mercury spills. Finally, it outlines several variables, measurements, sources of error, and improvements that students should consider for experimental physics questions on the exam.

Uploaded by

sakibsultan_308
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
46K views

Notes To Study For Physics Paper 6

The document provides guidance on preparing for a physics exam, including summarizing the key topics to study: general physics, thermal physics, waves, magnetism, and atomic physics. It also lists important safety precautions to follow when conducting physics experiments in the laboratory, such as not touching live wires, using gloves and safety equipment, and preventing mercury spills. Finally, it outlines several variables, measurements, sources of error, and improvements that students should consider for experimental physics questions on the exam.

Uploaded by

sakibsultan_308
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 13

Physics (Alternative to Practical) 62 Tuesday

Just study all 5 Topics of physics:

General Physics
Thermal Physics
Waves
Magnetism
Atomic Physics

And you'll do fine For paper 6 learn all the 5 topics


experiments precautions.

Physics laboratory safety precautions / rules:

* Live wires should not be touched.

* Hot Objects should not be touched with barren hands instead


of that gloves should be used the most common process is
heating of water in thermodynamic experiments.

* Circuit connections should be checked and approved by the


teacher and then only the circuit should be switched ON.

* While changing components of the circuit the power should


be switched so that one should not experience electric shocks.

* Safety spectacles, gloves and other safety components should


be used while handling experiments.

* While handling a mercury thermometer one should take of


the mercury spills.

* No other laboratory instruments should be touched or


handled which is not involved in the course of experiments.

micrometer : can measure the thickness of any small thing to


0.01 mm
vernier : can measure the inner and outer wall of anything to
1.05mm
Control Variables
Precautions
Units ( eg.. voltage is V etc. ) cause the units hold 1 mark of the
question
Statements & justification
The rest are calculations and measurements
To produce more accurate or reliable results:

Repeat experiment, to calculate average reading.

Avoiding parallax error, look perpendicular to the ruler.


If accuracy in measurement was asked, check for zero
error.
Improvements that could be done to the experiment (temp.
cooling):

Same initial temperature.

Same volume of water.

Same shape of beaker.

Beakers of same surface.

Same room temperature.

Stirring the water in the beakers.

Same time intervals.

Same surface area. (Unless given different containers)

Adding water or cooling effect at regular intervals.

Heat loss could be reduced by:

Insulation of beaker.

Covering beaker with a lid.

For 2 values to be directly proportional,

The graph of the values must be a straight line from the


origin.

As value 1 increase, value 2 increases.

For images produced from lenses on screens, precautions


taken:

Use of a darkened room for the experiment.

Avoiding parallax error in measurement, and look


perpendicular to the ruler.

Object and lens at the same height from bench.

Object/lens/screen is perpendicular to the bench.

To draw an image created from lens:

Inverted from the original object.

Sides are multiplied by the magnification.

*If values have difference by 0.1 or 0.01, that is the limit of


experimental accuracy, so answers are about the same.
For spring extension experiment, variables that should be
constant in the experiment:

Number of coils.

Diameter of spring.

Selection of loads.

Mass of spring.

http://www.opampelectronics.com/tutorials/experiments_ch_003.htm

micrometer : can measure the thickness of any small thing to


0.01 mm
vernier : can measure the inner and outer wall of anything to
1.05mm
Control Variables
Precautions
Units ( eg.. voltage is V etc. ) cause the units hold 1 mark of the
question
Statements & justification
The rest are calculations and measurements
To produce more accurate or reliable results:
Repeat experiment, to calculate average reading.
Avoiding parallax error, look perpendicular to the ruler.
If accuracy in measurement was asked, check for zero error.
Improvements that could be done to the experiment (temp.
cooling):

Same initial temperature.


Same volume of water.
Same shape of beaker.
Beakers of same surface.

Same room temperature.


Stirring the water in the beakers.
Same time intervals.
Same surface area. (Unless given different containers)
Adding water or cooling effect at regular intervals.
Heat loss could be reduced by:
Insulation of beaker.
Covering beaker with a lid.
For 2 values to be directly proportional,
The graph of the values must be a straight line from the
origin.
As value 1 increase, value 2 increases.
For images produced from lenses on screens, precautions
taken:

Use of a darkened room for the experiment.


Avoiding parallax error in measurement, and look
perpendicular to the ruler.
Object and lens at the same height from bench.
Object/lens/screen is perpendicular to the bench.
To draw an image created from lens:
Inverted from the original object.
Sides are multiplied by the magnification.
*If values have difference by 0.1 or 0.01, that is the limit of
experimental accuracy, so answers are about the same.
For spring extension experiment, variables that should be
constant in the experiment:
Number of coils.
Diameter of spring.
Selection of loads.
Mass of spring.
for improving the accuracy of the results (for experiments):
Minimizing heating effect of a current:
Lower current

Increase voltage
Add a lamp
Increase resistance of a resistor
To increase accuracy of ray diagrams
View bases of pins since pins may not be vertical
Keep pins further apart
Use more pins
Avoid parallax, explain action and reason
Repeats and average
Adjustments made to experiments will be made to increase
accuracy
Improvement made to experiments about heating effect and
insulation
Lids
Repeats
Stirring
Record max. Temperature
Add insulation
Keep constant room temperature

Avoid heat loss


How to check if a rule is vertical:
Protractor
Use of set square
Plumb line
Spirit Level
Precautions taken in experiments about formation of images by
a lens
Use a darkened area
Meter ruler on bench or clamped
Object and lens same height on bench
Mark on lens holder to show center of lens
Take more readings
Avoid parallax error, explain action and reason
Lens\screen perpendicular to bench
Variables in experiments about springs and stretching effect:
Number of coils
Length of spring
Diameter\thickness of spring or wire

Range of loads
Length of wire
Coil spring
Periodic time (T) is measured by timing a number (n) of
oscillations, then divide the time taken for all the oscillations by
the number of oscillations (n)

Drawing graphs:
Label axis
Choose a proper scale
Well judged best fit line
Thin and neat lines
Measuring the gradient:
Draw a triangle on graph
Use clear lines
Triangle must be larger than half the line
Sources of error in calculating circumference by string method:
Parallax

Diagonal winding
Thickness of string
Improvement made to calculating circumference by string
method
Avoid parallax error
Repeats and average
Thinner string
Parallel winding of springs
It's not the BEST list in the world, but hopefully it will help...
Control Variables
Precautions
Units ( eg.. voltage is V etc. ) cause the units hold 1 mark of the
question
Statements & justification
The rest are calculations and measurements which are easy..
they provide the equation in the question

Paper 6 is one of the easiest


Just memorise the variables.. precautions.. & units
Other then that .. use a sharp pencil when drawing graphs
cause you may lose marks for the thickness of the lines
Be so accurate in measuring angles..

You might also like