www.5starnotes.

com
3003

10122MEE17 UNCONVENTIONAL MACHINING PROCESSES L T P C

co

OBJECTIVE:

UNIT I INTRODUCTION

s.

To learn about various unconventional machining processes, the various process parameters
and their influence on performance and their applications
5

Unconventional machining Process Need classification Brief overview .

te

UNIT II MECHANICAL ENERGY BASED PROCESSES

10

no

Abrasive Jet Machining Water Jet Machining Abrasive Water Jet Machining Ultrasonic
Machining. (AJM, WJM, AWJM and USM). Working Principles equipment used Process
parameters MRR-Variation in techniques used Applications.
UNIT III ELECTRICAL ENERGY BASED PROCESSES

ar

Electric Discharge Machining (EDM)- working Principle-equipments-Process ParametersSurface Finish and MRR- electrode / Tool Power and control Circuits-Tool Wear
Dielectric
Flushing Wire cut EDM Applications.

ww
w.
5s
t

UNIT IV
CHEMICAL AND ELECTRO-CHEMICAL ENERGY BASED PROCESSES

12

Chemical machining and Electro-Chemical machining (CHM and ECM)-Etchantsmaskanttechniques of applying maskants-Process Parameters Surface finish and MRRApplications. Principles of ECM-equipments-Surface Roughness and MRR-Electrical circuitProcess Parameters-ECG and ECH - Applications.
UNIT V THERMAL ENERGY BASED PROCESSES

10

Laser Beam machining and drilling (LBM), plasma arc machining (PAM) and Electron Beam
Machining (EBM). Principles Equipment Types - Beam control techniques
Applications.

Total: 45

-1-

www.5starnotes.com

www.5starnotes.com
UNIT I

co

Introduction

Unconventional Manufacturing Processes

unconventional manufacturing processes is defined as a group of processes that remove

s.

excess material by various techniques involving mechanical, thermal, electrical or chemical

energy or combinations of these energies but do not use a sharp cutting tools as it needs to be
used for traditional manufacturing processes.

te

Extremely hard and brittle materials are difficult to machine by traditional machining

processes such as turning, drilling, shaping and milling. Non traditional machining processes,
also called advanced manufacturing processes, are employed where traditional machining

no

processes are not feasible, satisfactory or economical due to special reasons as outlined
below.

Very hard fragile materials difficult to clamp for traditional machining

When the workpiece is too flexible or slender

When the shape of the part is too complex

ww
w.
5s
t

ar

Several types of non-traditional machining processes have been developed to meet extra
required machining conditions. When these processes are employed properly, they offer
many advantages over non-traditional machining processes. The common non-traditional
machining processes are described in this section.

UNIT II

Electrical Discharge Machining (EDM)

Electrical discharge machining (EDM) is one of the most widely used non-traditional
machining processes. The main attraction of EDM over traditional machining processes such
as metal cutting using different tools and grinding is that this technique utilises thermoelectric
process to erode undesired materials from the workpiece by a series of discrete electrical
sparks between the workpiece and the electrode. A picture of EDM machine in operation is
shown in Figure 1.

-2-

www.5starnotes.com

te

Figure 1: Electrical discharge machine

s.

co

www.5starnotes.com

The traditional machining processes rely on harder tool or abrasive material to remove the
softer material whereas non-traditional machining processes such as EDM uses electrical

no

spark or thermal energy to erode unwanted material in order to create desired shape. So,
the hardness of the material is no longer a dominating factor for EDM process. A
schematic of an EDM process is shown in Figure 2, where the tool and the workpiece are

ww
w.
5s
t

ar

immersed in a dielectric fluid.

Figure 2: Schematic of EDM process

EDM removes material by discharging an electrical current, normally stored in a capacitor
bank, across a small gap between the tool (cathode) and the workpiece (anode) typically in
the order of 50 volts/10amps.
-3-

www.5starnotes.com

www.5starnotes.com
The EDM process has the ability to machine hard, difficult-to-machine materials. Parts with

Application of EDM

co

complex, precise and irregular shapes for forging, press tools, extrusion dies, difficult internal
shapes for aerospace and medical applications can be made by EDM process. Some of the

ar

no

te

s.

shapes made by EDM process are shown in Figure 3.

ww
w.
5s
t

Figure 3: Difficult internal parts made by EDM process

Working principle of EDM

As shown in Figure 1, at the beginning of EDM operation, a high voltage is applied across
the narrow gap between the electrode and the workpiece. This high voltage induces an
electric field in the insulating dielectric that is present in narrow gap between electrode and
workpiece. This cause conducting particles suspended in the dielectric to concentrate at the
points of strongest electrical field. When the potential difference between the electrode and
the workpiece is sufficiently high, the dielectric breaks down and a transient spark discharges
through the dielectric fluid, removing small amount of material from the workpiece surface.
The volume of the material removed per spark discharge is typically in the range of 10-6 to
10-6 mm3.

The material removal rate, MRR, in EDM is calculated by the following foumula:
MRR = 40 I / Tm 1.23

(cm3/min)

Where, I is the current amp,

Tm is the melting temperature of workpiece in 0C

-4-

www.5starnotes.com

www.5starnotes.com
Advantages of EDM

The main advantages of DM are:

By this process, materials of any hardness can be machined;

No burrs are left in machined surface;

One of the main advantages of this process is that thin and fragile/brittle components

co

s.

can be machined without distortion;

Complex internal shapes can be machined

te

Limitations of EDM
The main limitations of this process are:

This process can only be employed in electrically conductive materials;

Material removal rate is low and the process overall is slow compared to conventional

no

machining processes;

Unwanted erosion and over cutting of material can occur;

Rough surface finish when at high rates of material removal.

ww
w.
5s
t

Dielectric fluids

ar

Dielectric fluids used in EDM process are hydrocarbon oils, kerosene and deionised water.
The functions of the dielectric fluid are to:

Act as an insulator between the tool and the workpiece.

Act as coolant.

Act as a flushing medium for the removal of the chips.

The electrodes for EDM process usually are made of graphite, brass, copper and coppertungsten alloys.

Design considerations for EDM process are as follows:

Deep slots and narrow openings should be avoided.

The surface smoothness value should not be specified too fine.

Rough cut should be done by other machining process. Only finishing operation
should be done in this process as MRR for this process is low.
-5-

www.5starnotes.com

Wire EDM

co

EDM, primarily, exists commercially in the form of die-sinking machines and wire-cutting

www.5starnotes.com

machines (Wire EDM). The concept of wire EDM is shown in Figure 4. In this process, a
slowly moving wire travels along a prescribed path and removes material from the

s.

workpiece. Wire EDM uses electro-thermal mechanisms to cut electrically conductive

materials. The material is removed by a series of discrete discharges between the wire

electrode and the workpiece in the presence of dieelectirc fluid, which creates a path for each

te

discharge as the fluid becomes ionized in the gap. The area where discharge takes place is
heated to extremely high temperature, so that the surface is melted and removed. The

no

removed particles are flushed away by the flowing dielectric fluids.

The wire EDM process can cut intricate components for the electric and aerospace industries.
This non-traditional machining process is widely used to pattern tool steel for die

ww
w.
5s
t

ar

manufacturing.

Figure 4: Wire erosion of an extrusion die

-6-

www.5starnotes.com

The wires for wire EDM is made of brass, copper, tungsten, molybdenum. Zinc or brass

co

coated wires are also used extensively in this process. The wire used in this process should

www.5starnotes.com

posses high tensile strength and good electrical conductivity. Wire EDM can also employ to

cut cylindrical objects with high precision. The sparked eroded extrusion dies are presented in

ar

no

te

s.

Figure 5.

ww
w.
5s
t

Figure 5: Sparked eroded extrusion dies

This process is usually used in conjunction with CNC and will only work when a part is to be
cut completely through. The melting temperature of the parts to be machined is an important
parameter for this process rather than strength or hardness. The surface quality and MRR of
the machined surface by wire EDM will depend on different machining parameters such as
applied peak current, and wire materials.

-7-

www.5starnotes.com

www.5starnotes.com
UNIT III

Chemical Machining (CM)

co

Introduction

Chemical machining (CM) is the controlled dissolution of workpiece material (etching) by

s.

means of a strong chemical reagent (etchant). In CM material is removed from selected areas
of workpiece by immersing it in a chemical reagents or etchants; such as acids and alkaline
solutions. Material is removed by microscopic electrochemical cell action, as occurs in

te

corrosion or chemical dissolution of a metal. This controlled chemical dissolution will

simultaneously etch all exposed surfaces even though the penetration rates of the material
removal may be only 0.00250.1 mm/min. The basic process takes many forms: chemical

no

milling of pockets, contours, overall metal removal, chemical blanking for etching through
thin sheets; photochemical machining (pcm) for etching by using of photosensitive resists in
microelectronics; chemical or electrochemical polishing where weak chemical reagents are

ar

used (sometimes with remote electric assist) for polishing or deburring and chemical jet
machining where a single chemically active jet is used. A schematic of chemical machining

ww
w.
5s
t

process is shown in Figure 6.

Figure 6: (a) Schematic of chemical machining process (b) Stages in producing a profiled
cavity by chemical machining (Kalpakjain & Schmid)

Chemical milling

In chemical milling, shallow cavities are produced on plates, sheets, forgings and extrusions.
The two key materials used in chemical milling process are etchant and maskant. Etchants are
acid or alkaline solutions maintained within controlled ranges of chemical composition and

-8-

www.5starnotes.com

www.5starnotes.com
temperature. Maskants are specially designed elastomeric products that are hand strippable

co

and chemically resistant to the harsh etchants.

Steps in chemical milling

Residual stress relieving: If the part to be machined has residual stresses from the

s.

previous processing, these stresses first should be relieved in order to prevent warping
after chemical milling.

Preparing: The surfaces are degreased and cleaned thoroughly to ensure both good

te

adhesion of the masking material and the uniform material removal.

Masking: Masking material is applied (coating or protecting areas not to be etched).

Etching: The exposed surfaces are machined chemically with etchants.

Demasking: After machining, the parts should be washed thoroughly to prevent

no

further reactions with or exposure to any etchant residues. Then the rest of the

ww
w.
5s
t

Applications:

ar

masking material is removed and the part is cleaned and inspected.

Chemical milling is used in the aerospace industry to remove shallow layers of material from
large aircraft components missile skin panels (Figure 7), extruded parts for airframes.

Figure 7: Missile skin-panel section contoured by chemical milling to improve the

stiffness- to- weight ratio of the part (Kalpakjain & Schmid)

-9-

www.5starnotes.com

ww
w.
5s
t

ar

no

te

s.

co

www.5starnotes.com

-10-

www.5starnotes.com

www.5starnotes.com
Introduction

co

Electrochemical machining (ECM) is a metal-removal process based on the principle of

Electrochemical Machining (ECM)

reverse electroplating. In this process, particles travel from the anodic material (workpiece)

toward the cathodic material (machining tool). A current of electrolyte fluid carries away the

s.

deplated material before it has a chance to reach the machining tool. The cavity produced is

ar

no

te

the female mating image of the tool shape.

ww
w.
5s
t

Figure 8: ECM process

Similar to EDM, the workpiece hardness is not a factor, making ECM suitable for machining
difficult-to machine materials. Difficult shapes can be made by this process on materials
regardless of their hardness. A schematic representation of ECM process is shown in Figure
8. The ECM tool is positioned very close to the workpiece and a low voltage, high amperage
DC current is passed between the workpiece and electrode. Some of the shapes made by
ECM process is shown in Figure 9.

Figure 9: Parts made by ECM

-11-

www.5starnotes.com

www.5starnotes.com
Advantages of ECM

The components are not subject to either thermal or mechanical stress.

Fragile parts can be machined easily as there is no stress involved.
ECM deburring can debur difficult to access areas of parts.

s.

High surface finish (up to 25 m in) can be achieved by ECM process.

co

No tool wear during ECM process.

Complex geometrical shapes in high-strength materials particularly in the aerospace

machined repeatedly and accurately.

no

Deep holes can be made by this process.

Limitations of ECM

te

industry for the mass production of turbine blades, jet-engine parts and nozzles can be

ECM is not suitable to produce sharp square corners or flat bottoms because of the

ar

tendency for the electrolyte to erode away sharp profiles.

ECM can be applied to most metals but, due to the high equipment costs, is usually

ww
w.
5s
t

used primarily for highly specialised applications.

Material removal rate, MRR, in electrochemical machining:

MRR = C .I. h

(cm3/min)

C: specific (material) removal rate (e.g., 0.2052 cm3/amp-min for nickel);

I: current (amp);

h: current efficiency (90100%).

The rates at which metal can electrochemically remove are in proportion to the current passed
through the electrolyte and the elapsed time for that operation. Many factors other than
current influence the rate of machining. These involve electrolyte type, rate of electrolyte
flow, and some other process conditions.

-12-

www.5starnotes.com

www.5starnotes.com

UNIT IV

co

Ultrasonic Machining (USM)

Introduction

USM is mechanical material removal process or an abrasive process used to erode holes or

s.

cavities on hard or brittle workpiece by using shaped tools, high frequency mechanical

motion and an abrasive slurry. USM offers a solution to the expanding need for machining
brittle materials such as single crystals, glasses and polycrystalline ceramics, and increasing

te

complex operations to provide intricate shapes and workpiece profiles. It is therefore used
extensively in machining hard and brittle materials that are difficult to machine by traditional
manufacturing processes. The hard particles in slurry are accelerated toward the surface of

no

the workpiece by a tool oscillating at a frequency up to 100 KHz - through repeated

abrasions, the tool machines a cavity of a cross section identical to its own. A schematic

ww
w.
5s
t

ar

representation of USM is shown in Figure 10.

Figure 10: Schematic of ultrasonic machine tool

USM is primarily targeted for the machining of hard and brittle materials (dielectric or
conductive) such as boron carbide, ceramics, titanium carbides, rubies, quartz etc. USM is a
versatile machining process as far as properties of materials are concerned. This process is
able to effectively machine all materials whether they are electrically conductive or insulator.
For an effective cutting operation, the following parameters need to be carefully considered:

The machining tool must be selected to be highly wear resistant, such as high-carbon
steels.

-13-

www.5starnotes.com

www.5starnotes.com

The abrasives (25-60 m in dia.) in the (water-based, up to 40% solid volume) slurry

includes: Boron carbide, silicon carbide and aluminum oxide.

co

Applications
The beauty of USM is that it can make non round shapes in hard and brittle materials.

no

te

s.

Ultrasonically machined non round-hole part is shown in Figure 11.

Advantage of USM

ar

Figure 11: A non-round hole made by USM

USM process is a non-thermal, non-chemical, creates no changes in the microstructures,

ww
w.
5s
t

chemical or physical properties of the workpiece and offers virtually stress free machined
surfaces.

Any materials can be machined regardless of their electrical conductivity

Especially suitable for machining of brittle materials

Machined parts by USM possess better surface finish and higher structural integrity.

USM does not produce thermal, electrical and chemical abnormal surface

Some disadvantages of USM

USM has higher power consumption and lower material-removal rates than traditional

fabrication processes.

Tool wears fast in USM.

Machining area and depth is restraint in USM.

-14-

www.5starnotes.com

www.5starnotes.com
Introduction

co

Laser-beam machining is a thermal material-removal process that utilizes a high-energy,

LaserBeam Machining (LBM)

coherent light beam to melt and vaporize particles on the surface of metallic and non-metallic
workpieces. Lasers can be used to cut, drill, weld and mark. LBM is particularly suitable for

s.

making accurately placed holes. A schematic of laser beam machining is shown in Figure 12.
Different types of lasers are available for manufacturing operations which are as follows:
CO2 (pulsed or continuous wave): It is a gas laser that emits light in the infrared

te

region. It can provide up to 25 kW in continuous-wave mode.

Nd:YAG: Neodymium-doped Yttrium-Aluminum-Garnet (Y3Al5O12) laser is a solid-

no

state laser which can deliver light through a fibre-optic cable. It can provide up to 50

ww
w.
5s
t

ar

kW power in pulsed mode and 1 kW in continuous-wave mode.

Figure 12: Laser beam machining schematic

Applications

LBM can make very accurate holes as small as 0.005 mm in refractory metals ceramics, and
composite material without warping the workpieces. This process is used widely for drilling
and cutting of metallic and non-metallic materials. Laser beam machining is being used
extensively in the electronic and automotive industries.

-15-

www.5starnotes.com

Laser beam cutting (drilling)

In drilling, energy transferred (e.g., via a Nd:YAG laser) into the workpiece melts the

co

material at the point of contact, which subsequently changes into a plasma and leaves
the region.

A gas jet (typically, oxygen) can further facilitate this phase transformation and

s.

departure of material removed.

Laser drilling should be targeted for hard materials and hole geometries that are
difficult to achieve with other methods.

te

ww
w.
5s
t

ar

making a hole is shown in Figure 13.

no

A typical SEM micrograph hole drilled by laser beam machining process employed in

Figure 13: SEM micrograph hole drilled in 250 micro meter thick Silicon Nitride with 3rd
harmonic Nd: YAG laser

Laser beam cutting (milling)

A laser spot reflected onto the surface of a workpiece travels along a prescribed
trajectory and cuts into the material.

www.5starnotes.com

Continuous-wave mode (CO2) gas lasers are very suitable for laser cutting providing
high-average power, yielding high material-removal rates, and smooth cutting
surfaces.

-16-

www.5starnotes.com

www.5starnotes.com

Advantage of laser cutting

No limit to cutting path as the laser point can move any path.

The process is stress less allowing very fragile materials to be laser cut without any

Very hard and abrasive material can be cut.

Sticky materials are also can be cut by this process.

It is a cost effective and flexible process.

High accuracy parts can be machined.

No cutting lubricants required

No tool wear

Narrow heat effected zone

no

ar

Limitations of laser cutting

te

s.

support.

Uneconomic on high volumes compared to stamping

Limitations on thickness due to taper

ww
w.
5s
t

High capital cost

High maintenance cost

Assist or cover gas required

co

-17-

www.5starnotes.com

www.5starnotes.com
UNIT V

Water Jet Cutting

co

Introduction

Water jet cutting can reduce the costs and speed up the processes by eliminating or reducing

expensive secondary machining process. Since no heat is applied on the materials, cut edges

s.

are clean with minimal burr. Problems such as cracked edge defects, crystalisation,
hardening, reduced wealdability and machinability are reduced in this process.

te

Water jet technology uses the principle of pressurising water to extremely high pressures, and
allowing the water to escape through a very small opening called orifice or jewel. Water
jet cutting uses the beam of water exiting the orifice to cut soft materials. This method is not

no

suitable for cutting hard materials. The inlet water is typically pressurised between 1300
4000 bars. This high pressure is forced through a tiny hole in the jewel, which is typically

ww
w.
5s
t

ar

o.18 to 0.4 mm in diameter. A picture of water jet machining process is shown in Figure 14.

Figure 14: Water jet cutting

(http://www.waterjets.org/about_abrasivejets.html)

Applications
Water jet cutting is mostly used to cut lower strength materials such as wood, plastics and
aluminium. When abrasives are added, (abrasive water jet cutting) stronger materials such as
steel and tool steel can be cut.

-18-

www.5starnotes.com

Advantages of water jet cutting

There is no heat generated in water jet cutting; which is especially useful for cutting

co

tool steel and other metals where excessive heat may change the properties of the
material.

Unlike machining or grinding, water jet cutting does not produce any dust or particles
that are harmful if inhaled.
Other advantages are similar to abrasive water jet cutting

te

Disadvantages of water jet cutting

One of the main disadvantages of water jet cutting is that a limited number of
materials can be cut economically.

no

s.

Thick parts cannot be cut by this process economically and accurately

Taper is also a problem with water jet cutting in very thick materials. Taper is when

ar

the jet exits the part at different angle than it enters the part, and cause dimensional

ww
w.
5s
t

inaccuracy.

www.5starnotes.com

-19-

www.5starnotes.com

www.5starnotes.com

Abrasive Water-Jet Cutting

co

Introduction

Abrasive water jet cutting is an extended version of water jet cutting; in which the water jet

contains abrasive particles such as silicon carbide or aluminium oxide in order to increase the

s.

material removal rate above that of water jet machining. Almost any type of material ranging

from hard brittle materials such as ceramics, metals and glass to extremely soft materials such
as foam and rubbers can be cut by abrasive water jet cutting. The narrow cutting stream and

te

computer controlled movement enables this process to produce parts accurately and

efficiently. This machining process is especially ideal for cutting materials that cannot be cut

no

by laser or thermal cut. Metallic, non-metallic and advanced composite materials of various
thicknesses can be cut by this process. This process is particularly suitable for heat sensitive
materials that cannot be machined by processes that produce heat while machining.

ar

The schematic of abrasive water jet cutting is shown in Figure 15 which is similar to water jet
cutting apart from some more features underneath the jewel; namely abrasive, guard and
mixing tube. In this process, high velocity water exiting the jewel creates a vacuum which

ww
w.
5s
t

sucks abrasive from the abrasive line, which mixes with the water in the mixing tube to form
a high velocity beam of abrasives.

1. Figure 15: Abrasive water jet machining

(http://www.waterjets.org/about_abrasivejets.html)
-20-

www.5starnotes.com

co

www.5starnotes.com

Applications

Abrasive water jet cutting is highly used in aerospace, automotive and electronics industries.

s.

In aerospace industries, parts such as titanium bodies for military aircrafts, engine

components (aluminium, titanium, heat resistant alloys), aluminium body parts and interior

te

cabin parts are made using abrasive water jet cutting.

In automotive industries, parts like interior trim (head liners, trunk liners, door panels) and
fibre glass body components and bumpers are made by this process. Similarly, in electronics

no

industries, circuit boards and cable stripping are made by abrasive water jet cutting.
Advantages of abrasive water jet cutting

In most of the cases, no secondary finishing required

No cutter induced distortion

Low cutting forces on workpieces

Limited tooling requirements

ww
w.
5s
t

ar

Little to no cutting burr

Typical finish 125-250 microns

Smaller kerf size reduces material wastages

No heat affected zone

Localises structural changes

No cutter induced metal contamination

Eliminates thermal distortion

No slag or cutting dross

Precise, multi plane cutting of contours, shapes, and bevels of any angle.

Limitations of abrasive water jet cutting

Cannot drill flat bottom

Cannot cut materials that degrades quickly with moisture

Surface finish degrades at higher cut speeds which are frequently used for rough
cutting.
-21-

www.5starnotes.com

www.5starnotes.com

The major disadvantages of abrasive water jet cutting are high capital cost and high

co

noise levels during operation.

ww
w.
5s
t

ar

no

te

s.

A component cut by abrasive water jet cutting is shown in Figure 16. As it can be seen, large
parts can but cut with very narrow kerf which reduces material wastages. The complex shape
part made by abrasive water jet cutting is shown in Figure 17.

Figure 16: Abrasive water jet cutting

Figure 17: Steel gear and rack cut with an abrasive water jet

-22-

www.5starnotes.com

References

co

2. Manufacturing Engineering and Technology Fifth Edition - Serope Kalpakjian and

www.5starnotes.com

Steven R Sschmid. (Prentice Hall), 2006.

3. Manufacturing Technology, Volume 2. R L Timings & S P Wilkinson (Longman)

s.

2000.

4. Manufacturing Processes and Equipment George Tlusty (Prentice Hall).

te

5. E. Paul DeGarmo, J.T. Black, R.A. Kohsern, Materials and Processes in

Manufacturing, 8th ed., Prentice-Hall, Englewood Cliffs, NJ, 1997, pp. 941947.
6. Chemical Machining, Metals Handbook, vol. 3, Machining, 8th ed., American Society

no

for Metals, Metals Park, OH, pp. 240248.

7. http://www.dimeg.unipd.it/didattica/31/8_Non_conventional.pdf
8. www.eng.morgan.edu

ar

9. http://www.answers.com/topic/electrical-discharge-machining
10. http://www.exitech.co.uk/pdfFiles/Microhole%20Drilling%20using%20Reshaped%2
0Pulsed%20Gaussian%20Laser%20Beam.pdf

ww
w.
5s
t

11. http://www.google.co.uk/search?q=ultrasonic+machining+picture&hl=en&start=10&
sa=N
12. http://www.ebtecwelding.com/waterjet-cutting/wjetlimitations.html
13. http://www.waterjets.org/about_abrasivejets.html
14. http://www.waterjets.org/index.html

Lecture notes on non-traditional machining processes by:

Dr. H. N. Dhakal

Lecturer in Mechanical and Marine Engineering,

School of Engineering,
University of Plymouth
October 2007

-23-

www.5starnotes.com