Scribd
Upload
45 views

Extended Access Lists

Extended access lists allow filtering of source and destination IP addresses as well as protocol ports, offering more flexibility than standard access lists. They can be applied to the interface closest to the source network to immediately filter packets and conserve bandwidth. To use an extended ACL, you first create the access list specifying the source, destination, and port, then apply it inbound or outbound on the appropriate interface.

Uploaded by

Senan Alkaaby
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
45 views

Extended Access Lists

Extended access lists allow filtering of source and destination IP addresses as well as protocol ports, offering more flexibility than standard access lists. They can be applied to the interface closest to the source network to immediately filter packets and conserve bandwidth. To use an extended ACL, you first create the access list specifying the source, destination, and port, then apply it inbound or outbound on the appropriate interface.

Uploaded by

Senan Alkaaby
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Extended Access Lists - ACL

Overview
Extended access lists offer greater flexibility than standard access list due to the fact that you can filter,
not only source IP addresses, but also destination IP addresses, as well as other protocols ports and
services, like TCP port 23 telnet for instance. Since you are able to declare both the source and the
destination addresses, you can apply the extended ACL on the router that is closest to the source
network, this allows you to immediately filter packets from the network, without allowing them to
traverse the entire network before being filtered and dropped; applied in this way extended ACLs can
conserve bandwidth and router resources.

Two Steps:
1. create the access list (standard or extended)
2. apply the access list to an interface (inbound or outbound)
1. Create:
Standard ACL (1-99, and 2000-2699):
denies or permits: 1) source IP address
Extended ACL (100-199):
denies or permits: 1) source IP address, 2) destination IP address, 3) port (service) (optional)

2. Apply:
Where to apply an ACL?
A standard ACL is applied inbound or outbound on the router interface that is closest to the destination
of the traffic.
An extended ACL is applied inbound or outbound on the router interface that is closest to the source of
the traffic.
IOS Commands
Extended access list command formats:
access-list <100-199> <deny | permit> <protocol> <source ip address> <wildcard bits> <destination ip
address> <wildcard bits> <operator> <port or service>
access-list <100-199> <deny | permit> <protocol> host <source ip address> host <destination ip
address> <operator> <port or service>
access-list <100-199> <deny | permit> <protocol> <source ip address> <wildcard bits> <destination ip
address> <wildcard bits>

Extended access list examples:


Deny and permit a source class c network to a destination class c network:
router(config)#access-list 100 deny ip 192.168.1.0 0.0.0.255 192.168.4.0 0.0.0.255
router(config)#access-list 100 permit ip 192.168.2.0 0.0.0.255 192.168.4.0 0.0.0.255

Deny or permit a source host to a destination /24 network:


router(config)#access-list 100 deny ip 192.168.1.100 0.0.0.0 192.168.4.0 0.0.0.255
router(config)#access-list 100 deny ip host 192.168.1.100 192.168.4.0 0.0.0.255
router(config)#access-list 100 permit ip 192.168.1.101 0.0.0.0 192.168.4.0 0.0.0.255
router(config)#access-list 100 permit ip host 192.168.1.101 192.168.4.0 0.0.0.255

Deny or permit any host to any destination on port 80 (http):


router(config)#access-list 100 deny tcp any any eq 80
router(config)#access-list 100 permit tcp any any eq 80

Deny or permit all hosts:


router(config)#access-list 100 deny any any
router(config)#access-list 100 permit any any

Apply the access list to a router interface outbound and inbound


router(config)#interface fastethernet 0/0
router(config-if)#ip access-group 100 out
router(config)#interface fastethernet 0/1
router(config-if)#ip access-group 100 in

You might also like