Chapter 3

CONTINUOUS WAVE AND

FREQUENCY MODULATED
RADAR
Keywords. CW radar, Doppler frequency shift

3.1

THE DOPPLER EFFECT

A radar detects the presence of objects and locates their position in space
by transmitting electromagnetic energy and observing the returned echo.
A pulse radar transmits a relatively short burst of electromagnetic energy,
after which the receiver is turned on to listen for the echo. The echo not
only indicates that a target is present, but the time that elapses between the
transmission of the pulse and the reception of its echo is a measure of the
distance to the target. Separation of the echo signal from the transmitted
signal is made on the basis of dierences in time.
The radar transmitter may be operated continuously rather than pulsed
if it is possible to separate the strong transmitted signal from the weak echo.
30

The received echo-signal power is considerably smaller than the transmitter

power (as low as 1018 times the transmitter power - or sometimes even less).
Separate antennas for transmission and reception help isolate the weak echo
from the strong leakage signal, but this isolation is usually not sucient.
A feasible technique for separating the received signal from the transmitted
signal, when there is relative motion between radar and target, is based on
recognizing the change in the echo-signal frequency caused by what is known
as the doppler eect.
It is well known in the eld of optics and acoustics that if there is relative
motion between the source of a signal and the observer of the signal, along
the line joining the two, then an apparent shift in frequency will result. This
is the doppler eect and is the basis of CW (Continuous Wave) radars.
Consider Fig.3.1 above in which a CW radar and a target are placed at a
distance of R from each other. The target is moving with a speed Vr relative
to the radar and along the line joining the radar and the target (also known
as the line-of-sight - LOS). Note that the transmitted signal is not in the form
of a train of pulses (as in Chapter 2) but a continuous wave with frequency
fo . Let the total number of wavelengths (given by ) contained in the to-and
-fro path between the radar and the target be denoted by n. Then,

n=

2R

(3.1)

One wavelength corresponds to an angular excursion of 2 radians.Thus,

the total angular excursion made by the electromagnetic wave during its
transit to the target and back to the radar is

4R
2R
.2 =

(3.2)

When the target is in motion, both R and are changing. Now a change
31

Figure 3.1: The doppler eect

in with respect to time is equal to an angular frequency. This, in fact, is
the doppler angular frequency Wd ,

Wd = 2fd =

4 dR
4Vr
d
=
.
=
dt
dt

(3.3)

2Vr fo
2Vr
=

(3.4)

From which we get

fd =

32

Where,
fd = doppler frequency shift, in Hz
c = velocity of propagation = 3 108 m/s
Vr = relative velocity of the target with respect to the radar along the
line-of-sight.
For a stationary radar and a moving target the relative velocity may be
written as

Vr = V cos

(3.5)

where, V is the target speed and is the angle made by the target velocity
vector with the LOS. When = 0, the doppler frequency is a maximum.
The doppler frequency is zero when the trajectory is perpendicular to the
radar-target line-of-sight (that is, =

= 90o ). Also note that the doppler

frequency shift positive for an approaching target (that is, Vr is considered

to be positive) and negative for a receding target (that is, Vr is considered
to be negative).
EXAMPLE 3.1: Positions of the two aircraft, A and B, are as shown in
the gure below. Aircraft A has a speed of 600 m/sec and carries a CW
radar transmitting at 300 MHz frequency and tracking aircraft B which has
a speed of 800 m/sec.
(a) What is the doppler frequency shift recorded by the radar in aircraft
A?
(b) Is this shift positive or negative?
(c) What should be the ight direction of aircraft B for the doppler frequency shift to be zero?

33

ANSWER
(a) The transmitted frequency = f0 = 300M Hz = 300 106 Hz.
The relative velocity of aircraft A with respect to aircraft B along the
LOS is given by,
vr = 600 cos 450 + 800 cos 300 = 1117.08m/sec.

(3.6)

The doppler frequency shift

= fd =

2 1117.08 300 106

2vr f0
=
= 2234.16Hz
c
3 108

(3.7)

(b) Note that aircraft B is actually moving towards aircraft A in a relative

sense and hence it is an approaching target, that is, the LOS between A and
B is shrinking with time. Thus, the doppler shift is positive, which means
34

that the frequency of the received signal is more than the frequency of the
transmitted signal.
(c) The doppler frequency shift will be zero when the relative velocity vr
is zero. This can happen when
Vr = 600cos450 800cos = 0.

(3.8)

= 57.970 .

(3.9)

From which we get

This is shown in the gure given below.

Thus, the change in frequency between the transmitted signal and the
received signal allows the received signal to be separated from the trans35

mitted signal. Apart from this, the CW radar also provides a measurement
of relative velocity which may be used to distinguish moving targets from
stationary objects and clutter.
The expression for doppler frequency shift given in (3.4) is somewhat
approximate, though it serves quite well for most practical purposes. The
correct expression for the frequency f of the echo signal from a target,
moving with relative velocity Vr , when the transmitted frequency is fo , is
given by
f = f0 .

1 + Vr /c
1 Vr /c

(3.10)

which, on expansion by Taylors series and truncation beyond the rst

order term, reduces to
f = f0 (1 + 2Vr /c)

(3.11)

Truncation beyond the rst order terms is justied when vr  c (which

is usually the case and implies that vr /c is a very small quantity). This, in
turn, yields the expression for doppler frequency shift given in (3.4). The
phase shift associated with the return signal is
(4f0 R)/c
(1 Vr /c)

3.2

(3.12)

THE CW RADAR

In Fig. 3.2 we give the block diagram of a simple CW radar.

The transmitter generates a continuous (unmodulated) oscillation of frequency f0 , which is radiated by the antenna. A portion of the radiated energy
36

is intercepted by the target and is scattered. some of it in the direction of

the radar, where it is collected by the receiving antenna. If the target is in
motion with a velocity Vr relative to the radar, the received signal frequency

Figure 3.2: A simple CW radar block diagram

will be shifted from the transmitted signal frequency f0 by an amount fd .
The plus sign applies if the distance between the radar and the target is
decreasing (that is, an approaching target) and the minus sign applies when
this distance is increasing (that is, a receding target). The received echo
signal at a frequency f0 fd enters the radar via the antenna and is hetero37

dyned in the detector (mixer) with a portion of the transmitted signal f0 to

produce a doppler beat note of frequency fd . However, the sign of fd is lost
in this process.
The purpose of the doppler amplier (beat frequency amplier) is to
eliminate echoes from stationary targets and to amplify the doppler echo
signal to a level where it can operate and indicating device. Its frequency
response characteristics is as shown in Fig. 3.2(b). The low-frequency cuto must be high enough to reject the d-c component caused by stationary
targets, and yet it must be low enough to pass the smallest doppler frequency
expected. Sometimes both conditions cannot be met simultaneously and a
compromise is necessary. The doppler cuto frequency (on the higher side)
is usually selected to pass the highest doppler frequency expected.
The indicator could be a pair of earphones or a frequency meter. Earphones are used when an exact knowledge of the doppler frequency is not
required. The ear then acts as a selective (narrow) bandpass lter with a
passband of the order of 50 Hz centered about the signal frequency. This is
of use for subsonic aircraft targets when the transmitter frequency falls in
the middle range of the microwave frequency region.
If audio detection is desired for those combination of target velocity and
transmitter frequency which do not result in audible doppler frequencies,
the doppler signal could be heterodyned to the audible range. The doppler
frequency can be detected and measured by conventional frequency meters,
usually one that counts cycles.

38

3.3

ISOLATION BETWEEN TRANSMITTER

AND RECEIVER

A single antenna serves the purpose of both transmission and reception in the
simple CW radar described above. Though, in principle, a single antenna is
sucient as the necessary isolation is obtained by the separation in frequency
(as a result of doppler eect), in practice there is considerable transmitter
leakage. But this leakage is benecial too since it supplies the reference frequency necessary for the detection of the doppler frequency shift. Otherwise
a sample of the transmitted signal must be made available at the receiver.
However, there are two reasons why the amount of transmitter leakage power
should be kept at a low value.
The maximum power the receiver input circuitry can withstand, without being physically damaged or having its sensitivity reduced, is quite
low.
The transmitter noise which enters the receiver from the transmitter
reduces receiver sensitivity.
The amount of isolation required depends on the transmitter power and
the accompanying transmitter noise as well as the ruggedness and sensitivity
of the receiver. If the safe value of power which might be applied to a receiver
were 10mw and if the transmitter power were 1 kw, the isolation between
transmitter and receiver must be at least 50 dB.
In long range CW applications, it is the level of the noise accompanying
the transmitter leakage signal, rather than the damage this leakage might
cause to the receiver circuitry, which determines the amount of isolation
required. For example, suppose the isolation between the transmitter and
receiver were such that 10mw of leakage signal appeared at the receiver. If
39

the minimum detectable signal were 1013 watt, the transmitter noise must
be at least 110 dB below the transmitted carrier.

3.4

SIGN OF THE RADIAL VELOCITY

In many applications of CW radar it is of interest to know if the target is approaching or receding. This might be determined with separate lters located
on either side of the intermediate frequency.If the echo-signal frequency lies
below the carrier, then the target is receding; whereas if the echo frequency
is greater that the carrier, then the target is approaching. This is shown in
Fig. 3.3 given below. However, the doppler-frequency spectrum folds over
in the video because of the action of the detector, and hence the information
about whether the doppler shift is positive or negative is lost. But it is possible to determine its sign from a technique borrowed from single-sideband
communication. If the transmitter signal is given by,
Et = Eo cos wo t
The echo signal from the moving target will be,
Er = K1 E0 cos [(wo + wd )t + ]
where, E0 = amplitude of the transmitted signal
K1 = a constant determined from the radar equation
representing the reduction in power of the echo signal
wo = angular frequency of transmitted signal, rad/sec
wd = dopper angular frequency shift, rad/sec
= a constant phase shift, which depends upon the range
of initial detection (i.e., distance between the radar and the target)

40

Figure 3.3: Transmitted and received signal frequency

The sign of the doppler frequency, and therefore the direction of target
motion, may be found by splitting the received signal into two channels as
shown in Fig.3.4.
In channel A the signal is processed as in a simple CW radar. The receiver
signal and a portion of the transmitter signal heterodyne in the detector
(mixer) to yield a dierence signal,
EA = K2 E0 cos(wd t + )
41

Figure 3.4: Determination of the sign of the Doppler frequency

The channel B has

phase delay introduced in the reference signal. The

output of the channel B mixer is,

EB = K2 E0 cos(wd t + +

)
2

(3.13)

If the target is approaching (positive doppler),the outputs from the two channels are,
EA = K2 E0 cos(wd t + )

EB = K2 E0 cos(wd t + + )
2
on the other hand, if the target is receding (negative doppler),
EA () = K2 E0 cos(wd t + )
42

(3.14)
(3.15)

(3.16)


)
(3.17)
2
the sign of wd and the direction of the targets motion may be determined
according to whether the output of channel B leads or lags the output of
EB () = K2 E0 cos(wd t + +

channel A. One method of determining the relative phase relationship between the two channels is to apply the outputs of the two channels to a
synchronous two-phase motor. The direction of the motors rotation is an
indication of the direction of the targets motion.

43